Preliminary Specification Number : SP-ZZ1CK-E W-LAN+Bluetooth Combo Module Data Sheet Cypress Chipset for 802.11a/b/g/n/ac + Bluetooth 4.1 Tentative P/N : LBEE5ZZ1CK-TEMP Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 1 / 32 The revision history of the product specification Revised No. B Date 2014/03/28 2015/02/11 C D 2016/4/14 2017/3/3 E 2017/4/12 Note First Issue p4:Adding tolerance p13~20:change output power P23 :correction output power setting Changed IC Part Number P3:Added Certification information P5:Added Label information P28:Added reference circuit P29:Added Packing information Revised BT version P3:1. SCOPE P27:11.10 DC/RF Characteristics for BluetoothLE Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 2 / 32 TABLE OF CONTENTS 1. 2. 3. 4. SCOPE ....................................................................................................................................................... 3 Part Number ............................................................................................................................................... 3 Block Diaglam ............................................................................................................................................ 3 Certification Information ............................................................................................................................. 3 4.1. 5. 6. 7. Radio Certification ..................................................................................................................... 3 DimensionsMarking and Terminal Configuration .................................................................................... 4 Rating ......................................................................................................................................................... 8 Operating Condition ................................................................................................................................... 8 7.1. Operating condition.................................................................................................................... 8 7.2. Power Up Sequence .................................................................................................................. 8 7.2.1 Power On Sequence for WLAN ON and BT ON ................................................................... 8 7.2.2 Power On Sequence for WLAN ON and BT Off .................................................................... 9 7.2.3 Power On Sequence for WLAN OFF and BT ON.................................................................. 9 7.2.4 Power On Sequence for WLAN OFF and BT OFF ................................................................ 9 8 External LPO Signal Requirement ........................................................................................................... 10 9. Digital I/O Requirements .......................................................................................................................... 10 10 Interface timing ...................................................................................................................................... 11 10.1 WLAN SDIO Timing ..................................................................................................................11 10.1.1 SDIO Timing(Default Mode) ..................................................................................................11 10.1.2 SDIO Timing(High Speed Mode).......................................................................................... 12 10.1.3 SDIO timing(SDR mode)...................................................................................................... 12 10.1.4 SDIO Timing(DDR50 mode) ................................................................................................ 15 10.2 Bluetooth UART Timing ........................................................................................................... 17 11 ELECTORICAL CHARACTERISTICS ..................................................................................................... 18 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 11.10 DC/RF Characteristics for IEEE802.11b - 2.4G ...................................................................... 18 DC/RF Characteristics for IEEE802.11g - 2.4G ...................................................................... 19 DC/RF Characteristics for IEEE802.11n - 2.4GHz .................................................................. 