FIR-COMP-PM-UT4 - Lattice - Datasheet.Live

April 2014

IPUG79_01.4

FIR Filter IP Core User’s Guide

or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

IPUG79_01.4, April 2014 2 FIR Filter IP Core User’s Guide

Chapter 1. Introduction .......................................................................................................................... 4

Quick Facts ........................................................................................................................................................... 4

Features ................................................................................................................................................................ 7

Chapter 2. Functional Description ........................................................................................................ 8

Interface Diagram.................................................................................................................................................. 8

FIR Filter Architecture ........................................................................................................................................... 8

Direct-form Implementation.......................................................................................................................... 8

Symmetric Implementation........................................................................................................................... 9

Polyphase Interpolation FIR Filter................................................................................................................ 9

Polyphase Decimation FIR Filter................................................................................................................ 10

Multi-channel FIR Filters ............................................................................................................................ 10

Implementation Details........................................................................................................................................ 10

Configuring the FIR Filter IP Core....................................................................................................................... 11

Architecture Options................................................................................................................................... 11

I/O Specification Options............................................................................................................................ 13

Implementation Options ............................................................................................................................. 13

Signal Descriptions ............................................................................................................................................. 13

Interfacing with the FIR Filter IP core.................................................................................................................. 14

Data interface............................................................................................................................................. 14

Multiple Channels....................................................................................................................................... 14

Variable Interpolation/ Decimation Factor .................................................................................................. 15

Reloadable Coefficients ............................................................................................................................. 15

Timing Specifications .......................................................................................................................................... 16

Timing Specifications Applicable to All Devices......................................................................................... 16

Timing Specifications Applicable to LatticeXP2 and Certain LatticeECP3 Implementations ..................... 17

Timing Specifications Applicable to Certain LatticeECP3 Implementations............................................... 18

Timing specifications Applicable to ECP5 Implementations ...................................................................... 19

Chapter 3. Parameter Settings ............................................................................................................ 21

Architecture Tab.................................................................................................................................................. 23

Select ECP5 High Speed sysDSP Mode ................................................................................................... 23

Multi-channel.............................................................................................................................................. 23

Single-channel ........................................................................................................................................... 23

Number of Channels .................................................................................................................................. 23

Number of Taps ......................................................................................................................................... 23

Filter Type .................................................................................................................................................. 23

Interpolation Factor .................................................................................................................................... 23

Variable Interpolation Factor ...................................................................................................................... 23

Decimation Factor ...................................................................................................................................... 24

Variable Decimation Factor........................................................................................................................ 24

Reloadable Coefficients ............................................................................................................................. 24

Reorder Coefficients Inside........................................................................................................................ 24

Coefficients set........................................................................................................................................... 24

Symmetric Coefficients .............................................................................................................................. 24

Negative Symmetry.................................................................................................................................... 24

Half Band ................................................................................................................................................... 24

Coefficient Radix ........................................................................................................................................ 24

Coefficients File.......................................................................................................................................... 24

Multiplier Multiplexing Factor...................................................................................................................... 25

Number of sysDSP Blocks in a Row .......................................................................................................... 25

Table of Contents

IPUG79_01.4, April 2014 3 FIR Filter IP Core User’s Guide

I/O Specification Tab........................................................................................................................................... 25

Input Data Type.......................................................................................................................................... 25

Input Data Width ........................................................................................................................................ 25

Input Data Binary Point Position ................................................................................................................ 25

Coefficients Type ....................................................................................................................................... 26

Coefficients Width ...................................................................................................................................... 26

Coefficients Binary Point Position .............................................................................................................. 26

Output Width .............................................................................................................................................. 26

Output Binary Points .................................................................................................................................. 26

Overflow ..................................................................................................................................................... 26

Rounding.................................................................................................................................................... 26

Implementation Tab ............................................................................................................................................ 27

Data Memory Type..................................................................................................................................... 27

Coefficient Memory Type ........................................................................................................................... 27

Input Buffer Type........................................................................................................................................ 27

Output Buffer Type..................................................................................................................................... 27

Optimization ............................................................................................................................................... 27

Synchronous Reset (sr) ............................................................................................................................. 28

Clock Enable (ce)....................................................................................................................................... 28

Chapter 4. IP Core Generation and Evaluation .................................................................................. 29

Licensing the IP Core.......................................................................................................................................... 29

Getting Started .................................................................................................................................................... 29

IPexpress-Created Files and Top Level Directory Structure............................................................................... 34

Instantiating the Core .......................................................................................................................................... 35

Running Functional Simulation ........................................................................................................................... 35

Synthesizing and Implementing the Core in a Top-Level Design ....................................................................... 36

Hardware Evaluation........................................................................................................................................... 36

Enabling Hardware Evaluation in Diamond:............................................................................................... 36

Updating/Regenerating the IP Core .................................................................................................................... 36

Regenerating an IP Core in Diamond ........................................................................................................ 36

Regenerating an IP Core in Clarity Designer Tool ..................................................................................... 37

