TB62756FUG TOSHIBA BiCD Digital Integrated Circuit Silicon Monolithic TB62756FUG Step-up Type DC/DC Converter for White LEDs The TB62756FUG is a high efficiency step-up type DC/DC converter that is designed especially for use as a constant current driver of white LEDs. It is possible to drive 2 to 6 white LEDs connected in series using a lithium-ion battery. This IC incorporates an N-ch-MOS FET required for switching of an external inductor. The forward current of the LEDs can be controlled by an external resistor. This IC is best suited for use as a driver of white LED back Weight: 0.016 g (typ.) lighting in color LCDs in PDAs, cellular phones and handy terminal devices. The suffix (G) appended to the part number represents a Lead(Pb)-Free product. Features * Can drive 2 to 6 white LEDs connected series * Variable LED current IF is set with a external resistor: 20 mA (typ.) @RSENS = 16 * Output power: Available for 400 mW LED loading * High efficiency: 87% @Maximum * IC package: SSOP6-P-0.95 (SOT23-6) * Switching frequency: 1.1 MHz (typ.) 1 2006-06-14 TB62756FUG Block Diagram SW NC 4 2 VIN 3 Monostable multivibrator for reference Monostable multivibrator for off time control CTL AMP. Circuit on/off 6 FB Error AMP. SHDN 1 5 GND Pin Assignment (top view) SHDN 1 Q (NC) 2 6 FB 5 GND VIN 3 4 SW Note 1: The IC may break if mounted 180 degrees in reverse. Ensure the device is correctly orientated before assembley. Pin Functions No. Symbol Function 1 SHDN 2 NC No connection or connected to GND. 3 VIN Supply voltage pin. Supply voltage range: 2.8 V to 5.5 V 4 SW DC-DC converter switching pin - switch incorporates N-ch MOSFET. 5 GND Ground pin. 6 FB Input pin for IC ON/OFF control. SHDN = H Operation Mode, SHDN = L Shutdown Mode (IC shutdown) Please do not open this terminal. (Note 2) Connected to the cathode of LED. Note 2: The NC terminal is not connected to the internal circuit. 2 2006-06-14 TB62756FUG I/O Equivalent Pin Circuits 1. SHDN Pin 2. NC Pin NC 2 VIN SHDN 1 The NC pin is not connected to any internal circuit. 3. SW Pin 4. FB Pin SW 4 VIN FB 6 3 2006-06-14 TB62756FUG Application Circuit Example 4.7 to 10 H VIN NC SW 4 2 3 Monostable multivibrator for off time control 1 F 2.2 F Monostable multivibrator for reference VZ = 24 V VIN CTL AMP. 500 6 Error AMP. FB 16 @20 mA Circuit on/off SHDN 1 PWM 5 GND Protection at the Time of LED Opening The zener diode in the application circuit example is necessary for the provision of over-voltage protection for when the LED becomes open. As the IC does not incorporate a voltage protection circuit, it is strongly advised that a zener diode be connected. The zener diode should satisfy the following conditions: i) Less than maximum output voltage of 24 V ii) Greater than the total series LED VF iii) Less than the maximum output capacitance C2. Moreover, by connecting a protection circuit such as RZD in the figure below, it is possible to control the output current when the LED becomes open, and to use a zener diode of lower tolerance. An example of IZD control by RZD connection. (RSENS = 16 ) S-Di RZD () IZD (mA) 500 0.6 (typ.) 100 2.8 (typ.) SW IF IZD 1 F C2 RZD GND FB In order to avoid adverse effects on driver characteristics, Toshiba recommends