RUGGEDCOM SFP Transceivers
Catalog
04/2019
RC1251-EN-14
Preface
Introduction 1
Copper SFP Transceivers 2
Fast Ethernet SFP
Transceivers 3
Active 100 Mbps SFP
Transceivers 4
Gigabit Ethernet SFP
Transceivers 5
Bidirectional Gigabit
Ethernet SFP Transceivers 6
10-Gigabit Ethernet SFP+
Transceivers 7
Installation/Removal 8
RUGGEDCOM SFP Transceivers
Catalog
ii
Copyright © 2019 Siemens Canada Ltd
All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized
except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or
trademark registration.
This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be
photocopied, reproduced or translated to another language without the prior written consent of Siemens Canada Ltd.
Disclaimer Of Liability
Siemens has verified the contents of this document against the hardware and/or software described. However, deviations between the product
and the documentation may exist.
Siemens shall not be liable for any errors or omissions contained herein or for consequential damages in connection with the furnishing,
performance, or use of this material.
The information given in this document is reviewed regularly and any necessary corrections will be included in subsequent editions. We
appreciate any suggested improvements. We reserve the right to make technical improvements without notice.
Registered Trademarks
RUGGEDCOM™ and ROS™ are trademarks of Siemens Canada Ltd.
Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the
owner.
Security Information
Siemens provides products and solutions with industrial security functions that support the secure operation of plants, machines, equipment
and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens' products and solutions
undergo continuous development. Siemens recommends strongly that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and
integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be
considered. For more information about industrial security, visit https://www.siemens.com/industrialsecurity.
To stay informed about product updates as they occur, sign up for a product-specific newsletter. For more information, visit https://
support.automation.siemens.com.
Warranty
For warranty details, visit https://www.siemens.com/ruggedcom or contact a Siemens customer service representative.
Contacting Siemens
Address
Siemens Canada Ltd
Industry Sector
300 Applewood Crescent
Concord, Ontario
Canada, L4K 5C7
Telephone
Toll-free: 1 888 264 0006
Tel: +1 905 856 5288
Fax: +1 905 856 1995
E-mail
ruggedcom.info.i-ia@siemens.com
Web
https://www.siemens.com/ruggedcom
RUGGEDCOM SFP Transceivers
Catalog
Table of Contents
iii
Table of Contents
Preface ............................................................................................................. v
Alerts .................................................................................................................................................. v
Training .............................................................................................................................................. vi
Customer Support ............................................................................................................................... vi
Ordering RUGGEDCOM Products ........................................................................................................... vi
Chapter 1
Introduction ..................................................................................................... 1
1.1Selecting an SFP Transceiver .......................................................................................................... 2
1.2Available SFP Transceivers ............................................................................................................. 3
Chapter 2
Copper SFP Transceivers ................................................................................... 5
2.1RUGGEDCOM SFP1112-1 ............................................................................................................... 6
Chapter 3
Fast Ethernet SFP Transceivers .......................................................................... 9
3.1RUGGEDCOM SFP1121-1FX2 ........................................................................................................ 10
3.2RUGGEDCOM SFP1131-1FX20 ...................................................................................................... 12
3.3RUGGEDCOM SFP1131-1FX50 ...................................................................................................... 14
3.4RUGGEDCOM SFP1131-1FX90 ...................................................................................................... 16
Chapter 4
Active 100 Mbps SFP Transceivers ................................................................... 17
4.1RUGGEDCOM SFP1121-1FX2A ...................................................................................................... 18
4.2RUGGEDCOM SFP1131-1FX10A .................................................................................................... 20
4.3RUGGEDCOM SFP1131S-1FX40A .................................................................................................. 22
Chapter 5
Gigabit Ethernet SFP Transceivers ................................................................... 25
5.1RUGGEDCOM SFP1122-1SX ......................................................................................................... 26
5.2RUGGEDCOM SFP1122-1SX2 ........................................................................................................ 28
5.3RUGGEDCOM SFP1132-1LX10 ...................................................................................................... 29
5.4RUGGEDCOM SFP1132-1LX25 ...................................................................................................... 31
5.5RUGGEDCOM SFP1132-1LX40 ...................................................................................................... 32
5.6RUGGEDCOM SFP1132-1LX70 ...................................................................................................... 33
Table of Contents
RUGGEDCOM SFP Transceivers
Catalog
iv
5.7RUGGEDCOM SFP1132-1LX100 .................................................................................................... 34
5.8RUGGEDCOM SFP1132-1LX115 .................................................................................................... 35
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers ................................................ 37
6.1RUGGEDCOM SFP1132-1BX10R .................................................................................................... 38
6.2RUGGEDCOM SFP1132-1BX10T .................................................................................................... 40
6.3RUGGEDCOM SFP1132-1BX40R .................................................................................................... 42
6.4RUGGEDCOM SFP1132-1BX40T .................................................................................................... 44
Chapter 7
10-Gigabit Ethernet SFP+ Transceivers ............................................................. 47
7.1RUGGEDCOM SFP2123-1SR .......................................................................................................... 48
7.2RUGGEDCOM SFP2133-1LR10 ...................................................................................................... 50
7.3RUGGEDCOM SFP2133-1ER40 ...................................................................................................... 52
7.4RUGGEDCOM SFP2133-1ZR80 ...................................................................................................... 54
Chapter 8
Installation/Removal ........................................................................................ 55
8.1Handling SFP Transceivers ........................................................................................................... 56
8.2Required Tools ............................................................................................................................ 57
8.3Installation ................................................................................................................................. 58
8.4Removal ..................................................................................................................................... 60
RUGGEDCOM SFP Transceivers
Catalog
Preface
Alerts v
Preface
This document details the available SFP transceivers, including compatibility with the RUGGEDCOM product line,
technical specifications, installation/removal instructions, and ordering information.
It is intended for use by network technical support personnel responsible for the installation, commissioning and
maintenance of routers and switches. It is also recommended for use by network and system planners, system
programmers, and line technicians.
CONTENTS
•“Alerts”
•“Training”
•“Customer Support”
•“Ordering RUGGEDCOM Products”
Alerts
The following types of alerts are used when necessary to highlight important information.
DANGER!
DANGER alerts describe imminently hazardous situations that, if not avoided, will result in death or
serious injury.
WARNING!
WARNING alerts describe hazardous situations that, if not avoided, may result in serious injury and/or
equipment damage.
CAUTION!
CAUTION alerts describe hazardous situations that, if not avoided, may result in equipment damage.
IMPORTANT!
IMPORTANT alerts provide important information that should be known before performing a procedure
or step, or using a feature.
NOTE
NOTE alerts provide additional information, such as facts, tips and details.
Preface
RUGGEDCOM SFP Transceivers
Catalog
vi Training
Training
Siemens offers a wide range of educational services ranging from in-house training of standard courses on
networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs,
experience and application.
Siemens' Educational Services team thrives on providing our customers with the essential practical skills to make
sure users have the right knowledge and expertise to understand the various technologies associated with critical
communications network infrastructure technologies.
Siemens' unique mix of IT/Telecommunications expertise combined with domain knowledge in the utility,
transportation and industrial markets, allows Siemens to provide training specific to the customer's application.
For more information about training services and course availability, visit https://www.siemens.com/ruggedcom or
contact a Siemens Sales representative.
Customer Support
Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general
information, contact Siemens Customer Support through any of the following methods:
Online
Visit http://www.siemens.com/automation/support-request to submit a Support Request (SR) or check
on the status of an existing SR.
Telephone
Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit http://
www.automation.siemens.com/mcms/aspa-db/en/automation-technology/Pages/default.aspx.
Mobile App
Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile
device and be able to:
• Access Siemens' extensive library of support documentation, including FAQs and manuals
• Submit SRs or check on the status of an existing SR
• Contact a local Siemens representative from Sales, Technical Support, Training, etc.
• Ask questions or share knowledge with fellow Siemens customers and the support community
Ordering RUGGEDCOM Products
Use the RUGGEDCOM-Selector to select and configure RUGGEDCOM products and accessories. Once selected, an
item(s) can be transferred to the Siemens Industry Mall and ordered.
