54F374 54F374 Octal D-Type Flip-Flop with TRI-STATE(RM) Outputs Literature Number: SNOS190 54F/74F374 Octal D-Type Flip-Flop with TRI-STATEE Outputs General Description Features The 'F374 is a high-speed, low-power octal D-type flip-flop featuring separate D-type inputs for each flip-flop and TRI-STATE outputs for bus-oriented applications. A buffered Clock (CP) and Output Enable (OE) are common to all flip-flops. Y Commercial Y Y Y Edge-triggered D-type inputs Buffered positive edge-triggered clock TRI-STATE outputs for bus-oriented applications Guaranteed 4000V minimum ESD protection Package Number Military Package Description N20A 20-Lead (0.300x Wide) Molded Dual-In-Line J20A 20-Lead Ceramic Dual-In-Line 74F374SC (Note 1) M20B 20-Lead (0.300x Wide) Molded Small Outline, JEDEC 74F374SJ (Note 1) M20D 20-Lead (0.300x Wide) Molded Small Outline, EIAJ 74F374MSA (Note 1) MSA20 20-Lead Molded Shrink Small Outline, EIAJ Type II 54F374FM (QB) W20A 20-Lead Cerpack 54F374LM (QB) E20A 20-Lead Ceramic Leadless Chip Carrier, Type C 74F374PC 54F374DM (QB) Note 1: Devices also available in 13x reel. Use suffix e SCX, SJX, and MSAX. Logic Symbols Connection Diagrams Pin Assignment for DIP, SOIC, SSOP and Flatpak Pin Assignment for LCC TL/F/9524-1 IEEE/IEC TL/F/9524 - 3 TL/F/9524 - 2 TL/F/9524-4 TRI-STATEE is a registered trademark of National Semiconductor Corporation. C1995 National Semiconductor Corporation TL/F/9524 RRD-B30M75/Printed in U. S. A. 54F/74F374 Octal D-Type Flip-Flop with TRI-STATE Outputs May 1995 Unit Loading/Fan Out 54F/74F Pin Names D0 - D7 CP OE O0 - O 7 Description Input IIH/IIL Output IOH/IOL U.L. HIGH/LOW Data Inputs 1.0/1.0 20 mA/b0.6 mA Clock Pulse Input (Active Rising Edge) 1.0/1.0 20 mA/b0.6 mA TRI-STATE Output Enable Input (Active LOW) 1.0/1.0 20 mA/b0.6 mA TRI-STATE Outputs 150/40 (33.3) b3 mA/24 mA (20 mA) Functional Description Truth Table The 'F374 consists of eight edge-triggered flip-flops with individual D-type inputs and TRI-STATE true outputs. The buffered clock and buffered Output Enable are common to all flip-flops. The eight flip-flops will store the state of their individual D inputs that meet the setup and hold time requirements on the LOW-to-HIGH Clock (CP) transition. With the Output Enable (OE) LOW, the contents of the eight flipflops are available at the outputs. When the OE is HIGH, the outputs go to the high impedance state. Operation of the OE input does not affected the state of the flip-flops. CP OE Internal Register Output Dn Inputs H L X L L X L L H H L X H L Z On H e HIGH Voltage Level L e LOW Voltage Level X e Immaterial Z e High Impedance L e LOW-to-HIGH Clock Transition Logic Diagram TL/F/9524 - 5 Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. 2 Absolute Maximum Ratings (Note 1) ESD Last Passing Voltage (Min) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Storage Temperature b 65 C to a 150 C Ambient Temperature under Bias Junction Temperature under Bias Plastic b 55 C to a 125 C 4000V Note 1: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Note 2: Either voltage limit or current limit is sufficient to protect inputs. Recommended Operating Conditions b 55 C to a 175 C b 55 C to a 150 C VCC Pin Potential to Ground Pin Free Air Ambient Temperature Military Commercial b 0.5V to a 7.0V b 0.5V to a 7.0V Input Voltage (Note 2) b 30 mA to a 5.0 mA Input Current (Note 2) Voltage Applied to Output in HIGH State (with VCC e 0V) b 0.5V to VCC Standard Output b 0.5V to a 5.5V TRI-STATE Output Current Applied to Output in LOW State (Max) twice the rated IOL (mA) b 55 C to a 125 C 0 C to a 70 C Supply Voltage Military Commercial a 4.5V to a 5.5V a 4.5V to a 5.5V DC Electrical Characteristics Symbol 54F/74F Parameter Min VIH Input HIGH Voltage VIL Input LOW Voltage VCD Input Clamp Diode Voltage VOH Output HIGH Voltage Typ Units 2.0 54F 10% VCC 54F 10% VCC 74F 10% VCC 74F 10% VCC 74F 5% VCC 74F 5% VCC VCC Conditions Max V Recognized as a HIGH Signal 0.8 V Recognized as a LOW Signal b 1.2 V 2.5 2.4 2.5 2.4 2.7 2.7 Min IIN e b18 mA V Min IOH IOH