SPEC,NO.:MCR-~92064A SPECIFICATIONS FOR MAGNETIC CARD READER Manual Slide type Z=U-Mi12a4 2C]1 JUL. 1992 MATSUSHITA INDUSTRIAL EQUIPMENT Coa, ELECTRONIC EQUIPMENT DIvy,., '-1, 3-Chome, Inazu-cho, Toyonaka Osaka 561, JAPAN LTD.1 1 1 1 0. 1, CONTENTS INTRODUCTION ~~~~_~_~___ PRODUCT NAME ~~~~~~_~_____ FUNCTION ~-~~~~~ ~~ LULL, BASIC CARD CIRCU -EQUIPMENT SPECIFICATION ~~____ FEATURES ~~-~~ ~~ _ STANDARD ~-~~~~_~_ 2 _ IT CONSTRUCTION ~~~_~____. ENVIRONMENTAL CHARACTERISTICS UNIT LIFE AND RELIABILITY ~~~~ PERIOD OF GUARANTEE-~~~~~_~____ MAINTENANCE~~~-~~~~_ 2 HANDLING PRECAUTIONS ~-~_~_______ APPEARANCE ~-~~~~ ~~ 2l. INTRODUCTION This specification describes about manual slide type magnetic card reader, featuring small size, light weight and high performance which enable to read card data encoded by following ISO1,2 standards. 2. PRODUCT NAME 2. 1 Product Name : Manual slide type magnetic card reader 2. 2 Model No. 1 2 4 5 6 7T 8 9g 4Q 2U-Mi12a4e2 m1 Magnetic head specification(S:standard) (L:Long life) 3. FUNCTION 3. 1 Card operation :One way (Refer to appearance) 3. 2 Read/Write Read only 4, EQUIPMENT SPECIFICATION 4. 1 Out dimension :90mm(L) x 25mm(W) x 24mm(H) 4. 2 Weight :Approximately 28 4. 3 Supplied voltage (1) Supplied voltage :+*OVDC+ 10% / Ripple(Less than50mVp-p) (2) Current consumption :TYP. 6mA, MAX. 9mA (3) Maximum applied voltage :+7VDC 4. 4 Connector :>Molex-Japan Co.,Ltd.53261-0990(Refer to 7.5) 4. 5 Environment requirement :At indoor 5. BASIC FEATURES 5. 1 Card operating speed : 10~ 150 cm/sec 5. 2 Magnetic head (1) Numbers of channel :2 (2) Core width : 1.4mm (3) Core material : () Permalloy(S:Standard) ()Sendust (L:Long life)6. CARD STANDARD * 6. ] Card standard - Iso Card Standard Track Ist Track 2nd Recording density 210 BPI 75BPI Recording capacity 79Characters 40Characters (7bit code) (Sbit code) Recording method FM FM Track Ist--- IS O 1 (IATA) International Air Transport Association Track 2nd--- IS O 2 (ABA) :American Bankers Association Standard 6. 2 Location of tracks ISO (2 Tracks) ISO 7810, ISO 781) Coercive force(Hc):300~ 3000(0e) le on a cO E a \O sO ee] col (unit mm) Top of card (f 1Back of card 1) Ist. Track 7 LLLELLLLELLLL EOL gos ee, ZZ. 2nd. Track LLLLLLLELLLL PPD ITIP? | LALLA | m Nt j WN Center line of Center line of ne last data bit first data bit un We", 85.47 ~ 85.72 0.68 ~0.84 |1SO07. CIRCUIT CONST RUCTION 7. 1 Block diagram ZU-M1242 Note) Output Signal: F2F po A +4 CED1 CLD1 r] RCL Ret: | 1501 Magnetic M {Decoding }] RDT RDT1 Head +H CLD2 CLD2 P circuit /+ Rr ReL2 | 07 -4 RDT2 RDT2 of r} +5VDC SGND _ Lf FGND Fig 7.1 Block diagram 7. 2 Interface requirement (1) Signal Level : CMOS level (2) Signal Logic > Low active (3) Connection condition CMOS(MN6541S) (Card Reader side) _ Cable (System side) Fig 7.2 Connection of output circuit (4) Output voltage Table 7.2 Output voltage Min(V) Max(v) Conditions H level 0 4.0 Vee Ton = ~1.0mA it L level 1 - 0.4 To. = 4.0mA _7. 3 Explanation of {nput/output signal 7T Input/output signals are CLD, RCL, RDT, SGND, FGND and effective operation Mode for each of these Signals shall be L leve] for all. (1) CL D(CARD LOAD) : The CLD line will be Low when a Magnetic Card is running in the Magnetic Card Reader. _The CLD line will be High when the Card ts stopped or not present in the Card reader. (2) RCL (READ CLOCK): This is used to sample the data line by It's falling edges. The time relationship of the clock with respect to the order signals is shown in Figure 7.4, (3) RDT(READ DATA) : At the moment RCL change from High to Low: RDF ts 1" when the RDT line is Low, and RDT Is 0 when the RDT line is High. (4) SGND : Signal GND (5) FGND >: Frame GND 7. 4 Output signal timing chart Card Insertion : Card Ejection The magnetic qaqqgs------------------ 2-2 head output /WWW wee eeeeee eee tt CLD on fT R C L - __{ Ae wt tte ee ee ee eee ee LLL _ Il YE | RDP = +}~7qp-----------e eee eee ; All 9 Pee eee ee JUL . All go TYP.6 x T sec, ; Effective data MAX. 30msec. Bit to be neglected Indefinite signals Fig 7.4.1 Timing Sequence RCL&RDT Detail timing chart The magnetic 0 1 ' head output pF RCL H" TIS "TU" t 2 RDT q" + (oR cn LA: Oo BS oO ~>e 2 ER o a 2 Bit data ro" "yt non "gn mye Fig 7.4.2 Timing Sequence (Deta!)) When the jitter of the magnetic head output {s 0%, the following equation is satisfied. T=T)*Te-Te rls 2.54cem/inch 1 Recording density (BPI) Card sneadlam lean T (sec) =7. 8. 8 8. 