Document Number: 82176 www.vishay.com
Rev. 2.3, 20-Aug-10 1
IR Receiver Modules for Remote Control Systems
TSOP61.., TSOP63..
Vishay Semiconductors
MECHANICAL DATA
Pinning
1 = GND, 2 = N.C., 3 = VS, 4 = OUT
DESCRIPTION
The TSOP61.., TSOP63.. series are miniaturized SMD-IR
receivers for infrared remote control systems. A PIN diode
and a preamplifier are assembled on a lead frame, the epoxy
package acts as an IR filter.
The demodulated output signal can directly be decoded by
a microprocessor. The main benefit of the TSOP61.. is the
compatibility to all IR remote control data formats. The
TSOP63.. is optimized to better suppress spurious pulses
from fluorescent lamps, LCD TVs or plasma displays.
This component has not been qualified according to
automotive specifications.
FEATURES
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Continuous data transmission possible
• Supply voltage: 2.7 V to 5.5 V
• Output active low
• Low power consumption
• Compliant to RoHS directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
SPECIAL FEATURES
• Operation with short burst possible (≥ 6 cycles/burst)
• Taping available for topview and sideview assembly
• Enhanced data rate up to 4000 bit/s (TSOP61..)
• Enhanced suppression of noise from fluorescent lamps,
LCD TVs or plasma TVs (TSOP63..)
BLOCK DIAGRAM APPLICATION CIRCUIT
16797
1234
PARTS TABLE
CARRIER FREQUENCY SHORT BURSTS AND HIGH DATA RATES
(AGC1)
NOISY ENVIRONMENTS AND SHORT BURSTS
(AGC3)
30 kHz TSOP6130 TSOP6330
33 kHz TSOP6133 TSOP6333
36 kHz TSOP6136 TSOP6336
36.7 kHz TSOP6137 TSOP6337
38 kHz TSOP6138 TSOP6338
40 kHz TSOP6140 TSOP6340
56 kHz TSOP6156 TSOP6356
3
1
4
16838-1
Input AGC Band
pass
Demo-
dulator
Control circuit
PIN
33 kΩ
VS
OUT
GND
C1
IR receiver
GND
Circuit
µC
R
1
+ V
S
GND
Transmitter
with
TSALxxxx V
S
V
O
17170_7
OUT
The external components R
1
and C
1
are optional
to improve the robustness against electrical overstress
(typical values are R
1
= 100 Ω, C
1
= 0.1 µF).
The output voltage V
O
should not be pulled down to a level
below 1 V by the external circuit.
The capacitive load at the output should be less than 2 nF.
www.vishay.com Document Number: 82176
2Rev. 2.3, 20-Aug-10
TSOP61.., TSOP63..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
ABSOLUTE MAXIMUM RATINGS
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
Supply voltage (pin 3) VS- 0.3 to + 6 V
Supply current (pin 3) IS5mA
Output voltage (pin 4) VO- 0.3 to 5.5 V
Voltage at output to supply VS - VO- 0.3 to (VS + 0.3) V
Output current (pin 4) IO5mA
Junction temperature Tj100 °C
Storage temperature range Tstg - 40 to + 100 °C
Operating temperature range Tamb - 25 to + 85 °C
Power consumption Tamb ≤ 85 °C Ptot 10 mW
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Supply current (pin 3) Ev = 0, VS = 5 V ISD 0.65 0.85 1.05 mA
Ev = 40 klx, sunlight ISH 0.95 mA
Supply voltage VS2.7 5.5 V
Transmission distance
Ev = 0, test signal see fig. 1,
IR diode TSAL6200,
IF = 400 mA
d40m
Output voltage low (pin 4) IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1 VOSL 100 mV
Minimum irradiance
Pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Ee min. 0.3 0.45 mW/m2
Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1 Ee max. 30 W/m2
Directivity Angle of half transmission
distance ϕ1/2 ± 50 deg
Ee
T
tpi *)
t
VO
VOH
VOL tpo 2) t
14337
Optical Test Signal
(IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = fO, t = 10 ms)
Output Signal
td 1)
1) 3/fO < td < 9/fO
2) tpi - 4/fO < tpo < tpi + 6/fO
*) tpi ≥ 6/fo is recommended for optimal function
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.1 1 10 102103104105
E
e
- Irradiance (mW/m²)
t
po
- Output Pulse Width (ms)
21391_1
Output Pulse Width
Input Burst Length
λ = 950 nm,
Optical Test Signal, Fig.1
Document Number: 82176 www.vishay.com
Rev. 2.3, 20-Aug-10 3
TSOP61.., TSOP63..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
Fig. 3 - Output Function
Fig. 4 - Output Pulse Diagram
Fig. 5 - Frequency Dependence of Responsivity
Fig. 6 - Sensitivity in Bright Ambient
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
Fig. 8 - Sensitivity vs. Electric Field Disturbances
E
e
t
V
O
V
OH
V
OL
t
600 µs 600 µs
t = 60 ms
t
on
t
off
94 8134
Optical Test Signal
Output Signal, (see fig. 4)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.1 1 10 102103104105
E
e
- Irradiance (mW/m²)
T
on
, T
off
- Output Pulse Width (ms)
21392_1
T
on
T
off
λ = 950 nm,
Optical Test Signal, Fig. 3
0.0
0.2
0.4
0.6
0.8
1.0
1.2
0.7 0.9 1.1 1.3
f/f
0
- Relative Frequency
16926
f (3 dB) = f
0
/7
E
e min.
