DRV1100UG4 - Texas Instruments

DRV1100

In+

In–

Out+

+5V

G = 3V/V

DRV1100

Patent

Pending

GND

Out–

4Ω

4ΩProtection

1:4

Transformer

135Ω

HIGH POWER DIFFERENTIAL DRIVER AMPLIFIER

OPA658

DRV1100

International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111

Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132

DESCRIPTION

The DRV1100 is fixed gain differential line driver

designed for very low harmonic distortion at the high

powers required of xDSL line interface standards.

Operating on a single +5V supply, it can deliver

230mA peak output current and 9.5Vp-p differential

output voltage swing. This high output power on a

single +5V supply makes the DRV1100 an excellent

choice for the xDSL applications that require up to

17dBm power onto the line with high crest factors.

The DRV1100 is available in both 8-pin plastic DIP

and SO-8 packages.

FEATURES

●HIGH OUTPUT CURRENT: 230mA

●SINGLE SUPPLY OPERATION: 5V

●5MHz BANDWIDTH: 6Vp-p into 15Ω

●VERY LOW THD AT HIGH POWER:

–72dBc at 6Vp-p, 100kHz, 100Ω

●LOW QUIESCENT CURRENT: 11mA

●FIXED DIFFERENTIAL GAIN: 3V/V

APPLICATIONS

●xDSL TWISTED PAIR LINE DRIVER

●COMMUNICATIONS LINE DRIVER

●TRANSFORMER DRIVER

●SOLENOID DRIVER

●HIGH POWER AUDIO DRIVER

●CRT YOKE DRIVER

SBWS004

DRV1100

DRV1100P, U

PARAMETER CONDITIONS MIN TYP MAX UNITS

AC PERFORMANCE

–3dB Bandwidth RL = 15Ω, VO = 1Vp-p 8 MHz

RL ≥ 100Ω, VO = 1Vp-p 11 MHz

RL = 15Ω, VO = 6Vp-p 5 MHz

RL ≥ 100Ω, VO = 6Vp-p 6 MHz

Differential Slew Rate RL = 100Ω, VO = 6Vp-p 80 V/µs

Step Response Delay(1) VO = 1Vp-p 25 ns

Settling Time to 1%, Step Input VO = 1Vp-p, RL = 100Ω0.25 µs

Settling Time to 1%, Step Input VO = 6Vp-p, RL = 100Ω0.3 µs

Settling Time to 0.1%, Step Input VO = 1Vp-p, RL = 100Ω0.8 µs

Settling Time to 0.1%, Step Input VO = 6Vp-p, RL = 100Ω1.1 µs

THD, Total Harmonic Distortion(2)

f = 10kHz RL = 100Ω, VO = 6Vp-p –85 dBc

f = 10kHz RL = 15Ω, VO = 6Vp-p –66 –76 dBc

f = 100kHz RL = 100Ω, VO = 6Vp-p –72 dBc

f = 100kHz RL = 15Ω, VO = 6Vp-p –65 dBc

Input Voltage Noise f = 100kHz 30 nV/√Hz

Input Current Noise f = 100kHz 0.5 fA/√Hz

INPUT CHARACTERISTICS

Differential Input Resistance 1011 Ω

Differential Input Capacitance 1pF

Common-Mode Input Resistance 1011 Ω

Common-Mode Input Capacitance 6pF

Input Offset Voltage 5mV

Input Bias Current 1pA

Common-Mode Rejection Ratio Input Referred 62 dB

Power Supply Rejection Ratio Input Referred 60 76 dB

Input Common-Mode Voltage Range(3) 0.5 VDD –0.5 V

OUTPUT CHARACTERISTICS

Differential Output Offset, RTO 10 25 mV

Differential Output Offset Drift, RTO –40°C to +85°C30µV/°C

Differential Output Resistance 0.16 Ω

Peak Current (Continuous) RL = 15Ω200 230 mA

Differential Output Voltage Swing RL = 1kΩ9.6 Vp-p

RL = 100Ω8.5 9.5 Vp-p

RL = 15Ω6.0 6.6 Vp-p

Output Voltage Swing, Each Side RL = 1kΩ0.125 4.875 V

Gain Fixed Gain, Differential 3 V/V

Gain Error ±0.25 dB

POWER SUPPLY

Operating Voltage Range +4.5 +5.0 +5.5 V

Quiescent Current VDD = 5.0V +11 +16 mA

TEMPERATURE RANGE –40 +85 °C

Thermal Resistance,

DRV1100P 8-Pin DIP 100 °C/W

DRV1100U 8-Pin SO-8 125 °C/W

NOTES: (1) Time from 50% point of input step to 50% point of output step. (2) Measurement Bandwidth = 500kHz. (3) Output common-mode voltage follows input

common-mode voltage; therefore, if input VCM = VDD/2, then output VCM = VDD/2.

SPECIFICATIONS

At VDD = +5.0V, VCM = VDD/2, TA = 25°C, unless otherwise specified.

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN

assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject

to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not

authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.

DRV1100

PIN CONFIGURATIONS

Top View Analog Inputs: Current .............................................. ±100mA, Momentary

±10mA, Continuous

Voltage....................................... GND –0.3V to VDD +0.2V

Analog Outputs Short Circuit to Ground (+25°C) ..................... Momentary

Analog Outputs Short Circuit to VDD (+25°C) ........................... Momentary

VDD to GND ..............................................................................–0.3V to 6V

Junction Temperature ................................................................... +150°C

Storage Temperature Range .......................................... –40°C to +125°C

Lead Temperature (soldering, 3s)................................................. +260°C

Power Dissipation .............................. (See Thermal/Analysis Discussion)

ABSOLUTE MAXIMUM RATINGS

In+ 2

In–

Out+

+5V

GND

Out–

PACKAGE/ORDERING INFORMATION

PACKAGE DRAWING

PRODUCT PACKAGE NUMBER(1)

DRV1100P 8-Pin PDIP 006

DRV1100U 8-Lead SO-8 182

NOTE: (1) For detailed drawing and dimension table, please see end of data

sheet, or Appendix C of Burr-Brown IC Data Book.

ELECTROSTATIC

DISCHARGE SENSITIVITY

This integrated circuit can be damaged by ESD. Burr-Brown

recommends that all integrated circuits be handled with

appropriate precautions. Failure to observe proper handling

and installation procedures can cause damage.

ESD damage can range from subtle performance degradation

to complete device failure. Precision integrated circuits may

be more susceptible to damage because very small parametric

changes could cause the device not to meet its published

specifications.

GND

In+

In–

GND

Out–

(+5V)

Out+

DRV1100

TYPICAL PERFORMANCE CURVES

At VDD = +5.0V, VCM = VDD/2, TA = 25°C, unless otherwise specified.

–40

–45

–50

–55

–60

–65

–70

–75

–80

100K

SMALL SIGNAL 2ND HARMONIC DISTORTION

2nd Harmonic (dB)

Frequency (Hz)

1M 10M

= 15Ω

= 1Vp-p

= 100Ω

–40

–45

–50

–55

–60

–65

–70

–75

–80

100K

SMALL SIGNAL 3RD HARMONIC DISTORTION

3rd Harmonic (dB)

Frequency (Hz)

1M 10M

= 1Vp-p

= 100Ω

= 15Ω

–40

–45

–50

–55

–60

–65

–70

–75

–80

100K

LARGE SIGNAL 2ND HARMONIC DISTORTION

2nd Harmonic (dB)

Frequency (Hz)

1M 10M

= 15Ω

= 6Vp-p

= 100Ω

–40

–45

–50

–55

–60

–65

–70

–75

–80

100K

LARGE SIGNAL 3RD HARMONIC DISTORTION

3rd Harmonic (dB)

Frequency (Hz)

1M 10M

= 6Vp-p

= 100Ω

= 15Ω

9.5

8.5

7.5

6.5

5.5

4.5

3.5

2.5

1.5

10K 100K

SMALL SIGNAL FREQUENCY RESPONSE

Differential Gain (dB)

Frequency (Hz)

1M 10M

= 1kΩ

= 100Ω

= 15Ω

= 1Vp-p

9.5

8.5

7.5

6.5

5.5

4.5

3.5

2.5

1.5

10K 100K

LARGE SIGNAL FREQUENCY RESPONSE

Differential Gain (dB)

Frequency (Hz)

1M 10M

= 1kΩ

= 100Ω

= 15Ω

= 6Vp-p

DRV1100

TYPICAL PERFORMANCE CURVES (CONT)

At VDD = +5.0V, VCM = VDD/2, TA = 25°C, unless otherwise specified.

–40

–50

–60

–70

–80

–90 1234

10kHz THD

THD (dBc)

Differential Output Voltage (Vp-p)

5678910

= 15Ω

= 100Ω

= 1kΩ

–40

–50

–60

–70

–80

–90 1234

100kHz THD

THD (dBc)

Differential Output Voltage (Vp-p)

5678910

= 15Ω

= 100Ω

= 1kΩ

+0.5V

–0.5V

SMALL SIGNAL STEP RESPONSE

Differential Voltage (125mV/div)

Time (50ns/div)

Output

Input

= 100Ω

+3V

–3V

LARGE SIGNAL STEP RESPONSE

Differential Voltage (750mV/div)

Time (50ns/div)

Output

Input

= 100Ω

MAXIMUM V

vs SUPPLY VOLTAGE

Differential Output Voltage (Vp-p)

Supply Voltage (V

)

4.5 4.75 5 5.25 5.5

= 100Ω

= 1kΩ

= 15Ω

010K1K 100K

LARGE SIGNAL OPERATING RANGE

Differential Output Swing (Vp-p)

Frequency (Hz)

1M 10M

= 15Ω

= 1kΩ

= 100Ω1% THD

DRV1100

TYPICAL PERFORMANCE CURVES (CONT)

At VDD = +5.0V, VCM = VDD/2, TA = 25°C, unless otherwise specified.

1000

100

DIFFERENTIAL INPUT VOLTAGE NOISE

Voltage Noise (nV/√Hz)

Frequency (Hz)

100 1K 10K 100K 1M

0.1

DIFFERENTIAL OUTPUT IMPEDANCE

Impedance (Ω)

Frequency

1k 10K 100K 1M 10M

3–40 –20 0 20 40 60 80 100

QUIESCENT CURRENT vs TEMPERATURE

Quiescent Current (mA)

Temperature (°C)

= +5V

010K1K 100K

POWER SUPPLY REJECTION vs FREQUENCY

PSRR (dB)

Frequency (Hz)

1M 10M

DRV1100

APPLICATIONS INFORMATION

INTERNAL BLOCK DIAGRAM

The DRV1100 is a true differential input to differential

output fixed gain amplifier. Operating on a single +5V

power supply, it provides an internally fixed differential

gain of +3 and a common-mode gain of +1 from the input to

output. Fabricated on an advanced CMOS process, it offers

very high input impedance along with a low impedance

230mA output drive. Figure 1 shows a simplified internal

block diagram.

In+

In–

Out+

Out–

Buffer

Preamp

FIGURE 1. Simplified DRV1100 Internal Block Diagram.

To achieve the maximum dynamic range, operate the

DRV1100 with the inputs centered at VDD/2. This will place

the output differential swing centered at VDD/2 for maxi-

mum swing and lowest distortion. Purely differential input

signals will produce a purely differential output signal. A

single ended input signal, applied to one input of the

DRV1100, with the other input at a fixed voltage, will

produce both a differential and common-mode output signal.

This is an acceptable mode of operation when the DRV1100

is driving an element with good common-mode rejection

(such as a transformer).

DIFFERENTIAL OUTPUT VOLTAGE AND POWER

Applying the balanced differential output voltage of the

DRV1100 to a load between the outputs will produce a peak-

to-peak voltage swing that is twice the swing of each

individual output. This is illustrated in Figure 2 where the

common-mode voltage is VDD /2. For a load connected

between the outputs, the only voltage that matters is the

differential voltage between the two outputs—the common-

mode voltage does not produce any load current in this case.

The peak power that the DRV1100 can deliver into a

differential load is VP2/RL. The Typical Performance Curves

show the maximum Vp-p versus load and frequency. The

peak voltage (Vp) equals 1/2 of the peak-to-peak voltage

(Vp-p). Squaring 1/2 of the Vp-p and dividing by the load

will give the peak power. For example, the Typical Perfor-

mance Curves show that on +5V supply the DRV1100 will

deliver 6.8Vp-p into 15Ω at 500kHz. The peak load power

under this condition is (6.8Vp-p/2)2/15Ω = 770mW.

SUPPLY VOLTAGE

The DRV1100 is designed for operation on a single +5V

supply. For loads > 200Ω, each output will swing rail to rail.

This gives a peak-to-peak differential output swing that is

approximately = 2 • VDD. For best distortion performance,

the power supply should be decoupled to a good ground

plane immediately adjacent to the package with a 0.1µF

capacitor. In addition, a larger electolytic supply decoupling

capacitor (6.8µF) should be near the package but can be

shared among multiple devices.

DIGITAL SUBSCRIBER LINE APPLICATIONS

The DRV1100 is particularly suited to the high power, low

distortion, requirements of a twisted pair driver in digital

communications applications. These include HDSL (High

bit rate Digital Subscriber Lines), ADSL (Asymmetrical

Digital Subscriber Lines), and RADSL (Rate adaptive ADSL).

Figure 3 shows a typical transformer coupled xDSL line

driver configuration. In general, the DRV1100 is usable for

output power requirements up to 17dBm with a crest factor

up to 6 (crest factor is the ratio of peak to rms voltage).

To calculate the required amplifier power for an xDSL

application—

• Determine the average power required onto the line in the

particular application. The DRV1100 must be able to

deliver twice this power (+3dB) to account for the power

FIGURE 2. DRV1100 Single Ended and Differential Output

Waveforms.

Out+

Out–

Load

DRV1100

loss through the series impedance matching resistors shown

in Figure 3. Twice the required line power must be

delivered by the DRV1100 through the frequency band

of interest with the distortion required by the system.

• Calculate the RMS voltage required at the output of the

DRV1100 with this 2X line power requirement. Vrms =

(2 • PLINE • RL)1/2, where RL is the total load impedance

that the DRV1100 must drive. Multiply this Vrms by 2 •

crest factor to get the total required differential peak-to-

peak voltage at the output. The DRV1100 must be able

to drive the peak-to-peak differential voltage into the

load impedance.

Where possible, the transformer turns ratio may be adjusted

to keep within the DRV1100 output voltage and current

constraints for a given RLINE and desired power onto the

line.

Using the example of Figure 3, assume the average power

desired on a 135Ω line is 14dBm (HDSL). Twice this power

(17dBm) is required into the matching resistors on the

primary side of the transformer. This 135Ω load is reflected

through the 1:4 transformer as a (135/(42)) = 8.4Ω load. The

two series 4.1Ω resistors, along with the 0.2Ω differential

output impedance of the DRV1100, will provide impedance

matching into this 8.4Ω load. The DRV1100 will see ap-

proximately a 16.5Ω load under these conditions. The re-

quired 17dBm (50mW) into this load will need an output

Vrms = (50mW • 16.5)1/2 = 0.91Vrms. Assuming a crest

factor of 3, the differential peak-to-peak output voltage = 6

• 0.91 = 5.45Vp-p. The Typical Performance Curves show

that, at 100kHz, the DRV1100 can deliver this voltage swing

with less than –62dB THD.

OUTPUT PROTECTION

Figure 3 also shows overvoltage and short circuit protection

elements that are commonly included in xDSL applications.

Overvoltage suppressors include diodes or MOV’s. The

outputs of the DRV1100 can be momentarily shorted to

In+

In–

Out+

+5V

DRV1100

GND

Out–

4Ω

Protection Circuits

1:4

Transformer

Line Impedance

135Ω

FIGURE 3. Typical Digital Subscriber Line Application.

ground or to the supply without damage. The outputs are not,

however, designed for a continuous short to ground or the

supply.

POWER DISSIPATION AND THERMAL ANALYSIS

The total internal power dissipation of the DRV1100 is the

sum of a quiescent term and the power dissipated internally

to deliver the load power. The Typical Performance Curves

show the quiescent current over temperature. At +5V sup-

ply, the typical no load supply current of 11mA will dissi-

pate 55mW quiescent power. The rms power dissipated in

the output circuit to deliver a Vrms to a load RL is:

Prms = (VDD – Vrms) • (Vrms/RL)

The internal power dissipation will reach a maximum when

Vrms is equal to VDD/2. For a sinusoidal output, this

corresponds to an output Vp-p = 1.41 • VDD.

As an example, compute the power and junction temperature

under a worst case condition with VDD = +5V and Vrms =

2.5V into a 16Ω differential load (peak output current for a

sinusoid would be 222mA). The total internal power dissi-

pation would be:

(5V • 11mA) + (5V – 2.5V) • (2.5V/16Ω) = 446mW

To compute the internal junctions temperature, this power is

multiplied by the junction to ambient thermal impedance (to

get the temperature rise above ambient) then added to the

ambient temperature. Using the specified maximum ambient

temperature of +85°C, the junction temperature for the

DRV1100 in an SO-8 package under these worst case

conditions will be:

TJ = 85°C + 0.446W • 125°C/W = 141°C

DRV1100

00 0.5 1 1.5

INTERNAL TEMPERATURE RISE

OF DRV1100 IN SOIC

Temperature Rise

Load Voltage (rms)

2 2.5 3 3.5

= 15Ω

Limit at 85°C Ambient

= 100Ω

Often, the RB resistors will be set to a relatively high value

(> 10kΩ) to minimize quiescent current in the reference

path. If a lower input impedance is desired, additional

terminating resistors may be added to the input side of the

blocking capacitors (CB).

The circuit of Figure 5 may also be operated with only a

single ended input. In that case, the reference voltage on the

other input should be decoupled to ground with a 0.1µF

capacitor. In this connection, the input will generate unbal-

anced outputs. The differential output voltage will still be

3 times the input peak-to-peak voltage, but since there is

now a common-mode voltage input, there will be a common

mode voltage output. The output common-mode voltage

will be equal to the input signal’s peak-to-peak swing. This

common-mode component will reduce the available differ-

ential output voltage swing. However, if the output load has

good common-mode rejection, such as a transformer, this is

an acceptable way of using the DRV1100 with a single

ended source.

Figure 6 shows a means of translating a ground centered

single ended input to a purely differential signal for applica-

tion to DRV1100 input. This circuit uses a wideband dual op

amp in cross coupled feedback configuration.

The outputs of this circuit may then be fed into the inputs of

Figure 5. The total gain of Figure 6 is 2 • (RF/RG). The

circuit will act to hold all 4 op amp inputs equal to the

+ input of the lower op amp. Since this is at ground, the

midpoint for the input signal (where the two outputs will be

equal) is also at 0V.

FIGURE 5. AC Coupled Differential Input Interface.

DRV1100

FIGURE 4. Junction Temperature Rise From Ambient for

the DRV1100U.

The internal junction temperature should, in all cases, be

limited to < 150°C. For a maximum ambient temperature of

+85°C, this limits the internal temperature rise to less than

65°C. Figure 4 shows the temperature rise from ambient to

junction for loads of 15Ω and 100Ω. This shows that the

internal junction temperature will never exceed the rated

maximum for a 15Ω load.

INPUT INTERFACE CIRCUITS

Best performance with the DRV1100 is achieved with a

differential input centered at VDD/2. Signals that do not

require DC coupling may be connected as shown in Figure

5 through blocking caps to a midpoint reference developed

through resistor dividers from the supply voltage. The value

for the RB resistors determine four performance require-

ments.

• They bias the inputs at the supply midpoint.

• They provide a DC bias current path for the input to the

DRV1100

• They set the AC input impedance for the source signals to

RB/2.

• They set the low frequency cutoff frequency along with

CB.

1/2

OPA2650

500Ω

+ V

1/2

OPA2650

500Ω

– V

FIGURE 6. Single Ended to Differential Conversion.

PACKAGING INFORMATION

Orderable Device Status (1) Package

Type Package

Drawing Pins Package

Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)

DRV1100U NRND SOIC D 8 75 Green (RoHS &

no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR

DRV1100U/2K5 NRND SOIC D 8 2500 Green (RoHS &

no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR

DRV1100U/2K5G4 NRND SOIC D 8 2500 Green (RoHS &

no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR

DRV1100UG4 NRND SOIC D 8 75 Green (RoHS &

no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in

a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check

http://www.ti.com/productcontent for the latest availability information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements

for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered

at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and

package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS

compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame

retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)

(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder

temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is

provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the

accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take

reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on

incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited

information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI

to Customer on an annual basis.

PACKAGE OPTION ADDENDUM

www.ti.com 11-Nov-2008

Addendum-Page 1

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

A0 (mm) B0 (mm) K0 (mm) P1

(mm) W

(mm) Pin1

Quadrant

DRV1100U/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 11-Mar-2008

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

DRV1100U/2K5 SOIC D 8 2500 346.0 346.0 29.0

PACKAGE MATERIALS INFORMATION

www.ti.com 11-Mar-2008

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandClocks and Timers www.ti.com/clocks Digital Control www.ti.com/digitalcontrolInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyRF/IF and ZigBee® Solutions www.ti.com/lprf Video & Imaging www.ti.com/videoWireless www.ti.com/wireless