VCC GND
0.1 µF
5.0 V
RI+
RI-
RO
DO+
DO-
DI
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
DS8921
,
DS8921A
,
DS8921AT
SNLS374D –MAY 1998–REVISED JANUARY 2015
DS8921x Differential Line Driver and Receiver Pair
1 Features 3 Description
The DS8921, DS8921A, and DS8921AT devices are
1• 12-ns Typical Propagation Delay differential line driver and receiver pairs designed
• Output Skew: 0.5 ns Typical specifically for applications meeting the ST506,
• Meets the Requirements of EIA Standard RS-422 ST412, and ESDI disk drive standards. In addition,
these devices meet the requirements of the EIA
• Complementary Driver Outputs standard RS-422.
• High Differential or Common-Mode Input Voltage
Ranges of ±7 V The DS8921x receivers offer an input sensitivity of
200 mV over a ±7 V common mode operating range.
• ±0.2 V Receiver Sensitivity Over the Input Voltage Hysteresis is incorporated (typically 70 mV) to
Range improve noise margin for slowly changing input
• Receiver Input Hysteresis: 70 mV Typical waveforms.
• DS8921AT Industrial Temperature Operation: The DS8921x drivers are designed to provide
(−40°C to +85°C) unipolar differential drive to twisted-pair or parallel
wire transmission lines. Complementary outputs are
2 Applications logically ANDed and provide an output skew of 0.5 ns
(typical) with propagation delays of 12 ns.
• Differential Line Driver and Receiver for:
– ST506 Disk Drive Standard The DS8921x devices are designed to be compatible
with TTL and CMOS.
– ST412 Disk Drive Standard
– ESDI Disk Drive Standard Device Information(1)
– RS-422 Interface PART NUMBER PACKAGE BODY SIZE (NOM)
DS8921 SOIC (8) 4.90 mm x 3.91 mm
DS8921A PDIP (8) 9.81 mm x 6.35 mm
DS8921AT
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
SPACE Typical Application Block Diagram Simplified Functional Block Diagram
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DS8921
,
DS8921A
,
DS8921AT
SNLS374D –MAY 1998–REVISED JANUARY 2015
www.ti.com
Table of Contents
8.1 Overview................................................................... 8
1 Features.................................................................. 18.2 Functional Block Diagram......................................... 8
2 Applications ........................................................... 18.3 Feature Description................................................... 8
3 Description............................................................. 18.4 Device Functional Modes.......................................... 8
4 Revision History..................................................... 29 Application and Implementation .......................... 9
5 Pin Configuration and Functions......................... 39.1 Application Information.............................................. 9
6 Specifications......................................................... 39.2 Typical Application.................................................... 9
6.1 Absolute Maximum Ratings ...................................... 310 Power Supply Recommendations ..................... 12
6.2 ESD Ratings.............................................................. 411 Layout................................................................... 12
6.3 Recommended Operating Conditions....................... 411.1 Layout Guidelines ................................................. 12
6.4 Electrical Characteristics........................................... 411.2 Layout Example .................................................... 12
6.5 Receiver Switching Characteristics .......................... 512 Device and Documentation Support................. 13
6.6 Driver Switching Characteristics: Single-Ended
Characteristics ........................................................... 512.1 Related Links ........................................................ 13
6.7 Driver Switching Characteristics: Differential 12.2 Trademarks........................................................... 13
Characteristics ........................................................... 512.3 Electrostatic Discharge Caution............................ 13
6.8 Typical Characteristics.............................................. 612.4 Glossary................................................................ 13
7 Parameter Measurement Information .................. 613 Mechanical, Packaging, and Orderable
7.1 AC Test Circuits and Switching Diagrams................ 6Information ........................................................... 13
8 Detailed Description.............................................. 8
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (April 2013) to Revision D Page
• Added ESD Ratings table, Feature Description section, Device Functional Modes,Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section ................................................................................................. 1
Changes from Revision B (November 2004) to Revision C Page
• Changed layout of National Data Sheet to TI format. ........................................................................................................... 1
2Submit Documentation Feedback Copyright © 1998–2015, Texas Instruments Incorporated
Product Folder Links: DS8921 DS8921A DS8921AT
DS8921
,
DS8921A
,
DS8921AT
www.ti.com
SNLS374D –MAY 1998–REVISED JANUARY 2015
5 Pin Configuration and Functions
D, P Package
8 Pins
Top View
Pin Functions
PIN I/O DESCRIPTION
NAME NO.