8 8 5 Terminal No. of connector (1) Maker Molex-Japan Co.,Ltd. (2) Model No. Connector 53261-0990 (Connect for PC. Board) Housing 91021-0900 Terminal 20079-8000 (3) Pin No. & Signal Name ZU-M1242 (Card reader side) Connector | Signal Pin No. Name 1 FGND 2 SGND 3 +5 VDC 4 RDT2 5 RCL2 6 CLD2 7 RDT1 8 RCL1 9 CLD1 Note) : Make sure to use the connection cable of less than 300mm length for the card reader. ENVIRONMENTAL 1 2 3 4 Operating Temperature Range Operating Humidity Range Storage Temperature Range Storage Humidity Range CHARACTERISTICS :-20~ 60C :10~ 90%RH (No condensation allowed) >-30~ 70C :10~95%RH (No condensation allowed) (24 hours) Place the card reader in the standard environment (temperature: 20 + 5C, humidity: 35 to 60%RH).Leave it for 12 hours, and measure the functions.Make sure no abnormality Is found. Vibration Shock durability Others :Vibration sweep 10~50 Hz/mm X,Y,Z directions 2306 :Make sure the source of noise that may deteriorate the characteristics of the card reader is not present around the card reader.9. 1 1 1 1 1 9. I UNIT LIFE AND RELIABILITY Life Magnetic head : CL) 300,000 times pass (S:Standard) : (7 1,000,000 times Pass (L:Long life) (conditions) Ina clean office room. 9. 2 In damp or dirty atmosphere, the life may be 1/3 to 1/5 of the above figure. Error rate : Less than 0.1% (conditions) This error rate is obtained when a new normal card(data "L010": - + jis horizontally passed at the standard speed (30 ~ GOcm/sec.) by manual operation in the clean environ ment at delivery from our company. 0. PERIOD OF GUARANTEE As per PIC's policy of Warranty, 1. MAI NTENANCE Because of difficulty at changing components on the P.c Board, replace of whole unit is recommended for service and maintenance. 2. HANDLING PRECAUTIONS 2. 1 C1) (2) (3) (4) 2. 2 C1) (2) (3) Mounting method Mount on a flat surface, with due care not to apply excessive force on the card reader main body. When mounting on the equipment,take due care so that faces of the constructive device except for the attaching face shall not contact the flexible printed circuit board. The controllability Is most Stable when installed so that the card may run in the vertical direction. The controllability will be further stabilized when card guide Plates are installed before and after the card running part of the card reader, _ Ilandling method Since the reading performance depends on the card inserting direction, insert correctly In the specified direction. The inserting direction I[s specified in the outline drawing of the specification. - If the card Is Inserted obliquely, the contact of the card and magnetic head Is poor, and it may lead to reading error. When inserting the card, the card hits against the head and the action may be dull only for a moment to cause reading error. It must be noted that this phenomenon Is likely to occur when the card is inserted Slowly. AS for card running speed, manipulate within specified speed range. It may result in an error If card operation Is interrupted or extremely accelerated or decelerated. A stable card handling speed by man Is usually 30 to 60 cm/sec.(2) C3) (4) (5) (6) (7) (8) (9) Cautions Use specified card.(ISO) Use the card with the coercive force of 300~ 3000 Oe for ISO. Store the card carefully so as not to soil, injure or deform it. In particular, deposit of solid matter on the magnetic stripe surface may result In a trouble. To prevent wear of the magnetic head, clean the head by periodically passing a cleaning card. For example, in a clean office room, pass the cleaning card about once a week. If the magnetic head is heavily stained, clean the head by soaking the felt part of the cleaning card in alcohol properly. When installing the card reader, avoid dusty, hot or damp place, or near magnetic field or object generating inductive noise (printer, LED display unit, CRT, etc.). Do not use in a place exposed to direct sunlight. When storing, pay attention to dust, heat, humidity and other environmental conditions. Do not touch the printed circuit board with bare hand. Note particularly static electricity. , Do not touch the flexible printed circuit board with hands. Do not supply power from other outlet than connector. Pay special] attention to the polarity of power source and wrong connection of connector. Check the noise, static electricity, etc., with the card reader being incorporated in the equipment.13. APPEARANCE ZLU-M1242*1 aiid Sliding Direction ' 25.4(MAX) Tt Panasonic ZU-M1 0 ve eed a 41 He i Lea Bec 24 Ap 904 0.5 6 780.2 12 662 0.2 2-62.2 /. Tapping Scr /, Tapping Screw Spec. tH | oF (Nominal Diameter2.6) | oa Pa \ connector 5 $3261-0 0990(Molex) General Tolerance : +0.3 unit : mm