Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Typical Applications Features The HMC611LP4(E) is ideal for IF and RF applications in: Wide Dynamic Range: Up to 63 dB * Cellular/PCS/3G Supply Voltage: +5V * WiMAX, WiBro, WLAN, Fixed Wireless & Radar Excellent Stability over Temperature * Power Monitoring & Control Circuitry Buffered Temperature Sensor Output * Receiver Signal Strength Indication (RSSI) 24 Lead 4x4mm SMT Package: 16mm2 High Accuracy: 1 dB with 54 dB Range Up to 8 GHz * Automatic Gain & Power Control 12 Functional Diagram POWER DETECTORS - SMT General Description The HMC611LP4(E) Logarithmic Detector/Controller converts RF signals at its input, to a proportional DC voltage at its output. The HMC611LP4(E) employs a successive compression topology which delivers extremely high dynamic range and conversion accuracy over a wide input frequency range. As the input power is increased, successive amplifiers move into saturation one by one creating an accurate approximation of the logarithm function. The output of a series of square law detectors is summed, converted into voltage domain and buffered to drive the LOGOUT output. For detection mode, the LOGOUT pin is shorted to the VSET input, and will provide a nominal logarithmic slope of -25mV/ dB and an intercept of 18 dBm (22 dBm for 5.8 GHz). The HMC611LP4(E) can also be used in the controller mode where an external voltage is applied to the VSET pin, to create an AGC or APC feedback loop. Electrical Specifi cations, TA = +25C[1] Parameter Typ. Typ. Typ. Typ. Typ. Units 1 - 3600 5800 7000 8000 10000 MHz 3 dB Dynamic Range 70 66 62 59 50 dB 3 dB Dynamic Range Center -25 -23 -21 -20 -15 dBm 1 dB Dynamic Range 60 61 58 52 42 dB Output Intercept 18 25 23 22 21 dBm Output Slope -25 -24 -26 -28 -32 mV/dB 7 5 8 20 28 mdB/C Input Frequency Temperature Sensitivity @ -10 dBm Input [2] [1] Detector mode measurements; LOGOUT (Pin 15) is shorted to VSET (Pin 16). [2] Measured from TA = -40C to TA = +85C 12 - 48 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Electrical Specifi cations, (continued) Parameter Conditions Min. Typ. Max. Units LOGOUT Interface Output Voltage Range 0 Vcc -1.0 Output Rise Time [3] / Fall Time [4] V 10 / 10 ns 30 k VSET Interface Input Impedance Input Voltage Range Low Frequency Gain 0.25 to 1.35 V 56 dB 700 kHz VSET to LOGOUT Open Loop Corner Frequency 12 Power Down (EN) Interface 0.8 x Vcc [1] Vcc [1] V 0 0.2 x Vcc [1] V Voltage Range for Powerdown Mode Vcc [1]/2 Threshold Voltage V POWER DETECTORS - SMT Voltage Range for Normal Mode Power Supply (Vcc1, Vcc2, Vcc3) Operating Voltage Range 4.5 5.5 Supply Current in Normal Mode V 106 mA 1 mA Supply Current in Power Down Mode [1] Vcc= Vcc1= Vcc2= Vcc3= +5V [3] -10 dBm Input Pulsed; measured from 10% to 70%; C9 removed from board [4] -10 dBm Input Pulsed; measured from 90% to 10%; C9 removed from board Test Conditions Parameter Vcc1 = Vcc2 = Vcc3 Condition +5V Input Zo 50 TA Fin +25 C 900 MHz Component Values Used at Key Application Frequencies with Vcc = +5V Component C1 C2 Frequency (MHz) 50 100 900 1900 2200 3600 5800 7000 7500 8000 10000 100nF 100nF 100nF 100nF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF LOGOUT Voltage & Error vs. Input Power, Fin = 50 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 100 MHz 4 2.6 ERR +25C ERR +85C ERR -40C 2 0.8 Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C 0.2 -70 -60 -50 -40 -30 -20 -10 0 LOGOUT (V) 0.8 -4 0.2 INPUT POWER (dBm) 0 1.4 -2 10 2 -70 ERROR (dB) 0 1.4 ERR +25C ERR +85C ERR -40C 2 ERROR (dB) LOGOUT (V) 2 4 2.6 -2 Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C -4 -60 -50 -40 -30 -20 -10 0 10 INPUT POWER (dBm) Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 49 HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 900 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 1900 MHz ERR +25C ERR +85C ERR -40C 2 -60 -50 -40 -30 -20 -10 0 ERR +25C ERR +85C ERR -40C 0 0.8 -4 0.2 -4 -70 -60 -50 -40 ERR +25C ERR +85C ERR -40C Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C 0.2 -30 -20 -10 0 ERR +25C ERR +85C ERR -40C -2 0.8 -4 0.2 10 0 -4 -60 -50 ERR +25C ERR +85C ERR -40C -10 0 LOGOUT (V) LOGOUT (V) 0.2 -20 ERR +25C ERR +85C ERR -40C 10 0.8 -4 0.2 10 3 0 1.4 -2 INPUT POWER (dBm) -70 -3 Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C -6 -60 -50 -40 -30 -20 -10 INPUT POWER (dBm) Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C 12 - 50 0 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 0 10 ERROR (dB) Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C -30 -10 6 2 ERROR (dB) 0 -40 -20 2.6 2 1.4 -50 -30 LOGOUT Voltage & Error vs. Input Power, Fin = 7000 MHz 4 -60 -40 INPUT POWER (dBm) 2.6 -70 -2 Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C -70 LOGOUT Voltage & Error vs. Input Power, Fin = 5800 MHz 0.8 2 1.4 INPUT POWER (dBm) 2 10 4 2 LOGOUT (V) 0 -40 0 ERROR (dB) LOGOUT (V) 2 1.4 -50 -10 2.6 ERROR (dB) POWER DETECTORS - SMT 4 -60 -20 LOGOUT Voltage & Error vs. Input Power, Fin = 3600 MHz 2.6 -70 -30 INPUT POWER (dBm) LOGOUT Voltage & Error vs. Input Power, Fin = 2200 MHz 0.8 -2 Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C INPUT POWER (dBm) 2 2 1.4 -2 10 4 ERROR (dB) Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C 0.2 -70 2 0 1.4 0.8 12 2.6 ERROR (dB) LOGOUT (V) 2 4 LOGOUT (V) 2.6 HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 8000 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 10000 MHz 10 ERR +25C ERR +85C ERR -40C 5 Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C 0 -70 -60 -50 -40 -30 -20 -10 0 -5 0.8 -10 0.2 10 0 1.4 -10 -70 -60 -50 INPUT POWER (dBm) -30 -20 -10 0 -20 -22 SLOPE (mV/dB) -10 -20 -30 -40 -24 -26 -28 +25C +85C -40C -30 0 2 4 6 12 10 LOGOUT Slope vs. Frequency 0 RETURN LOSS (dB) -40 INPUT POWER (dBm) Input Return Loss -50 -5 Ideal LOGOUT +25C LOGOUT +85C LOGOUT -40C 8 10 FREQUENCY (GHz) -32 0 2 4 6 FREQUENCY (GHz) 8 10 POWER DETECTORS - SMT 0.6 5 ERROR (dB) 0 1.2 ERR +25C ERR +85C ERR -40C 2 ERROR (dB) LOGOUT (V) 1.8 10 2.6 LOGOUT (V) 2.4 Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 51 HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz 26 27 24 24 21 18 +25C +85C -40C 15 12 LOGOUT Intercept vs. Supply Voltage 30 INTERCEPT (dBm) INTERCEPT (dBm) LOGOUT Intercept vs. Frequency 12 20 18 0.1GHz 1.9GHz 3.6GHz 5.8GHz 8GHz 10GHz 16 14 0 2 4 6 8 10 FREQUENCY (GHz) POWER DETECTORS - SMT 22 12 4.5 5 Vcc1, Vcc2, Vcc3 (V) Absolute Maximum Ratings Vcc1, Vcc2, Vcc3 +5.6V EN +5.6V VSET Input Voltage +5.6V LOGOUT Output Current 3 mA RF Input Power +15 dBm Junction Temperature 125 C Continuous Pdiss (T = 85C) (Derate 7.95 mW/C above 85C) 1.55 Watts Thermal Resistance (Rth) (junction to lead) 42 C/W Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS [1] Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C 12 - 52 5.5 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HMC APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC611LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC611LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 POWER DETECTORS - SMT 12 Package Marking [3] [1] H611 XXXX [2] H611 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 53 HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Pin Descriptions Pin Number Function Description 1, 6, 7, 13, 17, 18, 21, 22 N/C These pins are not connected internally. 2 TEMP Temperature sensor output pin 3, 4 IN+, IN- RF Input pins. Connect RF to IN+, and AC couple IN- to ground for single-ended operation. 5 EN Enable pin, connect to Vcc1, Vcc2, Vcc3 for normal operation. Applying voltage <0.2 x (Vcc1, Vcc2, Vcc3) will initiate power saving mode. 8 - 12, 19, 20, 23, 24 Vcc1, Vcc2, Vcc3 Bias supply. Connect supply voltage to these pins with appropriate filtering. 14 CLPF Loop filter capacitor for output ripple filtering. Interface Schematic POWER DETECTORS - SMT 12 12 - 54 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Pin Descriptions (Continued) Function Description 15 LOGOUT Logarithmic output that converts the input power to a DC level in detector mode. Short this pin to VSET for detector mode. 16 VSET VSET input in controller mode. Short this pin to LOGOUT for detector mode. Package Base GND Exposed paddle must be connected to RF and DC ground. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 POWER DETECTORS - SMT Pin Number 12 - 55 HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Application & Evaluation PCB Schematic POWER DETECTORS - SMT 12 Notes Note 1: The HMC611LP4 & HMC611LP4E evaluation boards are pre-assembled for single-ended input, and detector/RSSI mode. Note 2: For detector mode, connect high impedance volt meter to the LOGOUT port, and make no connection to VSET. LOGOUT is shorted to VSET by R9, as required for detector mode. Note 3: For controller mode, remove R9 and install 0 ohm resistor (R11), then make appropriate connection to LOGOUT and VSET. In controller mode, the LOGOUT output can be used to drive a variable gain amplifier, or a variable attenuator, either directly or through a buffer or microcontroller. VSET should be connected to an external supply, typically between +0.6 and +1.9V. 12 - 56 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC611LP4 / 611LP4E v04.0309 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Evaluation PCB List of Materials for Evaluation PCB 121493 [1] Item Description J1 - J3 PC Mount SMA Connector J4 Molex Connector Header J5 - J9 DC Pin C1, C2, C3, C5, C7 100 pF Capacitor, 0402 Pkg. C4, C6, C8 0.1F Capacitor, 0402 Pkg. C9 220 pF Capacitor, 0402 Pkg. R1 68 Resistor, 0402 Pkg. R2 1k Resistor, 0402 Pkg. R3 10k Resistor, 0402 Pkg. R4 - R6, R9, R12 0 Resistor, 0402 Pkg. R13 180 Resistor, 0402 Pkg. R14 27.4 Resistor, 0402 Pkg. R15 15 Resistor, 0402 Pkg. R16 49.9 Resistor, 0402 Pkg. U1 HMC611LP4 / HMC611LP4E Logarithmic Detector / Controller PCB [2] 121490 Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. POWER DETECTORS - SMT 12 [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 57 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC611LP4TR HMC611LP4ETR