IOH IOH IOH IOH IOL e 20 mA IOL e 24 mA e e e e e e b 1 mA b 3 mA b 1 mA b 3 mA b 1 mA b 3 mA VOL Output LOW Voltage 54F 10% VCC 74F 10% VCC 0.5 0.5 V Min IIH Input HIGH Current 54F 74F 20.0 5.0 mA Max VIN e 2.7V IBVI Input HIGH Current Breakdown Test 54F 74F 100 7.0 mA Max VIN e 7.0V ICEX Output HIGH Leakage Current 54F 74F 250 50 mA Max VOUT e VCC VID Input Leakage Test 74F V 0.0 IID e 1.9 mA All Other Pins Grounded IOD Output Leakage Circuit Current 74F 3.75 mA 0.0 VIOD e 150 mV All Other Pins Grounded IIL Input LOW Current b 0.6 mA Max VIN e 0.5V IOZH Output Leakage Current 50 mA Max VOUT e 2.7V IOZL Output Leakage Current b 50 mA Max VOUT e 0.5V IOS Output Short-Circuit Current b 150 mA Max VOUT e 0V IZZ Bus Drainage Test 500 mA 0.0V VOUT e 5.25V ICCZ Power Supply Current 86 mA Max VO e HIGH Z 4.75 b 60 55 3 AC Electrical Characteristics Symbol Parameter 74F 54F 74F TA e a 25 C VCC e a 5.0V CL e 50 pF TA, VCC e Mil CL e 50 pF TA, VCC e Com CL e 50 pF Min Typ fmax Maximum Clock Frequency 100 140 Max Min Max tPLH tPHL Propagation Delay CP to On 4.0 4.0 6.5 6.5 8.5 8.5 4.0 4.0 10.5 11.0 4.0 4.0 10.0 10.0 tPZH tPZL Output Enable Time 2.0 2.0 9.0 5.8 11.5 7.5 2.0 2.0 14.0 10.0 2.0 2.0 12.5 8.5 tPHZ tPLZ Output Disable Time 2.0 1.5 5.3 4.3 7.0 5.5 2.0 1.5 8.0 7.5 2.0 1.5 8.0 6.5 60 Min Units Max 70 MHz ns ns AC Operating Requirements Symbol Parameter 74F 54F 74F TA e a 25 C VCC e a 5.0V TA, VCC e Mil TA, VCC e Com Min Min Min Max Max ts(H) ts(L) Setup Time, HIGH or LOW Dn to CP 2.0 2.0 2.5 2.0 2.0 2.0 th(H) th(L) Hold Time, HIGH or LOW Dn to CP 2.0 2.0 2.0 2.5 2.0 2.0 tw(H) tw(L) CP Pulse Width HIGH or LOW 7.0 6.0 7.0 6.0 7.0 6.0 Units Max ns ns Ordering Information The device number is used to form part of a simplified purchasing code where the package type and temperature range are defined as follows: 74F 374 S Temperature Range Family 74F e Commercial 54F e Military C X Special Variations QB e Military grade device with environmental and burn-in processing X e Devices shipped in 13x reel Device Type Package Code P e Plastic DIP D e Ceramic DIP F e Flatpak L e Leadless Chip Carrier (LCC) S e Small Outline SOIC JEDEC SJ e Small Outline SOIC EIAJ MSA e Shrink Small Outline (EIAJ SSOP) Temperature Range C e Commercial (0 C to a 70 C) M e Military (b55 C to a 125 C) NOTE: Not required for MSA package code 4 Physical Dimensions inches (millimeters) 20-Lead Ceramic Leadless Chip Carrier (L) NS Package Number E20A 20-Lead Ceramic Dual-In-Line Package (D) NS Package Number J20A 5 Physical Dimensions inches (millimeters) (Continued) 20-Lead (0.300x Wide) Molded Small Outline Package, JEDEC (S) NS Package Number M20B 20-Lead (0.300x Wide) Molded Small Outline Package, EIAJ (SJ) NS Package Number M20D 6 Physical Dimensions inches (millimeters) (Continued) 20-Lead (0.300x Wide) Molded Shrink Small Outline Package, EIAJ, Type II (MSA) NS Package Number MSA20 20-Lead (0.300x Wide) Molded Dual-In-Line Package (P) NS Package Number N20A 7 54F/74F374 Octal D-Type Flip-Flop with TRI-STATE Outputs Physical Dimensions inches (millimeters) (Continued) 20-Lead Ceramic Flatpak (F) NS Package Number W20A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 2900 Semiconductor Drive P.O. Box 58090 Santa Clara, CA 95052-8090 Tel: 1(800) 272-9959 TWX: (910) 339-9240 National Semiconductor GmbH Livry-Gargan-Str. 10 D-82256 F4urstenfeldbruck Germany Tel: (81-41) 35-0 Telex: 527649 Fax: (81-41) 35-1 National Semiconductor Japan Ltd. Sumitomo Chemical Engineering Center Bldg. 7F 1-7-1, Nakase, Mihama-Ku Chiba-City, Ciba Prefecture 261 Tel: (043) 299-2300 Fax: (043) 299-2500 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductores Do Brazil Ltda. Rue Deputado Lacorda Franco 120-3A Sao Paulo-SP Brazil 05418-000 Tel: (55-11) 212-5066 Telex: 391-1131931 NSBR BR Fax: (55-11) 212-1181 National Semiconductor (Australia) Pty, Ltd. Building 16 Business Park Drive Monash Business Park Nottinghill, Melbourne Victoria 3168 Australia Tel: (3) 558-9999 Fax: (3) 558-9998 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated