A-72 APEM www.apem.com
A
12000X778 series
High performance toggle switches - threaded bushing Ø 11,9 (15/32)
Distinctive features
Approvals
CECC 96201-005
CECC 96201-008
MIL Standards MIL STD 3950 and MIL STD 83731
This range of professional toggle switches is suitable for use in military and
other high specification environments.
Contacts
Highly reliable contacts suitable for low level applications or power applications
Pinned lever
The base of the switch lever is pinned to the bushing, thus earthing the lever to
the bushing. This also provides strain relief to protect the switch if accidentally
knocked.
Double shell case
For high mechanical strength and high electrical insulation.
Compact size
The small rear end of the switch allows space saving behind the panel.
Finish
Black finish on body, bushing, lever and hardware.
Sealing
Panel sealed to IP 67, these switches are frontal sealed by two O-rings and
have full rear end sealing.
Accessories
A comprehensive range of protection boots (both full and half length), locking
levers and security caps are available.
10-Serie 12000X778-A_11-Serie 12000X778-A 08/01/13 14:58 Page72
APEM www.apem.com A-73
A
12000X778 series
High performance toggle switches - threaded bushing Ø 11,9 (15/32)
Specifications
MATERIALS
• Case : diallylphthalate (DAP)
with plastic external shell
(epoxy sealed)
• Actuator : brass, black chrome
plated
• Bushing : brass, black chrome
plated
• Contacts : solid rivet -
gold plated silver/nickel alloy
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load : 4A 28VDC
• Minimum load : 10mA 50mV, 10µA 5VDC
When used above 300mA 28VDC, the gold plating is removed on contact areas and is considered only as a protection
against oxidation during storage.
• Initial contact resistance : 10 m max.
• Insulation resistance : 1.000 M min. at 500VDC
• Dielectric strength :
1.000 Vrms 50 Hz min. between terminals
2.000 Vrms 50 Hz min. between poles
2.000 Vrms 50 Hz min. between terminals and frame
• Contact bounce : 2 ms max.
• Electrical life :
- At 4A 28VDC :
20.000 cycles (10.000 for functions 5, 4-1R, 4-2R)
- At low level (50mV 10mA) :
150.000 cycles (switches with 2 maintained positions)
100.000 cycles (switches with 3 maintained positions)
50.000 cycles (momentary functions 7, 8, 4-1R, 4-2R, 5)
GENERAL SPECIFICATIONS
• Torque : 1,50 Nm (1.10 Ft.lb) max. applied to nut
• Panel thickness : 8 mm (.314) max. - 3 mm (.118) min.
• Shock test : 50g - 11ms (IEC 68-2-27)
• Vibrations : 10-500 Hz - 10g (IEC68-2-6)
• Operating temperature : -40°C to +85°C
• Humidity test : 56 days, 93 % R.H., 40°C (IEC 68-2-3)
• Salt spray test : 96 hours (IEC 68-2-11)
APPROVALS
Many models within this range have full CECC approval and are marked
CECC. Please consult factory for list of approved models.
SEALING
• Front panel sealing by two O-rings
Flatted bush for precise orientation
• Panel seal withstands 1 bar pressure and
remains sealed even when the switch is operated.
• Epoxy sealed terminals
• Splash-proof case
Flat
O-rings
Amps
4 A
2 A
10µA
5 VDC
28 VDC
125 VAC
250 VAC
Volts
50 mV
10mA
48 VDC
1 A
1
10-Serie 12000X778-A_11-Serie 12000X778-A 08/01/13 14:58 Page73
A-74 APEM www.apem.com
A
12000X778 series
High performance toggle switches - threaded bushing Ø 11,9 (15/32)
Overview
12
SERIES
Terminals and bushings
1Solder lug terminals,
threaded bushing
Ø 11,9 (15/32)
2Straight PC terminals,
threaded bushing
Ø 11,9 (15/32)
Number of poles
4Double pole
5Three pole
6Four pole
Electrical functions
6ON - ON
9ON OFF ON
7MOM OFF MOM
8ON OFF MOM
4ON ON ON
ON ON MOM
MOM ON MOM
5ON MOM
Function 4
. For 2 and 4 poles only.
. Must not have blank in
"momentary" box.
Momentary
1R ON ON MOM
2R MOM ON MOM
. For function 4 only.
. Leave blank for other
functions.
ABOUT THIS SERIES
On the following pages, you will find successively :
- model structure of switches
- options in the same order as in above chart
Dimensions : first dimensions are in mm while inches are shown as bracketed numbers.
Fluorescent tip
Blank None
038 White fluorescent
tip to lever
X778
High performance
fully sealed
black switches.
Levers
Blank Standard lever
-12 Short lever
Locking levers
-1V 1 locked position
-2V 2 locked positions
-3V 3 locked positions
Other : see following pages.
Approval
CECC
Availability :
Consult factory for
details of approved
models.
Sealing boots can be used to further protect the switches against dust and water. They are presented in section H.
Mounting accessories : standard hardware supplied with all models : 1 hex nut 14 mm (.551) across flats, part number U41.