a resistance of 500 or less. RSENS Protection Circuit Application 4 2006-06-14 TB62756FUG Output-side Capacitor Setting It is recommended that the value of C2 be equal to, or greater than 1.0 (F). External Inductor Size Setting For each number of LEDs, the selected inductance should be greater than the value indicated in the table below. Number of LEDs Inductance (Unit: H) 2 4.7 Note 3 6.8 4 IF = 20 mA 5 10 6 Control of IF The resistance RSENS is connected between the FB pin and the GND pin. The average current is controlled by the RSENS value, and calculated using the following equation: IF (mA) = [325 mV/RSENS ()] Margin of error is 5%. Dimming using PWM Signal Input A dimming function can also by applied using a PWM signal. [Notes] * When using a PWM signal, the minimum pulse width of the PWM should be greater than 33 s. * Duty ratio of PWM function should be set at 10% to 90%. * The recommended PWM frequency should be 100 Hz to 10 kHz. <<Output current is calculated using the following equation>> IF ( mA ) = 325 [mV ] x ON Duty [%] RSENS [] 5 2006-06-14 TB62756FUG Absolute Maximum Ratings (Ta = 25C, unless otherwise specified) Characteristics Symbol Ratings Unit VIN -0.3 to 6.0 V Input voltage V SHDN -0.3 to VIN + 0.3 Switching pin voltage VO (SW) Power supply voltage (Note 1) -0.3 to 24 V V 0.41 (IC only) Power dissipation PD W 0.47 (IC mounted on PCB) (Note 2) Rth (j-a) 1 300 (IC only) Rth (j-a) 2 260 (IC mounted on PCB) Operating temperature range Topr -40 to 85 C Storage temperature Tstg -55 to 150 C Tj 150 C Thermal resistance Maximum junction temperature C/W Note 1: However, do not exceed 6 V. Note 2: Power dissipation is reduced by 3.8 mW/C from the absolute maximum rating for every 1C exceeding the ambient temperature of 25C (when the IC is mounted on a PCB). Recommended Operating Condition (Ta = -40 to 85C, unless otherwise specified) Characteristics Symbol Test Conditions Min Typ. Max Unit Power supply voltage VIN 2.8 5.5 V SHDN pin input pulse width tpw 33 s LED current (Average value) IF1 20 mA "H", "L" duty width VIN = 3.6 V, RSENS = 16 4 white LEDs, Ta = 25C Electrical Characteristics (Ta = 25C, VIN = 2.8 to 5.5 V, unless otherwise specified) Characteristics Symbol Test Conditions Min Typ. Max Unit Operating consumption current IIN (ON) VIN = 3.6 V, RSENS = 16 0.9 1.5 mA Standby consumption current IIN (OFF) VIN = 3.6 V, V SHDN = 0 V 0.5 1.0 A SHDN pin H level input voltage V SHDN H 1.3 VIN V SHDN pin L level input voltage V SHDN L 0 0.4 V -10 0 10 A 0.77 1.1 1.43 MHz 25 V IO (SW) 400 mA IOZ (SW) 0.5 1 A 308 325 342 mV -5 5 % ISHDN VIN = 3.6 V, V SHDN = 3.6 V Integrated MOS-FET switching frequency fOSC VIN = 3.6 V, V SHDN = 3.6 V Switching pin protection voltage VO (SW) Switching pin current Switching pin leakage current SHDN pin current FB pin feedback voltage FB pin line regulation VFB VFB VIN = 3.6 V, RSENS = 16 L = 4.7 H VIN = 3.6 V center VIN = 3.0 V to 5.0 V 6 or 0V 2006-06-14 TB62756FUG 1. Application Circuit Example and Measurement Data (reference data) VIN = 2.8 to 5.5 V L1 S-Di * Evaluation conditions (Ta = 25C) WLEDs 2 to 6 SW SHDN FB RSENS = 16 GND : CXLD120 series (NEO MAX CO.,Ltd.) (Size: 2.5 mm x 3.0 mm x 1.2 mm) C1 : C2012JB1E225K (TDK