DIFFERENTIAL SIGNALING I/O
DI 3 I TTL/CMOS Compatible Driver Input
DO+, DO– 6, 5 O Inverting and non-inverting differential driver outputs
RI+, RI– 8, 7 I Inverting and non-inverting differential receiver inputs
RO 2 O Receiver Output Pin
POWER
GND 4 Power Ground Pin
VCC 1 Power Supply pin, provide 5-V supply
6 Specifications
6.1 Absolute Maximum Ratings(1)(2)
MIN MAX UNIT
Supply Voltage 7 V
Driver Input Voltage −0.5 7 V
Output Voltage 5.5 V
Receiver Output Sink Current 50 mA
Receiver Input Voltage –10 10 V
Differential Input Voltage –12 12 V
Maximum Package Power Dissipation at 25°C: D Package 730 mW
Maximum Package Power Dissipation at 25°C: P Package 1160 mW
Derate D Package, above 25°C 9.3 mW/°C
Derate P Package, above 25°C 5.8 mW/°C
Lead Temperature 260 °C
(Soldering, 4 sec.) 260 °C
Maximum Junction Temperature 150 °C
Storage Temperature, Tstg −65 165 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instrument Sales Office/ Distributors for availability and
specifications.
Copyright © 1998–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: DS8921 DS8921A DS8921AT
DS8921
,
DS8921A
,
DS8921AT
SNLS374D –MAY 1998–REVISED JANUARY 2015
www.ti.com
6.2 ESD Ratings VALUE UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000
V(ESD) Electrostatic discharge V
Charged-device model (CDM), per JEDEC specification JESD22- ±1500
C101(2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions MIN MAX UNIT
Supply Voltage 4.5 5.5 V
Temperature (TA): DS8921/DS8921A 0 70 °C
Temperature (TA): DS8921AT −40 85 °C
6.4 Electrical Characteristics
Over operating free-air temperature range unless otherwise noted.(1)(2)(3)
TEST CONDITIONS MIN TYP MAX UNIT
RECEIVER
VTH −7 V ≤VCM ≤+7 V −200 ±35 +200 mV
VHYST −7 V ≤VCM ≤+7 V 15 70 mV
RIN VIN =−7 V, +7 V, (Other Input = GND) 4.0 6.0 kΩ
VIN = 10 V 3.25 mA
IIN VIN =−10 V −3.25 mA
VOH IOH =−400 μA 2.5 V
VOL IOL = 8 mA 0.5 V
ISC VCC = MAX, VOUT = 0 V −15 −100 mA
DRIVER
VIH 2.0 V
VIL 0.8 V
IIL VCC = MAX, VIN = 0.4 V −40 −200 μA
IIH VCC = MAX, VIN = 2.7 V 20 μA
IIVCC = MAX, VIN = 7.0 V 100 μA
VCL VCC = MIN, IIN =−18 mA −1.5 V
VOH VCC = MIN, IOH =−20 mA 2.5 V
VOL VCC = MIN, IOL = +20 mA 0.5 V
IOFF VCC = 0V, V OUT = 5.5 V 100 μA
|VT| – |VT| 0.4 V
VT2.0 V
|VOS – VOS| 0.4 V
ISC VCC = MAX, VOUT = 0 V −30 −150 mA
DRIVER AND RECEIVER
ICC VCC = MAX, VOUT = Logic 0 35 mA
(1) All currents into device pins are shown as positive values; all currents out of the device are shown as negative; all voltages are
referenced to ground unless otherwise specified. All values shown as max or min are classified on absolute value basis.
(2) All typical values are VCC = 5 V, TA= 25°C.
(3) Only one output at a time should be shorted.