Recreating an IP Core in Clarity Designer Tool ......................................................................................... 37

Chapter 5. Support Resources ............................................................................................................ 39

Lattice Technical Support.................................................................................................................................... 39

E-mail Support ........................................................................................................................................... 39

Local Support ............................................................................................................................................. 39

Internet ....................................................................................................................................................... 39

LatticeXP2.................................................................................................................................................. 39

LatticeECP3 ............................................................................................................................................... 39

ECP5.......................................................................................................................................................... 39

Revision History .................................................................................................................................................. 39

Appendix A. Resource Utilization ....................................................................................................... 40

LatticeECP3 Devices .......................................................................................................................................... 40

Ordering Part Number................................................................................................................................ 40

LatticeXP2 Devices ............................................................................................................................................. 40

Ordering Part Number................................................................................................................................ 40

ECP5 Devices ..................................................................................................................................................... 41

Ordering Part Number................................................................................................................................ 41

IPUG79_01.4, April 2014 4 FIR Filter IP Core User’s Guide

The Lattice FIR (Finite Impulse Response) Filter IP core is a widely configurable, multi-channel FIR filter, imple-

mented using high performance sysDSP™ blocks available in Lattice devices. In addition to single rate filters, the

IP core also supports a range of polyphase decimation and interpolation filters. The utilization versus throughput

trade-off can be controlled by specifying the multiplier multiplexing factor used for implementing the filter. For exam-

ple, setting the multiplier multiplexing factor to the maximum value supported by the GUI results in the best

resource utilization, whereas setting the multiplier multiplexing factor to 1 results in the best throughput. The FIR

Filter IP core supports up to 256 channels, with each having up to 2048 taps.

The input data, coefficient and output data widths are configurable over a wide range. The IP core uses full internal

precision while allowing variable output precision with several choices for saturation and rounding. The coefficients

of the filter can be specified at generation time and/or reloadable during run-time through input ports.

The FIR Filter IP core can also be generated using the Lattice FIR Filter Simulink® Model. For information on the

Simulink flow, refer to the FPGA Design with ispLEVER tutorial.

Quick Facts

Table 1-1 through Table 1-2 give quick facts about the FIR Filter IP core for LatticeXP2™, LatticeECP3™, and

ECP5™ devices.

Table 1-1. FIR Filter IP Core for LatticeXP2 Devices Quick Facts

FIR IP Configuration

4 Channels

64Taps

1 Multiplier

1 Channel

32 Taps

32 Multipliers

1 Channel

32 Taps

8 Multipliers

Core

Requirements

FPGA Families Supported LatticeXP2

Minimal Device Needed LFXP2-5E LFXP2-40E LFXP2-8E

Resource

Utilization

Targeted Device LFXP2-40E-7F672C

LUTs 96 311 163

sysMEM EBRs 1 0 8

Registers 114 322 252

MULT18X18 1 32 8

Design Tool

Support

Lattice Implementation Lattice Diamond® 3.2

Synthesis Synopsys® Synplify Pro® for Lattice 2013.09L-SP1

Simulation Aldec® Active-HDL™ 9.2 Lattice Edition

Mentor Graphics® ModelSim® SE 6.3F

Chapter 1:

Introduction

IPUG79_01.4, April 2014 5 FIR Filter IP Core User’s Guide

Table 1-2. FIR Filter IP Core for LatticeECP3 Devices Quick Facts

FIR IP Configuration

4 Channels

64 Taps

1 Multiplier

1 Channel

32 Taps

32 Multipliers

1 Channel

32 Taps

8 Multipliers

Core

Requirements

FPGA Families Supported Lattice ECP3

Minimal Device Needed LFE3-35EA

Resource

Utilization

Targeted Device LFE3-70E-8FN672CES

LUTs 150 48 132

sysMEM EBRs 2 0 8

Registers 174 98 432

DSP Slice 2 16 5

Design Tool

Support

Lattice Implementation Lattice Diamond 3.3

Synthesis Synopsys Synplify Pro for Lattice D-2013.09L-SP1

Simulation Aldec Active-HDL 9.2 Lattice Edition

Mentor Graphics ModelSim SE 6.3F

Table 1-3. FIR Filter IP Core (Low-Speed Mode) for ECP5 Devices Quick Facts

FIR IP Configuration

4 Channels

64 Taps

1 Multiplier

1 Channel

32 Taps

32 Multipliers

1 Channel

32 Taps

8 Multipliers

Core

Requirements

FPGA Families Supported ECP5

Minimal Device Needed LFE5U-45FEA

Resource

Utilization

Targeted Device LFE5U-85F-8MG756I LFE5U-85F-8MG756I LFE5U-85F-8MG756I

LUTs 143 47 133

sysMEM EBRs 2 0 8

Registers 174 98 432

DSP Slice 2 16 5

Design Tool

Support

Lattice Implementation Lattice Diamond 3.2

Synthesis Synopsys Synplify Pro F-2013.09L-beta

Simulation Aldec Active-HDL 9.2 Lattice Edition

Mentor Graphics ModelSim SE PLUS 6.3f

Introduction

IPUG79_01.4, April 2014 6 FIR Filter IP Core User’s Guide

In high-speed mode, for partially-folded/full-folded cases, 1 channel means I,Q channels.