Corp.) : C2012JB1E105K (TDK Corp.) C2 S-Di : CUS02 1 A/30 V (TOSHIBA Corp.) WLEDs : NSCW215T (NICHIA Corp.) L1 C2 = 1.0 F Input Voltage - Efficiency/Output Current 5LED Drive, L=10H 100 30 90 30 90 25 80 25 80 IF (mA) IOUT(mA) 70 20 IIOUT F Efficiency 15 10 2.8 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 IF (mA) IOUT(mA) 35 Efficiency(%) 100 35 70 20 60 15 50 10 5.5 IIOUT F Efficiency 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 5.5 VIN(V) Input Voltage - Efficiency/Output Current 3LED Drive, L=6.8H Input Voltage - Efficiency/Output Current 6LED Drive, L=10H 100 35 100 30 90 30 90 25 80 70 20 IIOUT F Efficiency 15 10 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 IOUT(mA) IF (mA) 35 Efficiency(%) IF (mA) IOUT(mA) 60 50 2.8 VIN(V) 2.8 Efficiency(%) Input Voltage - Efficiency/Output Current 2LED Drive, L=4.7H 80 25 70 20 60 15 50 10 IIOUT F Efficiency 60 50 2.8 5.5 Efficiency(%) C1 = 2.2 F VIN 3.1 3.4 3.7 4 VIN(V) 4.3 4.6 4.9 5.2 5.5 VIN(V) <Measurement Data> Efficiency in the range of VIN = 2.8 to 5.5 V 35 100 30 90 25 80 20 70 IIOUT F Efficiency 15 60 10 50 2.8 3.1 3.4 3.7 4 4.3 VIN(V) 4.6 4.9 5.2 2 LEDs 3 LEDs 4 LEDs 5 LEDs 6 LEDs Efficiency(%) IF (mA) IOUT(mA) Input Voltage - Efficiency/Output Current 4LED Drive, L=6.8H Efficiency (%) Average Efficiency (%) 82.60 to 88.46 82.69 to 87.78 80.73 to 86.22 80.73 to 87.28 79.78 to 85.55 86.29 85.95 83.05 83.45 81.15 Output current in the range of VIN = 3.0 to 5.0 V (VIN = 3.6 V typ.) 5.5 Output Current (mA) VIN = 3.6 V 2 LEDs 3 LEDs 4 LEDs 5 LEDs 6 LEDs 21.13 20.60 20.87 20.06 19.90 Tolerance (%) Min Max -3.50 -1.95 -1.75 -1.81 -1.95 1.77 1.38 1.11 1.15 1.28 Note: These application examples are provided for reference only. Thorough evaluation and testing should be implemented when designing your application's mass production design. 7 2006-06-14 TB62756FUG 2. Application Circuit Example and Measurement Data (reference data) VIN = 2.8 to 5.5 V L1 S-Di * Evaluation conditions (Ta = 25C) WLEDs 2 to 6 SW SHDN FB RSENS = 16 GND : 1001AS series (TOKO, INC) (Size: 3.6 mm x 3.6 mm x 1.2 mm) C1 : C2012JB1E225K (TDK Corp.) : C2012JB1E105K (TDK Corp.) C2 S-Di : CUS02 1 A/30 V (TOSHIBA Corp.) WLEDs : NSCW215T (NICHIA Corp.) L1 C2 = 1.0 F 100 35 100 30 90 30 90 25 80 25 80 20 70 IF IOUT Efficiency 15 10 2.8 3.1 3.4 3.7 4 4.3 VIN(V) 4.6 4.9 5.2 IF (mA) IOUT(mA) 35 70 20 60 15 50 10 5.5 IF IOUT Efficiency 3.1 3.4 3.7 4 4.3 VIN(V) 4.6 4.9 5.2 5.5 Input Voltage - Efficiency/Output Current 6LED Drive, L=10H 100 100 30 90 30 90 25 80 25 80 70 20 IOUT IF Efficiency Efficiency 10 2.8 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 IF (mA) IOUT(mA) 35 35 Efficiency(%) IF (mA) IOUT(mA) 60 50 2.8 Input Voltage - Efficiency/Output Current 3LED Drive, L=6.8H 15 Efficiency(%) Input Voltage - Efficiency/Output Current 5LED Drive, L=10H Efficiency(%) IF (mA) IOUT(mA) Input Voltage - Efficiency/Output Current 2LED Drive, L=4.7H 60 15 50 10 5.5 70 20 IOUT IF Efficiency Efficiency Efficiency(%) C1 = 2.2 F VIN 60 50 2.8 3.1 3.4 3.7 4 4.3 VIN(V) VIN(V) 4.6 4.9 5.2 5.5 <Measurement Data> Efficiency in the range of VIN = 2.8 to 5.5 V 35 100 30 90 25 80 20 70 IF IOUT Efficiency 15 60 50 10 2.8 3.1 3.4 3.7 4 4.3 VIN(V) 4.6 4.9 5.2 2 LEDs 3 LEDs 4 