This nut is presented after model structure of switches.
Security caps are available to prevent inadvertent lever operation. They are presented in section I.
Packaging unit : 2 pole models : 25 pieces
3 and 4 pole models : 20 pieces .
10-Serie 12000X778-A_11-Serie 12000X778-A 08/01/13 14:58 Page74
APEM www.apem.com A-75
A
12000X778 series
High performance toggle switches - threaded bushing Ø 11,9 (15/32)
Fully sealed - black
Solder lug terminals - four pole
Solder lug terminals - three pole
Solder lug terminals - double pole
MODEL
STRUCTURE
Function 6 Other functions
I II III
12146 X778 ON - ON
12149 X778 ON OFF ON
12147 X778 MOM OFF MOM
12148 X778 ON OFF MOM
12144 X778 ON ON ON
12144-1R X778 MOM ON ON
12144-2R X778 MOM ON MOM
12145 X778 ON MOM
I II III
12156 X778 ON - ON
12159 X778 ON OFF ON
12157 X778 MOM OFF MOM
12158 X778 ON OFF MOM
I II III
12166 X778 ON - ON
12169 X778 ON OFF ON
12167 X778 MOM OFF MOM
12168 X778 ON OFF MOM
12164 X778 ON ON ON
12164-1R X778 ON ON MOM
12164-2R X778 MOM ON MOM
Shown with standard lever
Flat
Flat
Flat
Flat
43 2 312- 1
(.098)
(.047)
(.066)
1.70
1.20
2.50
(.161)
4.10
(.039)
1.00
(.338)
8.60
(.681) (.409)
(.594) (.161)
(.019)
(.629)
(.629)
(.236)
(.098)
A
(15/32-32UNS)
EPOXY
(.157)
I
II
III
15.10 4.10
17.30 10.40
16.00
Ø11.90-32UNS
4.00
0.50
16.00
2.50
6.00
Ø6.00
(.236 DIA)
(.059)
1.50
0.50
10.4017.30
4.1015.10
III
II
I
A
(.019)
(.161)(.594)
(.409)(.681)
6.00
2.50
(.098)
(.236) 16.00
(.629)
(.157)
4.00
EPOXY
Ø6.00
(.236 DIA)
Ø11.90-32UNS
(15/32-32UNS)
(.866)
22.00
1.50
(.059)
0.50
10.4017.30
4.1015.10
III
II
I
A
(.019)
(.161)(.594)
(.409)(.681)
4.00
(.157)
(.236)
(.098)
2.50
6.00
(.236 DIA)
Ø6.00
(15/32-32UNS)
Ø11.90-32UNS
(.629)
16.00
(1.106)
28.10
(.059)
1.50
EPOXY
Function 6
Typical angle of throw (A)
26°
Functions 9, 7, 8, 4 20°
Function 5 12°
10-Serie 12000X778-A_11-Serie 12000X778-A 08/01/13 14:58 Page75
A-76 APEM www.apem.com
A
12000X778 series
High performance toggle switches - threaded bushing Ø 11,9 (15/32)
Fully sealed - black
Straight PC terminals - four pole
Straight PC terminals - three pole
Straight PC terminals - double pole
I II III
12246 X778 ON - ON
I II III
12256 X778 ON - ON
I II III
12266 X778 ON - ON
PANEL CUT-OUT STANDARD HARDWARE
Hex nut
U41 (matt black)
Positions and connections, see next page.
Flat
Flat
Flat
(.681) (.409)
(.594)
(.629)
(.629)
(15/32-32UNS)
EPOXY
(.157)
I
II
III
15.10
17.30 10.40 16.00
Ø11.90-32UNS
4.00
16.00
Ø6.00
(.236 DIA)
(.338)
(.039)
(.236)
(.236)
(.157)
(.062 DIA)
A
1.00
6.00
6.00
Ø1.60
4.00
8.60
(.059)
1.50
(.059)
1.50
22.00
(.866)
(15/32-32UNS)
Ø11.90-32UNS
(.236 DIA)
Ø6.00
EPOXY
4.00
(.157)
(.629)
16.00
(.681) (.409)
(.594)
I
II
III
15.10
17.30 10.40
4.00
6.00
(.157)
(.236)
6.00
1.00
(.236)
(.039)
8.60
(.338)
Ø1.60
(.062 DIA)
A
EPOXY
1.50
(.059)
28.10
(1.106)
16.00
(.629)
Ø11.90-32UNS
(15/32-32UNS)
Ø6.00
(.236 DIA)
(.157)
4.00
(.681) (.409)
(.594)
A
I
II
III
15.10
17.30 10.40
(.236)
(.157)
6.00
4.00
(.236)
6.00
(.338)
8.60
1.00
(.039)
(.062 DIA)
Ø1.60
5.10
(.200)
Ø12.00
(.472 DIA)
(.551) (.090)
Ø11.9-32UNS
(15/32-32UNS)
14.00 2.30
C11COSpicotAC
(.039)
1.00
3.50
(.137)
(.196)
5.00
3,5 mm (.138) short terminals available
for function 6, as well as for functions 9, 7,
8, 4 and 5. On request.