Table 1-4. FIR Filter IP Core (High-Speed Mode) for ECP5 Devices Quick Facts

FIR IP Configuration

1 Channels

64 Taps

16 Multipliers

1 Channel

24 Taps

6 Multipliers

1 Channel

48 Taps

12 Multipliers

Core

Requirements

FPGA Families Supported ECP5

Minimal Device Needed LFE5U-45FEA

Resource

Utilization

Targeted Device LFE5U-85F-8MG756I LFE5U-85F-8MG756I LFE5U-85F-8MG756I

LUTs 737 372 633

sysMEM EBRs 24 9 18

Registers 1018 643 929

DSP Slice 10 5 8

Design Tool

Support

Lattice Implementation Lattice Diamond 3.2

Synthesis Synopsys Synplify Pro F-2013.09L-beta

Simulation Aldec Active-HDL 9.2 Lattice Edition

Mentor Graphics ModelSim SE PLUS 6.3f

Introduction

IPUG79_01.4, April 2014 7 FIR Filter IP Core User’s Guide

Features

• Variable number of taps up to 2048

• Input and coefficients widths of 4 to 32 bits

• Multi-channel support for up to 256 channels

• Decimation and Interpolation ratios from 2 to 256

• Support for half-band filter

• Configurable parallelism from fully parallel to serial

• Signed or unsigned data and coefficients

• Coefficients symmetry and negative symmetry optimization

• Re-loadable coefficients support

• Full precision arithmetic

• Selectable output width and precision

• Selectable overflow: wrap-around or saturation

• Selectable rounding: truncation, round towards zero, round away from zero, round to nearest and convergent

rounding

• Width and precision specified using fixed point notations

• Handshake signals to facilitate smooth interfacing

• In ECP5, support high-speed. For low speed, support for half-band filter

IPUG79_01.4, April 2014 8 FIR Filter IP Core User’s Guide

This chapter provides a functional description of the FIR Filter IP core.

Interface Diagram

The top-level interface diagram for the FIR Filter IP core is shown in Figure 2-1.

Figure 2-1. Top-Level Interface for the FIR Filter IP Core

FIR Filter Architecture

FIR filter operation on data samples can be described as a sum-of-products operation. For an N-tap FIR filter, the

current input sample and (N-1) previous input samples are multiplied by N filter coefficients and the resulting N

products are added to give one output sample as shown below.

(1)

In the above equation hn, n=0,1,…,N-1 is the impulse response, xn, n=0,1,…,×, is the input and yn, n=0,1,…,×, is

the output. The number of delay elements (N-1) represents the order of the filter. The number of input data samples

(current and previous) used in the calculation of one output sample represents the number of filter taps (N).

Direct-form Implementation

In the direct-form implementation shown in Figure 2-2, the input samples will be shifted into a shift register queue

and each shift register is connected to a multiplier. The products from the multipliers are summed to get the FIR fil-

ter’s output sample.

FIR Filter IP

clk

rstn

ibstart

inpvalid

coeffwe

coeffset

coeffin

iin

qin

rfi

din

ifactor

dfactor

factorset

obstart

outvalid

iout

qout

dout

CONTROL SIGNALS

DATA INPUT

DATA OUTPUT

11110

...

+++==

NNnnn

iinn

hxhxhxhx

Chapter 2:

Functional Description

IPUG79_01.4, April 2014 9 FIR Filter IP Core User’s Guide

Figure 2-2. Direct-form FIR Filter

Symmetric Implementation

The impulse response for most FIR filters is symmetric. This symmetry can generally be exploited to reduce the

arithmetic requirements and produce area-efficient filter realizations. It is possible to use only one half of the multi-

pliers for symmetric coefficients compared to that used for a similar filter with non-symmetric coefficients. An imple-

mentation for symmetric coefficients is shown in Figure 2-3.

Figure 2-3. Symmetric Coefficients FIR Filter Implementation

Polyphase Interpolation FIR Filter

The polyphase interpolation filter option implements the computationally efficient 1-to-P interpolation filter shown

below where P is an integer greater than 1. Figure 2-4 shows a polyphase interpolator, where each branch is

referred to as a polyphase.

Figure 2-4. Polyphase Interpolator

In this structure, the input data will be loaded into each poly-phase at the same time and the output data of each

polyphase will be unloaded as an output sample of the FIR. The number of polyphases is equal to the interpolation

factor. The coefficients are assigned to all polyphases evenly.

Din

H(0) H(1) H(2) H(n-1)

Dout

-1

XXXX

-1

X X X

Din

H(0) H(1) H(2) H(n/2)

Dout

++ + +

-1

Polyphase 1

Polyphase 2

Polyphase P-1

Polyphase P

Din Dout

Functional Description

IPUG79_01.4, April 2014 10 FIR Filter IP Core User’s Guide

Polyphase Decimation FIR Filter

The polyphase decimation filter option implements the computationally efficient P-to-1 decimation filter shown in

Figure 2-5, where P is an integer greater than 1.

Figure 2-5. Polyphase Decimator

In this structure, the input sample is loaded sequentially into each of the polyphases with only one polyphase fed at

a time. When all the polyphases are loaded with a sample, the result from the polyphases are summed and

unloaded as the FIR filter's output. In this scheme, P input samples generate one output sample, where P is the

decimation factor.

Multi-channel FIR Filters

It is very common to see FIR filters used in multi-channel processing scenarios. The maximum possible throughput

of a FIR filter implementation is often much higher than the throughput required for a single channel being pro-

cessed. For such applications, it is desirable to use the same resources in a time multiplexed way to realize multi-

channel FIR filters. Except in fully parallel implementations, where enough multipliers are used to perform all the

necessary computations in one clock cycle, the FIR filter uses independent tap and coefficient memories to feed

each multiplier. Hence, multi-channel implementations result in lower memory usage compared to multiple instanti-

ations of FIR filters. For cases, where all the channels use the same coefficient set, using a multi-channel FIR filter

has the clear advantage of requiring smaller coefficient memories.

Implementation Details

Figure 2-6 shows the functional block diagram of the FIR Filter IP core.

Figure 2-6. Functional Block Diagram of the FIR Filter IP Core

The data and coefficients are stored in different memories shown as tap memory and coefficients memory in the

above diagram. The symmetry adder is used if the coefficients are symmetric. The multiplier array contains one or

more multipliers depending on the user specification. The adder tree performs the sum of products. Depending on

the configuration, the adder tree, or a part of it, is implemented inside DSP blocks. The output processing block

performs the output width reduction and precision control. This block contains logic to support different types of

Din +Dout

Polyphase 1

Polyphase 2

Polyphase P-1

Polyphase P

din dout

Symmetry

Adder

Input

Registers

Ta p

Memory

Multiplier

Array

Coefficient

Memory

Adder

Tree

Output

Processing

coeffin

Control Logic

inpvalid

ifactor

dfactor

factorset

outvalid

rfi

obstart

coeffwe

coeffset

ibstart

Functional Description

IPUG79_01.4, April 2014 11 FIR Filter IP Core User’s Guide

rounding and overflow. The block labeled “Control Logic” manages the scheduling of data and arithmetic opera-

tions based on the type of filter (interpolation, decimation or multi-channel) and multiplier multiplexing.

The tap and coefficient memories are managed differently for different configurations of the FIR filter. Figure 2-7

shows the memory assignments for a 16-tap, 3-channel, symmetric FIR filter with two multipliers.

Figure 2-7. Tap and Coefficient Memory Management for a Sample FIR Filter

In the diagram, there are two tap memories and a coefficient memory for each multiplier. The depth of each mem-

ory is ceil(taps/multiplier)*channel, where the operator, ceil(x), returns the next higher integer if the argument x is

fractional. The memory depth is 12 in this example.

Configuring the FIR Filter IP Core

Architecture Options

The options for number of channels, number of taps and filter type are independent and directly specified in the

Architecture tab of the IP core GUI (see “Parameter Settings” on page 21 for details). If a polyphase decimator or

interpolator is required, the decimation or interpolation factor can be directly specified in the GUI. The decimation

or interpolation factor can also be specified through input ports during operation by selecting the corresponding

Variable option. If the Variable decimation (or Variable interpolation) factor option is selected, the decimation (or

interpolation) factor can be varied from two to Decimation factor (or Interpolation factor) through the input port.

Coefficients Specification

The coefficients of the filter are specified using a coefficients file. The coefficients file is a text file with one coeffi-

cient per line. If the coefficients are symmetric, the check box Symmetric Coefficients must be checked so the IP

core uses symmetry adders to reduce the number of multipliers used. If the Symmetric Coefficients box is

checked, only one-half of the coefficients are read from the coefficient file. For an n-tap symmetric coefficients filter,

the number of coefficients read from the coefficients file is equal to ceil(n/2). For multi-channel filters, the coeffi-

cients for channel 0 are specified first, followed by those for channel 1, and so on. For multi-channel filters, there is

an option to specify whether the coefficients are different for each channel or the same (common) for all the chan-

nels. If the coefficients are common, only one set of coefficients needs to be specified in the coefficients file. The

coefficient values in the file can be in any radix (decimal, hexadecimal or binary) selected by the user. A unary neg-

ative operator is used only if the coefficients are specified in decimal radix. For hexadecimal and binary radices, the

numbers must be represented in twos complement form. An example coefficients file in decimal format for an 11-

tap, 16-bit coefficients set is given below. In this example, the coefficients binary point is 0.