RUGGEDCOM-Selector
http://www.siemens.com/ruggedcom-selector.
For more information, refer to https://www.siemens.com/ruggedcom.
RUGGEDCOM SFP Transceivers
Catalog
Chapter 1
Introduction
1
Introduction
Siemens offers a wide range of convenient and cost-effective Fast Ethernet Small Form-Factor Pluggable (SFP)
transceivers for select RUGGEDCOM routers and switches. SFP transceivers offer a variety of options for speed,
distance and interfaces to extend the reach and functionality of networks.
IMPORTANT!
Only use SFP transceivers approved by Siemens for RUGGEDCOM products. Siemens accepts no liability
as a result of performance issues related in whole or in part to third-party components.
IMPORTANT!
SFP transceivers contain no user-serviceable parts. Attempted service by unauthorized personnel shall
render all warranties null and void.
Changes or modifications not expressly approved by Siemens could invalidate specifications, test
results, and agency approvals, and void the user's authority to operate the product.
NOTE
All SFP transceivers are compatible with the Small Form-Factor Pluggable 20-pin Multi-Source
Agreement (MSA).
NOTE
Maximum segment length is greatly dependent on factors such as fiber quality and the number of
patches and splices. Consult a Siemens sales associate when determining maximum segment lengths.
NOTE
All optical power numbers are listed as dBm averages.
CONTENTS
•Section1.1, “Selecting an SFP Transceiver”
•Section1.2, “Available SFP Transceivers”
Chapter 1
Introduction
RUGGEDCOM SFP Transceivers
Catalog
2 Selecting an SFP Transceiver
Section1.1
Selecting an SFP Transceiver
The following process for selecting an SFP transceiver is recommended:
1. Determine the basic application requirements, such as SFP type, link speed and operating distance, and then
select an SFP transceiver.
2. Determine which RUGGEDCOM product(s) support the chosen SFP transceiver.
3. If the chosen SFP transceiver will be connected a fixed port or to a non-RUGGEDCOM device, review the full
technical specifications for the SFP transceiver to make sure it is compatible with the other end of the link.
For a list of available SFP transceivers and general specifications, refer to Section1.2, “Available SFP Transceivers”.
If assistance is required to select the appropriate SFP transceiver for the application, contact Siemens Customer
Support.
RUGGEDCOM SFP Transceivers
Catalog
Chapter 1
Introduction
Available SFP Transceivers 3
Section1.2
Available SFP Transceivers
Each available SFP transceiver has been tested for compatibility with the following RUGGEDCOM routers and
switches. Use in any other RUGGEDCOM or third-party router/switch is not supported or recommended by
Siemens.
NOTE
Compatibility with some RUGGEDCOM routers/switches may contain restrictions. For more information
about product-specific deviations, refer to the detailed description of the relevant SFP transceiver(s) in
this catalog.
Chapter 1
Introduction
RUGGEDCOM SFP Transceivers
Catalog
4 Available SFP Transceivers
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ●
●
●
● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ●
● ●
● ●
● ●
Type
Media
Distance (km)
SFP Name Article Number
RS900G
RS900GP
RS940G
RSL910
RSG908C
RSG910C
RSG920P
RSG2100(P)
RSG2200
RSG2288
RSG2300(P)
RSG2488
RS950G
RSG907R
RSG909R
RX1400
Copper RJ45 0.1 SFP1112-1 6GK6000-8CG01-0AA0
100 Mbps
Active
MM 2 SFP1121-1FX2A 6GK6000-8FE50-0AA0
100 Mbps
MM 2 SFP1121-1FX2 6GK6000-8FE51-0AA0
1 Gbps
Single-fiber
Bidirectional
SM
10 SFP1132-1BX10R 6GK6000-8FB51-0AA0
1 Gbps
MM 0.5 SFP1122-1SX 6GK6000-8FG51-0AA0
2 SFP1122-1SX2 6GK6000-8FE58-0AA0
SM
10 SFP1132-1LX10 6GK6000-8FG52-0AA0
25 SFP1132-1LX25 6GK6000-8FG53-0AA0
40 SFP1132-1LX40 6GK6000-8FG57-0AA0
70 SFP1132-1LX70 6GK6000-8FG54-0AA0
100 SFP1132-1LX100 6GK6000-8FG55-0AA0
115 SFP1132-1LX115 6GK6000-8FE56-0AA0
10 Gbps
MM 0.4 SFP2123-1SR 6GK6000-8FT50-0AA0
SM
10 SFP2133-1LR10 6GK6000-8FT51-0AA0
40 SFP2133-1ER40 6GK6000-8FT53-0AA0
80 SFP2133-1ZR80 6GK6000-8FT52-0AA0
SM 10 SFP1131-1FX10A 6GK6000-8FE60-0AA0
40 SFP1131S-1FX40A 6GK6000-8FE62-0AA0
SM
20 SFP1131-1FX20 6GK6000-8FE52-0AA0
50 SFP1131-1FX50 6GK6000-8FE53-0AA0
90 SFP1131-1FX90 6GK6000-8FE54-0AA0
SFP1132-1BX10T 6GK6000-8FB52-0AA0
40 SFP1132-1BX40R 6GK6000-8FB53-0AA0
SFP1132-1BX40T 6GK6000-8FB54-0AA0
RUGGEDCOM SFP Transceivers
Catalog
Chapter 2
Copper SFP Transceivers
5
Copper SFP Transceivers
The following copper triple-speed SFP transceivers are available from Siemens for select RUGGEDCOM routers and
switches. To determine compatibility, refer to Section1.2, “Available SFP Transceivers”.
CONTENTS
•Section2.1, “RUGGEDCOM SFP1112-1”
Chapter 2
Copper SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
6 RUGGEDCOM SFP1112-1
Section2.1
RUGGEDCOM SFP1112-1
Siemens' RUGGEDCOM SFP1112-1 is a 1 Gbps copper SFP transceiver that operates within a wide temperature
range (0 to 70 °C or 32 to 158 °F) and provides high performance Gigabit Ethernet communication up to 100 m
(328.1 ft).
NOTE
This SFP transceiver is not recommended for use with IEEE 1588.
Highlights
• Compliant with SFP MSA and IEEE 802.3ab for
10/100/1000Base-T
• Transmission distance up to 100 m (328.1 ft)
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Characteristics
Speed 10/100/1000 Mbps
Connector RJ-45
Cable Type > CAT-5e
Duplex FDX/HDX
Wiring Standard TIA/EIA T568A/B
Nominal Distance 100 m (328.1 ft)
Isolation 1.5 kV
Environment
Operating Temperature 0 to 70 °C (32 to 158 °F)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Product-Specific Deviations
The RUGGEDCOM SFP1112-1 supports the following ratings when installed in the specified Siemens RUGGEDCOM
routers and/or switches:
Product(s) Specification Rating
RUGGEDCOM RSG907R, RSG909R Speed Supports only 1000 Mbps on the coupler
port on RUGGEDCOM ROS v5.2 firmware
versions
RUGGEDCOM RSG908C, RSG910C Speed Supports only 1000 Mbps on RUGGEDCOM
ROS v5.2 firmware versions
Regulatory Compliance
The RUGGEDCOM SFP1112-1 meets the following standards when installed in Siemens RUGGEDCOM routers and/
or switches:
RUGGEDCOM SFP Transceivers
Catalog
Chapter 2
Copper SFP Transceivers
RUGGEDCOM SFP1112-1 7
Feature Standard Performance
Electromagnetic Interference (EMI) FCC Class A, CE Class A, VCCI Class A, C-Tick Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8CG01-0AA0 RUGGEDCOM SFP1112-1 1000Base-T SFP – RJ45, 100 m
Chapter 2
Copper SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
8 RUGGEDCOM SFP1112-1
RUGGEDCOM SFP Transceivers
Catalog
Chapter 3
Fast Ethernet SFP Transceivers
9
Fast Ethernet SFP Transceivers
The following Fast Ethernet SFP transceivers are available from Siemens for select RUGGEDCOM routers and
switches. To determine compatibility, refer to Section1.2, “Available SFP Transceivers”.
