CRA06E, CRA06S
www.vishay.com Vishay
End of Life - Last Available Purchase Date: 31-Dec-2019
Revison: 25-Feb-2019 1Document Number: 31002
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Thick Film Chip Resistor Array
CRA06E and CRA06S Thick Film resistor arrays are
constructed on a high grade ceramic body with convex
terminations. A small package enables the design of high
density circuits. The single component reduces board
space, component counts and assembly costs.
FEATURES
• Convex terminal array available with either
scalloped corners (E version) or square corners
(S version)
• Wide ohmic range: 10 to 1 M
• 4 or 8 terminal package with isolated resistors
• AEC-Q200 qualified
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Notes
(1) Rated voltage:
(2) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rates dissipation applies only if the permitted film temperature of 155 °C is not exceed
Notes
(1) Preferred way for ordering products is by use of the PART NUMBER
(2) Please refer to table PACKAGING, see next page
STANDARD ELECTRICAL SPECIFICATIONS
MODEL CIRCUIT
POWER RATING
P70
W
LIMITING ELEMENT
VOLTAGE MAX.
V
TEMPERATURE
COEFFICIENT
± ppm/K
TOLERANCE
± %
RESISTANCE
RANGE
SERIES
CRA06E
CRA06S
03 0.063 50 100 1 10R to 1M E24; E96
200 2; 5 E24
Zero-Ohm-Resistor: Rmax. = 50 m, Imax. = 1 A
TECHNICAL SPECIFICATIONS
PARAMETER UNIT CRA06E AND CRA06S
Rated dissipation at 70 °C (1) W per element 0.063
Limiting element voltage (2) V50
Insulation voltage (1 min) VDC/AC PEAK 100
Category temperature range °C -55 to +155
Insulation resistance > 109
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRA06S08347K0JTA (1)
MODEL TERMINAL STYLE PIN CIRCUIT VALUE TOLERANCE PACKAGING (2) SPECIAL
CRA06 S
E
04
08
3 = 03 R = decimal
K = thousand
M = million
0000 = 0 jumper
F = ± 1 %
G = ± 2 %
J = ± 5 %
Z = 0 jumper
TA
TC
Up to 2 digits
Product Description: CRA06S 08 03 -05 473 J RT1 e3
CRA06S 08 03 473 J RT1 e3
MODEL TERMINAL COUNT CIRCUIT TYPE RESISTANCE VALUE TOLERANCE PACKAGING LEAD (Pb)-FREE
CRA06E
CRA06S
04
08
03 1R0 = 1
10R = 10
47K = 47 k
1M0 = 1 M
0R0 = jumper
F = ± 1 %
G = ± 2 %
J = ± 5 %
Z = 0 jumper
RT1
RT6
e3 = pure tin
termination finish
First two digits (3 for
1 %) are significant. Last
digit is the multiplier
P x R
A06S 8340CR JAK0T7
CRA06E, CRA06S
www.vishay.com Vishay
End of Life - Last Available Purchase Date: 31-Dec-2019
Revison: 25-Feb-2019 2Document Number: 31002
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CIRCUIT
DIMENSIONS
AVAILABLE TYPES AND RANGES
MODEL TERMINAL COUNT CIRCUIT TEMPERATURE
COEFFICIENT TOLERANCE
CRA06S
04 03 ± 100 ppm/K ± 1 %
± 200 ppm/K ± 2 %; ± 5 %
08 03 ± 100 ppm/K ± 1 %
± 200 ppm/K ± 2 %; ± 5 %
CRA06E 08 03 ± 100 ppm/K ± 1 %
± 200 ppm/K ± 2 %; ± 5 %
PACKAGING
MODEL TAPE WIDTH PITCH PIECES / REEL
PACKAGING CODE
PAPER TAPE
PART NUMBER PRODUCT
DESCRIPTION
CRA06 180 mm/7" 4 mm 5000 TA RT1
330 mm/13" 4 mm 20 000 TC RT6
03 CIRCUIT
4 pin 8 pin
Derating
Ambient Temperature in °C
Rated Power in %
-55 0 50 100 155
70
0
40
100
120
80
60
20
-25 25 125
S-Version
1
PIN 1
ee a a
103
E-Version
103
MODEL PIN
NO#
DIMENSIONS in millimeters
LA
A1
BB*PTW
CRA06S 4
1.6 0.38 0.61 0.3 0.3 0.8 0.5 1.5
CRA06E 8
3.2 0.38 - 0.3 0.3 0.8 0.5 1.5
CRA06S 8
3.2 0.38 0.61 0.3 0.3 0.8 0.5 1.5
TOL.
± 0.15 ± 0.15 ± 0.15 ± 0.15 ± 0.15 ± 0.1 ± 0.1 ± 0.15
REFLOW SOLDER PAD DIMENSIONS in millimeters
MODEL PINS c w d p a b e
CRA06S 4 0.8 3.1 0.36 0.44 1.15
CRA06E
CRA06S 8 0.8 3.1 0.36 0.8 0.44 1.15 0.63
CRA06E, CRA06S
www.vishay.com Vishay
End of Life - Last Available Purchase Date: 31-Dec-2019
Revison: 25-Feb-2019 3Document Number: 31002
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
(1) Figures are given for a single element
(2) Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
TEST
(clause) CONDITIONS OF TEST
REQUIREMENTS
PERMISSIBLE CHANGE (R/R) (1)
STABILITY
CLASS 1 OR BETTER
STABILITY
CLASS 2 OR BETTER
Stability for product types: 10 to 1 M10 to 1 M
CRA06E / CRA06S
Resistance (4.5) - ± 1 % ± 2 %; ± 5 %
Temperature coefficient (4.8.4.2) (20 / -55 / 20) °C and
(20 / 125 / 20) °C ± 100 ppm/K ± 200 ppm/K
Overload (4.13) U = 2.5 x (P70 x R)1/2
2 x Umax.; 0.5 s ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
Solderability (4.17.5) (2)
Aging 4 h at 155 °C, dry heat
solder bath method; 235 °C; 2 s
visual examination
Good tinning ( 95 % covered)
no visible damage
Resistance to soldering heat (4.18.2) Solder bath method;
(260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
Rapid change of temperature (4.19) 30 min at LCT = -55 °C;
30 min at UCT = 125 °C; 5 cycles ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
Damp heat, steady state (4.24) (40 ± 2) °C; 56 days;
(93 ± 3) % RH ± (1 % R + 0.05 )± (2 % R + 0.1 )
Climatic sequence (4.23)
16 h at UCT = 125 °C; 1 cycle at 55 °C;
2 h at LCT = -55 °C;
1 h/1 kPa at 15 °C to 35 °C;
5 cycles at 55 °C
U = (P70 x R)1/2
U = Umax.; whichever is less severe
± (1 % R + 0.05 )± (2 % R + 0.1 )
Endurance at 70 °C (4.25.1)
U = (P70 x R)1/2
U = Umax.; whichever is less severe
1.5 h ON; 0.5 h OFF;
70 °C; 1000 h
± (1 % R + 0.05 )± (2 % R + 0.1 )
Extended endurance (4.25.1.8) Duration extended to 8000 h ± (2 % R + 0.1 )± (4 % R + 0.1 )
Endurance at upper category
temperature (4.25.3) UCT = 125 °C; 1000 h ± (1 % R + 0.05 )± (2 % R + 0.1 )
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
• EN 140401-802
• IEC 60068-2-X
• EIA 481
Generic specification
Sectional specification
Detail specification
Variety of environmental test procedures
Packaging of SMD components
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 08-Feb-17 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