Channel0

Channel1

Channel2

MAC

Tap Memory

Coefficients

Memory

Adder

Tree

Multipliers

Symmetry

Adder

Symmetry

Adder

Coefficients

Memory

Functional Description

IPUG79_01.4, April 2014 12 FIR Filter IP Core User’s Guide

-556

-706

-857

-419

1424

5309

11275

18547

25649

30848

32758

An example coefficients file in floating point format for the above case when the Coefficients binary point position is

8, is given below. The coefficients will be quantized to conform to the 16.8 fractional number, in which 16 is the full

width of the coefficients and 8 is the width of the fractional part.

-2.1719

-2.7578

-3.3477

-1.6367

5.5625

20.7383

44.043

72.45

100.0191

120.5

127.96

If the check box Reloadable Coefficients is checked, the coefficients can be reloaded to the FIR filter during the

operation of the core. With this option, the desired coefficients must be loaded before the operation of the filter. The

coefficients must be loaded in a specific order that is determined by the program supplied with the IP core. The IP

core can also optionally do the reordering internally, albeit using more resources. If this option is desired, the check

box Reorder Coefficients Inside can be checked. With this option, the coefficients can be loaded in the normal

sequential order to the core.

Multiplier Multiplexing Factor

The throughput and the resource utilization can be controlled by assigning a proper value to the Multiplier Multi-

plexing Factor parameter. Full parallel operation (one output data per clock cycle) can be achieved by setting the

Multiplier Multiplexing Factor to 1. If the Multiplier Multiplexing Factor is set to the maximum value displayed in

the GUI, full series operation is supported and it takes up to n clocks to compute one output data sample, where n

is the number of taps for a non-symmetric FIR filter and half the number of taps for a symmetric FIR filter. The max-

imum value of the Multiplier Multiplexing Factor for different configurations of an n-tap FIR filter is given in

Table 2-1.

Table 2-1. Maximum Multiplier Multiplexing Factor for Different Configurations1

FIR Type Single Rate Interpolator with Factor=i Decimator with Factor=d

Non-symmetric n Ceil(n/i) Ceil(n/d)

Symmetric Ceil(n/2) Ceil(n/2i) Ceil(n/2d)

Half-band floor((n+1)/4)+1 floor((n+1)/4) floor((n+1)/8)+1

1. The operator floor (x) returns the next lower integer, if x is a fractional value.

Functional Description

IPUG79_01.4, April 2014 13 FIR Filter IP Core User’s Guide

I/O Specification Options

The controls in the I/O Specifications GUI tab are used to define the various widths and precision methods in the

data path. The width and binary point positions of the input data and coefficients can be defined independently.

From the input data width, coefficient width and the number of taps, the full precision output width and true location

of the output binary point automatically get fixed. The full precision output is converted to user specified output

width by dropping some least significant (LS) and some most significant (MS) bits and by performing the specified

rounding and overflow processing. The output is specified by the output width and the output binary point position

parameter.

Rounding

The following five options are supported for rounding:

•None – Discards all bits to the right of the output least significant bit and leaves the output uncorrected.

•Rounding up – Rounds to nearest more positive number.

•Rounding away from zero – Rounds away from zero if the fractional part is exactly one-half.

•Rounding towards zero – Rounds towards zero if the fractional part is exactly one-half.

•Convergent rounding – Rounds to the nearest even value if the fractional part is exactly one-half.

Implementation Options

Memory Type

The FIR Filter IP core uses memories for storing delay tap data, coefficients and for some configurations, input or

output data. The number of memory units used depends on several parameters including data width, number of

taps, filter type, number of channels and coefficient symmetry. In most cases, each multiplier requires one data

memory unit and one coefficient memory unit. Interpolation or decimation filters may additionally use input or out-

put buffers. The memory type GUI option can be used to specify whether EBR or distributed memory is used for

data, coefficient, input and output storage. The option called “Auto” leaves that choice to the IP generator tool,

which uses EBR if the memory is deeper than 128 locations and distributed memory otherwise.

Signal Descriptions

A description of the Input/Output (I/O) ports for the FIR Filter IP core is provided in Table 2-2. The top-level inter-

face diagram for the FIR Filter IP core is shown in Figure 2-1.

Table 2-2. Top-Level Port Definitions

Port Bits I/O Description

General I/Os

clk 1ISystem clock for data and control inputs and outputs.

rstn 1ISystem wide asynchronous active-low reset signal.

din Input data width IInput data.

iin

Input data width

II channel input data for High Speed mode. In single channel high speed

mode, interleaved data feed into the core from iin and qin, while data on

iin is d0,d2,d4,d6... and d1,d3,d5,d7 are on qin. In multi-channel high

speed mode, iin and qin are data for different channel.

qin Input data width IQ channel input data for High Speed mode. As above.

inpvalid 1IInput valid signal. The input data is read-in only when inpvalid is high.

dout Output width OOutput data for Low speed mode.

iout

Output width

OOutput data for high speed mode, in single channel mode, interleaved

data out from the core, while d0,d2,d4,d6 are on iout, and d1,d3,d5,d7

are on qout. In mult-channel mode, data on iout and qout are for different

channel.

qout Output width OQ channel output data in high speed mode.