CONTENTS
•Section3.1, “RUGGEDCOM SFP1121-1FX2”
•Section3.2, “RUGGEDCOM SFP1131-1FX20”
•Section3.3, “RUGGEDCOM SFP1131-1FX50”
•Section3.4, “RUGGEDCOM SFP1131-1FX90”
Chapter 3
Fast Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
10 RUGGEDCOM SFP1121-1FX2
Section3.1
RUGGEDCOM SFP1121-1FX2
Siemens' RUGGEDCOM SFP1121-1FX2 industrial grade 100 Mbps fiber optic fast Ethernet SFP transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Fast Ethernet
communication up to 2 km (1.2 mi) using multi-mode fiber.
Highlights
• Compliant with SFP MSA and IEEE 802.3ab for 100Base-FX
• Transmission distance up to 2 km (1.2 mi)
• LC duplex connector optical interface
• Operates with 50/125 μm and 62.5/125 μm multi-mode fiber
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power (50/125 μm) -23.5 to -14.0 dBm
Transmit Power (62.5/125 μm) -20.0 to -14.0 dBm
Receiver Sensitivity -31.0 to -3.0 dBm
Power Budget (50/125 μm) 7.5 dB
Power Budget (62.5/125 μm) 11 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Storage Temperature -40 to 100 °C (-40 to 212 °F)
Cabling
Speed 100 Mbps
Mode MM (Multi-Mode)
Interface FX
Connector LC
Cable Type 50/125 or 62.5/125 μm
Wavelength 1310 nm
Nominal Distance 2 km (1.2 mi)
Regulatory Compliance
The RUGGEDCOM SFP1121-1FX2 meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883C HBM 2 kV
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
Variation of IEC 61000-4-2 Compliant
Electromagnetic Interference (EMI) CENELEC CEN55022 Class B Compliant
Immunity Variation of IEC 61000-4-3 Compliant
Eye Safety AEL Class 1
EN 60825-1 (+A11)
Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
RUGGEDCOM SFP Transceivers
Catalog
Chapter 3
Fast Ethernet SFP Transceivers
RUGGEDCOM SFP1121-1FX2 11
Ordering Information
Article Number Name Description
6GK6000-8FE51-0AA0 RUGGEDCOM SFP1121-1FX2 100Base-FX SFP – MM, 1310 nm, LC, 2 km
Chapter 3
Fast Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
12 RUGGEDCOM SFP1131-1FX20
Section3.2
RUGGEDCOM SFP1131-1FX20
Siemens' RUGGEDCOM SFP1131-1FX20 industrial grade 100 Mbps fiber optic fast Ethernet SFP transceiver
operates within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Fast
Ethernet communication up to 20 km (12.4 mi) using single-mode fiber.
NOTE
Maximum distance is 15 km (9.3 mi) in OC-3 mode.
Highlights
• Compliant with SFP MSA for 100Base-FX
• Transmission distance up to 20 km (12.4 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -15 to -8 dBm
Receiver Sensitivity -31 to -8 dBm
Power Budget 16 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 0 to 85% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 100 Mbps
Interface FX
Mode SM (Single-Mode)
Connector LC
Cable Type 9/125 μm
Wavelength 1300 nm
Nominal Distance 20 km (12.4 mi)
Regulatory Compliance
The RUGGEDCOM SFP1131-1FX20 complies with the following regulatory requirements when installed in Siemens
RUGGEDCOM routers and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883C, Method 3015.4
JEDEC/EIA JESD22-A114-A
Class 2 (2000 V)
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
Bellcore GR1089-CORE 25 kV Air Discharge
10 Zaps at 8 kV (contact discharge) on the
electrical faceplate on panel
Electromagnetic Interference (EMI) FCC Class B Compliant
Immunity Variation of IEC 61000-4-3 Compliant
Eye Safety US FDA CDRH AEL Class 1
IEC/EN 60825-1 and 60825-2
Compliant with Class 1 laser product
RUGGEDCOM SFP Transceivers
Catalog
Chapter 3
Fast Ethernet SFP Transceivers
RUGGEDCOM SFP1131-1FX20 13
Feature Standard Performance
EN 60950 Class 1
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FE52-0AA0 RUGGEDCOM SFP1131-1FX20 100Base-FX SFP – SM, 1300 nm, LC, 20 km
Chapter 3
Fast Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
14 RUGGEDCOM SFP1131-1FX50
Section3.3
RUGGEDCOM SFP1131-1FX50
Siemens' RUGGEDCOM SFP1131-1FX50 industrial grade 100 Mbps fiber optic fast Ethernet SFP transceiver
operates within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Fast
Ethernet communication up to 50 km (31.1 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA and SFF 8074i for 100Base-
FX
• Compliant with SFF-8472 Digital Diagnostic
Monitoring Interface
• Compliant with ITU-T G957 STM-1 L1.1 Optical
Interface
• Compliant with Telcordia GR253 OC3 LR-1 Optical
Interface
• Transmission distance up to 50 km (31.1 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -5 to -0 dBm
Receiver Sensitivity -34 to -0 dBm
Power Budget 29
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 0 to 85% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 100 Mbps
Mode SM (Single-Mode)
Interface FX
Connector LC
Cable Type 9/125 μm
Wavelength 1300 nm
Nominal Distance 50 km (31.1 mi)
Regulatory Compliance
The RUGGEDCOM SFP1131-1FX50 complies with the following regulatory requirements when installed in Siemens
RUGGEDCOM routers and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883C, Method 3015.4
JEDEC/EIA JESD22-A114-A
Class 2 (2000 V)
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
Bellcore GR1089-CORE 25 kV Air Discharge
10 Zaps at 8 kV (contact discharge) on the
electrical faceplate on panel
Electromagnetic Interference (EMI) FCC Class B Compliant
Immunity Variation of IEC 61000-4-3 Compliant
Eye Safety US FDA CDRH AEL Class 1 Class 1
RUGGEDCOM SFP Transceivers
Catalog
Chapter 3
Fast Ethernet SFP Transceivers
RUGGEDCOM SFP1131-1FX50 15
Feature Standard Performance
IEC/EN 60825-1 and 60825-2
EN 60950 Class 1
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FE53-0AA0 RUGGEDCOM SFP1131-1FX50 100Base-FX SFP – SM, 1300 nm, LC, 50 km
Chapter 3
Fast Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
16 RUGGEDCOM SFP1131-1FX90
Section3.4
RUGGEDCOM SFP1131-1FX90
Siemens' RUGGEDCOM SFP1131-1FX90 industrial grade 100 Mbps fiber optic fast Ethernet SFP transceiver
operates within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Fast
Ethernet communication up to 90 km (55.9 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA for 100Base-FX
• Transmission distance up to 90 km (55.9 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -5 to -0 dBm
Receiver Sensitivity -34 to -10 dBm
Power Budget 29
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 0 to 85% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 100 Mbps
Mode SM (Single-Mode)
Interface FX
Connector LC
Cable Type 9/125 μm
Wavelength 1550 nm
Nominal Distance 90 km (55.9 mi)
Regulatory Compliance
The RUGGEDCOM SFP1131-1FX90 complies with the following regulatory requirements when installed in Siemens
RUGGEDCOM routers and/or switches:
Feature Standard Performance
Laser Eye Safety IEC/EN 60825 Class 1
Electrical Safety IEC/EN 60950 Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FE54-0AA0 RUGGEDCOM SFP1131-1FX90 100Base-FX SFP – SM, 1550 nm, LC, 90 km
RUGGEDCOM SFP Transceivers
Catalog
Chapter 4
Active 100 Mbps SFP Transceivers
17
Active 100 Mbps SFP
Transceivers
The following active 100 Mbps Ethernet SFP transceivers are available from Siemens for select RUGGEDCOM
routers and switches. To determine compatibility, refer to Section1.2, “Available SFP Transceivers”.
CONTENTS
•Section4.1, “RUGGEDCOM SFP1121-1FX2A”
•Section4.2, “RUGGEDCOM SFP1131-1FX10A”
•Section4.3, “RUGGEDCOM SFP1131S-1FX40A”
Chapter 4
Active 100 Mbps SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
18 RUGGEDCOM SFP1121-1FX2A
Section4.1
RUGGEDCOM SFP1121-1FX2A
Siemens' RUGGEDCOM SFP1121-1FX2A industrial grade 100 Mbps fiber optic fast Ethernet SFP transceiver
operates within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Fast
Ethernet communication up to 2 km (1.2 mi) using multi-mode fiber.
