ISDN S-INTERFACE MODULES Surface Mount, Dual, 1500 Vrms RoHS peak reflow temperature rating 245C Meets the pulse waveform template of CCITT I.430 when recommended transformer and chip pair are used Developed for enhanced EMC performance Excellent longitudinal balance Low- or high-frequency choke options available Electrical Specifications @ 25C -- Operating Temperature 0C to 70C RoHS Compliant Part Number T5049NL OCL Pri LL Sec (mH MIN) (H MAX) Ratio ( 2%) CW/W (pF MAX) CD Pri (pF MAX) DCR Pri ( +25% MAX) DCR Sec ( +25% MAX) D IDC (mA MAX) 3.4 3.4 4.7 mH Transformers 1CT:1CT 30 10 150 100 Isolation Voltage (Vrms MIN) IDC (mA MAX) Secondary Pins 3 20-18, 13-11 Chokes 1.4 NOTE: When ordering Tape & Reel packaging, add a "T" suffix to the part number (ex: T5049NLT). Mechanical Schematic T5049NL Weight . . . . . . . . . . . . . 6.94 grams Tape & Reel . . . . . . . . . . . .250/reel Tube . . . . . . . . . . . . . . . . . . 15/tube Dimensions: Inches mm Unless otherwise specified, all tolerances are .010 0,25 USA 858 674 8100 Germany www.pulseeng.com 49 7032 7806 0 Singapore 65 6287 8998 Shanghai 1 86 21 62787060 China 86 755 33966678 Taiwan 886 3 4356768 T635.D (10/10) ISDN S-INTERFACE MODULES Surface Mount, Dual, 1500 Vrms Module Selection Guide IC Manufacturer IC Part Number Pulse Part Number PEB2080/ 2081/ 2084/2085/2086 PSB 2186 Siemens T5049NL PSB 21381/ 21382/ 21383/ 21384 Definition of Terms Ratio: OCL: LL Sec: CW/W: CD Pri: This is the turns ratio, expressed as "Primary:Secondary". The term "CT" designates a center-tapped winding. Open Circuit Inductance, measured 20 kHz, 100 mV. Leakage Inductance measured across the primary with the respective secondary winding short-circuited. Winding capacitance, formed by the primary and secondary wire. These wires form the "Plates" of this capacitor. Measured at 100 kHz, 20 mV. This is the distributed capacitance. DCR: This is the resistance of the windings when measured in DC conditions. IDC: The maximum specified unbalanced DC current capability of the device. The minimum primary inductance and the maximum distributed capacitance satisfy the transmitter output and receiver input impedance requirements of CCITT I.430 for both TE and NT. The maximum distributed capacitance allows sufficient margin for the capacitance of the IC and a protection diode network. It is consistent with the overall maximum value specified and permitted length of the basic access TE cord. Flammability - Materials used in the products are recognized UL94-VO. Products meet the requirements of IEC 695-2-2 (needle flame test). USA 858 674 8100 Germany www.pulseeng.com 49 7032 7806 0 Singapore 65 6287 8998 Shanghai 2 86 21 62787060 China 86 755 33966678 Taiwan 886 3 4356768 T635.D (10/10) ISDN S-INTERFACE MODULES Surface Mount, Dual, 1500 Vrms Application Notes The S-Interface is the standardized four wire digital telephone access point defined by the CCITT I-Series recommendations for the Integrated Service Digital Network. This "basic rate access" accommodates two 64 Kbps "B-channels" for information, one 16 Kbps "D-channel" intended for signaling and control, and 48 Kbps for framing and other purposes, giving a total rate of 192 Kbps. The CCITT physical layer recommends that the user network interface be transformer coupled as shown in our typical application notes. Typical S-Interface Application Circuit for Motorola MC145574 *NOTE: Refer to Silicon Vendors' Application Notes for more details on power supply connection and specific component values. Common Mode Choke Performance 0 -10 HP-4195A CH1 CH2 Typical Common Mode Attenuation for the high-frequency Common Mode Choke (470 H) based on a 50 system. COMMON MODE ATTENUATION (dB) -20 XFMR -30 100:50 BALUN 50:100 BALUN -40 -50 -60 -70 -80 -90 -100 30 kHz 100 kHz 1 MHz 10 MHz 100 MHz FREQUENCY USA 858 674 8100 Germany www.pulseeng.com 49 7032 7806 0 Singapore 65 6287 8998 Shanghai 3 86 21 62787060 China 86 755 33966678 Taiwan 886 3 4356768 T635.D (10/10) ISDN S-INTERFACE MODULES Surface Mount, Dual, 1500 Vrms Common Mode Choke Performance (continued) -0 -10 HP-4195A CH1 CH2 COMMON MODE ATTENUATION (dB) -20 Typical Common Mode Attenuation for the low-frequency Common Mode Choke (4.7 mH), based on a 50 system. XFMR -30 50:100 BALUN 100:50 BALUN -40 -50 -60 -70 -80 -90 -100 30 kHz 100 kHz 1 MHz 10 MHz FREQUENCY For More Information: Pulse Worldwide Headquarters 12220 World Trade Dr. San Diego, CA 92128 U.S.A. www.pulseeng.com Tel: 858 674 8100 Fax: 858 674 8262 Pulse Europe Pulse China Headquarters Pulse North China Pulse South Asia Pulse North Asia Einsteinstrasse 1 D-71083 Herrenberg Germany B402, Shenzhen Academy of Aerospace Technology Bldg. 10th Kejinan Rd. High-Tech Zone Nanshan District Shenzen, PR China 518057 Tel: 86 755 33966678 Fax: 86 755 33966700 Room 2704/2705 Super Ocean Finance Ctr. 2067 Yan An Rd. West Shanghai 200336 China 135 Joo Seng Rd. #03-02 PM Industrial Bld g. Singapore 368363 Tel: 86 21 62787060 Fax: 86 2162786973 Tel: 65 6287 8998 Fax: 65 6287 8998 3F, No. 198 Zhongyuan Rd. Zhongli City Taoyuan County 320 Taiwan R. O. C. Tel: 886 3 4356768 Fax: 886 3 4356823 (Pulse) Fax: 886 3 4356820 (FRE) Tel: 49 7032 7806 0 Fax: 49 7032 7806 135 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. (c) Copyright, 2010. Pulse Engineering, Inc. All rights reserved. www.pulseeng.com 4 T635.D (10/10)