Item no.: SPECIFICATION T60404-N4646-X763 V A C U U M S C H M E LZ E K-no.: 26077 03.07.2012 Date: 6 A Current Sensor for 5V- Supply Voltage For electronic current measurement: DC, AC, pulsed, mixed ..., with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Customer: Customers Part no.: Standard type Page 1 of 2 Description Characteristics Applications * Closed loop (compensation) Current Sensor with magnetic field probe * Printed circuit board mounting * Casing and materials UL-listed * Excellent accuracy * Very low offset current * Very low temperature dependency and offset current drift * Very low hysteresis of offset current * Short response time * Wide frequency bandwidth * Compact design * Reduced offset ripple Mainly used for stationary operation in industrial applications: * AC variable speed drives and servo motor drives * Static converters for DC motor drives * Battery supplied applications * Switched Mode Power Supplies (SMPS) * Power Supplies for welding applications * Uninterruptible Power Supplies (UPS) Electrical data - Ratings IPN Vout Vout VRef Primary nominal r.m.s. current Output voltage @ IP Output voltage @ IP=0, TA=25C External Reference voltage range Internal Reference voltage Turns ratio KN Accuracy - Dynamic performance data IP,max X L Vout - VRef Vo / VRef / T tr t (IP,max) f min. Max. measuring range 20 Accuracy @ IPN, TA= 25C Linearity Offset voltage @ IP=0, TA= 25C Temperature drift of Vout @ IP=0, VRef =2,5V, TA= -40...85C Response time @ 90% von IPN Delay time at di/dt = 100 A/s Frequency bandwidth DC...200 General data min. -40 -40 typ. 10 300 200 typ. 6 VRef (0.625*IP/IPN) VRef 0.0056 0...4 2.5 0.005 1...4 : 2000 A V V V V max. Unit 0.7 0.1 6.5 30 max. +85 +105 % % mV ppm/C ns ns kHz Unit C C g V mA TA TS m VC IC Ambient operating temperature Ambient storage temperature Mass Supply voltage Current consumption Sclear Screep Vsys Vwork UPD Constructed and manufactored and tested in accordance with EN 61800-5-1 (Pin 1 - 4 to Pin 5 - 12) Reinforced insulation, Insulation material group 1, Pollution degree 2 Clearance (component without solder pad) 9.6 mm Creepage (component without solder pad) 10.6 mm System voltage overvoltage category 3 RMS 600 V Working voltage RMS 1060 V Rated discharge voltage peak value 1320 V Date Hrsg.: editor Name KB-E Issue 81 4.75 12 5 15 5.25 Amendment Bearb: Le KB-PM: KRe. check designer Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden Any offenders are liable to pay all relevant damages. freig.: HS released Item no.: SPECIFICATION T60404-N4646-X763 V A C U U M S C H M E LZ E K-no.: 26077 03.07.2012 Date: 6 A Current Sensor for 5V- Supply Voltage For electronic current measurement: DC, AC, pulsed, mixed ..., with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Customer: Customers Part no.: Standard type Mechanical outline (mm): Page General tolerances DIN ISO 2768-c 12 2 of Connections: 1...4: 0,46*0,46 mm 5..12: 1 mm 9 1 13,7 12,7 3x1,905 4 2,54 5 10,16 Marking: 8 7,62 22,2 4646X763 F DC test dimension DC F Tolerances grid distance 0,2mm 24 0,5 +0,1 -0 DC= Date Code F = Factory 3,50,5 Schematic diagram 680 4 VC 1 V ref IN / OUT 2 Iout 3 GND int REF Ip 5...8 40k 10k + + RM OUT 10k 40k 9...12 Possibilities of wiring primary windings (@ TA = 85C) primary current RMS maximal output voltage RMS turns ratio primary resistance NP IP [A] IP,max [A] Vout (IP) [V] KN RP [m ] 1 6 20 2.50.625 1:2000 0.25 wiring 12 9 . . 2 3 10 2.50.625 2:2000 2 6,7 2.50.625 4:2000 8 9 5 12 8 9 5 12 8 5 1.0 . 4 4 . Operating temperature of the current sensor and the primary conductor must not exceed 105C. Additional information is obtainable on request. This specification is no declaration of warranty acc. BGB 443 dar. Hrsg.: editor KB-E Bearb: Le 2 KB-PM: KRe. check designer Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden Any offenders are liable to pay all relevant damages. freig.: HS released Additional Information Item No.: T60404-N4646-X763 V A C U U M S C H M E LZ E K-No.: 26077 6 A Current Sensor for 5V-Supply Voltage Date: 03.07.2012 For the electronic measurement of currents: DC, AC, pulsed, mixed ..., with a galvanic Isolation between the primary circuit (high power) and the secondary circuit Customer: Customers Part No.: Page 1 of 2 Electrical Data VCtot IC Iout,SC RP RS Ri,Ref Ri,(Vout) RL CL XTi / T V0 = (Vout -VRef) V0t V0T V0H V0/VC voss voss voss Ck min. typ. max. Maximum supply voltage (without function) 6 Supply Current with primary current 15mA +Ip*KN+Vout/RL Short circuit output current 20 Resistance / primary winding @ TA=25C 1 Secondary coil resistance @ TA=85C 67 Internal resistance of Reference input 670 Output resistance of Vout 1 External recommended resistance of Vout 1 External recommended capacitance of Vout 500 Temperature drift of X @ TA = -40 ... +85 C 40 Sum of any offset drift including: 5 15 Longtermdrift of V0 3 Temperature drift von V0 @ TA = -40 ...+85C 3 Hysteresis of Vout @ IP=0 (after an overload of 10 x IPN) 7.5 Supply voltage rejection ratio 1 Offsetripple (with 1 MHz- filter first order) 55 Offsetripple (with 100 kHz- filter firdt order) 9 15 Offsetripple (with 20 kHz- filter first order) 2.5 4 Maximum possible coupling capacity (primary - secondary) 5 10 Mechanical stress according to M3209/3 30g Settings: 10 - 2000 Hz, 1 min/Decade, 2 hours Unit V mA mA m k pF ppm/ mV mV mV mV mV/V mV mV mV pF Inspection (Measurement after temperature balance of the samples at room temperature; SC = significant characteristic) Vout (IP=IPN) (V) M3011/6: Vout-VRef (IP=0) (V) M3226: Vd (V) M3014: (AQL 1/S4) Ve Output voltage vs. external reference (IP=6A, 40-80Hz) Offset voltage Test voltage, rms, 1 s pin 1 - 4 vs. pin 5 - 12 Partial discharge voltage acc.M3024 (RMS) with Vvor (RMS) 6250,7% 0.0056 1.8 mV (SC) V kV 1400 1750 V V Type Testing (Pin 1 - 4 to Pin 5 - 12) VW Vd Ve HV transient test according to M3064 (1,2 s / 50 s-wave form) Testing voltage to M3014 (5 s) Partial discharge voltage acc.M3024 (RMS) with Vvor (RMS) 8 3.6 1400 1750 kV kV V V Applicable documents Current direction: A positive output current appears at point IS, by primary current in direction of the arrow. Housing and bobbin material UL-listed: Flammability class 94V-0. Enclosures according to IEC529: IP50. Datum Hrsg.: editor Name KB-E Index 81 Amendment Bearb: Le. KB-PM: KRe. check designer Weitergabe sowie Vervielfaltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrucklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte fur den Fall der Patenterteilung oder GM-Eintragung vorbehalten freig.: HS released Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden. Any offenders are liable to pay all relevant damages. Additional Information Item No.: T60404-N4646-X763 V A C U U M S C H M E LZ E K-No.: 26077 Date: 6 A Current Sensor for 5V-Supply Voltage 03.07.2012 For the electronic measurement of currents: DC, AC, pulsed, mixed ..., with a galvanic Isolation between the primary circuit (high power) and the secondary circuit Customer: Customers Part No.: Page 2 of 2 Explanation of several of the terms used in the tablets (in alphabetical order) tr : Response time (describe the dynamic performance for the specified measurement range), measured as delay time . at IP = 0,9 IPN between a rectangular current and the output voltage VOUt (Ip) t (IPmax): Delay time (describe the dynamic performance for the rapid current pulse rate e.g short circuit current) measured between IPmax and the output voltage Vout(IPmax) with a primary current rise of diP/dt 100 A/s. V0 : Offset voltage between Vout and the rated reference voltage of Vref = 2,5V. Vo = Vout(0) - 2,5V UPD Rated discharge voltage (recurring peak voltage separated by the insulation) proved with a sinusoidal voltage Ve UPD = 2 * Ve / 1,5 Vvor Defined voltage is the RMS valve of a sinusoidal voltage with peak value of 1,875 * UPD required for partial discharge test in IEC 61800-5-1 Vvor = 1,875 *UPD / 2 Vsys System voltage RMS value of rated voltage according to IEC 61800-5-1 Vwork Working voltage voltage according to IEC 61800-5-1 which occurs by design in a circuit or across insulation V0H: Zero variation of Vo after overloading with a DC of tenfold the rated value V0t: Long term drift of Vo after 100 temperature cycles in the range -40 bis 85 C. X: Permissible measurement error in the final inspection at RT, defined by X = 100 Xges(IPN): % Permissible measurement error including any drifts over the temperature range by the current measurement IPN X ges = 100 L : Vout ( I PN ) - Vout (0) -1 0,625V Vout (I PN ) - 2,5V -1 0,625V Linearity fault defined by % L = 100 or X ges = 100 Vout (I PN ) - Vref 0,625V V ( I ) - Vout (0) IP - out P I PN Vout ( I PN ) - Vout (0) -1 % % This "Additional information" is no declaration of warranty according BGB $443. Hrsg.: editor KB-E Bearb: Le. KB-PM: KRe. check designer Weitergabe sowie Vervielfaltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrucklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte fur den Fall der Patenterteilung oder GM-Eintragung vorbehalten freig.: HS released Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden. Any offenders are liable to pay all relevant damages. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Vacuumschmelze: T60404-N4646-X763