NOTE
This SFP transceiver is not recommended for use with IEEE 1588.
Highlights
• Compliant with SFP MSA and IEEE 802.3 for
100Base-FX
• Transmission distance up to 2 km (1.2 mi)
• LC duplex connector optical interface
• Operates with 50/125 μm and 62.5/125 μm multi-
mode fiber
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -20 to -14 dBm
Receiver Sensitivity -31.5 to -8 dBm
Power Budget 11.5 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 5 to 95% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 100 Mbps
Mode MM (Multi-Mode)
Interface FX
Connector LC
Cable Type 50/125 or 62.5/125 μm
Wavelength 1310 nm
Nominal Distance 2 km (1.2 mi)
Regulatory Compliance
The RUGGEDCOM SFP1121-1FX2A meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883E, Method 3015.7 Class 1
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
IEC 61000-4-2
GR-1089-CORE
Compliant
Electromagnetic Interference (EMI) FCC Part 15, Class B Compliant
Laser Eye Safety US FDA 21CFR 1040.10 and 1040.11
IEC/EN 60825-1 and 60825-2
Compliant with Class 1 laser product
RUGGEDCOM SFP Transceivers
Catalog
Chapter 4
Active 100 Mbps SFP Transceivers
RUGGEDCOM SFP1121-1FX2A 19
Feature Standard Performance
RoHS EU RoHS Directive 2011/65/EU Compliant
Ordering Information
Article Number Name Description
6GK6000-8FE50-0AA0 RUGGEDCOM SFP1121-1FX2A 100Base-FX SFP – MM, 1310 nm, LC, 2 km
Chapter 4
Active 100 Mbps SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
20 RUGGEDCOM SFP1131-1FX10A
Section4.2
RUGGEDCOM SFP1131-1FX10A
Siemens' RUGGEDCOMSFP1131-1FX10A industrial grade 100 Mbps fiber optic fast Ethernet SFP transceiver
operates within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Fast
Ethernet communication up to 10 km (6.2 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA for 100Base-FX
• Transmission distance up to 10 km (6.2 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -15 to -8 dBm
Receiver Sensitivity -31.5 to -8 dBm
Power Budget 16.5
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 0 to 85% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 100 Mbps
Interface FX
Mode SM (Single-Mode)
Connector LC
Cable Type 9/125 μm
Wavelength 1310 nm
Nominal Distance 10 km (6.2 mi)
Regulatory Compliance
The RUGGEDCOM SFP1131-1FX10A complies with the following regulatory requirements when installed in
Siemens RUGGEDCOM routers and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883E, Method 3015.7 Class 1
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
IEC 61000-4-2
GR-1089-CORE
Compliant
Electromagnetic Interference (EMI) FCC Part 15, Class B Compliant
Eye Safety US FDA 21CFR 1040.10 and 1040.11
IEC/EN 60825-1 and 60825-2
Compliant with Class 1 laser product
RoHS EU RoHS Directive 2011/65/EU Compliant
RUGGEDCOM SFP Transceivers
Catalog
Chapter 4
Active 100 Mbps SFP Transceivers
RUGGEDCOM SFP1131-1FX10A 21
Ordering Information
Article Number Name Description
6GK6000-8FE60-0AA0 RUGGEDCOM SFP1131-1FX10A 100Base-LX SFP – SM, 1310 nm, LC, 10 km
Chapter 4
Active 100 Mbps SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
22 RUGGEDCOM SFP1131S-1FX40A
Section4.3
RUGGEDCOM SFP1131S-1FX40A
Siemens' RUGGEDCOMSFP1131S-1FX40A industrial grade 100 Mbps fiber optic fast Ethernet SFP transceiver
operates within a wide temperature range (-5 to 70 °C or 23 to 158 °F) and provides high performance Fast
Ethernet communication up to 40 km (24.9 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA for 100Base-FX
• Transmission distance up to 40 km (24.9 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -5 to 0 dBm
Receiver Sensitivity -23 to 0 dBm
Power Budget 18
Environment
Operating Temperature -5 to 70 °C (23 to 158 °F)
Operating Relative Humidity 0 to 85% (non-condensing)
Storage Temperature -5 to 70 °C (23 to 158 °F)
Cabling
Speed 100 Mbps
Interface FX
Mode SM (Single-Mode)
Connector LC
Cable Type 9/125 μm
Wavelength 1310 nm
Nominal Distance 40 km (24.9 mi)
Regulatory Compliance
The RUGGEDCOM SFP1131S-1FX40A complies with the following regulatory requirements when installed in
Siemens RUGGEDCOM routers and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883E, Method 3015.7 Class 1
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
IEC 61000-4-2
GR-1089-CORE
Compliant
Electromagnetic Interference (EMI) FCC Part 15, Class B Compliant
Eye Safety US FDA 21CFR 1040.10 and 1040.11
IEC/EN 60825-1 and 60825-2
Compliant with Class 1 laser product
RoHS EU RoHS Directive 2011/65/EU Compliant
RUGGEDCOM SFP Transceivers
Catalog
Chapter 4
Active 100 Mbps SFP Transceivers
RUGGEDCOM SFP1131S-1FX40A 23
Ordering Information
Article Number Name Description
6GK6000-8FE62-0AA0 RUGGEDCOM SFP1131S-1FX40A 100Base-LX SFP – SM, 1310 nm, LC, 40 km
Chapter 4
Active 100 Mbps SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
24 RUGGEDCOM SFP1131S-1FX40A
RUGGEDCOM SFP Transceivers
Catalog
Chapter 5
Gigabit Ethernet SFP Transceivers
25
Gigabit Ethernet SFP
Transceivers
The following Gigabit Ethernet SFP transceivers are available from Siemens for select RUGGEDCOM routers and
switches. To determine compatibility, refer to Section1.2, “Available SFP Transceivers”.
CONTENTS
•Section5.1, “RUGGEDCOM SFP1122-1SX”
•Section5.2, “RUGGEDCOM SFP1122-1SX2”
•Section5.3, “RUGGEDCOM SFP1132-1LX10”
•Section5.4, “RUGGEDCOM SFP1132-1LX25”
•Section5.5, “RUGGEDCOM SFP1132-1LX40”
•Section5.6, “RUGGEDCOM SFP1132-1LX70”
•Section5.7, “RUGGEDCOM SFP1132-1LX100”
•Section5.8, “RUGGEDCOM SFP1132-1LX115”
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
26 RUGGEDCOM SFP1122-1SX
Section5.1
RUGGEDCOM SFP1122-1SX
Siemens' RUGGEDCOM SFP1122-1SX industrial grade 1 Gbps fiber optic SFP transceiver operates within a wide
temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet communication
up to either 0.5 km (0.3 mi) or 0.3 km (0.2 mi) using multi-mode fiber, depending on the cable type in use.
Highlights
• Compliant with SFP MSA and IEEE 802.3 for
1000Base-SX
• Transmission distance up to 0.5 km (0.3 mi) or 0.3
km (0.2 mi)
• LC duplex connector optical interface
• Operates with 50/125 μm and 62.5/125 μm multi-
mode fiber
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -9 to -2.5 dBm
Receiver Sensitivity -20 to 0 dBm
Power Budget 11 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 5 to 95% (non-condensing)
Storage Temperature -40 to 100 °C (-40 to 212 °F)
Cabling
Speed 1 Gbps
Mode MM (Multi-Mode)
Interface SX
Connector LC
Cable Type 50/125 or 62.5/125 μm
Wavelength 850 nm
Nominal Distance (50/125 μm) 0.5 km (0.3 mi)
Nominal Distance (62.5/125
μm)
0.3 km (0.2 mi)
Regulatory Compliance
The RUGGEDCOM SFP1122-1SX meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Laser Eye Safety IEC/EN 60825 Class 1
Electrical Safety IEC/EN 60950 Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
RUGGEDCOM SFP Transceivers
Catalog
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP1122-1SX 27
Ordering Information
Article Number Name Description
6GK6000-8FG51-0AA0 RUGGEDCOM SFP1122-1SX 1000Base-SX SFP – MM, 850 nm, LC, 0.5 km
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
28 RUGGEDCOM SFP1122-1SX2
Section5.2
RUGGEDCOM SFP1122-1SX2
Siemens' RUGGEDCOM SFP1122-1SX2 industrial grade 1 Gbps fiber optic SFP transceiver operates within a wide
temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet communication
up to 2 km (1.2 mi) using multi-mode fiber.
