High Voltage
Differential
Probes
HVD3605A, HVD3206A
HVD310xA
The HVD3000A series high voltage differential probes provide high CMRR
over a broad frequency range to simplify the measurement challenges
found in noisy, high common-mode power electronics environments.
The probe’s design is easy-to-use and enables safe, precise high voltage
oating measurements.
Key Features
1 kV, 2 kV, 6 kV CAT safety
rated models
Widest differential voltage
ranges available
Exceptional common-mode
rejection ratio (CMRR) across a
broad frequency range
1% gain accuracy
High offset capability at both
high and low attenuation
AC and DC coupling
ProBus active probe interface
with automatic scaling
AutoZero with auto
disconnect switch
Wide oscilloscope compatibility
Exceptional Common-Mode
Rejection Ratio
The CMRR for the probes is
exceptional out to very high
frequencies, greatly improving
measurement capability in the noisy,
high common-mode environments
found in power electronics. The high
CMRR combined with low probe
noise and high offset capability
provides superior measurement
capabilities compared to other HV
differential probes.
High Precision Measurements
HVD3000A series probes provide 1%
gain accuracy enabling precise voltage
measurements. AutoZero capability
ensures further measurement precision
by allowing small offset drifts to be
calibrated out of the measurement.
This feature can be applied without
removing the HVD3000A leads from
the device under test.
Widest Application Coverage
The HVD3000A series cover the fullest
range of applications, from 120/240V
switch-mode power supplies through
600 V class and 5 kV class electrical
apparatus, Each model has the best
available gain accuracy, widest differ-
ential and offset voltage range, and
superior CMRR.
1500 Vdc CAT III Rating
The HVD3206A supports 1500 Vdc
solar photovoltaic (PV) measurements
per the IEC/EN 61010- 031:2015 stan-
dard. It has a 1500 Vdc CAT III and a
2000 V (DC+peakAC) CAT I rating.
Complete Probe Integration
The ProBus interface provides power
and communication to the probe
eliminating the need for a separate
power supply or batteries. Attenuation
is automatically selected based on
oscilloscope gain range (V/div) setting.
2
WIDE APPLICATION COVERAGE - 600 V TO 5 KV APPARATUS
600 V Class, 3-phase Electrical Apparatus
The HVD310xA probes are available in a range of bandwidths from 25 to 120 MHz with standard 2 meter cable (6 meter
cable model available). All probes have industry best CMRR for best noise-immunity, are guaranteed to 1% gain accuracy,
and have the industry’s widest differential voltage range in a 1 kV rated high voltage differential probe.
Only 1 kV safety rated probe that
serves the full 600 V class requirement
1500 V differential range with
industry’s best overshoot
measurement capability (to 2000 Vpk)
Industry’s best offset capability
(1500 V) when used with HDO Series
oscilloscopes
Bandwidth rating up to 120 MHz
6 meter cable model available
(HVD3106A-6M)
Models available without accessories
for a lower cost (HVD310xA-NOACC)
5 kV Class, 3-phase Electrical Apparatus
The HVD3605A probe is safety-rated for 6000 Vrms and 8485 V(DC + peak AC) for full coverage of 5 kV class apparatus.
The probe has ample 100 MHz of bandwidth, is standard with a 6 meter cable, is guaranteed to 1% gain accuracy, has
excellent CMRR, and has the industry’s widest differential voltage range.
Only probe that permits AC Line,
DC Bus, and Drive/Inverter output
voltage probing through
4160 V apparatus ratings
Industry’s best overshoot
measurement capability
(to 7600 Vpk)
Industry’s best offset capability
(6000 V) when used with
HDO Series oscilloscopes
Standard 6 meter cable
*Based on 50% overshoot condition
*Based on 25% overshoot condition
Sinusoidal AC
Line Input DC Bus
Voltage Drive / Inverter
Pulse-Width Modulated (PWM) Output
Vrms or
Vac
Vpk-pk Vdc
Vpk (Rated) Vpk (with Overshoot)*
Line-Line Line-
Neutral Line-Line Line-
Neutral Line-Line Line-
Neutral
400 1131 653 566 566 327 849 491
480 1358 784 679 679 392 1019 588
600 1697 980 849 849 490 1274 735
690 1952 1127 976 976 563 1464 845
Sinusoidal AC
Line Input DC Bus
Voltage Drive / Inverter
Pulse-Width Modulated (PWM) Output
Vrms or
Vac
Vpk-pk Vdc
Vpk (Rated) Vpk (with Overshoot)*
Line-Line Line-
Neutral Line-Line Line-
Neutral Line-Line Line-
Neutral
2400 6788 3920 3395 3395 1960 4244 2450
3300 9334 5388 4666 4666 2694 5833 3368
4160 11766 6794 5884 5884 3397 7355 4246
3
WORLD’S ONLY 2 KV SAFETY RATED MODEL
Solar PV Inverters
The HVD3206A probe is rated to 1500 Vdc (2000 V DC + peak AC). This makes the probe ideal for testing single-phase
or three-phase inverters or newer 1500 Vdc rated string-inverters (per IEC/EN 61010-031:2015). The HVD3206A has
the same excellent 1% gain accuracy, industry-leading CMRR, industry-best offset range, standard 2 meter cable (6
meter cable model available), and a guaranteed 2000 Vpk differential voltage range.
Only 1500 Vdc safety rated probe per
IEC/EN 61010-031:2015
Guaranteed 2000 Vpk differential
voltage range
Industry’s best offset capability
(1500 V) when used with HDO Series
oscilloscopes
Bandwidth rating up to 120 MHz
6 meter cable model available
(HVD3206A-6M)
DC-DC Converters
High-power DC-DC converters can operate at substantial voltages, 500 Vdc or higher. The HVD310xA models provide up to
1000 Vdc common-mode (HVD3206A models provide up to 1500 Vdc) and high precision (1% gain accuracy) DC voltage
measurements. Automatic switchable attenuation keeps the probe in the optimum measurement range. Multiple probes
can be used to understand complex device switching performance.
Common mode range up to ±2000 V
(DC + peak AC) with HVD3206A
High precision - 1% accuracy
Automatic gain switching for optimum
performance
*Based on 30% overshoot condition
Solar String DC
Bus Voltage Sinusoidal AC Output
Vdc
Vpk (Rated) Vpk (with Overshoot)*
Line-Line Line-
Neutral Line-Line Line-
Neutral
1000 849 490 1104 637
1500 849 490 1104 637
4
SUPERIOR PERFORMANCE AT LOWER VOLTAGES
120 V / 240 V Half-Bridge Circuit Topologies
Single-phase switch-mode power supplies and other devices utilizing half-bridge topologies need test and validation at DC
bus voltages up to 340 Vdc with up to 680 Vp-p on the input voltage. HVD310xA probes are cost-effective solutions for
probing the wide range of high voltage signals present in these systems. “No Accessory (NOACC)” versions of these probes
permit additional cost savings. Use your existing accessories or purchase just the ones you want.
MOSFET/IGBT Devices
Upper-side Gate Drive Voltage Measurements
Typically from 3 to 20 volts and “floating” at up to the DC
Bus voltage. HVD-A Series probes can provide very good
results, but the HVFO High Voltage Fiber Optic probe
is optimized for the best upper-side gate drive voltage
measurements with 140 dB CMRR, reduced DUT loading,
and better pulse response.
Device Analysis
Conduction loss or Rds(on) measurements require a
voltage probing solution that has high CMRR, fast overdrive
recovery, voltage clamping (so the oscilloscope is not
overdriven), compensation flatness, gain/amplication to
see small signal details, and precise offset generation to
see the switching device’s turn-off performance. For this
type of analysis, the Teledyne LeCroy DA1855A Differential
Amplier is the best solution. It provides 100 MHz
bandwidth, excellent common mode rejection ratio (CMRR)
of 100,000:1 (typical), and overdrive recovery to within
100 mV from a 400 V input signal in less than 100 ns.
High precision - 1% accuracy
Automatic gain switching for optimum
performance
Input Voltage
(Vrms or Vac)Input Voltage
(Vpk-pk)DC Bus Voltage
(Vdc)Output PWM Voltage
(Vpk)
120 340 170 170
240 680 340 340
DA1855A
Differential Amplier
HVFO103
High Voltage Fiber
Optically-Isolated Probe
5
UNDERSTANDING HV DIFFERENTIAL PROBE RATINGS
AC line voltages and power electronics systems can operate at very high voltages, and all parts of the measurement
circuit are not necessarily connected to ground, requiring HV safety ratings. Additionally, a variety of terms may be used
to describe the same voltage. Below is a simple tutorial to help you understand the various types of voltage terms and
how they relate to each other. Understanding these voltage terms is necessary to ensure the correct probe selection.