20 DC/RF Characteristics for IEEE802.11a - 5GHz ..................................................................... 21 DC/RF Characteristics for IEEE802.11n(HT 20MHz) - 5GHz ................................................. 22 DC/RF Characteristics for IEEE802.11n(HT 40MHz) - 5GHz ................................................. 23 DC/RF Characteristics for IEEE802.11ac(VHT 40MHz) - 5GHz ............................................. 24 DC/RF Characteristics for IEEE802.11ac(VHT 80MHz)-5GHz ............................................... 25 DC/RF Characteristics for Bluetooth ....................................................................................... 26 DC/RF Characteristics for BluetoothLE ........................................................................ 27 12 REFERENCE CIRCUIT........................................................................................................................ 28 13 Packing Information.............................................................................................................................. 29 NOTICE ........................................................................................................................................................... 31 1. Storage Conditions : .................................................................................................................................... 31 2. Handling Conditions :................................................................................................................................... 31 3. Cleaning : ..................................................................................................................................................... 31 4. Operational Environment Conditions : ......................................................................................................... 31 5. Input Power Capacity :................................................................................................................................. 31 PRECONDITION TO USE OUR PRODUCTS ................................................................................................ 32 Please be aware that an important notice concerning availability, standard warranty and use in critical applications of Murata products and disclaimers thereto appears at the end of this specification sheet. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 3 / 32 1. SCOPE This specification is applied to the IEEE802.11a/b/g/n/ac W-LAN + Bluetooth 4.1 combo module. - Module size - IC/Firmware - WLAN Host I/F -Bluetooth Host I/F - Reference Clock - ROM - Weight - RoHS : 33.0 x 18.0 mm typ., t = 7.55 mm max. : Cypress CYW4339 : SDIO3.0 : UART : 37.4MHz Crystal Oscillator embedded : Internal OTP : 2.47g : This module is compliant with the RoHS directive. 2. Part Number Sample Part Number LBEE5ZZ1CK-TEMP 3. Block Diaglam 4. Certification Information 4.1. Radio Certification USA/Canada FCC ID : VPYLB1CK982 IC : 772C-LB1CK982 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 4 / 32 5. DimensionsMarking and Terminal Configuration Dimensions 330.2 23.70.2 4.30.2 3.10.2 1 Shield Case 16 2.7 0.1 Internal Antenna 15 180.2 90.2 30 2.7 9 Unit:mm Indication < connector P/N: DF17(4.0)-30DP-0.5V (mounted on Murata module) P/N: DF17(4.0)-30DS-0.5V (need to place on Customer board) Maker: HIROSE Electric Module side connector [HIROSE] DF17(4.0)-30DP-0.5V Module Attachment Customer side connector [HIROSE] DF17(4.0)-30DS-0.5V Customer Board Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 5 / 32 Marking <Top side> (A) (B) (C) ABC (D) Marking (A) (B) (C) (D) Part Number FCC ID IC ID Trace Number Meaning Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 6 / 32 Terminal Configurations No. Terminal Name Type 1 VBAT PI 2 VBAT PI 3 GND - 4 VIO PI 5 GND - Connection to IC Terminal SR_VDDBATP5V LDO_VDDBAT5V SR_VDDBATP5V LDO_VDDBAT5V PMU_VDDIO VDDIO VDDIO_SD - 6 WLAN_REG_ON I WL_REG_ON 7 BT_REG_ON I BT_REG_ON 8 WLAN_HOST_WAKE I/O GPIO_0 9 GND - - 10 BT_UART_RTS_N O BT_UART_RTS_N 11 BT_UART_TXD O BT_UART_TXD 12 BT_UART_RXD I BT_UART_RXD 13 BT_UART_CTS_N I BT_UART_CTS_N 14 15 16 GND SLEEP_CLK GND I - LPO_IN - 17 BT_DEV_WAKE I/O BT_DEV_WAKE 18 BT_HOST_WAKE I/O BT_HOST_WAKE 19 20 21 22 23 24 25 26 GND SDIO_D2 GND SDIO_D3 GND SDIO_CMD GND SDIO_CLK I/O I/O I/O I No. Terminal Name Type SDIO_DATA2 SDIO_DATA3 SDIO_CMD SDIO_CLK Connection to IC Terminal Description Power