4Submit Documentation Feedback Copyright © 1998–2015, Texas Instruments Incorporated
Product Folder Links: DS8921 DS8921A DS8921AT
results assume a linear transition between measurement points and are a result of the following equations: Where:
DS8921
,
DS8921A
,
DS8921AT
www.ti.com
SNLS374D –MAY 1998–REVISED JANUARY 2015
6.5 Receiver Switching Characteristics MAX MAX MAX
TEST CONDITIONS MIN TYP UNIT
8921 8921A 8921AT
tpLH CL= 30 pF 14 22.5 20 20 ns
(Figure 3 and Figure 4)
tpHL CL= 30 pF 14 22.5 20 20 ns
(Figure 3 and Figure 4)
|tpLH–t pHL| CL= 30 pF 0.5 5 3.5 5 ns
(Figure 3 and Figure 4)
6.6 Driver Switching Characteristics: Single-Ended Characteristics
MAX MAX MAX
TEST CONDITIONS MIN TYP UNIT
8921 8921A 8921AT
tpLH CL= 30 pF 10 15 15 15 ns
(Figure 5 and Figure 6)
tpHL CL= 30 pF 10 15 15 15 ns
(Figure 5 and Figure 6)
tTLH CL= 30 pF 5 8 8 9.5 ns
(Figure 9 and Figure 10)
tTHL CL= 30 pF 5 8 8 9.5 ns
(Figure 9 and Figure 10)
Skew CL = 30 pF(1) 1 5 3.5 3.5 ns
(Figure 5 and Figure 6)
(1) Difference between complementary outputs at the 50% point.
6.7 Driver Switching Characteristics: Differential Characteristics(1)
MAX MAX MAX
TEST CONDITIONS MIN TYP UNIT
8921 8921A 8921AT
tpLH CL= 30 pF 10 15 15 15 ns
(Figure 5,Figure 7, and Figure 8)
tpHL CL= 30 pF 10 15 15 15 ns
(Figure 5,Figure 7, and Figure 8)
|tpLH–t pHL| CL= 30 pF 0.5 6 2.75 2.75 ns
(Figure 5,Figure 7, and Figure 8)
(1) Differential Delays are defined as calculated results from single ended rise and fall time measurements. This approach in establishing
AC performance specifications has been taken due to limitations of available Automatic Test Equipment (ATE). The calculated ATE
Tcr = Crossing Point Tra, Trb, Tfa and T fb are time measurements with respect to the input. See Figure 8.
Copyright © 1998–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: DS8921 DS8921A DS8921AT
NOTE:R1= 100 Ohms, C1 = C2 = C3 = 30 pF
R1
C1 C2
C3
D
4.4
4.6
4.8
5.0
5.2
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
Low to High Transition Time (ns)
Supply Voltage (V)
T(TLH)
C004
5.2
5.4
5.6
5.8
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
High to Low Transition Time (ns)
Supply Voltage (V)
T(THL)
C005
DS8921
,
DS8921A
,
DS8921AT
SNLS374D –MAY 1998–REVISED JANUARY 2015
www.ti.com
6.8 Typical Characteristics
Test Setup: Figure 5. Data Rate, Test Pattern: 2 Mbps, 1010 Pattern. T: 25°C
Figure 1. Typical Driver Output Low to High Transition Time Figure 2. Typical Driver Output High to Low Transition Time
vs Supply Voltage vs Supply Voltage
7 Parameter Measurement Information
7.1 AC Test Circuits and Switching Diagrams
Figure 3. Test Circuit for Receiver Output
Figure 4. Receiver Propagation Delay
Figure 5. Driver Test Circuit
6Submit Documentation Feedback Copyright © 1998–2015, Texas Instruments Incorporated
Product Folder Links: DS8921 DS8921A DS8921AT
DS8921
,
DS8921A
,
DS8921AT
www.ti.com
SNLS374D –MAY 1998–REVISED JANUARY 2015
AC Test Circuits and Switching Diagrams (continued)
Figure 6. Driver Single-Ended Propagation Delay
Figure 7. Driver Differential Propagation Delay
Figure 8. Driver Delay ATE Testing
Figure 9. Driver Output Transition Time
Figure 10. Driver Output Transition Time
Copyright © 1998–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: DS8921 DS8921A DS8921AT
VCC GND
0.1 µF
5.0 V
RI+
RI-
RO
DO+
DO-
DI
DS8921
,
DS8921A
,
DS8921AT
SNLS374D –MAY 1998–REVISED JANUARY 2015
www.ti.com
8 Detailed Description
8.1 Overview
The DS8921x devices are each a differential line driver and receiver pair in a single package. The devices are
designed specifically for ST506, ST412, and ESDI disk drive standards, as well as RS-422 interface applications.