Rectied AC (DC Bus/Link Voltage)
For three-phase inputs, the three Line-Neutral (L-N) AC
Line inputs are rectied and summed to provide a “stiff” DC
(bus/link) voltage for the input to an inverter subsection.
The example shown to the right is for a 600 Vrms system.
The Line-Neutral RMS voltages are 600V/√3, and each
Vpeak(L-N) is calculated as √2*Vrms. The DC bus voltage
after rectication and ltering is equal to √3*Vpeak(L-N), or
847 Vdc in this case.
Single-phase AC Line Input
Ratings are provided in Vrms (also referred to as Vac) referred
Line-Neutral. AC Line inputs are usually grounded and these
voltages can be assumed to have a 0V reference voltage.
Vpeak is calculated as √2*Vrms and Vpk-pk is calculated as
2*Vpeak. The example to the right is for a 120 Vrms rating.
Three-phase AC Line Input
Ratings are provided in Vrms (also referred to as Vac)
referred Line-Line (L-L), which can be converted in
magnitude to a Line-Neutral basis by dividing by √3.
Vpeak (L-L) is calculated √2*Vrms and Vpk-pk is calculated
as 2*Vpeak. The example on the left is for a 480 Vrms
three-phase rated system with signals shown as Line-Line.
Inverter or Drive H-Bridge or
Cascaded H-Bridge Outputs
The nominal peak voltage (+ or -) of the PWM signals
without accounting for signal overshoot is equal to the DC
bus voltage. The measured 0V differential voltage value is
not ground-referenced, and therefore a differential probe
suitably rated to the DC bus voltage is recommended. Note
that the +Vpeak and -Vpeak plus overshoot safety margin
(typically ~50%) is what the HV differential probe must
measure - Vpk-pk (2*Vpeak) will never occur in the circuit.
6
SPECIFICATIONS
HVD3102A HVD3106A HVD3106A-6M
Bandwidth 25 MHz 120 MHz 80 MHz
Rise Time (10-90) 14 ns 2.9 ns 4.4 ns
Differential Voltage
Range (High Attenuation) 1500 V (DC + peak AC) from 7 to 500 V/
div with up to 1500 V offset.
1750 V maximum typical measurable
differential voltage before saturation.
1500 V (DC + peak AC) from 7 to 500 V/div with up to 1500 V offset.
2000 V maximum typical measurable differential voltage before saturation
Differential Voltage
Range (Low Attenuation) 27.6 V (DC + peak AC) from 100 mV/div to 6.9 V/div with up to 150 V offset
Common Mode Voltage
Range ±1500 V (DC + peak AC), 1000 Vrms
Maximum Input Voltage
to Earth ±1500 Vpk (nominal, either input to ground)
Max Safe Input Voltage 1000 Vrms CAT III
Sensitivity 100 mV/div to
6.9V/div (100X)
7V/div to 500V/div (1000X)
100 mV/div to
6.9V/div (50X)
7V/div to 500V/div (500X)
100 mV/div to 6.9V/div (50X)
7V/div to 500V/div (500X)
Gain Accuracy 1% (LF, guaranteed)
Slew Rate 100 V/ns (maximum) 400 V/ns (maximum) 270 V/ns (maximum)
Attenuation 100x / 1000x 50x / 500x 50x / 500x
Input Impedance 10 MΩ || 2.5 pF (between inputs), 5 MΩ || 5.0 pF (either input to ground)
Input Coupling DC only
Output Coupling AC or DC coupling
Output Termination 1 MΩ
Interface ProBus
Input Lead Length 40 cm input lead length
Cable Length (input lead
to oscilloscope
connection)
2.25 m 6.8 m
Noise and Rejection
CMRR (Typical) DC - 60 Hz: 85 dB
1 MHz: 65 dB
5 MHz: 40 dB
20 MHz: 30 dB
DC - 60 Hz: 85 dB
1 MHz: 65 dB
5 MHz: 40 dB
20 MHz: 30 dB
100 MHz: 30 dB
DC - 60 Hz: 85 dB
1 MHz: 65 dB
5 MHz: 40 dB
20 MHz: 30 dB
80 MHz: 30 dB
Noise (Probe) 100X: <15 mVrms
1000X: <85 mVrms
(referred to input)
50X: <30 mVrms
500X: <150 mVrms
(referred to input)
50X: <30 mVrms
500X: <150 mVrms
(referred to input)
Environmental
Temperature (Operating) 0°C to 50°C
Temperature
(Non-Operating) -40°C to 70°C
Humidity (Operating) 5% to 80% RH (Non-Condensing) up to 30°C, decreasing linearly to 45% RH at 50°C
Humidity (Non-Operating) 5% to 95% RH (Non-Condensing), 75% RH above 30°C, 45% RH above 40°C
Altitude (Operating) 3000 m maximum
When used with clip accessories, 2000 m maximum
Altitude (Non-Operating) 10,000 m
Pollution Degree 2, Indoor use only
Certications
CE (LVD Directive
2006/95/EC) IEC/EN 61010-031:2015
CE (EMC Directive
2004/108/EC) IEC/EN 61326-1:2013
UL Listed UL 61010-031 (Second Edition)
cUL Listed CAN/CSA-C22.2 No. 61010-031-15
7
HVD3206A HVD3206A-6M HVD3605A
Bandwidth 120 MHz 80 MHz 100 MHz
Rise Time (10-90) 2.9 ns 4.4 ns 4.3 ns
Differential Voltage
Range (High Attenuation) 2000 V (DC + peak AC) from 7 to 500
V/div
with up to 1500V offset.