VBAT Power VBAT I/O supply for PMU, WLAN, SDIO Used by PMU to power up or power down the internal CYW4339 regulators used by the WLAN section. Also, when deasserted, this pin holds the WLAN section in reset. This pin has an internal 200k ohm pull-down resistor that is enabled by default. It can be disabled through programming. Used by PMU to power up, or power down the internal CYW4339 regulators used by BT section. Also when deasserted, this pin holds the BT/FM section in reset. This pin has an internal 200kohm pull-down resistor that is enabled by default. It can be disabled by programming. This pin can programmed by S/W to be a GPIO, or WLAN_HOST_WAKE output indicating that host wake-up should be performed. UART request-to-send. Active-low request to send signal for HCI UART I/F UART signal output. Serial data output for the HCI UART I/F UART signal input. Serial data input for the HCI UART I/F UART clear_ to_send. Active low. Clear to send signal for HCI UART I/F External Sleep clock input(32.768kHz) DEV_WAKE of general purpose I/O signal HOST_WAKE of general purpose I/O signal SDIO Data Line 2 SDIO Data Line 3 SDIO Command Line SDIO Clock Input Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Description Preliminary Specification Number : SP-ZZ1CK-E 7 / 32 27 28 29 30 GND SDIO_D0 GND SDIO_D1 I/O I/O SDIO_DATA0 SDIO_DATA1 SDIO Data Line 0 SDIO Data Line 1 Terminal Configuration looked from a board implementation side of the customer (16) (15) (30) (1) Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 8 / 32 6. Rating Parameter min. max. Unit Storage Temperature -40 85 deg.C VBAT 0 +5 V Supply Voltage VIO 0 +3.9 V * Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. No damage assuming only one parameter is set at limit at a time with all other parameters are set within operating condition. 7. Operating Condition 7.1. Operating condition Parameter Operating Temperature*1 VBAT Supply Voltage VIO min. -20 3.2 1.71 typ. 25 3.6 1.8 max. 80 4.4 1.89 unit deg.C V V * Surface temperature of shield case 7.2. Power Up Sequence -VBAT should not rise 10%-90%faster than 40 microsecond. -VBAT should be up before or at the same time as VIO. VIO should NOT be present fast or be held high before VBAT is high. 7.2.1 Power On Sequence for WLAN ON and BT ON 32.768kHz Sleep Clock VBAT 90% of VH VIO VDDIO ~2 Sleep cycle WL_REG_ON BT_REG_ON Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 9 / 32 7.2.2 Power On Sequence for WLAN ON and BT OFF 32.768kHz Sleep Clock VBAT 90% of VH VDDIO VIO ~2 Sleep cycle WL_REG_ON BT_REG_ON 7.2.3 Power On Sequence for WLAN OFF and BT ON 32.768kHz Sleep Clock VBAT 90% of VH VDDIO VIO ~2 Sleep cycle WL_REG_ON BT_REG_ON 7.2.4 Power On Sequence for WLAN OFF and BT OFF 32.768kHz Sleep Clock VBAT VDDIO VIO WL_REG_ON BT_REG_ON Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 10 / 32 8 External LPO Signal Requirement Parameter Nominal input frequency Frequency accuracy Duty cycle Input signal amplitude Signal type External LPO Clock 32.768 +/-200 30-70 200 - 1800 Square-wave or sine-wave > 100k <5 <10,000 Input impedance*a Clock jitter (during initial start-up) Unit kHz ppm % mVp-p ohm pF ppm a)When power is applied or switch off. 9. Digital I/O Requirements Digital I/O Pins SDIO Interface I/O Pins@1.8V Input high voltage Input low voltage Output high voltage@2mA Output low voltage@2mA Other Digital I/O Pins@1.8V Input high voltage Input low voltage Output high voltage@2mA Output low voltage@2mA Sym min. typ. max. unit VIH VIL VOH VOL 1.27 1.40 - - 0.58 0.45 V V V V VIH VIL VOH VOL 0.65 x VIO VIO-0.45 - - 0.35 x VIO 0.45 V V V V Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 11 / 32 10 Interface timing 10.1 WLAN SDIO Timing 10.1.1 SDIO Timing(Default Mode) fPP tWL tWH CLK tTHL tISU tTLH tIH Input Output tODLY (max) tODLY (min) SDIO Bus Timing(a) parameters (default Mode) Parameter Symbol Min Typ SDIO CLK (All values are referred to minimum VIH and maximum VIL(b) Frequency-Data Transfer Mode fPP 0 Frequency-Identification Mode fOD 0 Clock Low Time tWL 10 Clock High Time tWH 10 Clock Rise Time tTLH Clock low Time tTHL Inputs: CMD, DAT (referenced to CLK) Input Setup Time tISU 5 Input Hold Time tIH 5 Outputs: CMD, DAT (referenced to CLK) Output Delay time-Data Transfer Mode tODLY 0 Output Delay time-Identification Mode tODLY 0 (a). Timing is based on CL < 40pF load on CMD and Data. (b). Min (Vih) = 0.7*VIO and max (Vil) = 0.2*VIO. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Max Unit 25 400 10 10 MHz kHz ns ns ns ns - ns ns 14 50 ns ns Preliminary Specification Number : SP-ZZ1CK-E 12 / 32 10.1.2 SDIO Timing(High Speed Mode) fPP tWL 50% VDD tWH SDIO_CLK tTHL tISU tTLH tIH Input Output tODLY tOH SDIO Bus Timing(a) parameters (High-Speed Mode) Parameter Symbol Min Typ SDIO CLK (All values are referred to minimum VIH and maximum VIL(b) Frequency-Data Transfer Mode fPP 0 Frequency-Identification Mode fOD 0 Clock Low Time tWL 7 Clock High Time tWH 7 Clock Rise Time tTLH Clock low Time tTHL Inputs: CMD, DAT (referenced to CLK) Input Setup Time tISU 6 Input Hold Time tIH 2 Outputs: CMD, DAT (referenced to CLK) Output Delay time-Data Transfer Mode tODLY Output Hold time tOH 2.5 Total System Capacitance (each line) CL - Max Unit 50 400 3 3 MHz kHz ns ns ns ns - ns ns 14 40 ns ns pF (a). Timing is based on CL < 40pF load on CMD and Data. (b). Min (Vih) = 0.7*VIO and max (Vil) = 0.2*VIO. 10.1.3 SDIO timing(SDR mode) Clock Timing SDIO Bus Clock Timing Parameters(SDR Modes) Parameter Symbol Min Max Unit tclk 40 ns 20 ns 10 ns 4.8 ns tcr, tcf 0.2xtclk ns Clock duty cycle - 30 70 % Comments SDR12 mode SDR25 mode SDR50 mode SDR104 mode tcr, tcf<2.00ns(max)@100MHz, Ccard=10pF tcr, tcf<0.96ns(max)@208MHz, Ccard=10pF ns Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 13 / 32 Device Input Timing SDIO Bus Input Timing Parameters(SDR Modes) Symbol Min Max SDR104 Mode tis 1.4 tih 0.8 SDR50 Mode tis 3.0 tih 0.8 - Unit CommentsUnit ns ns Ccard=10pF, VCT=0.975V Ccard=5pF, VCT=0.975v ns ns Ccard=10pF, VCT=0.975V Ccard=5pF, VCT=0.975V Device Output Timing SDR Modes up to 100MHz SDIO Bus Output Timing Parameters(SDR Modes up to 100MHz) Symbol Min Max Unit CommentsUnit todly 7.5 ns tclk>10ns Cl=30pF using driver tyoe B for SDR50 todly 14.0 ns tclk>20ns Cl=40pF using for SDR12, SDR25 toh 1.5 ns Hold time at the todly(min) Cl=15pF Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 14 / 32 SDR Modes 100MHz to 208MHz SDIO Bus Output Timing Parameters(SDR Modes 100MHz up to 208MHz) Symbol Min Max Unit Comments top 0 2 UI Card output phase -350 +1550 ps Delay variation due to temp change after tuning top todw 0.60 UI todw=2.88ns@208MHz top=+1550 ps for junction temperature of top=90 degrees during operation top=-350 ps for junction temperature of top=-20 degrees during operation top=+2600 ps for junction temperature of top=-20 to +125 degrees during operation top Consideration for Variable Data Window (SDR 104 mode) Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 15 / 32 10.1.4 SDIO Timing(DDR50 mode) SDIO Bus Clock Timing Parameters(DDR50 Mode) parameter Symbol Min Max Unit tclk 20 ns tcr, tcf 0.2xtclk ns Clock duty cycle - 45 55 % Comments DDR50 mode tcr, tcf<4.00ns(max)@50MHz, Ccard=10pF - Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 16 / 32 Data Timing, DDR50 Mode SDIO Bus Timing Parameters(DDR50 Mode) parameter Symbol Min Input CMD Input setup time tisu 6 Input hold time tih 0.8 Output CMD Output delay time todly Output hold time toh 1.5 Input DAT Input setup time tisu2x 3 Input hold time tih2x 0.8 Output DAT Output delay time todly2x Output hold time todly2x 1.5 Max unit Comments - ns ns Ccard<10pF(1 Card) Ccard<10pF(1 Card) 13.7 - ns ns Ccard<30pF(1 Card) Ccard<15pF(1 Card) - ns ns Ccard<10pF(1 Card) Ccard<10pF(1 Card) 7.0 - ns ns Ccard<25pF(1 Card) Ccard<15pF(1 Card) Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 17 / 32 10.2 Bluetooth UART Timing BT_UART_CTS_N 2 Midpoint of STOP bit BT_UART_TXD 1 Midpoint of STOP bit BT_UART_RXD 3 BT_UART_RTS_N Reference 1 2 3 Description Delay time, UART_CTS low to UART_TXD valid Setup time, UART_CTS high before midpoint of stop bit Delay time, midpoint of stop bit to UART_RTS high Min - Typ - Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Max 1.5 0.5 0.5 Unit Bit periods Bit periods Bit periods Preliminary Specification Number : SP-ZZ1CK-E 18 / 32 11 ELECTORICAL CHARACTERISTICS 11.1 DC/RF Characteristics for IEEE802.11b - 2.4G Normal Condition : 25deg.C, VBAT=3.6V. 11Mbps mode unless otherwise specified. Items Specification Mode Channel frequency Data rate Power setting (Tx power, in dBm) Current Consumption Min. (a) Tx mode (99% Tx mode) (b) Rx mode Transmitter Min. Power Levels 15 Spectrum Mask (a) 1st side lobes (b) 2nd side lobes Power-on/off ramp RF Carrier Suppression 15 Modulation Accuracy Spurious Emissions (BW=100kHz) (a) 10MHzf<2387MHz (b) 2387MHzf<2400MHz (c) 2483.5MHz<f2496.5MHz (d) 2496.5MHz<f8GHz Receiver Min. Minimum Input Level (FER< 8%) Maximum Input Level (FER < 8%) -10 Adjacent Channel Rejection (FER< 8%) 35 Contents IEEE802.11b-2.4GHz DSSS / CCK 2412 to 2472 MHz 1, 2, 5.5,11Mbps 17 Typ. Max. 350 100 Typ. Max. 17 19 - unit mA mA Unit dBm - -30 -50 2.0 35 dBr dBr Usec dB % Typ. - -36 -30 -47 -47 Max. -76 - dBm dBm dBm dBm Unit dBm dBm dB Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 19 / 32 11.2 DC/RF Characteristics for IEEE802.11g - 2.4G Normal Condition : 25deg.C, VBAT =3.6V. 54Mbps mode unless otherwise specified. Items Contents Specification IEEE802.11g-2.4GHz Mode OFDM Channel frequency 2412 to 2472 MHz Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps Power setting (Tx power, in dBm) 14 Current Consumption Min. Typ. Max. (a) Tx mode (99% Tx mode) 300 (b) Rx mode 100 Transmitter Min. Typ. Max. Power Levels 12 14 16 Spectrum Mask (a) at fc +/- 11MHz -20 (b) at fc +/- 20MHz -28 (c) at fc > +/-30MHz -40 Constellation Error -25 Spurious Emissions (BW=100kHz) -36 (a) 10MHzf<2387MHz -30 (b) 2387MHzf<2400MHz -47 (c) 2483.5MHz<f2496.5MHz -47 (d) 2496.5MHz<f8GHz Receiver Min. Typ. Max. Minimum Input Level (PER < 10%) -65 Maximum Input Level (PER < 10%) -20 Adjacent Channel Rejection (FER< 10%) -1 - Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Unit mA mA Unit dBm dBr dBr dBr dB dBm dBm dBm dBm Unit dBm dBm dB Preliminary Specification Number : SP-ZZ1CK-E 20 / 32 11.3 DC/RF Characteristics for IEEE802.11n - 2.4GHz Normal Condition : 25deg.C, VBAT =3.6V. 65Mbps (MCS7) mode unless otherwise specified. Items Contents Specification IEEE802.11n-2.4GHz Mode OFDM Channel frequency 2412 to 2472 MHz Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps Power setting (Tx power, in dBm) 13 Current Consumption Min. Typ. Max. (a) Tx mode (99% Tx mode) 300 (b) Rx mode 100 Transmitter Min. Typ. Max. Power Levels 11 13 15 Spectrum Mask (a) at fc +/- 11MHz -20 (b) at fc +/- 20MHz -28 (c) at fc > +/-30MHz -45 Constellation Error -27 Spurious Emissions (BW=100kHz) -36 (a) 10MHzf<2387MHz -30 (b) 2387MHzf<2400MHz -47 (c) 2483.5MHz<f2496.5MHz -47 (d) 2496.5MHz<f8GHz Receiver Min. Typ. Max. Minimum Input Level (PER < 10%) -64 Adjacent Channel Rejection (FER< 10%) -1 - Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Unit mA mA Unit dBm dBr dBr dBr dB dBm dBm dBm dBm Unit dBm dB Preliminary Specification Number : SP-ZZ1CK-E 21 / 32 11.4 DC/RF Characteristics for IEEE802.11a - 5GHz Normal Condition : 25deg.C, VBAT =3.6V. 54Mbps mode unless otherwise specified. Items Contents Specification IEEE802.11a-5GHz Mode OFDM Channel frequency 5180 - 5825MHz Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps Power setting (Tx power, in dBm) 12 Current Consumption min. Typ. Max. (a) Tx mode (99% Tx mode) 350 (b) Rx mode 110 Transmitter min. Typ. Max. Power Levels 10 12 14 Spectrum Mask (a) at fc +/- 11MHz -20 (b) at fc +/- 20MHz -28 (c) at fc > +/-30MHz -40 Constellation Error -25 Spurious Emissions (BW=100kHz) -36 (a) 10MHzf<2387MHz -30 (b) 2387MHzf<2400MHz -47 (c) 2483.5MHz<f2496.5MHz -47 (d) 2496.5MHz<f8GHz Receiver min. Typ. Max. Minimum Input Level (PER < 10%) -65 Adjacent Channel Rejection (FER< 10%) -1 - Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Unit mA mA Unit dBm dBr dBr dBr dB dBm dBm dBm dBm Unit dBm dB Preliminary Specification Number : SP-ZZ1CK-E 22 / 32 11.5 DC/RF Characteristics for IEEE802.11n(HT 20MHz) - 5GHz Normal Condition : 25deg.C, VBAT =3.6V. 65Mbps (MCS7 - HT 20MHz) mode unless otherwise specified. Items Contents Specification IEEE802.11n-5GHz Mode OFDM Channel frequency 5180 - 5825MHz Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps Power setting (Tx power, in dBm) 12 Current Consumption min. Typ. Max. (a) Tx mode (99% Tx mode) 350 (b) Rx mode 110 Transmitter min. Typ. Max. Power Levels 10 12 14 Spectrum Mask (a) at fc +/- 11MHz -20 (b) at fc +/- 20MHz -28 (c) at fc > +/-30MHz -40 Constellation Error (measured at enhanced mode) -27 Spurious Emissions (BW=100kHz) -36 (a) 10MHzf<2387MHz -30 (b) 2387MHzf<2400MHz -47 (c) 2483.5MHz<f2496.5MHz -47 (d) 2496.5MHz<f8GHz Receiver min. Typ. Max. Minimum Input Level (PER < 10%) -64 Adjacent Channel Rejection (FER< 10%) -1 - Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Unit mA mA Unit dBm dBr dBr dBr dB dBm dBm dBm dBm Unit dBm dB Preliminary Specification Number : SP-ZZ1CK-E 23 / 32 11.6 DC/RF Characteristics for IEEE802.11n(HT 40MHz) - 5GHz Normal Condition : 25deg.C, VBAT =3.6V. 135Mbps (MCS7 - HT 40MHz) mode unless otherwise specified. Items Contents Specification IEEE802.11n-5GHz Mode OFDM Channel frequency 