LEDs 5 LEDs 6 LEDs Efficiency(%) IF (mA) IOUT(mA) Input Voltage - Efficiency/Output Current 4LED Drive, L=6.8H Efficiency (%) Average Efficiency (%) 83.10 to 88.60 81.32 to 86.47 79.15 to 84.63 79.72 to 86.39 78.91 to 85.10 86.55 84.54 81.30 82.87 80.47 Output current in the range of VIN = 3.0 to 5.0 V (VIN = 3.6 V typ.) 5.5 Output Current (mA) VIN = 3.6 V 2 LEDs 3 LEDs 4 LEDs 5 LEDs 6 LEDs 21.17 20.85 20.56 20.10 19.95 Tolerance (%) Min Max -3.32 -1.95 -1.79 -1.82 -1.94 1.73 1.38 1.15 1.22 1.26 Note: These application examples are provided for reference only. Thorough evaluation and testing should be implemented when designing your application's mass production design. 8 2006-06-14 TB62756FUG 3. Application Circuit Example and Measurement Data (reference data) VIN = 2.8 to 5.5 V L1 S-Di * Evaluation conditions (Ta = 25C) WLEDs 2 to 6 SW SHDN FB RSENS = 16 GND : LQH2M series (Murata Manufacturing Co.,Ltd.) (Size: 2.0 mm x 1.6 mm x 0.95 mm) : C2012JB1E105K (TDK Corp.) C1 C2 : C2012JB1E105K (TDK Corp.) S-Di : CUS02 1 A/30 V (TOSHIBA Corp.) WLEDs : NSCW215T (NICHIA Corp.) L1 C2 = 1.0 F 100 35 100 30 90 30 90 25 80 25 80 20 70 IOUT IF Efficiency Efficiency 15 10 2.8 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 IF (mA) IOUT(mA) 35 60 15 50 10 5.5 70 20 IF IOUT Efficiency Efficiency 3.1 3.4 3.7 4 4.3 VIN(V) 100 30 90 25 80 70 20 IIOUT F Efficiency 10 3.4 3.7 4 4.3 4.6 4.9 5.2 IF (mA) IOUT(mA) 35 3.1 4.6 4.9 5.2 5.5 Input Voltage - Efficiency/Output Current 6LED Drive, L=10H Efficiency(%) IF (mA) IOUT(mA) Input Voltage - Efficiency/Output Current 3LED Drive, L=6.8H 2.8 60 50 2.8 VIN(V) 15 Efficiency(%) Input Voltage - Efficiency/Output Current 5LED Drive, L=10H Efficiency(%) IOUT(mA) IF (mA) Input Voltage - Efficiency/Output Current 2LED Drive, L=4.7H 35 100 30 90 25 80 60 15 50 10 5.5 70 20 IOUT IF Efficiency Efficiency Efficiency(%) C1 = 2.2 F VIN 60 50 2.8 3.1 3.4 3.7 4 4.3 VIN(V) VIN(V) 4.6 4.9 5.2 5.5 <Measurement Data> Efficiency in the range of VIN = 2.8 to 5.5 V 35 100 30 90 25 80 20 70 IOUT IF Efficiency Efficiency 15 60 50 10 2.8 3.1 3.4 3.7 4 4.3 VIN(V) 4.6 4.9 5.2 2 LEDs 3 LEDs 4 LEDs 5 LEDs 6 LEDs Efficiency(%) IF (mA) IOUT(mA) Input Voltage - Efficiency/Output Current 4LED Drive, L=6.8H Efficiency (%) Average Efficiency (%) 82.37 to 88.70 80.19 to 86.55 78.11 to 84.54 74.79 to 84.94 74.14 to 83.47 86.38 84.12 80.16 79.94 77.17 Output current in the range of VIN = 3.0 to 5.0 V (VIN = 3.6 V typ.) 5.5 Output Current (mA) VIN = 3.6 V 2 LEDs 3 LEDs 4 LEDs 5 LEDs 6 LEDs 21.19 20.90 20.63 20.09 19.93 Tolerance (%) Min Max -3.26 -1.87 -1.78 -1.88 -1.99 1.69 2.17 1.01 1.25 1.07 Note: These application examples are provided for reference only. Thorough evaluation and testing should be implemented when designing your application's mass production design. 