Highlights
• Compliant with SFP MSA and IEEE 802.3z for
1000Base-SX
• Transmission distance up to 2 km (1.2 mi)
• LC duplex connector optical interface
• Operates with 50/125 μm and 62.5/125 μm multi-
mode fiber
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -9 to 1 dBm
Receiver Sensitivity -23 to -3 dBm
Power Budget 14 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 5 to 85% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode MM (Multi-Mode)
Interface SX
Connector LC
Cable Type 50/125 or 62.5/125 μm
Wavelength 1310 nm
Nominal Distance 2 km (1.2 mi)
Regulatory Compliance
The RUGGEDCOM SFP1122-1SX2 meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Laser Eye Safety IEC/EN 60825 Class 1
Electrical Safety IEC/EN 60950 Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FE58-0AA0 RUGGEDCOM SFP1122-1SX2 1000Base-SX SFP – MM, 1310 nm, LC, 2 km
RUGGEDCOM SFP Transceivers
Catalog
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP1132-1LX10 29
Section5.3
RUGGEDCOM SFP1132-1LX10
Siemens' RUGGEDCOM SFP1132-1LX10 industrial grade 1 Gbps fiber optic long haul SFP transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 10 km (6.2 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA and IEEE 802.3 for 1000Base-LX
• Compliant with SFF-8472 Digital Diagnostic Monitoring Interface
• Transmission distance up to 10 km (6.2 mi)
• LC duplex connector optical interface
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -9.5 to -3.0 dBm
Receiver Sensitivity -19.0 to -3.0 dBm
Power Budget 9.5 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 5 to 95% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode SM (Single-Mode)
Interface LX
Connector LC
Cable Type 9/125 μm
Wavelength 1310 nm
Nominal Distance 10 km (6.2 mi)
Regulatory Compliance
The RUGGEDCOM SFP1132-1LX10 meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883C, Method 3015.4
JEDEC/EIA JESD22-A114-A
Class 2 (> 2000 V)
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
Bellcore GR1089-CORE Compliant
Electromagnetic Interference (EMI) FCC Class B Compliant
Immunity Variation of IEC 61000-4-3 Compliant
Eye Safety US FDA CDRH AEL Class 1
IEC/EN 60825-1 and 60825-2
EN 60950 Class 1
Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
30 RUGGEDCOM SFP1132-1LX10
Ordering Information
Article Number Name Description
6GK6000-8FG52-0AA0 RUGGEDCOM SFP1132-1LX10 1000Base-LX SFP – SM, 1310 nm, LC, 10 km
RUGGEDCOM SFP Transceivers
Catalog
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP1132-1LX25 31
Section5.4
RUGGEDCOM SFP1132-1LX25
Siemens' RUGGEDCOM SFP1132-1LX25 industrial grade 1 Gbps fiber optic long haul SFP transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 25 km (15.5 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA for 1000Base-LX
• Compliant with SFF-8472 Digital Diagnostic Monitoring Interface
• Transmission distance up to 25 km (15.5 mi)
• LC duplex connector optical interface
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -7.0 to -3.0 dBm
Receiver Sensitivity -23.0 to -3.0 dBm
Power Budget 16 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode SM (Single-Mode)
Interface LX
Connector LC
Cable Type 9/125 μm
Wavelength 1310 nm
Nominal Distance 25 km (15.5 mi)
Regulatory Compliance
The RUGGEDCOM SFP1132-1LX25 meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Electromagnetic Interference (EMI) FCC Class B Compliant
Eye Safety IEC/EN 60825-1 Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FG53-0AA0 RUGGEDCOM SFP1132-1LX25 1000Base-LX SFP – SM, 1310 nm, LC, 25 km
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
32 RUGGEDCOM SFP1132-1LX40
Section5.5
RUGGEDCOM SFP1132-1LX40
Siemens' RUGGEDCOM SFP1132-1LX40 industrial grade 1 Gbps fiber optic long haul SFP transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 40 km (24.9 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA for 1000Base-LX
• Compliant with SFF-8472 Digital Diagnostic
Monitoring Interface
• Transmission distance up to 40 km (24.9 mi)
• LC duplex connector optical interface
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -6.0 to 0.0 dBm
Receiver Sensitivity -23.0 to -3.0 dBm
Power Budget 17 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode SM (Single-Mode)
Interface LX
Connector LC
Cable Type 9/125 μm
Wavelength 1550 nm
Nominal Distance 40 km (24.9 mi)
Regulatory Compliance
The RUGGEDCOM SFP1132-1LX40 meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Electromagnetic Interference (EMI) FCC Class B Compliant
Eye Safety IEC/EN 60825-1 Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FG57-0AA0 RUGGEDCOM SFP1132-1LX40 1000Base-LX SFP – SM, 1550 nm, LC, 40 km
RUGGEDCOM SFP Transceivers
Catalog
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP1132-1LX70 33
Section5.6
RUGGEDCOM SFP1132-1LX70
Siemens' RUGGEDCOM SFP1132-1LX70 industrial grade 1 Gbps fiber optic long haul SFP transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 70 km (43.5 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA for 1000Base-LX
• Compliant with SFF-8472 Digital Diagnostic Monitoring Interface
• Transmission distance up to 70 km (43.5 mi)
• LC duplex connector optical interface
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -0.0 to 5.0 dBm
Receiver Sensitivity -23.0 to -3.0 dBm
Power Budget 23 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode SM (Single-Mode)
Interface LX
Connector LC
Cable Type 9/125 μm
Wavelength 1550 nm
Nominal Distance 70 km (43.5 mi)
Regulatory Compliance
The RUGGEDCOM SFP1132-1LX70 meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Electromagnetic Interference (EMI) FCC Class B Compliant
Eye Safety IEC/EN 60825-1 Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FG54-0AA0 RUGGEDCOM SFP1132-1LX70 1000Base-LX SFP – SM, 1550 nm, LC, 70 km
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
34 RUGGEDCOM SFP1132-1LX100
Section5.7
RUGGEDCOM SFP1132-1LX100
Siemens' RUGGEDCOM SFP1132-1LX100 industrial grade 1 Gbps fiber optic long haul SFP transceiver operates
within a wide temperature range (0 to 70 °C or 32 to 158 °F) and provides high performance Gigabit Ethernet
communication up to 100 km (62.1 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA and IEE 802.3 for
1000Base-LX
• Compliant with SFF-8472 Digital Diagnostic
Monitoring Interface
• Transmission distance up to 100 km (62.1 mi)
• LC duplex connector optical interface
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -0.0 to 5.0 dBm
Receiver Sensitivity -30.0 to -8.0 dBm
Power Budgeta30 dB
Environment
Operating Temperature 0 to 70 °C (32 to 158 °F)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode SM (Single-Mode)
Interface LX
Connector LC
Cable Type 9/125 μm
Wavelength 1550 nm
Nominal Distance: 100 km (62.1 mi)
aAssumes the same SFP transceiver is used on both ends of the connection.