Functional Description

IPUG79_01.4, April 2014 14 FIR Filter IP Core User’s Guide

Interfacing with the FIR Filter IP core

Data interface

In low speed mode, data is feed into the core through din and out from the core through dout. In high speed mode,

data is feed into the core through iin&qin while out from the core through iout&qout, and in single channel mode,

the data on iin&qin/iout&qout is interleaved.

Multiple Channels

For multi-channel implementations, two ports, ibstart and obstart, are available in the IP core to synchronize the

channel numbers. The input ibstart is used to identify channel 0 data applied at the inputs. The output obstart goes

high simultaneously with channel 0 output data.

outvalid 1OOutput data qualifier. Output data dout is valid only when this signal is

high.

rfi

OReady for input. This output, when high, indicates that the IP core is

ready to receive the next input data. A valid data may be applied at din

only if rfi was high during the previous clock cycle.

When Reloadable coefficients is selected

coeffin

Notes 1

ICoefficients input. The coefficients have to be loaded through this port in

a specific order. Refer to the section “Interfacing with the FIR Filter IP

core” for details.

coeffwe 1IWhen asserted, the value on bus coeffin will be written into coefficient

memories.

coeffset

IThis input is used to signal the filter to use the recently loaded coefficient

set. This signal must be pulsed high for one clock cycle after the loading

the entire coefficient set using coeffin and coeffwe.

When Number of channels is greater than 1

ibstart 1IInput block start. For multi-channel configurations, this input identifies

channel 0 of the input.

obstart 1 OOutput block start. For multi-channel configurations, this output identifies

channel 0.

When Variable interpolation factor or Variable decimation factor is checked

ifactor ceil(Log2(Interpolation

factor+1))

IInterpolation factor value

dfactor ceil(Log2(Decimation

factor+1))

IDecimation factor value

factorset 1ISets the interpolation factor or the decimation factor.

Optional I/Os

ce 1IClock Enable. While this signal is de-asserted, the core will ignore all

other synchronous inputs and maintain its current state

sr 1ISynchronous Reset. When asserted for at least one clock cycle, all the

registers in the IP core are initialized to reset state.

Notes 1

a. Width for signed type and symmetric interpolation is Coefficients width +1.

b. Width for unsigned and symmetric interpolation is Coefficients width +2.

c. Width for all other cases is Coefficients width.

Table 2-2. Top-Level Port Definitions

Port Bits I/O Description

Functional Description

IPUG79_01.4, April 2014 15 FIR Filter IP Core User’s Guide

Variable Interpolation/ Decimation Factor

When the interpolation (or decimation) factor is variable, the ports ifactor (or dfactor) and factorset are added to the

IP core. The interpolation (or decimation) factor applied on the port ifactor (or dfactor) is set when the strobe signal

factorset is high. When the interpolation (or decimation) factor changes, the output rfi goes low for a few cycles.

When it becomes high again, the filter performs as an interpolating (or decimating) filter corresponding to the new

factor value.

Reloadable Coefficients

When Reloadable Coefficients is selected, the two added ports, coeffin and coeffwe, are used to reload the coef-

ficients. All the coefficients need to be loaded in one batch, while keeping the signal coeffwe high during the entire

duration of loading. After all the coefficients are loaded, the input signal coeffset must be pulsed high for one clock

cycle for the new coefficients to take effect.

There are two ways in which coefficients can be applied for reloading the coefficients memory, as specified by the

Reorder Coefficients Inside parameter.

When Reorder Coefficients Inside is not selected, the coefficients have to be applied in a particular sequence for

reloading the coefficients memory. The raw coefficients, as specified in the coefficients file, can be converted to the

reloadable sequence by using the coefficients generation program coeff_gen.exe (for Windows) available under the

“gui” folder in the IP installation directory (for example, under the C:\LatticeCore\fir_core_v4.2\gui

folder). The names of the coefficient generation program for UNIX and Linux are coeff_gen_s and coeff_gen_l

respectively. For Windows, the program is invoked as follows:

coeff_gen.exe <IP_file_name>.lpc

Note: If in lpc file, the value of parameter "varcoeff=" is "Yes", please change it to "No " before g enerating ROM files

manually.

This command converts the coefficients in the input file1, as referred by the coefffile= parameter in the lpc file, to the

loadable coefficients sequence file called coeff.mem. Note that the output file may contain more coefficients than

there originally were due to inserted zero coefficients. All the coefficients in the output file, including the zeros, have

to be applied sequentially through the coeffin port. To obtain the sequence of application of coefficients, edit the

input coefficients file with sequential numbers 1,2,… and run the coeff_gen.exe command. In the reloadable coeffi-

cients mode, the core will not be ready for operation (the rfi output will not be high) until the coefficients are loaded

and coeffset is asserted high.

When the parameter Reorder Coefficients Inside is selected, the coefficients will be reordered inside the IP core

without requiring manual reordering described previously. With this option, reordering logic is added to the IP core

and the user can apply the coefficients in the normal sequence.

With this capability, if the parameter Symmetric Coefficients is selected, only half of the coefficients provided will

be used. For example, if the raw coefficient input sequence is: "1 2 3 4 5 6 5 4 3 2 1," the coefficients that will be

used will be "1 2 3 4 5 6."