5190 - 5795MHz Data rate 13.5, 27, 40.5, 54, 81, 108, 121.5, 135Mbps Power setting (Tx power, in dBm) 11.5 Current Consumption min. Typ. Max. Unit (a) Tx mode (99% Tx mode) 350 mA (b) Rx mode 110 mA Transmitter min. Typ. Max. Unit Power Levels 9.5 11.5 13.5 dBm Spectrum Mask (a) at fc +/- 11MHz -20 dBr (b) at fc +/- 20MHz -28 dBr (c) at fc > +/-30MHz -40 dBr Constellation Error (measured at enhanced mode) -27 dB Spurious Emissions (BW=100kHz) -36 dBm (a) 10MHzf<2387MHz -30 dBm (b) 2387MHzf<2400MHz -47 dBm (c) 2483.5MHz<f2496.5MHz -47 dBm (d) 2496.5MHz<f8GHz Receiver min. Typ. Max. Unit Minimum Input Level (PER < 10%) -61 dBm Adjacent Channel Rejection (FER< 10%) -1 dB Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 24 / 32 11.7 DC/RF Characteristics for IEEE802.11ac(VHT 40MHz) - 5GHz Normal Condition : 25deg.C, VBAT =3.6V. 180Mbps (MCS9 - VHT 40MHz) mode unless otherwise specified. Items Contents Specification IEEE802.11ac-5GHz Mode OFDM Channel frequency 5190 - 5795MHz Data rate 13.5,27,40.5,54,81,108,121.5,135,160,180Mbps Power setting (Tx power, in dBm) 11.5 Current Consumption min. Typ. Max. Unit (a) Tx mode (99% Tx mode) 350 mA (b) Rx mode 130 mA Transmitter min. Typ. Max. Unit Power Levels 9.5 11.5 13.5 dBm Spectrum Mask (a) at fc +/- 21MHz -20 dBr (b) at fc +/- 40MHz -28 dBr (c) at fc > +/-60MHz -40 dBr Constellation Error (measured at enhanced mode) -32 dB Spurious Emissions (BW=100kHz) -36 dBm (a) 10MHzf<2387MHz -30 dBm (b) 2387MHzf<2400MHz -47 dBm (c) 2483.5MHz<f2496.5MHz -47 dBm (d) 2496.5MHz<f8GHz Receiver min. Typ. Max. Unit Minimum Input Level (PER < 10%) -54 dBm Adjacent Channel Rejection (FER< 10%) -1 dB Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 25 / 32 11.8 DC/RF Characteristics for IEEE802.11ac(VHT 80MHz)-5GHz Normal Condition : 25deg.C, VBAT =3.6V. 390Mbps (MCS9 - VHT 80MHz) mode unless otherwise specified. Items Contents Specification IEEE802.11ac-5GHz Mode OFDM Channel frequency 5210 - 5775MHz Data rate 29.3,58.5,87.8,117,175.5,234,263.3,292.5,351,390Mbps Power setting (Tx power, in dBm) 11 Current Consumption min. Typ. Max. Unit (a) Tx mode (99% Tx mode) 350 mA (b) Rx mode 160 mA Transmitter min. Typ. Max. Unit Power Levels 9 11 13 dBm Spectrum Mask (a) at fc +/- 41MHz -20 dBr (b) at fc +/- 80MHz -28 dBr (c) at fc > +/-120MHz -40 dBr Constellation Error (measured at enhanced mode) -32 dB Spurious Emissions (BW=100kHz) -36 dBm (a) 10MHzf<2387MHz -30 dBm (b) 2387MHzf<2400MHz -47 dBm (c) 2483.5MHz<f2496.5MHz -47 dBm (d) 2496.5MHz<f8GHz Receiver min. Typ. Max. Unit Minimum Input Level (PER < 10%) -51 dBm Adjacent Channel Rejection (FER< 10%) -1 dB Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 26 / 32 11.9 DC/RF Characteristics for Bluetooth Normal conditions : 25 deg.C, VBAT = 3.6V Items Contents Bluetooth specification (power class) Version 2.1+EDR (Class1) Channel frequency (spacing) 2402 to 2480 MHz (1MHz) Current Consumption Min. Typ. Max. (a) DH5 Packet 50% Rx/Tx slot duty cycle 90 (b) 2DH5 Packet 50% Rx/Tx slot duty cycle 80 (c) 3DH5 Packet 50% Rx/Tx slot duty cycle 80 Transmitter Min. Typ. Max. Output Power *1 7 11 15 Frequency range 2400 2483.5 20dB bandwidth 1 Adjacent Channel Power *2 (a) [M-N] =2 -20 (b) [M-N] 3 -40 Modulation characteristics (a) Modulation f1avg 140 175 (b) Modulation f2max 115 (c) Modulation f2avg / f1avg 0.8 Carrier Frequency Drift (a) 1slot -25 +25 (b) 3slot / 5slot -40 +40 (c) Maximum drift rate -20 +20 EDR Relative Power -4 +1 EDR Carrier Frequency Stability and Modulation Accuracy (a) i -75 +75 (b) i+o -75 +75 (c) o -10 +10 (d) RMS DEVM (DQPSK) 20 (e) Peak DEVM (DQPSK) 35 (f) 99% DEVM (DQPSK) 30 (g) RMS DEVM (8DPSK) 13 (h) Peak DEVM (8DPSK) 25 (i) 99% DEVM (8DPSK) 20 Spurious Emissions (BW=100kHz) -36 (a) 10MHzf<2387MHz -30 (b) 2387MHzf<2400MHz -47 (c) 2483.5MHz<f2496.5MHz -47 (d) 2496.5MHz<f8GHz Receiver Min. Typ. Max. Sensitivity (BER<0.1%) -80 C/I Performance (BER<0.1%) *3 (a) co-channel 11 (b) 1MHz 0 (c) 2MHz -30 (d) 3MHz -40 (e) image (+4MHz) -9 (f) image +/- 1MHz -20 Maximum Input Level (BER<0.1%) -20 EDR Sensitivity (BER<0.007%) (a) 8DPSK -77 *1: Up to three spurious responses within Bluetooth limits are allowed. *2: Up to five spurious responses within Bluetooth limits are allowed. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Unit mA mA mA Unit dBm MHz MHz dBm dBm kHz kHz kHz kHz kHz/50us dB kHz kHz kHz % % % % % % dBm dBm dBm dBm Unit dBm dB dB dB dB dB dB dBm dBm Preliminary Specification Number : SP-ZZ1CK-E 27 / 32 11.10 DC/RF Characteristics for BluetoothLE Normal conditions : 25 deg.C, VBAT = 3.6V Items Bluetooth specification (power class) Channel frequency (spacing) Number of RF Channel Item / Condition Center Frequency Channel Spacing Number of RF channel Output power *1 Modulation Characteristics 1) f1avg 2) f2max (at 99.9%) 3) f2avg / f1avg Carrier frequency offset and drift 1) Frequency offset 2) Frequency drift 3) Drift rate Receiver sensitivity (PER < 30.8%) Maximum input signal level (PER < 30.8%) PER Report Integrity (-30dBm input) Contents Version 4.1(LE) 2402 to 2480 MHz (2MHz) 40 Min. Typ. Max. 2402 2480 2 40 10 Unit MHz MHz dBm 225 185 0.8 - 275 - kHz kHz - -10 50 - 150 50 20 -70 65.4 kHz kHz kHz dBm dBm % Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 28 / 32 12 REFERENCE CIRCUIT A B C D E F 1 1 VIO 2 2 10kohm~ 100kohm 16 17 BT_DEV_WAKE 18 BT_HOST_WAKE 19 20 SDIO_D2 21 22 SDIO_D3 23 3 24 SDIO_CMD 25 26 SDIO_CLK 27 28 SDIO_D0 29 30 SDIO_D1 GND SLEEP_CLK BT_DEV_WAKE GND BT_HOST_WAKE BT_UART_CTS_N GND BT_UART_RXD SDIO_D2 BT_UART_TXD GND BT_UART_RTS_N SDIO_D3 GND GND WLAN_HOST_WAKE SDIO_CMD BT_REG_ON GND WLAN_REG_ON SDIO_CLK GND GND VIO SDIO_D0 GND GND VBAT SDIO_D1 VBAT 15 SLEEP_CLK_IN(32.768kHz) 14 13 BT_UART_CTS_N 12 BT_UART_RXD 11 BT_UART_TXD 10 BT_UART_RTS_N 9 8 WLAN_HOST_WAKE 7 BT_REG_ON 6 3 VIO WLAN_REG_ON 5 VBAT 4 3 2 1 1uF 4.7uF TYPE1CK GND GND GND GND 4 4 5 5 A B C D E Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. F Preliminary Specification Number : SP-ZZ1CK-E 29 / 32 13 Packing Information The products shall be packed in the below tray. Number of the products in the carton is 210pcs. There is the 42pcs per tray and 5pile number of the tray which stored the product. Finally, a dummy tray is put on the topmost part of trays. Packing in a inner box Tray(Upper lid) module Tray (5 sheets) Inner box cushioning Shipping box Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 30 / 32 Inner Box Shipping Box - Please keep any packaging below 40 deg.C until using it up, because a tray is potentially deformed with storage over the temperature. Please don't stack the shipping box over 1.5m height to avoid any physical problem. Four inner boxes is general number in a shipping box, but it may be dummy for some of inner boxes. One inner box has 210pcs as standard q'ty. MOQ is 840pcs, which are constructed two inner boxes. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 31 / 32 NOTICE 1. Storage Conditions : Please use this product within 6month after receipt. - The product shall be stored without opening the packing under the ambient temperature from 5 to 35deg.C and humidity from 20 to 70%RH. (Packing materials, in particular, may be deformed at the temperature over 40deg.C.) - The product left more than 6months after reception, it needs to be confirmed the solderbility before used. - The product shall be stored in non corrosive gas (Cl2, NH3, SO2, Nox, etc.). - Any excess mechanical shock including, but not limited to, sticking the packing materials by sharp object and dropping the product, shall not be applied in order not to damage the packing materials. 2. Handling Conditions : Be careful in handling or transporting products because excessive stress or mechanical shock may break products. Handle with care if products may have cracks or damages on their terminals, the characteristics of products may change. Do not touch products with bear hands that may destroy by static electrical charge. 3. Cleaning : Since this Product is Moisture Sensitive, any cleaning is not permitted. 4. Operational Environment Conditions : Products are designed to work for electronic products under normal environmental conditions (ambient temperature, humidity and pressure). Therefore, products have no problems to be used under the similar conditions to the above-mentioned. However, if products are used under the following circumstances, it may damage products and leakage of electricity and abnormal temperature may occur. - In an atmosphere containing corrosive gas ( Cl2, NH3, SOx, NOx etc.). - In an atmosphere containing combustible and volatile gases. - Dusty place. - Direct sunlight place. - Water splashing place. - Humid place where water condenses. - Freezing place. If there are possibilities for products to be used under the preceding clause, consult with Murata before actual use. As it might be a cause of degradation or destruction to apply static electricity to products, do not apply static electricity or excessive voltage while assembling and measuring. 