Regulatory Compliance
The RUGGEDCOM SFP1132-1LX100 meets the following standards when installed in Siemens RUGGEDCOM
routers and/or switches:
Feature Standard Performance
Electromagnetic Interference (EMI) FCC Class B Compliant
Eye Safety IEC/EN 60825-1 Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FG55-0AA0 RUGGEDCOM SFP1132-1LX100 1000Base-LX SFP – SM, 1550 nm, LC, 100 km
RUGGEDCOM SFP Transceivers
Catalog
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP1132-1LX115 35
Section5.8
RUGGEDCOM SFP1132-1LX115
Siemens' RUGGEDCOM SFP1132-1LX115 industrial grade 1 Gbps fiber optic long haul SFP transceiver operates
within a wide temperature range (-10 to 70 °C or 14 to 158 °F) and provides high performance Gigabit Ethernet
communication up to 115 km (71.5 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA for 1000Base-LX
• Transmission distance up to 115 km (71.5 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power 0 to 5 dBm
Receiver Sensitivity -30 to -9 dBm
Receiver Sensitivity 30 dB
Environment
Operating Temperature -10 to 70 °C (14to 158 °F)
Operating Relative Humidity 0 to 85% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode SM (Single-Mode)
Interface LX
Connector LC
Cable Type 9/125 μm
Wavelength 1550 nm
Nominal Distance 115 km (71.5 mi)
Regulatory Compliance
The RUGGEDCOM SFP1132-1LX115 meets the following standards when installed in Siemens RUGGEDCOM
routers and/or switches:
Feature Standard Performance
Laser Eye Safety IEC/EN 60825 Class 1
Electrical Safety IEC/EN 60950 Compliant
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FE56-0AA0 RUGGEDCOM SFP1132-1LX115 1000Base-LX SFP – SM, 1550 nm, LC, 115 km
Chapter 5
Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
36 RUGGEDCOM SFP1132-1LX115
RUGGEDCOM SFP Transceivers
Catalog
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
37
Bidirectional Gigabit Ethernet
SFP Transceivers
The following Bidrectional (BiDi) SFP transceivers are available from Siemens for select RUGGEDCOM routers and
switches. To determine compatibility, refer to Section1.2, “Available SFP Transceivers”.
CONTENTS
•Section6.1, “RUGGEDCOM SFP1132-1BX10R”
•Section6.2, “RUGGEDCOM SFP1132-1BX10T”
•Section6.3, “RUGGEDCOM SFP1132-1BX40R”
•Section6.4, “RUGGEDCOM SFP1132-1BX40T”
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
38 RUGGEDCOM SFP1132-1BX10R
Section6.1
RUGGEDCOM SFP1132-1BX10R
Siemens' RUGGEDCOM SFP1132-1BX10R industrial grade 1 Gbps fiber optic bi-directional SFP transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 10 km (6.2 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA for 1000BASE-BX10-U
• Compliant with SFF-8472 Digital Diagnostic
Monitoring Interface
• Transmission distance up to 10 km (6.2 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -9.0 to -3.0 dBm
Receiver Sensitivity -19.5 to -3.0 dBm
Power Budgeta10.5 db
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 5 to 95% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1000 Mbit/s
Mode SM
Interface BX
Connector LC
Cable Type (μm) 9/125
Wavelength (Tx) 1310 nm
Wavelength (Rx) 1490 nm
Nominal Distance 10 km (6.2 mi)
aAssumes an SFP1132-1BX10T is used at the other end of the connection.
Regulatory Compliance
The RUGGEDCOM SFP1132-1BX10R meets the following standards when installed in Siemens RUGGEDCOM
routers and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883E, Method 3015.7 Class 1
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
IEC 61000-4-2 Compliant
Electromagnetic Interference (EMI) FCC Part 15, Class B Compliant
Laser Eye Safety US FDA 21CRF 1040.10 and 1040.11
IEC/EN 60825-1 and 60825-2
EN 60950
Compliant with Class 1 laser product
RoHS EU RoHS Directive 2011/65/EU Compliant
RUGGEDCOM SFP Transceivers
Catalog
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP1132-1BX10R 39
Ordering Information
Article Number Name Description
6GK6000-8FB51-0AA0 RUGGEDCOM SFP1132-1BX10R 1000Base-BX SFP – SM, 1310/1490 nm, LC, 10 km
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
40 RUGGEDCOM SFP1132-1BX10T
Section6.2
RUGGEDCOM SFP1132-1BX10T
Siemens' RUGGEDCOM SFP1132-1BX10T industrial grade 1 Gbps fiber optic bi-directional SFP transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 10 km (6.2 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA for 1000BASE-BX10-D
• Compliant with SFF-8472 Digital Diagnostic
Monitoring Interface
• Transmission distance up to 10 km (6.2 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -9.0 to -3.0 dBm
Receiver Sensitivity -19.5 to -3.0 dBm
Power Budgetb10.5 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 5 to 95% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode SM (Single-Mode)
Interface BX
Connector LC
Cable Type 9/125 μm
Wavelength (Tx) 1490 nm
Wavelength (Rx) 1310 nm
Nominal Distance 10 km (6.2 mi)
bAssumes an SFP1132-1BX10R is used at the other end of the connection.
Regulatory Compliance
The RUGGEDCOM SFP1132-1BX10T meets the following standards when installed in Siemens RUGGEDCOM
routers and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883E, Method 3015.7 Class 1
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
IEC 61000-4-2 Compliant
Electromagnetic Interference (EMI) FCC Part 15, Class B Compliant
Laser Eye Safety US FDA 21CRF 1040.10 and 1040.11
IEC/EN 60825-1 and 60825-2
EN 60950
Compliant with Class 1 laser product
RoHS EU RoHS Directive 2011/65/EU Compliant
RUGGEDCOM SFP Transceivers
Catalog
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP1132-1BX10T 41
Ordering Information
Article Number Name Description
6GK6000-8FB52-0AA0 RUGGEDCOM SFP1132-1BX10T 1000Base-BX SFP – SM, 1490/1310 nm, LC, 10 km
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
42 RUGGEDCOM SFP1132-1BX40R
Section6.3
RUGGEDCOM SFP1132-1BX40R
Siemens' RUGGEDCOM SFP1132-1BX40R industrial grade 1 Gbps fiber optic bi-directional SFP transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 40 km (24.9 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA and IEEE 802.3ah for
1000Base-BX40-U
• Compliant with SFF-8472 Digital Diagnostic
Monitoring Interface
• Transmission distance up to 40 km (24.9 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -2.0 to 3.0 dBm
Receiver Sensitivity -23.0 to -3.0 dBm
Power Budgetc21 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 5 to 95% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode SM (Single-Mode)
Interface BX
Connector LC
Cable Type 9/125 μm
Wavelength (Tx) 1310 nm
Wavelength (Rx) 1490 nm
Nominal Distance 40 km (24.9 mi)
cAssumes an SFP1132-1BX40T is used at the other end of the connection.
Regulatory Compliance
The RUGGEDCOM SFP1132-1BX40R meets the following standards when installed in Siemens RUGGEDCOM
routers and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883E, Method 3015.7 Class 1
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
IEC 61000-4-2 Compliant
Electromagnetic Interference (EMI) FCC Part 15, Class B Compliant
Immunity Variation of IEC 61000-4-3 Compliant
Laser Eye Safety US FDA 21CRF 1040.10 and 1040.11
IEC/EN 60825-1 and 60825-2
Compliant with Class 1 laser product
RUGGEDCOM SFP Transceivers
Catalog
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP1132-1BX40R 43
Feature Standard Performance
EN 60950
RoHS EU RoHS Directive 2011/65/EU Compliant
Ordering Information
Article Number Name Description
6GK6000-8FB53-0AA0 RUGGEDCOM SFP1132-1BX40R 1000Base-BX SFP – SM, 1310/1490 nm, LC, 40 km
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
44 RUGGEDCOM SFP1132-1BX40T
Section6.4
RUGGEDCOM SFP1132-1BX40T
Siemens' RUGGEDCOM SFP1132-1BX40T industrial grade 1 Gbps fiber optic bi-directional SFP transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 40 km (24.9 mi) using single-mode fiber.
Highlights
• Compliant with SFP MSA and IEEE 802.3ah for
1000Base-BX-D
• Compliant with SFF-8472 Digital Diagnostic
Monitoring Interface
• Transmission distance up to 40 km (24.9 mi)
• LC duplex fiber connector
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -2.0 to 3.0 dBm
Receiver Sensitivity -23.0 to -3.0 dBm
Power Budgetd21 dB
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 5 to 95% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 1 Gbps
Mode SM (Single-Mode)
Interface BX
Connector LC
Cable Type 9/125 μm
Wavelength (Tx) 1490 nm
Wavelength (Rx) 1310 nm
Nominal Distance 40 km (24.9 mi)
dAssumes an SFP1132-1BX40R is used at the other end of the connection.