2000 V (DC + peak AC) from 7 to 500
V/div
with up to 1500V offset.
7000 V (DC + peak AC) from 28V/div to
2000 V/div
with up to 6000V offset.
(7600 V maximum measurable
differential voltage before saturation)
Differential Voltage
Range (Low Attenuation) 27.6 V (DC + peak AC) from 100 mV/div
to 6.9 V/div
with up to 150V offset.
27.6 V (DC + peak AC) from 100 mV/div
to 6.9 V/div
with up to 150V offset.
700 V (DC + peak AC) from 300mV/div
to 27.5 V/div
with up to 600V offset.
Common Mode Voltage
Range ±2000 V (DC + peak AC) ±2000 V (DC + peak AC) ±7600V (DC + peak AC), 6000 Vrms
Maximum Input Voltage
to Earth ±2000 Vpk
(nominal, either input to ground) ±2000 Vpk
(nominal, either input to ground) ±7600 Vpk
(nominal, either input to ground)
Max Safe Input Voltage 2000 V (DC + peak AC) CAT I *
1500 Vdc CAT III
1000 Vrms CAT III
2000 V (DC + peak AC) CAT I *
1500 Vdc CAT III
1000 Vrms CAT III
8485 V (DC + peak AC) CAT I *
6000 Vrms CAT I *
1500 Vdc CAT III
1000 Vrms CAT III
Sensitivity 100 mV/div to 6.9V/div (50X)
7V/div to 500V/div (500X) 100 mV/div to 6.9V/div (50X)
7V/div to 500V/div (500X) 300 mV/div to 27.5 V/div (200X)
28 V/div to 2000 V/div (2000X)
Gain Accuracy 1% (LF, guaranteed)
Slew Rate 400 V/ns (maximum) 270 V/ns (maximum) 1000 V/ns (typical)
Attenuation 50x / 500x 50x / 500x 200x / 2000x
Input Impedance 10 MΩ || 2.5 pF (between inputs)
5 MΩ || 5.0 pF (either input to ground) 10 MΩ || 2.5 pF (between inputs)
5 MΩ || 5.0 pF (either input to ground) 48 MΩ || 2.5 pF (between inputs)
24 MΩ || 5.0 pF (either input to ground)
Input Coupling DC only
Output Coupling AC or DC coupling
Output Termination 1 MΩ
Interface ProBus
Input Lead Length 40 cm input lead length
Cable Length (input lead
to oscilloscope
connection)
2.25 m 6.8 m 6.8 m
Noise and Rejection
CMRR (Typical) DC - 60 Hz: 85 dB
1 MHz: 65 dB
5 MHz: 40 dB
20 MHz: 30 dB
100 MHz: 30 dB
DC - 60 Hz: 85 dB
1 MHz: 65 dB
5 MHz: 40 dB
20 MHz: 30 dB
100 MHz: 30 dB
DC - 60 Hz: 85 dB
10 kHz: 70 dB
1 MHz: 64 dB (200x)
1 MHz: 50 dB (2000x)
10 MHz: 40 dB (200x)
10 MHz: 30 dB (2000x)
100 MHz: 30 dB
Noise (Probe) 50X: <30 mVrms
500X: <150 mVrms
(referred to input)
50X: <30 mVrms
500X: <150 mVrms
(referred to input)
200x: <65 mVrms
2000x: <320 mVrms
(typical, referred to input)
Environmental
Temperature (Operating) 0°C to 50°C
Temperature
(Non-Operating) -40°C to 70°C
Humidity (Operating) 5% to 80% RH (Non-Condensing) up to 30°C, decreasing linearly to 45% RH at 50°C
Humidity (Non-Operating) 5% to 95% RH (Non-Condensing), 75% RH above 30°C, 45% RH above 40°C
Altitude (Operating) 3000 m maximum
When used with clip accessories, 2000 m maximum
Altitude (Non-Operating) 10,000 m
Pollution Degree 2, Indoor use only
Certications
CE (LVD Directive
2006/95/EC) IEC/EN 61010-031:2015
CE (EMC Directive
2004/108/EC) IEC/EN 61326-1:2013
UL Listed UL 61010-031 (Second Edition)
cUL Listed CAN/CSA-C22.2 No. 61010-031-15
* CAT I per IEC/EN 61010-031/A1:2008. No Rated Measurement Category per IEC/EN 61010-031:2015.