Similarly, if Half Band is selected with the this capability, all of the input coefficients in even locations, except the

last one, will be discarded. For example, if the raw coefficient input sequence is: "1 0 2 0 3 0 4 0 5 6 5 0 4 0 3 0 2 0

1," the coefficients that will be used will be "1 2 3 4 5 6."

1. If the parameter varcoeff= in the lpc file is set to "yes", change it to "no" before generating the new coefficients file.

Functional Description

IPUG79_01.4, April 2014 16 FIR Filter IP Core User’s Guide

Timing Specifications

Timing diagrams for the FIR Filter IP core are given in Figure 2-8 through Figure 2-21. Note that there are different

timing specifications for certain FIR filter applications using LatticeECP3 devices. Figures 2-8 through 2-11 apply

to all FIR applications. Figures 2-12 through 2-14 apply to all FIR applications using LatticeXP2 devices and the

following applications using LatticeECP3 devices: negative symmetry, half band, factor variable interpolation and

decimation and applications using 36x36 multipliers. Figures 2-15 through 2-17 apply to all other LatticeECP3

applications. Figure 2-18 through 2-21 apply to High Speed mode using ECP5.

Timing Specifications Applicable to All Devices

Figure 2-8. Single Channel, Single Rate FIR Filter with Continuous Inputs

Figure 2-9. Single Channel, Single Rate FIR Filter with Gaps in Input

Figure 2-10. Factorset Signals

Figure 2-11. Coefficient Reloading

d0 d1 d2 d3 d4 d5 d6 d7 d8 d9 d10 d11 d12 d13 d14 d15 d16 d17 d18 d19

D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15

rfi

inpvalid

din

outvalid

dout

clk

d0 d1 d2 d3 d4 d5 d6 d7 d8 d9 d10 d11

D0 D1 D2 D3 D4 D5 D6 D7 D8 D9

outvalid

dout

inpvalid

rfi

din

clk

factorset

Ifactor/

dfactor

clk

c0 c1 c2 c3 c4 c5 c6 …... cn

coeffwe

coeffin

coeffset

Functional Description

IPUG79_01.4, April 2014 17 FIR Filter IP Core User’s Guide

Timing Specifications Applicable to LatticeXP2 and Certain LatticeECP3 Implementa-

tions

As indicated previously, Figures 2-12 through 2-14 apply to all FIR applications using LatticeXP2 devices and the

following applications using LatticeECP3 devices: negative symmetry, half band, factor variable interpolation and

decimation and applications using 36x36 multipliers.

Figure 2-12. Multi-Channel Single Rate FIR Filter (3 Channels)

Figure 2-13. Multi-Channel (3 Channels) Interpolator (Factor of 3)

Figure 2-14. Multi-Channel (3 Channels) Decimator (Factor of 3)

clk

inpvalid

rfi

ibstart

d00 d10din d20 d01 d11 d21 d02 d12 d22 d03

D00 D10 D20 D01 D11 D21 D02 D12

outvalid

obstart

dout

clk

rfi

inpvalid

ibstart

d00din d10 d20 d01 d11 d21 d02

outvalid

obstart

D00 D10 D20 D01 D11 D21 D02 D12 D22 D03 D13 D23 D04 D14 D24 D05dout

clk

inpvalid

rfi

ibstart

d00 d10din d20 d01 d11 d21 d02 d12 d22 d03

D00

outvalid

obstart

dout D10 D20 D01

Functional Description

IPUG79_01.4, April 2014 18 FIR Filter IP Core User’s Guide

Timing Specifications Applicable to Certain LatticeECP3 Implementations

As indicated previously, Figures 2-15 through 2-17 apply to all LatticeECP3 applications other than those specifi-

cally listed in the previous section.

Figure 2-15. Multi-Channel Single Rate FIR Filter (3 Channels)

Figure 2-16. Multi-Channel (3 Channels) Interpolator (Factor of 3)

Figure 2-17. Multi-Channel (3 Channels) Decimator (Factor of 3)

clk

ibstart

rfi

inpvalid

d00din d10 d20 d01 d11 d21 d02 d12 d22 d03

outvalid

obstart

D00 D10 D20 D01 D11 D21 D02 D12dout D12

clk

rfi

inpvalid

ibstart

d00din d10 d20 d01 d11 d21 d02

outvalid

obstart

D00 D10 D20 D01 D11 D21 D02 D12 D22 D03 D13 D23 D04 D14 D24 D05dout

clk

d00 d10 d20 d01 d11 d21 d02 d12 d22 d03 d13

D00

outvalid

obstart

dout D10 D20 D01

Functional Description

IPUG79_01.4, April 2014 19 FIR Filter IP Core User’s Guide

Timing specifications Applicable to ECP5 Implementations

As indicated previously, Figures 2-18 through 2-21 apply to ECP5 High speed mode application.

