CONTACTS
Arrangement SPDT (1 Form C)
SPST (1 Form A)
Ratings Resistive load:
Max. switched power: 480 W or 4432 VA
Max. switched current: 16 A
Max. switched voltage: 150* VDC or 440 VAC
*Note: If switching voltage is greater than 30VDC,
special precautions must be taken. Please contact the
factory.
Rated Load 16 A at 277 VAC general use, 100k
UL, CUR cycles 105°C (10A sensitive coil)
VDE 16 A at 250 VAC resistive, 105°C
(10A sensitive coil)
6 A at 400 VAC resistive, 105°C
Material Silver nickel. Gold plating available
Resistance < 50 milliohms initially (using 6 V 1 A method)
GENERAL DATA
Life Expectancy Minimum operations
Mechanical 1 x 107
Electrical 1 x 105at 16 A 277 VAC general use
OperateTime (typical) 7 ms at nominal coil voltage
ReleaseTime (typical) 3 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength 5000 Vrms coil to contact
(at sea level for1min.) 1000 Vrms between open contacts
Insulation 1000 megohms min. at 20°C
Resistance 500 VDC 50% RH
Dropout Greater than 10% of nominal coil voltage
Ambient Temperature At nominal coil voltage
Operating -40°C (-40°F) to 105°C (221°F)
Storage -40°C (-40°F) to 130°C (266°F)
Vibration 0.062" DA at 10–55 Hz
Shock 10 g
Enclosure P.B.T. polyester
Terminals Tinned copper alloy, P.C.
Max. Solder Temp. 270°C (518°F)
Max. Solder Time 5 seconds
Max. Solvent Temp. 80°C (176°F)
Max. Immersion Time 30 seconds
Weight 14 grams
AZAZ762H
16 A SPDT MINIATURE HIGH
TEMPERATURE POWER RELAY
FEATURES
•High ambient operating temperature (105°C)
•Dielectric strength 5000 Vrms
•Low cost
•Epoxy sealed versions available
•16 Amp switching (standard coil only)
•Class B (130°C) standard
•Isolation spacing greater than 10 mm
•UL, CUR file E44211, VDE40006031
COIL
Power
At Pickup Voltage 196 mW Standard
(typical) 141 mW Sensitive
Max. Continuous
Dissipation 1.7 W at 20°C (68°F) ambient
Temperature Rise 26°C (47°F) at nominal coil voltage
Max. Temperature 130°C (266°F)
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
11/13/08W
RELAY ORDERING DATA
COIL SPECIFICATIONS - STANDARD RELAYS ORDER NUMBER*
Nominal Coil Must Operate Max. Continuous Coil Unsealed Sealed
VDC VDC VDC Resistance ±10%
5 3.5 10.2 62 AZ762H–1CB–5D AZ762H–1CB–5DE
6 4.2 12.3 90 AZ762H–1CB–6D AZ762H–1CB–6DE
9 6.3 18.5 202 AZ762H–1CB–5D AZ762H–1CB–19DE
12 8.4 24.7 360 AZ762H–1CB–12D AZ762H–1CB–12DE
18 12.6 37.0 810 AZ762H–1CB–18D AZ762H–1CB–18DE
24 16.8 49.4 1440 AZ762H–1CB–24D AZ762H–1CB–24DE
48 33.6 98.0 5760 AZ762H–1CB–48D AZ762H–1CB–48DE
60 42.0 112.9 7500 AZ762H–1CB–60D AZ762H–1CB–60DE
COIL SPECIFICATIONS - SENSITIVE RELAYS ORDER NUMBER*
Nominal Coil Must Operate Max. Continuous Coil Unsealed Sealed
VDC VDC VDC Resistance ± 10%
5 3.75 10.2 100 AZ762H–1CB–5DS AZ762H–1CB–5DSE
6 4.50 12.3 144 AZ762H–1CB–6DS AZ762H–1CB–6DSE
9 6.75 18.5 324 AZ762H–1CB–9DS AZ762H–1CB–9DSE
12 9.0 24.7 576 AZ762H–1CB–12DS AZ762H–1CB–12DSE
18 13.5 37.0 1296 AZ762H–1CB–18DS AZ762H–1CB–18DSE
24 18.0 49.4 2304 AZ762H–1CB–24DS AZ762H–1CB–24DSE
48 36.0 98.0 9216 AZ762H–1CB–48DS AZ762H–1CB–48DSE
60 45.0 112.9 12857 AZ762H–1CB–60DS AZ762H–1CB–60DSE
AZ
11/13/08W
AZ762H
* For 1 form A contacts substitute “-1AB” for “-1CB.” For gold plated contacts add suffix “A.”
AZ762H
11/13/08W
[5 .0 ]
.1 9 7
[5 .0 ]
.1 9 7
VIEW ED TOW ARDS TERM INALS
PC BOARD LAYOUT
[15.16]
.597
[2 .5 ]
.0 9 8
[ø0 .8 ]
2X ø.0 3 2
[ø1.3]
[2 .5 ]
.0 9 8
.1 9 7
[5 .0 ]
.1 9 7
[5 .0 ]
[15.16]
[7 .5 ]
[15.7]
.1 5 4
6 X .0 3 5
[3 .9 ]
[0 .9 ]
.619 Max.
[7 .5 ]
6X ø.0 5 0
6X .020
[0 .5 ]
.0 9 8
[2 .5 ]
.597
.5 2 0 M a x .
[1 3 .2 ]
1.161 M ax.
[2 9 .5 ]
.2 9 5
.2 9 5
[7 .5 ]
2X ø.0 2 4
[ø0 .6 ]
.2 9 5
WIRING DIAGRAMS
VIEWED TOWARDS TERMINALS
2
1
3
6
4
7
5
8
.5 0 0
(1 2 .7 )
1.22
(3 0 .9 )
1.28
(3 2 .5 )
.1 7 7
(4 .5 )
MAX
.3 5 4
(9 .0 )
.3 6 6
(9 .3 )
.1 2 5 D IA
(0 .5 )
.1 9 7
(5 .0 )
.2 9 5
(7 .5 )
.590 (15)
.1 9 7
(5 .0 )
.0 5 9 D IA
(1 .5 )
.118
(3 .0 )
.4 1 4
(1 0 .5 )
HARDWARE
RETAINING CLIP
Viewed toward terminals
.661 [16.79]
1.385 [35.19]
.895 [22.73]
**
**
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
MECHANICAL DATA
ST484-U1
ST482-3
* Terminals 3 & 6 not used on form A
HARDWARE ORDERING DATA
DESCRIPTION ORDER NUMBER DESCRIPTION ORDER NUMBER
Socket ST484–U1 Retainer ST482–3