9 2006-06-14 TB62756FUG 4. Application Circuit Example and Measurement Data (reference data) VIN = 2.8 to 5.5 V L1 S-Di * Evaluation conditions (Ta = 25C) WLEDs 2 to 6 SW SHDN FB RSENS = 16 GND : VLF3010A series (TDK Corp.) (Size: 3.0 mm x 3.0 mm x 1.0 mm) C1 : C2012JB1E225K (TDK Corp.) : C2012JB1E105K (TDK Corp.) C2 S-Di : CUS02 1 A/30 V (TOSHIBA Corp.) WLEDs : NSCW215T (NICHIA Corp.) L1 C2 = 1.0 F Input Voltage - Efficiency/Output Current 2LED Drive, L=4.7H 30 90 25 80 20 70 IOUT IF Efficiency Efficiency 15 10 2.8 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 IF (mA) IOUT(mA) 100 Efficiency(%) IF (mA) IOUT(mA) 35 35 100 30 90 25 80 70 20 60 15 50 10 5.5 IF IOUT Efficiency Efficiency 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 5.5 VIN(V) Input Voltage - Efficiency/Output Current 3LED Drive, L=6.8H Input Voltage - Efficiency/Output Current 6LED Drive, L=10H 100 35 100 30 90 30 90 25 80 25 80 70 20 IF IOUT Efficiency Efficiency 15 10 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 IF (mA) IOUT(mA) 35 Efficiency(%) IF (mA) IOUT(mA) 60 50 2.8 VIN(V) 2.8 Efficiency(%) Input Voltage - Efficiency/Output Current 5LED Drive, L=10H 70 20 60 15 50 10 5.5 IOUT IF Efficiency Efficiency Efficiency(%) C1 = 2.2 F VIN 60 50 2.8 3.1 3.4 3.7 4 VIN(V) 4.3 4.6 4.9 5.2 5.5 VIN(V) <Measurement Data> Efficiency in the range of VIN = 2.8 to 5.5 V 35 100 30 90 25 80 70 20 IIOUT F Efficiency 15 60 50 10 2.8 3.1 3.4 3.7 4 4.3 4.6 4.9 5.2 2 LEDs 3 LEDs 4 LEDs 5 LEDs 6 LEDs Efficiency(%) IF (mA) IOUT(mA) Input Voltage - Efficiency/Output Current 4LED Drive, L=6.8H Efficiency (%) Average Efficiency (%) 79.85 to 86.97 80.19 to 85.32 78.77 to 83.60 79.72 to 86.39 78.91 to 85.10 84.02 83.39 80.69 82.87 80.49 Output current in the range of VIN = 3.0 to 5.0 V (VIN = 3.6 V typ.) 5.5 Output Current (mA) VIN = 3.6 V VIN(V) 2 LEDs 3 LEDs 4 LEDs 5 LEDs 6 LEDs 21.19 20.89 20.64 20.10 19.95 Tolerance (%) Min Max -3.08 -1.86 -1.68 -1.82 -1.94 1.67 1.33 1.11 1.22 1.26 Note: These application examples are provided for reference only. Thorough evaluation and testing should be implemented when designing your application's mass production design. 10 2006-06-14 TB62756FUG 5. Application Circuit Example and Measurement Data (reference data) VIN = 2.8 to 5.5 V L1 S-Di * Evaluation conditions (Ta = 25C) WLEDs 2 to 4 SW SHDN FB RSENS = 16 GND : 32R51 (KOA Corp.) (Size: 3.2 mm x 2.5 mm x 0.6 mm) C1 : C2012JB1E225K (TDK Corp.) : C2012JB1E105K (TDK Corp.) C2 S-Di : CUS02 1 A/30 V (TOSHIBA Corp.) WLEDs : NSCW215T (NICHIA Corp.) L1 C2 = 1.0 F 100 30 90 25 80 70 20 Iout IF Efficiency Efficiency 15 60 IF (mA) 35 Output Current (mA) Input Voltage - Efficiency/Output Current 3LED Drive, L=5.1H Efficiency(%) IF (mA) Output Current (mA) Input Voltage - Efficiency/Output Current 2LED Drive, L=5.1H 2.8 3.1 3.4 3.7 4 4.3 VIN(V) 4.6 4.9 5.2 100 30 90 25 80 20 70 IIout F Efficiency Efficiency 15 60 10 50 10 35 50 2.8 5.5 Efficiency(%) C1 = 2.2 F VIN 3.1 3.4 3.7 4 4.3 VIN(V) 4.6 4.9 5.2 5.5 <Measurement Data> Efficiency in the range of VIN = 2.8 to 5.5 V 35 100 30 90 25 80 70 20 IIout F Efficiency Efficiency 15 60 Efficiency(%) IF (mA) Output Current (mA) Input Voltage - Efficiency/Output Current 4LED Drive, L=5.1H 2 LEDs 3 LEDs 4 LEDs 2.8 3.1 3.4 3.7 4 4.3 VIN(V) 4.6 4.9 5.2 Average Efficiency (%) 86.73 83.52 80.78 Output current in the range of VIN = 3.0 to 5.0 V (VIN = 3.6 V typ.) Output Current (mA) VIN = 3.6 V 50 10 Efficiency (%) 83.08 to 89.23 79.02 to 86.30 75.75 to 83.83 5.5 2 LEDs 3 LEDs 4 LEDs 21.06 20.57 20.22 Tolerance (%) Min Max -2.46 -2.39 -2.28 4.02 2.94 2.65 Note: These application examples are provided for reference only. Thorough evaluation and testing should be implemented when designing your application's mass production design. 