Regulatory Compliance
The RUGGEDCOM SFP1132-1BX40T meets the following standards when installed in Siemens RUGGEDCOM
routers and/or switches:
Feature Standard Performance
Electrostatic Discharge (ESD) to the Electrical
Pins
MIL-STD-883E, Method 3015.7 Class 1
Electrostatic Discharge (ESD) to the Duplex
LC Receptacle
IEC 61000-4-2 Compliant
Electromagnetic Interference (EMI) FCC Part 15, Class B Compliant
Immunity Variation of IEC 61000-4-3 Compliant
Laser Eye Safety US FDA 21CRF 1040.10 and 1040.11
IEC/EN 60825-1 and 60825-2
Compliant with Class 1 laser product
RUGGEDCOM SFP Transceivers
Catalog
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP1132-1BX40T 45
Feature Standard Performance
EN 60950
RoHS EU RoHS Directive 2011/65/EU Compliant
Ordering Information
Article Number Name Description
6GK6000-8FB54-0AA0 RUGGEDCOM SFP1132-1BX40T 1000Base-BX SFP – SM, 1490/1310 nm, LC, 40 km
Chapter 6
Bidirectional Gigabit Ethernet SFP Transceivers
RUGGEDCOM SFP Transceivers
Catalog
46 RUGGEDCOM SFP1132-1BX40T
RUGGEDCOM SFP Transceivers
Catalog
Chapter 7
10-Gigabit Ethernet SFP+ Transceivers
47
10-Gigabit Ethernet SFP+
Transceivers
The following 10-Gigabit Ethernet SFP+ transceivers are available from Siemens for select RUGGEDCOM routers
and switches. To determine compatibility, refer to Section1.2, “Available SFP Transceivers”.
CONTENTS
•Section7.1, “RUGGEDCOM SFP2123-1SR”
•Section7.2, “RUGGEDCOM SFP2133-1LR10”
•Section7.3, “RUGGEDCOM SFP2133-1ER40”
•Section7.4, “RUGGEDCOM SFP2133-1ZR80”
Chapter 7
10-Gigabit Ethernet SFP+ Transceivers
RUGGEDCOM SFP Transceivers
Catalog
48 RUGGEDCOM SFP2123-1SR
Section7.1
RUGGEDCOM SFP2123-1SR
Siemens' RUGGEDCOM SFP2123-1SR industrial grade 10 Gbps fiber optic long reach SFP+ transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 400 m (1312 ft) using multi-mode fiber.
Highlights
• Compliant with SFP+ MSA and IEEE 802.3ae for
10GBase-SR
• Compliant with SFF-8431 (Rev 2)
• Compliant with SFF-8432 (Rev 4.3)
• Transmission distance up to 400 m (1312 ft)
• LC duplex connector optical interface
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -5.0 to -1.0 dBm
Tx Typical OMA -1.5
Minimum Extinction Ratio 3.0
Rx Sensitivity OMA (dBm) -11.1
Stressed RX Sensitivity (dBm) -7.5
Rx Saturation (dBm) 0.5
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 0 to 85% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 10 Gbps
Mode MM (Multi-Mode)
Interface SR
Connector LC
Cable Type 50/125 or 62.5/125 μm
Wavelength 850 nm
Nominal Distance 400 m (1312 ft)
Regulatory Compliance
The RUGGEDCOM SFP2123-1SR meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Electromagnetic Interference (EMI) FCC Class B Compliant
Eye Safety US FDA 21CRF 1040.10 and 1040.11
IEC/EN 60825-1
Class 1
RoHS EU RoHS Directive 2002/95/EC Compliant
RUGGEDCOM SFP Transceivers
Catalog
Chapter 7
10-Gigabit Ethernet SFP+ Transceivers
RUGGEDCOM SFP2123-1SR 49
Ordering Information
Article Number Name Description
6GK6000-8FT50-0AA0 RUGGEDCOM SFP2123-1SR 10GBase-SR SFP – SM, 850 nm, LC, 400 m
Chapter 7
10-Gigabit Ethernet SFP+ Transceivers
RUGGEDCOM SFP Transceivers
Catalog
50 RUGGEDCOM SFP2133-1LR10
Section7.2
RUGGEDCOM SFP2133-1LR10
Siemens' RUGGEDCOM SFP2133-1LR10 industrial grade 10 Gbps fiber optic long reach SFP+ transceiver operates
within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit Ethernet
communication up to 10 km (6.2 mi) using single-mode fiber.
Highlights
• Compliant with SFP+ MSA and IEEE 802.3ae for
10GBase-LR/LW
• Compliant with SFF-8431 (Rev 2)
• Compliant with SFF-8432 (Rev 4.3)
• Transmission distance up to 10 km (6.2 mi)
• LC duplex connector optical interface
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -8.2 to 0.5 dBm
Tx Minimum OMA -5.2
Minimum Extinction Ratio 3.5
Rx Sensitivity OMA (dBm) -12.6
Stressed RX Sensitivity (dBm) -10.3
Rx Saturation (dBm) 0.5
Power Budget (dB) 4.4
Channel Insertion Loss (dB) 5.1
Allocation for Penalties (dB) 2.3
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Operating Relative Humidity 0 to 85% (non-condensing)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 10 Gbps
Mode SM (Single-Mode)
Interface LR
Connector LC
Cable Type 9/125 μm
Wavelength 1310 nm
Nominal Distance 10 km (6.2 mi)
Product-Specific Deviations
The RUGGEDCOM SFP2133-1LR10 supports the following ratings when installed in the specified Siemens
RUGGEDCOM routers and/or switches:
Product(s) Specification Rating
RUGGEDCOM RX5000 Operating Temperature -40 to 80 °C (-40 to 176 °F)
RUGGEDCOM MX5000 Operating Temperature -40 to 80 °C (-40 to 176 °F)
RUGGEDCOM SFP Transceivers
Catalog
Chapter 7
10-Gigabit Ethernet SFP+ Transceivers
RUGGEDCOM SFP2133-1LR10 51
Regulatory Compliance
The RUGGEDCOM SFP2133-1LR10 meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
Electromagnetic Interference (EMI) FCC Class B Compliant
Eye Safety US FDA 21CRF 1040.10 and 1040.11
IEC/EN 60825-1
Class 1
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FT51-0AA0 RUGGEDCOM SFP2133-1LR10 10GBase-LR SFP – SM, 1310 nm, LC, 10 km
Chapter 7
10-Gigabit Ethernet SFP+ Transceivers
RUGGEDCOM SFP Transceivers
Catalog
52 RUGGEDCOM SFP2133-1ER40
Section7.3
RUGGEDCOM SFP2133-1ER40
Siemens' RUGGEDCOM SFP2133-1ER40 industrial grade 10 Gbps fiber optic extended reach SFP+ transceiver
operates within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit
Ethernet communication up to 40 km (24.9 mi) using single-mode fiber.
Highlights
• Compliant with SFP+ MSA and IEEE 802.3ae for
10GBase-ER/EW
• Compliant with SFF-8431 (Rev 2)
• Compliant with SFF-8432 (Rev 4.3)
• Compliant with SFF-8472 Digital Diagnostic
Monitoring Interface (Rev 10.4)
• Transmission distance up to 40 km (24.9 mi)
• LC duplex connector optical interface
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -4.4 to 4.0 dBm
Tx Minimum OMA -1.7
Minimum Extinction Ratio 8.2
Rx Sensitivity OMA (dBm) -14.1
Stressed RX Sensitivity (dBm) -11.3
Rx Saturation (dBm) -1.0
Power Budget (dB) 9.4
Channel Insertion Loss (dB) 10.9
Allocation for Penalties (dB) 4.1
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 10 Gbps
Mode SM (Single-Mode)
Interface ER
Connector LC
Cable Type 9/125 μm
Wavelength 1550 nm
Nominal Distance 40 km (24.9 mi)
Regulatory Compliance
The RUGGEDCOM SFP2133-1ER40 meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
RoHS EU RoHS Directive 2002/95/EC Compliant
RUGGEDCOM SFP Transceivers
Catalog
Chapter 7
10-Gigabit Ethernet SFP+ Transceivers
RUGGEDCOM SFP2133-1ER40 53
Ordering Information
Article Number Name Description
6GK6000-8FT53-0AA0 RUGGEDCOM SFP2133-1ER40 10GBase-ER SFP – SM, 1550 nm, LC, 40 km
Chapter 7
10-Gigabit Ethernet SFP+ Transceivers
RUGGEDCOM SFP Transceivers
Catalog
54 RUGGEDCOM SFP2133-1ZR80
Section7.4
RUGGEDCOM SFP2133-1ZR80
Siemens' RUGGEDCOM SFP2133-1ZR80 industrial grade 10 Gbps fiber optic extended reach SFP+ transceiver
operates within a wide temperature range (-40 to 85 °C or -40 to 185 °F) and provides high performance Gigabit
Ethernet communication up to 80 km (49.7 mi) using single-mode fiber.
Highlights
• Compliant with SFP+ MSA and OC-192/STM-64 for
10GBase-ZR/ZW
• Compliant with SFF-8431 (Rev 2)
• Compliant with SFF-8432 (Rev 4.3)
• Compliant with SFF-8472 Digital Diagnostic
Monitoring Interface (Rev 10.4)
• Transmission distance up to 80 km (49.7 mi)
• LC duplex connector optical interface
• Bail latch
• Hot swappable
• RoHS compliant
Specifications
Optical Characteristics
Transmit Power -1.0 to 4.0 dBm
Minimum Extinction Ratio 9.0
Rx Sensitivity OMA (dBm) -23.0
Rx Saturation (dBm) -7.0
Power Budget (dB) 22.0
Environment
Operating Temperature -40 to 85 °C (-40 to 185 °F)
Storage Temperature -40 to 85 °C (-40 to 185 °F)
Cabling
Speed 10 Gbps
Mode SM (Single-Mode)
Interface ZR
Connector LC
Cable Type 9/125 μm
Wavelength 1550 nm
Nominal Distance 80 km (49.7 mi)
Regulatory Compliance
The RUGGEDCOM SFP2133-1ZR80 meets the following standards when installed in Siemens RUGGEDCOM routers
and/or switches:
Feature Standard Performance
RoHS EU RoHS Directive 2002/95/EC Compliant
Ordering Information
Article Number Name Description
6GK6000-8FT52-0AA0 RUGGEDCOM SFP2133-1ZR80 10GBase-ZR SFP – SM, 1550 nm, LC, 80 km
RUGGEDCOM SFP Transceivers
Catalog
Chapter 8
Installation/Removal
55
Installation/Removal
All SFP transceivers are hot swappable, making it possible to install or remove them while the router/switch is in
operation.
IMPORTANT!
SFP transceivers can only be hot swapped with SFPs supported by the router/switch. To determine
compatibility, refer to Section1.2, “Available SFP Transceivers”.
CONTENTS
•Section8.1, “Handling SFP Transceivers”
•Section8.2, “Required Tools”
•Section8.3, “Installation”
•Section8.4, “Removal”
Chapter 8
Installation/Removal
RUGGEDCOM SFP Transceivers
Catalog
56 Handling SFP Transceivers
Section8.1
Handling SFP Transceivers
Before handling an SFP transceiver, note the following:
WARNING!
Radiation hazard – risk of serious personal injury. SFP transceivers are equipped with a Class 1 laser.
When installed, each SFP emits invisible radiation even when a cable is not connected. Avoid exposure
to laser radiation and do not stare into open SFP ports.
CAUTION!
Electrical hazard – risk of damage to equipment. Use only components certified by Siemens with
RUGGEDCOM products. Damage to the router/switch may occur if compatibility and reliability have not
been properly assessed.
CAUTION!
Static electricity hazard – risk of damage to equipment. SFP transceivers are sensitive to static
electricity. An electrostatic discharge (ESD) can cause serious damage to the component once it is
outside the chassis. Make sure to wear an ESD-preventive wrist strap connected to the chassis to
prevent an electrostatic discharge (ESD).
CAUTION!
Dirt/debris hazard – risk of damage to equipment. SFP transceivers and sockets are sensitive to the
ingress of dirt/debris. Always install a dust plug in both the SFP transceiver and the socket on the
router/switch after removing the SFP. Do not remove the plugs until inserting the SFP.
CAUTION!
Mechanical hazard – risk of damage to equipment. Do not install/remove SFP transceivers more than
necessary. Repeated installation/removal can reduce the life of the transceiver.
IMPORTANT!
Only permit trained and qualified personnel to install and remove SFP transceivers.
RUGGEDCOM SFP Transceivers
Catalog
Chapter 8
Installation/Removal
Required Tools 57
Section8.2
Required Tools
The following tools are required for installing/removing SFP transceivers:
• An ESD-preventive wrist trap or other personal grounding device
• An anti-static mat or foam to set the transceiver on
Chapter 8
Installation/Removal
RUGGEDCOM SFP Transceivers
Catalog
58 Installation
Section8.3
Installation
To install an SFP transceiver, do the following:
WARNING!
Explosion hazard – risk of serious personal injury and/or equipment damage. Do not install or remove
SFP transceivers when an explosive atmosphere is present.
IMPORTANT!
Only install SFP transceivers that are compatible with the RUGGEDCOM router/switch. For information
about which RUGGEDCOM routers/switches are compatible with an SFP transceiver, refer to
Section1.2, “Available SFP Transceivers”.
1. Make sure all potential electrostatic build-up has been properly discharged to prevent an electrostatic
discharge (ESD). This can be accomplished by wearing an ESD-preventive wrist trap connected to either the
chassis ground connector or a bare metal surface on the router/switch.
2. Remove the SFP transceiver from its packaging.
CAUTION!
Mechanical hazard – risk of component damage. SFP transceivers are designed to insert in only
one orientation. Do not force the SFP transceiver into the socket.
3. Remove the dust plug from the socket and store for future use.
4. Insert the SFP transceiver into the socket, and then swing the bail-latch on the SFP transceiver up and push it
in to lock the transceiver in place.
2
1
Figure1:Installing an SFP Transceiver (Typical)
1.SFP Transceiver 2.Bail-Latch
IMPORTANT!
Only remove the dust plug when ready to connect a cable to the SFP transceiver.
5. Remove the dust plug from the SFP transceiver and store for future use.
6. Remove the dust cap from the cable and immediately connect it to the SFP transceiver.
7. Connect the cable to a network and observe the LED associated with the SFP transceiver.
State Description
Green (Solid) Link established
Green (Blinking) Link activity
RUGGEDCOM SFP Transceivers
Catalog
Chapter 8
Installation/Removal
Installation 59
State Description
Off No link detected
Chapter 8
Installation/Removal
RUGGEDCOM SFP Transceivers
Catalog
60 Removal
Section8.4
Removal
To remove an SFP transceiver, do the following:
WARNING!
Explosion hazard – risk of serious personal injury and/or equipment damage. Do not install or remove
SFP transceivers when an explosive atmosphere is present.
1. Make sure all potential electrostatic build-up has been properly discharged to prevent an electrostatic
discharge (ESD). This can be accomplished by wearing an ESD-preventive wrist trap connected to either the
chassis ground connector or a bare metal surface on the router/switch.
2. Disconnect the cable from the SFP transceiver and install the dust cap to the cable end.
3. Pull the bail-latch out and down on the SFP transceiver, and then immediately insert a dust plug into the SFP
transceiver port.
4. Remove the transceiver from the socket and then immediately insert a dust plug into the socket.
2
1
Figure2:Removing an SFP Transceiver (Typical)
1.SFP Transceiver 2.Bail-Latch
NOTE
Refer to the specifications for the specific SFP transceiver to determine the required storage
temperature range.
5. Store the SFP port in an ESD-safe bag or other suitable ESD-safe environment, free from moisture and stored
at the proper temperature.
6. Insert a dust plug into the socket opening to prevent the ingress of dust and dirt.