10-Serie 12000X778-A_11-Serie 12000X778-A 08/01/13 14:58 Page76
APEM www.apem.com A-77
A
12000X778 series
High performance toggle switches - threaded bushing Ø 11,9 (15/32)
Positions and connections
FUNCTION
12146
12147
12148
12149
12148CT
12145
12144
12144-1R
12144-2R
12156
12166
12164
TERMINAL
IDENTIFICATION
WIRING FOR 3-WAY SWITCHES
(FUNCTION 4)
LEVER POSITION AND CONNECTIONS
I II III (Flat)
ON - ON
(1-3)-4 (1-3)-2
(5-7)-8 (5-7)-6
MOM OFF MOM
ON OFF MOM
ON OFF ON
MOM OFF ON
1-2 1-3
4-5 4-6
- ON MOM
1-2 1-3
4-5 4-6
ON ON ON
MOM ON ON
MOM ON MOM
1-2 1-3 1-3
4-5 4-5 4-6
ON - ON
(1-3)-4 (1-3)-2
(5-7)-8 (5-7)-6
(9-11)-12 (9-11)-10
ON - ON
1A - 3A 1A - 2A
1C - 3C 1C - 2C
1E - 3E 1E - 2E
1G - 3G 1G - 2G
ON ON ON
1A - 2A 1A - 2A 1A - 3A
1C - 2C 1C - 3C 1C - 3C
1E - 2E 1E - 2E 1E - 3E
1G - 2G 1G - 3G 1G - 3G
External jumper (added by customer)
12164
12144
12144-1R
12144-2R
Flat
A
2
1
33
1
2
4
3-1
2 10
9-11
12
3
1
25
4
6
6
7-5
8 4
3-1
2
C EG
A
2
1
33
1
2
4
3-1
2 10
9-11
12
3
1
25
4
6
6
7-5
8 4
3-1
2

A
2
1
33
1
2
4
3-1
2 10
9-11
12
3
1
2 5
4
6
6
7-5
84
3-1
2
C EGA
2
1
33
1
2
4
3-1
2 10
9-11
12
3
1
2 5
4
6
6
7-5
84
3-1
2

A
2
1
33
1
2
4
3-1
2 10
9-11
12
3
1
2 5
4
6
6
7-5
84
3-1
2
C EG
A
2
1
33
1
2
4
3-1
2 10
9-11
12
3
1
2 5
4
6
6
7-5
84
3-1
2

A
2
1
33
1
2
4
3-1
2 10
9-11
12
3
1
25
4
6
6
7-5
84
3-1
2
C EGA
2
1
33
1
2
4
3-1
2 10
9-11
12
3
1
25
4
6
6
7-5
84
3-1
2

1
4
3
2
6
5
4
1
3
2
6
5
4
1
3
2
6
5
1A
2A
1C
1E
1G
3A
2C
3C
2E
3E
2G
3G
10-Serie 12000X778-A_11-Serie 12000X778-A 08/01/13 14:58 Page77
A-78 APEM www.apem.com
A
-12
(.464)
(.196 DIA)
Ø5.00
11.80
(.468)
11.90
12000X778 series
High performance toggle switches - threaded bushing Ø 11,9 (15/32)
FLUORESCENT TIP
X778
X778
Blank None
038 White fluorescent tip.
Becomes luminous when submitted to ultra-violet rays.
Standard lever Locking lever
LEVERS / LOCKING LEVERS
Locking levers
Standard lever (leave blank) Short lever
Dash compulsory before lever code.
Sealing boots : see section H.
Security caps : see section I.
-1V
1 locked position (function 6)
Typical angle of throw : 26°
-2V
2 locked positions (function 6)
Typical angle of throw : 26°
-3V
3 locked positions (functions 9 and 4)
Typical angle of throw : 20°
Flat
AGENCY APPROVAL
CECC CECC 96201-005 and CECC 96201-008
Availability : consult factory for details of approved models.
Marking : to order switches marked CECC, please complete above box with "CECC". Blank : no agency approval required.
X778
(.468) (.763)
11.90 19.40
(.275 DIA)
Ø7.00
Ø7.00
(.275 DIA)
11.90
(.468)
19.40
(.763)
(.468)
11.90
(.811)
20.60
(.275)
Ø7.00
11.90
(.468) (.681)
(.236 DIA)
17.30
Ø6.00
Functions 9 & 4
Functions 7 & 442R Functions 8 & 441R Functions 8, 9, 44 &
441R Functions 8 & 441R Functions 8, 9, 44 &
441R
Functions 8 & 441R
Functions 8 & 441R Functions 8 & 441R Functions 4 & 9 Functions 7 & 442R Functions 9 & 44
Note : -5V and
-12V are not true
locking levers : no
pulling is required
before actuation.
C12LVX
Le 23-03-2010
ECH:1
-17V -20V
-11V-9V
-12V -13V -15V -16V
-8V-7V-5V-4V
-17V -20V
-12V -13V -15V -16V
10-Serie 12000X778-A_11-Serie 12000X778-A 08/01/13 14:58 Page78