11 2006-06-14 TB62756FUG Package Dimensions Weight: 0.016 g (typ.) 12 2006-06-14 TB62756FUG Notes on Contents 1. Block Diagrams Some of the functional blocks, circuits, or constants in the block diagram may be omitted or simplified for explanatory purposes. 2. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 3. Timing Charts Timing charts may be simplified for explanatory purposes. 4. Application Circuits The application circuits shown in this document are provided for reference purposes only. Thorough evaluation is required, especially at the mass production design stage. Toshiba does not grant any license to any industrial property rights by providing these examples of application circuits. 5. Test Circuits Components in the test circuits are used only to obtain and confirm the device characteristics. These components and circuits are not guaranteed to prevent malfunction or failure from occurring in the application equipment. IC Usage Considerations Notes on Handling of ICs (1) The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. (2) Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. (3) If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. (4) Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. 13 2006-06-14 TB62756FUG (5) Carefully select external components (such as inputs and negative feedback capacitors) and load components (such as speakers), for example, power amp and regulator. If there is a large amount of leakage current such as input or negative feedback condenser, the IC output DC voltage will increase. If this output voltage is connected to a speaker with low input withstand voltage, overcurrent or IC failure can cause smoke or ignition. (The over current can cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output DC voltage to a speaker directly. 14 2006-06-14 TB62756FUG Points to Remember on Handling of ICs (1) Heat Radiation Design In using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. (2) Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the motor's power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device's motor power supply and output pins might be exposed to conditions beyond absolute maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 15 2006-06-14 TB62756FUG About solderability, following conditions were confirmed * Solderability (1) Use of Sn-37Pb solder Bath * solder bath temperature = 230C * dipping time = 5 seconds * the number of times = once * use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath * solder bath temperature = 245C * dipping time = 5 seconds * the number of times = once * use of R-type flux RESTRICTIONS ON PRODUCT USE 060116EBA * The information contained herein is subject to change without notice. 021023_D * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc. 021023_A * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. 021023_B * The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 060106_Q * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 021023_C * The products described in this document are subject to the foreign exchange and foreign trade laws. 021023_E 16 2006-06-14