The DS8921 and DS8921A are rated at a commercial temperature range of 0°C to 70°C, whereas the
DS8921AT is rated at an extended temperature range of -40°C to +85°C.
8.2 Functional Block Diagram
8.3 Feature Description
The DS8921x devices each contain a differential driver and receiver.
The driver converts a TTL or CMOS input to complementary outputs that provide differential drive to a twisted-
pair or parallel wire transmission line. The receiver converts the differential signals at its input pins to a TTL
output. The receiver offers an input sensitivity of ±200 mV and supports a common-mode input voltage of ±7 V.
8.4 Device Functional Modes
Table 1. Function Table
RECEIVER DRIVER
INPUT OUTPUT INPUT OUTPUT
RI+, RI- RO DI DO+ DO-
VID(1) ≥VTH (MAX) 1 1 1 0
VID(1) ≤VTH (MIN) 0 0 0 1
Open 1
(1) VID is the input differential voltage between RI+ and RI–.
8Submit Documentation Feedback Copyright © 1998–2015, Texas Instruments Incorporated
Product Folder Links: DS8921 DS8921A DS8921AT
DS8921
,
DS8921A
,
DS8921AT
www.ti.com
SNLS374D –MAY 1998–REVISED JANUARY 2015
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The DS8921 is a differential line driver and receiver pair in a single package, designed for applications for the
ST506, ST412, and ESDI Disk Drive Standards. The DS8921 is compatible to EIA RS-422 signaling standards,
supporting 200-mV input sensitivity across a ±7-V common mode operating range. This transceiver is intended
for driving differential signal across long transmission lines and translating received differential signals into their
CMOS/TTL single-ended equivalence. The DS8921 transmits and reproduces received data in communications
links where ground reference difference, or noisy environment are common.
9.2 Typical Application
Figure 11 shows a typical implementation of the DS8921x device in a ST506 and ST412 disk drive application.
The differential outputs of the driver are connected to a twisted-pair transmission line, carrying data from the
driver to the differential receiver at the other end of the cable. A differential termination resistor should be
connected across the input pins of the receiver.
Figure 11. ST506 and ST412 Application
Copyright © 1998–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: DS8921 DS8921A DS8921AT
Time (400 ns/DIV)
Data Signal (2 V/DIV)
0 V
Time (400 ns/DIV)
Data Signal (2 V/DIV)
0 V
DS8921
,
DS8921A
,
DS8921AT
SNLS374D –MAY 1998–REVISED JANUARY 2015
www.ti.com
Typical Application (continued)
9.2.1 Design Requirements
• Apply TTL or LVCMOS signal to driver input at DI
• Transmit complementary outputs at DO+ and DO-
• Receive complimentary input signals at RI+ and RI-
• Receive TTL output signal at RO
• Use controlled-impedance transmission lines such as printed circuit board traces, twisted-pair wires or parallel
wire cable
• Place terminating resistor at the far end of the differential pair
9.2.2 Detailed Design Procedure
• Connect VCC and GND pins to the power and ground planes of the printed circuit board, with 0.1-uF bypass
capacitor
• Use TTL/LVCMOS logic levels at DI and RO
• Use controlled-impedance transmission media for the differential signals DI+- and RO+-
• Place a terminating resistor at the far-end of the differential pair to avoid reflection
• Ensure the received complimentary signals at RO+ and RO- are within the signal threshold of ±200 mV
9.2.3 Application Curves
2.0 Mbps Single-Ended 1010 Data Pattern 2.0 Mbps Differential Data Pattern
Note: The input for the driver is Figure 12
Figure 12. Driver Single-Ended Input Signal Figure 13. Driver Differential Output Signal
10 Submit Documentation Feedback Copyright © 1998–2015, Texas Instruments Incorporated
Product Folder Links: DS8921 DS8921A DS8921AT
Time (400 ns/DIV)
Data Signal (2 V/DIV)
0 V
Time (400 ns/DIV)
Data Signal (2 V/DIV)
0 V
DS8921
,
DS8921A
,
DS8921AT
www.ti.com
SNLS374D –MAY 1998–REVISED JANUARY 2015
Typical Application (continued)
2.0 Mbps Differential Data Pattern 2.0 Mbps Single-Ended 1010 Data Pattern
Note: The input for the receiver is Figure 14
Figure 14. Receiver Differential Input Signal Figure 15. Receiver Single-Ended Output Signal
Copyright © 1998–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: DS8921 DS8921A DS8921AT
DS8921/DS8921A/DS8921AT