SPECIFICATIONS
Product Description Product Code
1 kV, 25 MHz High Voltage Differential Probe with 2 m cable HVD3102A
1 kV, 120 MHz High Voltage Differential Probe with 2 m cable HVD3106A
1 kV, 80 MHz High Voltage Differential Probe with 6 m cable HVD3106A-6M
1 kV, 25 MHz High Voltage Differential Probe with 2 m cable without tip Accessories HVD3102A-NOACC
1 kV, 120 MHz High Voltage Differential Probe with 2 m cable without tip Accessories HVD3106A-NOACC
2 kV, 120 MHz High Voltage Differential Probe with 2 m cable HVD3206A
2 kV, 80 MHz High Voltage Differential Probe with 6 m cable HVD3206A-6M
6 kV, 100 MHz High Voltage Differential Probe with 6 m cable HVD3605A
High Voltage Replacement Accessories Kit (Includes 2 each, 1 Black, 1 Red):
Safety Alligator Clips, Plunger Pincer Clips, Plunger Hook Clips, Plunger Alligator Clips, Spade Terminals PK-HV-001
© 2018 by Teledyne LeCroy, Inc. All rights reserved. Specications, prices, availability, and delivery subject to change without notice.
Product or brand names are trademarks or requested trademarks of their respective holders. hvd3000a-probes-ds-14mar18
1-800-5-LeCroy
teledynelecroy.com
Local sales oces are located throughout the world.
Visit our website to nd the most convenient location.
Customer Service
Teledyne LeCroy oscilloscopes and probes are designed, built, and tested to ensure high reliability. In the unlikely event you experience difculties,
our digital oscilloscopes are fully warranted for three years and our probes are warranted for one year. This warranty includes:
No charge for return shipping Long-term 7-year support Upgrade to latest software at no charge
ORDERING INFORMATION
HVD3206/3206-6M
High Voltage
Differential Probe
HVD3605
High Voltage
Differential Probe
HVD310X-NOACC
High Voltage
Differential Probe
PK-HVA-05
PK-HVA-01 PK-HVA-04
PK-HVA-03PK-HVA-02 PK-HVA-06 PK-HVA-07
PK-HVA-05
PK-HVA-01 PK-HVA-04
PK-HVA-03PK-HVA-02 PK-HVA-06 PK-HVA-07
HVD310X/310X-6M
High Voltage
Differential Probe
PK-HVA-05
PK-HVA-01 PK-HVA-04
PK-HVA-03PK-HVA-02 PK-HVA-06 PK-HVA-07
PK-HVA-05
PK-HVA-01 PK-HVA-04
PK-HVA-03PK-HVA-02 PK-HVA-06 PK-HVA-07
HVD3605A
HVD310xA / 310xA-6M
HVD3206A / 3206A-6M
HVD310xA-NOACC
PK-HVA-01
Safety Alligator Clips
(Red/Black)
1000 V CAT III
PK-HVA-02
Plunger Pincer Clips
(Red/Black)
1000 V CAT II
PK-HVA-03
Plunger Hook Clips
(Red/Black)
1000 V CAT II
PK-HVA-04
Plunger Alligator Clips
(Red/Black)
1000 V CAT III
PK-HVA-05
Spade Terminals
(Red/Black)
1000 V CAT III
PK-HVA-06
6 KV Safety Alligator Clips
(Red/Black)
6000 V CAT I
PK-HVA-07
2 kV Plunger Alligator Clips
(Red/Black)
2000 V CAT I
HVD-A Probe Accessories