/E
e
- Rel. Responsivity
f = f
0
± 5 %
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0.01 0.1 1 10 100
Ee - Ambient DC Irradiance (W/m2)
Ee min. - Threshold Irradiance (mW/m2)
Correlation with Ambient Light Sources:
10 W/m2 = 1.4 kLx (Std. illum. A, T = 2855 K)
10 W/m2 = 8.2 kLx (Daylight, T = 5900 K)
Wavelength of Ambient
Illumination: λ = 950 nm
21393
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1 10 100 1000
ΔVsRMS - AC Voltage on DC Supply Voltage (mV)
21394
Ee min. - Threshold Irradiance (mW/m2)
f = f0
f = 20 kHz
f = 30 kHz
f = 100 Hz
f = 10 kHz
0
50
100
150
200
250
300
350
400
450
500
0 500 1000 1500 2000 2500 3000
f - EMI Frequency (MHz)
E - Max. Field Strength (V/m)
20747
www.vishay.com Document Number: 82176
4Rev. 2.3, 20-Aug-10
TSOP61.., TSOP63..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length
Fig. 10 - Sensitivity vs. Ambient Temperature
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
Fig. 12 - Horizontal Directivity
Fig. 13 - Sensitivity vs. Supply Voltage
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
0 20 40 60 80 100 120 140
Burst Length (number of cycles/burst)
Max. Envelope Duty Cycle
21590-4
Ee = 2 mW/m²
TSOP61..
TSOP63..
Tamb - Ambient Temperature (°C)
Ee min. - Threshold Irradiance (mW/m2)
21397
0.15
0.2
0.25
0.3
0.35
0.4
0.45
- 30 - 10 10 30 50 70 90
0.0
0.2
0.4
0.6
0.8
1.0
1.2
750 850 950 1050 1150
λ- Wavelength (nm)16919
S ( ) - Relative Spectral Sensitivityλrel
0.20
0.25
0.30
0.35
0.40
0.45
0.50
1.5 2.5 3.5 4.5 5.5234 5
VS - Supply Voltage (V)
Ee min. - Sensitivity (mW/m2)
21398
Document Number: 82176 www.vishay.com
Rev. 2.3, 20-Aug-10 5
TSOP61.., TSOP63..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
SUITABLE DATA FORMAT
The TSOP61.., TSOP63.. series are designed to suppress
spurious output pulses due to noise or disturbance signals.
Data and disturbance signals can be distinguished by the
devices according to carrier frequency, burst length and
envelope duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the TSOP61.., TSOP63.. in
the presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance
signals which are suppressed are:
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
• Modulated IR signals from common fluorescent lamps
(example of noise pattern is shown in fig. 14 or fig. 15)
Fig. 14 - IR Signal from Fluorescent Lamp
with Low Modulation
Fig. 15 - IR Signal from Fluorescent Lamp
with High Modulation
Note
• For data formats with long bursts (10 carrier cycles or longer) we recommend the TSOP62.., TSOP 64.. because of the better noise
suppression.
0101520
Time (ms)
16920
IR Signal
IR Signal from Fluorescent
Lamp with Low Modulation
5
0101520
Time (ms)
16921
IR Signal
IR Signal from Fluorescent
Lamp with High Modulation
5
TSOP61.. TSOP63..
Minimum burst length 6 cycles/burst 6 cycles/burst
After each burst of length
a minimum gap time is required of
6 to 70 cycles
≥ 10 cycles
6 to 35 cycles
≥ 10 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
70 cycles
> 1.1 x burst length
35 cycles
> 6 x burst length
Maximum number of continuous short bursts/second 2000 2000
Recommended for NEC code yes yes
Recommended for RC5/RC6 code yes yes
Recommended for Sony code yes yes
Recommended for RECS-80 code yes yes
Recommended for RCMM code yes yes
Recommended for r-step code yes yes
Recommended for XMP code yes yes
Suppression of interference from fluorescent lamps Common disturbance signals are
supressed (e.g. waveform of figure 14)
Even critical disturbance signals are
suppressed (e.g. waveform of figure 15)
www.vishay.com Document Number: 82176
6Rev. 2.3, 20-Aug-10
TSOP61.., TSOP63..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
PACKAGE DIMENSIONS in millimeters
ASSEMBLY INSTRUCTIONS
Reflow Soldering
• Reflow soldering must be done within 72 h while stored
under a max. temperature of 30 °C, 60 % RH after opening
the dry pack envelope
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as
shown in the diagram. Excercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
• Handling after reflow should be done only after the work
surface has been cooled off
Manual Soldering
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Finish soldering within 3 s
• Handle products only after the temperature has cooled off
2.35
R 1.7
5.51
0.5 ± 0.15
3 x 1.27 = 3.81
2.6
7.5
7.2
4x
1.27
5.3
2.9
4
2.2
Pick and place area. TR taping
2.2
3 x 1.27 = 3.81
1.27 0.9
2.8
specifications
according to DIN
technical drawings
Not indicated tolerances ± 0.3
Pick and place area. TT taping
Footprint
(1.5)
(1.4)
Issue: 8; 02.09.09
16776
Drawing-No.: 6.544-5341.01-4
A
A
0.1
0.1
0.3
0.4
14
Document Number: 82176 www.vishay.com
Rev. 2.3, 20-Aug-10 7
TSOP61.., TSOP63..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
TAPING VERSION TSOP..TT Dimensions in millimeters
0
50
100
150
200
250
300
0 50 100 150 200 250 300
t (s)
T (°C)
255 °C
240 °C 245 °
C
max. 260 °C
max. 120 s max. 100 s
217 °C
max. 20 s
max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s
max. 2 cycles allowed
19800
16584
www.vishay.com Document Number: 82176
8Rev. 2.3, 20-Aug-10
TSOP61.., TSOP63..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
TAPING VERSION TSOP..TR Dimensions in millimeters
16585
Document Number: 82176 www.vishay.com
Rev. 2.3, 20-Aug-10 9
TSOP61.., TSOP63..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
REEL DIMENSIONS in millimeters
LEADER AND TRAILER Dimensions in millimeters
COVER TAPE PEEL STRENGTH
According to DIN EN 60286-3
0.1 N to 1.3 N
300 ± 10 mm/min.
165° to 180° peel angle
LABEL
Standard bar code labels for finished goods
The standard bar code labels are product labels and used
for identification of goods. The finished goods are packed in
final packing area. The standard packing units are labeled
with standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
16734
Trailer Leader
no devices
min.
200
min. 400
StartEnd
devices
96 11818
no devices
www.vishay.com Document Number: 82176
10 Rev. 2.3, 20-Aug-10
TSOP61.., TSOP63..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
DRY PACKING
The reel is packed in an anti-humidity bag to protect the
devices from absorbing moisture during transportation and
storage.
FINAL PACKING
The sealed reel is packed into a cardboard box. A secondary
cardboard box is used for shipping purposes.
RECOMMENDED METHOD OF STORAGE
Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are
not available:
• Storage temperature 10 °C to 30 °C
• Storage humidity ≤ 60 % RH max.
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
In case of moisture absorption, the devices will recover to
the former condition by drying under the following condition:
192 h at 40 °C + 5 °C/ - 0 °C and < 5 % RH (dry air/nitrogen)
or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers
or
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC standard JESD22-A112 level 4 label is
included on all dry bags.
Example of JESD22-A112 level 4 label
VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITING ABBREVIATION LENGTH
Item-description - 18
Item-number INO 8
Selection-code SEL 3
LOT-/serial-number BATCH 10
Data-code COD 3 (YWW)
Plant-code PTC 2
Quantity QTY 8
Accepted by ACC -
Packed by PCK -
Mixed code indicator MIXED CODE -
Origin xxxxxxx+ Company logo
LONG BAR CODE TOP TYPE LENGTH
Item-number N 8
Plant-code N 2
Sequence-number X 3
Quantity N 8
Total length - 21
SHORT BAR CODE BOTTOM TYPE LENGTH
Selection-code X 3
Data-code N 3
Batch-number X 10
Filter - 1
Total length - 17
16943
Document Number: 82176 www.vishay.com
Rev. 2.3, 20-Aug-10 11
TSOP61.., TSOP63..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
ESD PRECAUTION
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electro-static
sensitive devices warning labels are on the packaging.
VISHAY SEMICONDUCTORS STANDARD
BAR CODE LABELS
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
16962
Document Number: 91000 www.vishay.com
Revision: 18-Jul-08 1
Disclaimer
Legal Disclaimer Notice
Vishay
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.