5. Input Power Capacity : Products shall be used in the input power capacity as specified in this specifications. Inform Murata beforehand, in case that the components are used beyond such input power capacity range. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Preliminary Specification Number : SP-ZZ1CK-E 32 / 32 PRECONDITION TO USE OUR PRODUCTS PLEASE READ THIS NOTICE BEFORE USING OUR PRODUCTS. Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the specifications of our product when our product is mounted to your product. All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment specified in this specification. You are requested not to use our product deviating from the condition and the environment specified in this specification. Please note that the only warranty that we provide regarding the products is its conformance to the specifications provided herein. Accordingly, we shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this specification. WE HEREBY DISCLAIMS ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY ARE DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. The product shall not be used in any application listed below which requires especially high reliability for the prevention of such defect as may directly cause damage to the third party's life, body or property. You acknowledge and agree that, if you use our products in such applications, we will not be responsible for any failure to meet such requirements. Furthermore, YOU AGREE TO INDEMNIFY AND DEFEND US AND OUR AFFILIATES AGAINST ALL CLAIMS, DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION, ATTORNEY FEES AND COSTS, DUE TO THE USE OF OUR PRODUCTS IN SUCH APPLICATIONS. - Aircraft equipment. - Aerospace equipment - Undersea equipment. - Power plant control equipment - Medical equipment. - Transportation equipment (vehicles, trains, ships, elevator, etc.). - Traffic signal equipment. - Disaster prevention / crime prevention equipment. -Burning / explosion control equipment - Application of similar complexity and/ or reliability requirements to the applications listed in the above. We expressly prohibit you from analyzing, breaking, reverse-engineering, remodeling altering, and reproducing our product. Our product cannot be used for the product which is prohibited from being manufactured, used, and sold by the regulations and laws in the world. We do not warrant or represent that any license, either express or implied, is granted under any our patent right, copyright, mask work right, or our other intellectual property right relating to any combination, machine, or process in which our products or services are used. Information provided by us regarding third-party products or services does not constitute a license from us to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from us under our patents or other intellectual property. Please do not use our products, our technical information and other data provided by us for the purpose of developing of mass-destruction weapons and the purpose of military use. Moreover, you must comply with "foreign exchange and foreign trade law", the "U.S. export administration regulations", etc. Please note that we may discontinue the manufacture of our products, due to reasons such as end of supply of materials and/or components from our suppliers. By signing on specification sheet or approval sheet, you acknowledge that you are the legal representative for your company and that you understand and accept the validity of the contents herein. When you are not able to return the signed version of specification sheet or approval sheet within 30 days from receiving date of specification sheet or approval sheet, it shall be deemed to be your consent on the content of specification sheet or approval sheet. Customer acknowledges that engineering samples may deviate from specifications and may contain defects due to their development status. We reject any liability or product warranty for engineering samples. In particular we disclaim liability for damages caused by - the use of the engineering sample other than for evaluation purposes, particularly the installation or integration in the product to be sold by you, -deviation or lapse in function of engineering sample, -improper use of engineering samples. We disclaim any liability for consequential and incidental damages. If you can't agree the above contents, you should inquire our sales. Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd.