2N6071A/B Series Preferred Device Sensitive Gate Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled solid-state devices are needed. Triac type thyristors switch from a blocking to a conducting state for either polarity of applied anode voltage with positive or negative gate triggering. * Sensitive Gate Triggering Uniquely Compatible for Direct Coupling to TTL, HTL, CMOS and Operational Amplifier Integrated Circuit Logic Functions * Gate Triggering 4 Mode -- 2N6071A,B, 2N6073A,B, 2N6075A,B * Blocking Voltages to 600 Volts * All Diffused and Glass Passivated Junctions for Greater Parameter Uniformity and Stability * Small, Rugged, Thermopad Construction for Low Thermal Resistance, High Heat Dissipation and Durability * Device Marking: Device Type, e.g., 2N6071A, Date Code http://onsemi.com TRIACS 4 AMPERES RMS 200 thru 600 VOLTS MT2 MT1 G MAXIMUM RATINGS (TJ = 25C unless otherwise noted) Rating Symbol Value Unit *Peak Repetitive Off-State Voltage(1) (TJ = 40 to 110C, Sine Wave, 50 to 60 Hz, Gate Open) 2N6071A,B 2N6073A,B 2N6075A,B VDRM, VRRM *On-State RMS Current (TC = 85C) Full Cycle Sine Wave 50 to 60 Hz IT(RMS) 4.0 Amps ITSM 30 Amps I2t 3.7 A2s PGM 10 Watts PG(AV) 0.5 Watt VGM 5.0 Volts TJ -40 to +110 C Tstg -40 to +150 C -- 8.0 in. lb. * *Peak Non-repetitive Surge Current (One Full cycle, 60 Hz, TJ = +110C) Circuit Fusing Considerations (t = 8.3 ms) *Peak Gate Power (Pulse Width 1.0 s, TC = 85C) *Average Gate Power (t = 8.3 ms, TC = 85C) *Peak Gate Voltage (Pulse Width 1.0 s, TC = 85C) *Operating Junction Temperature Range *Storage Temperature Range Mounting Torque (6-32 Screw)(2) Volts 200 400 600 3 2 1 TO-225AA (formerly TO-126) CASE 077 STYLE 5 PIN ASSIGNMENT 1 Main Terminal 1 2 Main Terminal 2 3 Gate ORDERING INFORMATION *Indicates JEDEC Registered Data. (1) VDRM and VRRM for all types can be applied on a continuous basis. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. (2) Torque rating applies with use of a compression washer. Mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Main terminal 2 and heatsink contact pad are common. Device Package Shipping 2N6071A TO225AA 500/Box 2N6071B TO225AA 500/Box 2N6073A TO225AA 500/Box 2N6073B TO225AA 500/Box 2N6075A TO225AA 500/Box 2N6075B TO225AA 500/Box Preferred devices are recommended choices for future use and best overall value. Semiconductor Components Industries, LLC, 2000 May, 2000 - Rev. 3 1 Publication Order Number: 2N6071/D 2N6071A/B Series THERMAL CHARACTERISTICS Symbol Max Unit *Thermal Resistance, Junction to Case Characteristic RJC 3.5 C/W Thermal Resistance, Junction to Ambient RJA 75 C/W TL 260 C Maximum Lead Temperature for Soldering Purposes 1/8 from Case for 10 Seconds ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted; Electricals apply in both directions) Symbol Characteristic Min Typ Max Unit -- -- -- -- 10 2 A mA -- -- 2 Volts OFF CHARACTERISTICS *Peak Repetitive Blocking Current (VD = Rated VDRM, VRRM; Gate Open) TJ = 25C TJ = 110C IDRM, IRRM ON CHARACTERISTICS *Peak On-State Voltage(1) (ITM = 6 A Peak) VTM *Gate Trigger Voltage (Continuous dc) (Main Terminal Voltage = 12 Vdc, RL = 100 Ohms, TJ = -40C) All Quadrants VGT Gate Non-Trigger Voltage (Main Terminal Voltage = 12 Vdc, RL = 100 Ohms, TJ = 110C) All Quadrants VGD " *Holding Current (Main Terminal Voltage = 12 Vdc, Gate Open, Initiating Current = 1 Adc) " Volts -- 1.4 2.5 Volts 0.2 -- -- IH (TJ = -40C) (TJ = 25C) Turn-On Time (ITM = 14 Adc, IGT = 100 mAdc) tgt mA -- -- -- -- 30 15 -- 1.5 -- s QUADRANT (Maximum Value) IGT @ TJ I mA II mA III mA IV mA 2N6071A 2N6073A 2N6075A +25C 5 5 5 10 -40C 20 20 20 30 2N6071B 2N6073B 2N6075B +25C 3 3 3 5 -40C 15 15 15 20 Type Gate Trigger Current (Continuous dc) (Main Terminal Voltage = 12 Vdc Vdc, RL = 100 ohms) DYNAMIC CHARACTERISTICS Critical Rate of Rise of Commutation Voltage @ VDRM, TJ = 85C, Gate Open, ITM = 5.7 A, Exponential Waveform, Commutating di/dt = 2.0 A/ms *Indicates JEDEC Registered Data. (1) Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%. http://onsemi.com 2 dv/dt(c) -- 5 -- V/s 2N6071A/B Series SAMPLE APPLICATION: TTL-SENSITIVE GATE 4 AMPERE TRIAC TRIGGERS IN MODES II AND III 14 0V MC7400 4 7 VEE = 5.0 V + -VEE LOAD 2N6071A 510 115 VAC 60 Hz Trigger devices are recommended for gating on Triacs. They provide: 1. Consistent predictable turn-on points. 2. Simplified circuitry. 3. Fast turn-on time for cooler, more efficient and reliable operation. Voltage Current Characteristic of Triacs (Bidirectional Device) + Current Symbol Parameter VDRM IDRM Peak Repetitive Forward Off State Voltage VRRM IRRM VTM IH VTM on state Peak Forward Blocking Current Peak Repetitive Reverse Off State Voltage Quadrant 1 MainTerminal 2 + IH IRRM at VRRM Peak Reverse Blocking Current Maximum On State Voltage off state IH Holding Current Quadrant 3 VTM MainTerminal 2 - http://onsemi.com 3 + Voltage IDRM at VDRM 2N6071A/B Series Quadrant Definitions for a Triac MT2 POSITIVE (Positive Half Cycle) + (+) MT2 Quadrant II (+) MT2 Quadrant I (+) IGT GATE (-) IGT GATE MT1 MT1 REF REF IGT - + IGT (-) MT2 Quadrant III (-) MT2 Quadrant IV (+) IGT GATE (-) IGT GATE MT1 MT1 REF REF - MT2 NEGATIVE (Negative Half Cycle) All polarities are referenced to MT1. With in-phase signals (using standard AC lines) quadrants I and III are used. SENSITIVE GATE LOGIC REFERENCE IC Logic g Functions Firing Quadrant II III TTL 2N6071A Series 2N6071A Series HTL 2N6071A Series 2N6071A Series CMOS (NAND) I 2N6071B Series CMOS (Buffer) Operational Amplifier Zero Voltage Switch IV 2N6071B Series 2N6071B Series 2N6071B Series 2N6071A Series 2N6071A Series 2N6071A Series 2N6071A Series http://onsemi.com 4 2N6071A/B Series 110 110 = 30 TC , CASE TEMPERATURE ( C) TC , CASE TEMPERATURE ( C) 60 100 = 30 60 90 90 120 180 dc a 80 70 120 90 180 a 80 70 1.0 2.0 3.0 IT(AV), AVERAGE ON-STATE CURRENT (AMP) 4.0 = CONDUCTION ANGLE 0 Figure 2. RMS Current Derating 8.0 8.0 a a 180 a 6.0 P(AV) , AVERAGE POWER (WATTS) P(AV) , AVERAGE POWER (WATTS) 4.0 1.0 2.0 3.0 IT(RMS), RMS ON-STATE CURRENT (AMP) Figure 1. Average Current Derating dc 120 = CONDUCTION ANGLE 90 60 4.0 = 30 2.0 0 dc a 6.0 = 180 = CONDUCTION ANGLE 120 4.0 30 2.0 60 90 0 0 1.0 2.0 3.0 IT(AV), AVERAGE ON-STATE CURRENT (AMP) 4.0 0 1.0 2.0 3.0 IT(RMS), RMS ON-STATE CURRENT (AMP) Figure 3. Power Dissipation 3.0 OFF-STATE VOLTAGE = 12 Vdc ALL MODES 2.0 1.0 0.7 0.5 0.3 -60 -40 -20 0 20 40 60 80 100 TJ, JUNCTION TEMPERATURE (C) 4.0 Figure 4. Power Dissipation I GT , GATE TRIGGER CURRENT (NORMALIZED) V GT , GATE TRIGGER VOLTAGE (NORMALIZED) dc a = CONDUCTION ANGLE 0 90 100 120 140 3.0 OFF-STATE VOLTAGE = 12 Vdc ALL MODES 2.0 1.0 0.7 0.5 0.3 -60 Figure 5. Typical Gate-Trigger Voltage -40 -20 0 20 40 60 80 100 TJ, JUNCTION TEMPERATURE (C) 120 Figure 6. Typical Gate-Trigger Current http://onsemi.com 5 140 2N6071A/B Series 40 IH, HOLDING CURRENT (NORMALIZED) 3.0 30 20 10 ITM , ON-STATE CURRENT (AMP) 7.0 5.0 2.0 1.0 0.7 0.5 0.3 -60 TJ = 110C 3.0 GATE OPEN APPLIES TO EITHER DIRECTION -40 -20 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (C) 2.0 Figure 8. Typical Holding Current TJ = 25C 1.0 34 32 PEAK SINE WAVE CURRENT (AMP) 0.7 0.5 0.3 0.2 30 28 26 24 TJ = -40 to +110C f = 60 Hz 22 20 18 16 0.1 0 1.0 2.0 3.0 4.0 14 1.0 5.0 2.0 4.0 5.0 7.0 10 NUMBER OF FULL CYCLES VTM, ON-STATE VOLTAGE (VOLTS) Figure 7. Maximum On-State Characteristics Z JC(t), TRANSIENT THERMAL IMPEDANCE (C/W) 3.0 Figure 9. Maximum Allowable Surge Current 10 5.0 MAXIMUM 3.0 2.0 TYPICAL 1.0 0.5 0.3 0.2 0.1 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 100 200 t, TIME (ms) Figure 10. Thermal Response http://onsemi.com 6 500 1.0 k 2.0 k 5.0 k 10 k 2N6071A/B Series PACKAGE DIMENSIONS TO-225AA (formerly TO-126) CASE 077-09 ISSUE W -B- U F Q -A- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. C M 1 2 3 H K J V G S R 0.25 (0.010) A M M B M D 2 PL 0.25 (0.010) M A M B M DIM A B C D F G H J K M Q R S U V INCHES MIN MAX 0.425 0.435 0.295 0.305 0.095 0.105 0.020 0.026 0.115 0.130 0.094 BSC 0.050 0.095 0.015 0.025 0.575 0.655 5 _ TYP 0.148 0.158 0.045 0.065 0.025 0.035 0.145 0.155 0.040 --- STYLE 5: PIN 1. MT 1 2. MT 2 3. GATE http://onsemi.com 7 MILLIMETERS MIN MAX 10.80 11.04 7.50 7.74 2.42 2.66 0.51 0.66 2.93 3.30 2.39 BSC 1.27 2.41 0.39 0.63 14.61 16.63 5 _ TYP 3.76 4.01 1.15 1.65 0.64 0.88 3.69 3.93 1.02 --- 2N6071A/B Series ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 1:00pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 1:00pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 12:00pm to 5:00pm UK Time) Email: ONlit@hibbertco.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, England, Ireland CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2745 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 8 2N6071/D