1
2
3
4
5
6
7
8
Via to VCC
Plane
Via to GND
Plane
Via to GND
Plane
RX Differential Pair
TX Differential Pair
Termination
Resistor
Bypass Capacitor
DS8921
,
DS8921A
,
DS8921AT
SNLS374D –MAY 1998–REVISED JANUARY 2015
www.ti.com
10 Power Supply Recommendations
TI recommends connecting the supply (VCC) and ground (GND) pins to power planes that are routed on
adjacent layers of the PCB. Additionally, careful attention should be paid to bypassing the supply using a
capacitor. A 0.1-µF bypass capacitor should be connected to the VCC pin such that the capacitor is as close as
possible to the device.
11 Layout
11.1 Layout Guidelines
High-speed interconnects should be treated as transmission lines with a controlled impedance. The differential
interconnect can be a pair of printed-circuit board (PCB) traces, twisted-pair wires, or a parallel wire cable. A
termination resistor should be placed at the differential input, and the resistor value should be approximately the
same as the differential impedance of the transmission line to minimize reflections.
It is preferable to connect the VCC and GND pins to the power and ground planes using plated-through-holes.
Additionally, a 0.1-µF bypass capacitor should be placed close to the VCC pin across VCC and GND.
Place a terminating resistor at the receiving end of the interconnect transmission line, as close as possible to the
input pins of the receiver. The terminating resistor value should be approximately the same as the differential pair
impedance to minimize reflection, and the transmission line should have a controlled impedance with minimum
impedance discontinuities.
The input and output differential signals of the device should have traces that are routed exclusively on one layer
of the board, and the differential pairs should also be routed away from other differential pairs in order to
minimize crosstalk between transmission lines. Additionally, the differential pairs should have a controlled
impedance with minimum impedance discontinuities and be terminated with a resistor that is closely matched to
the differential pair impedance in order to minimize transmission line reflections. The differential pairs should be
routed with uniform trace width and spacing to minimize impedance mismatch.
11.2 Layout Example
Figure 16. DS8921 Example Layout
12 Submit Documentation Feedback Copyright © 1998–2015, Texas Instruments Incorporated
Product Folder Links: DS8921 DS8921A DS8921AT
DS8921
,
DS8921A
,
DS8921AT
www.ti.com
SNLS374D –MAY 1998–REVISED JANUARY 2015
12 Device and Documentation Support
12.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 2. Related Links
TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY
DS8921 Click here Click here Click here Click here Click here
DS8921A Click here Click here Click here Click here Click here
DS8921AT Click here Click here Click here Click here Click here
12.2 Trademarks
All trademarks are the property of their respective owners.
12.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.4 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 1998–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: DS8921 DS8921A DS8921AT
PACKAGE OPTION ADDENDUM
www.ti.com 25-Aug-2018
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
DS8921AM/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS89
21AM
DS8921AMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS89
21AM
DS8921ATM OBSOLETE SOIC D 8 TBD Call TI Call TI -40 to 85 DS892
1ATM
DS8921ATM/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 DS892
1ATM
DS8921M/NOPB ACTIVE SOIC D 8 95 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS892
1M
DS8921MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS892
1M
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
PACKAGE OPTION ADDENDUM
www.ti.com 25-Aug-2018
Addendum-Page 2
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
DS8921AMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
DS8921MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 10-Aug-2016
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
DS8921AMX/NOPB SOIC D 8 2500 367.0 367.0 35.0
DS8921MX/NOPB SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 10-Aug-2016
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
