MNR14E0APF122 - ROHM Co., Ltd.

MNR14

Resistors

Rev.F 1/4

Comp act Chip Resistor Networks

MNR14 (0603×4 size)

zFeatures

1) Conve x electrodes

Easy to check the fillet after soldering is finished.

2) Small, light, rectangular 4-chip network

Area ratio is 65% smaller than that of MNR34, while weight ratio has been cut 75%.

3) High-density mounting

Can be mounted even more densely than four 0603 chips (MCR03), and mounting costs are lower .

4) Compatible with a wide ra nge of mounting equipment.

Squared coners make it excellent for mounting using image recognition machines.

5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certi fication.

Design a nd specificat ions are s ubject to chan ge without notice. Caref ully check the specificat ion sheet su pplied wit h

the product before using or ordering it.

zRatings

Item Conditions Specifications

0.063W (1 / 16W)

Rated power

Rated voltage

Operating temperature

Nominal resistance

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°

−55°C to +125°C

at 70°

Limiting element voltage 50V

The voltage rating is calculated by the following equation. If the value

obtained exceeds the limiting element voltage, the voltage rating

is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

R: Nominal resistance (Ω)

E= P×R

100

−55 0 70 100 125

AMBIENT TEMPERATURE (°

)

POWER LOAD (%)

Fig.1

See Table 1.

MNR14

Resistors

Rev.F 2/4

Resistance

Rated current

Operating temperature

Max. 50mΩ

−55°C to +125°C

Jumper type

Table 1

J (±5%) 2.2

≤

6.8 (E6)

2.2

≤

6.8 (E6)

±500

F (±1%) 10

≤

1M (E24) ±100

≤

1M (E24) ±200

Resistance tolerance Resistance range

(Ω)

Resistance temperature coefficient

(ppm / °

)

•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duratio n, high-level loads), be certain to evaluate the

component in the mo unted state. In addition, the reliability and performance of this component cannot be guaranteed if it i s used with a steady state v oltage that

is greater than its rated voltage.

zCharacteristics

Item Test conditions (JIS C 5201-1)

Resistor type

Guaranteed value

Jumper type

Resistance

Variation of resistance

with temperature

Solderability

Damp heat, steady state

Endurance at 70°C

Endurance

Rapid change of

temperature

Bend strength of

the end face plating

Resistance to solvent

Resistance to

soldering heat

Overload ± (2.0%+0.1Ω) Max. 50mΩ

± (1.0%+0.05Ω)

± (3.0%+0.1Ω)

Max. 50mΩ

Max. 100mΩ

J : ±5%

F : ±1%

See Table.1

No remarkable abnormality on the appearance.

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

Without mechanical damage such as breaks.

Max. 50mΩJIS C 5201-1 4.5

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

JIS C 5201-1 4.18

Soldering condition : 260±5

°C

Duration of immersion : 10±1s.

JIS C 5201-1 4.24

°C, 93%RH

Test time : 1,000h to 1,048h

± (3.0%+0.1Ω)

± (1.0%+0.05Ω)

Max. 100mΩ

Max. 50mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70

°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

JIS C 5201-1 4.25.3

125

°C

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23±5

°C

, Immersion cleaning, 5±0.5min.

Solvent : 2-propanol

JIS C 5201-1 4.19

Test temp. : −55

°C

to +125

°C

5cyc

JIS C 5201-1 4.33

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235±5

°C

Duration of immersion : 2.0±0.5s.

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Maximum Overload Voltage : 100V

MNR14

Resistors

Rev.F 3/4

zDimensions (Unit : mm)

Material

Resistive element

(Oxide metal thick film)

Silver thick film electrode

Nickel electrode

Sn electrode

Alumina substrate

Overcoating (Resin)

∗

Marking may change to the one-character type.

∗∗

Pitch of the upper electrode.

Cross section A-A'

Cross section B-B'

0.3±0.2

0.25±0.15

234

0.5

0.1

0.3±0.20.3±0.2

0.6±0.15 0.4±0.15

0.8

103

3.2±0.1

1.6±0.1

zEquivalent circuit

R2R1 R3

R1=R2=R3=R4

zPackaging

0 2

0 4

0 6

0 8

0 2

0 4

0 6

0 8

ABD

Label

ABCD

φ13±0.2

Reel Taping

φD

φ180 0

−3φ60 +1

09 +1.0

φ1.5 +0.1

Chip network

resistors

EIAJ ET-7200B compliant

Thick paper

mount

(Underside paper tape)

Square punchout hole

Heat crimp cover / Tape

(Unit : mm)

3.5±0.05

4.0±0.1

1.75±0.1

4.0±0.1

1.8±0.1

2.0±0.05

3.4±0.1

Max. 1.1

8.0±0.3

MNR14

Resistors

Rev.F 4/4

zPart No. Explanation

E0AP 5,000

Resistance tolerance

Part No.

MN 1R4

Nominal resistance

E0AP J

Paper tape (4mm Pitch)

MNR14 φ180mm (7in.)

J is also used

for jumper

J±5%

F±1%

Part No. Resistance tolerance

J(±5%)J(±5%)

Code Packaging specifications Reel

Basic ordering unit (pcs)

Reel (φ180) : JEITA ET-7200B

: Standard product

Packaging Specifications Code

Resistance code,3 digits,

000 denotes Jumper type.

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any

means without prior permission of ROHM CO.,LTD.

The contents described herein are subject to change without notice. The specifications for the

product described in this document are for reference only. Upon actual use, therefore, please request

that specifications to be separately delivered.

Application circuit diagrams and circuit constants contained herein are shown as examples of standard

use and operation. Please pay careful attention to the peripheral conditions when designing circuits

and deciding upon circuit constants in the set.

Any data, including, but not limited to application circuit diagrams information, described herein

are intended only as illustrations of such devices and not as the specifications for such devices. ROHM

CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any

third party's intellectual property rights or other proprietary rights, and further, assumes no liability of

whatsoever nature in the event of any such infringement, or arising from or connected with or related

to the use of such devices.

Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or

otherwise dispose of the same, no express or implied right or license to practice or commercially

exploit any intellectual property rights or other proprietary rights owned or controlled by

ROHM CO., LTD. is granted to any such buyer.

Products listed in this document are no antiradiation design.

Appendix1-Rev2.0

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

ROHM Customer Support System THE AMERICAS / EUROPE / ASIA / JAPAN

www.rohm.com

The products listed in this document are designed to be used with ordinary electronic equipment or devices

(such as audio visual equipment, office-automation equipment, communications devices, electrical

appliances and electronic toys).

Should you intend to use these products with equipment or devices which require an extremely high level

of reliability and the malfunction of which would directly endanger human life (such as medical

instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers

and other safety devices), please be sure to consult with our sales representative in advance.

It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance

of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow

for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in

order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM

cannot be held responsible for any damages arising from the use of the products under conditions out of the

range of the specifications or due to non-compliance with the NOTES specified in this catalog.

21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121

FAX : +81-75-315-0172

Appendix