Figure 2-18. Single Channel in High Speed Mode

Figure 2-19. Multi-Channel (4 Channels) in High Speed Mode

CLK

qin

outvalid

iout

qout

rfi

inpvalid

d0 d2 d4 d6 d8

d1 d3 d5 d7 d9

dn -5 dn -3 dn -1

dn -4 dn -2 dn

iin

D0 D2

D1 D3

D4 D6

D5 D7

Dn -1

CLK

qin

outvalid

obstart

iout

qout

rfi

inpvalid

di 00 di 10 di 20 di 30

iin di 01 di 11

Di10 Di20

di 21 di 31

Di30

dq00 dq10 dq20 dq30 dq01 dq11 dq21 dq31

ibstart

Di00

Dq10 Dq20 Dq30Dq00

Functional Description

IPUG79_01.4, April 2014 20 FIR Filter IP Core User’s Guide

Figure 2-20. Multi-Channel (2 Channels) DHIGHSPEED I&Q Polyphase-Interpolator (1:4)

Figure 2-21. Multi-Channel (2 Channels) DHIGHSPEED I&Q Polyphase-Decimator (4:1)

c00 c01 c10 c11 c131

CLK

coeffwe

coeffin

coeffset

rfi

inpvalid

ibstart

di 00 di 10 di 01 di 11 di 02

dq00 dq10 dq01 dq11 dq02

iin

qin

outvalid

obstart

Di00 Di10 Di01 Di11 Di 02 Di 12 Di 03 Di 13 Di 04 Di14 Di05 Di15 Di06 Di16

Dq00 Dq10 Dq01 Dq11 Dq02 Dq12 Dq03 Dq13 Dq04 Dq14 Dq05 Dq15 Dq06 Dq16

iout

qout

c00 c01 c10 c11 c131

CLK

coeffwe

coeffin

coeffset

rfi

inpvalid

ibstart

di13 di04 di17

iin

qin

outvalid

obstart

Di00 Di10 Di01 Di11

iout

qout

di00 di10 di01 di11 di02 di12 di03 di16 di07di14 di05 di15 di06

di13 di04 di17di00 di10 di01 di11 di02 di12 di03 di16 di07di14 di05 di15 di06

Dq00 Dq10 Dq01 Dq11

IPUG79_01.4, April 2014 21 FIR Filter IP Core User’s Guide

The IPexpress and Clarity Designer tools are used to create IP and architectural modules in the Diamond software.

Refer to “IP Core Generation and Evaluation” on page 29 for a description on how to generate the IP.

Table 3-1 provides the list of user configurable parameters for the FIR Filter IP core The parameter settings are

specified using the FIR Filter IP core Configuration GUI in IPexpress or Clarity Designer. The numerous FIR Filter

IP core parameter options are partitioned across multiple GUI tabs as described in this chapter.

Table 3-1. Parameter Specifications for the FIR Filter IP Core

Parameter Range Default

Filter Specifications

Number of channels 1 to 256 4

Number of taps 1 to 2048 64

Filter type {Single rate, Interpolator, Decimator} Single rate

Interpolation factor 2 to 256 2

Variable interpolation factor {Yes, No} No

Decimation factor 2 to 256 2

Variable decimation factor {Yes, No} No

Single channel in High Speed {Yes, No} No

Multi-channel in High Speed {Yes, No} No

Coefficients Specifications

Reloadable coefficients {Yes, No} Yes

Reorder coefficients inside {Yes, No} No

coefficients set {Common, One per channel} Common

Symmetric coefficients {Yes, No} No

Negative symmetry {Yes, No} No

Half band {Yes, No} No

Coefficient radix {Floating point, Decimal, Hex, Binary} Decimal

Coefficients file Type or Browse -

Advanced Options

Multiplier Multiplexing factor Note 2, Note 3 Note 3

Number of SysDSP blocks in a row 54Note 4

I/O Specifications

Input data type {Signed, Unsigned} Signed

Input data width 4 to 32 16

Input data binary point position -2 to Input data width + 2 0

Coefficients type {Signed, Unsigned} Signed

Coefficients width 4 to 32 16

Coefficients binary point position -2 to Coefficients width + 2 0

Output width 4 to Max Output Width 38

Output binary point position

(4+Input data binary point position + coefficient binary point posi-

tion – Max output width) to (Output width + Input data binary point

position + Coefficient binary point position - 4)

Chapter 3:

Parameter Settings

IPUG79_01.4, April 2014 22 FIR Filter IP Core User’s Guide

The default values shown in the following pages are those used for the FIR Filter reference design. IP core options

for each tab are discussed in further detail.

Precision control

Overflow {Saturation, Wrap-around} Saturation

Rounding {None, Round-up, Round away from zero, Round towards zero,

Convergent rounding} None

Memory Type

Data memory type {EBR, Distributed, Auto} EBR

Coefficient memory type {EBR, Distributed, Auto} EBR

Input buffer type {EBR, Distributed, Auto} EBR

Output buffer type {EBR, Distributed, Auto} EBR

Optimization {Area, Speed} {Area}

Optional Ports

ce {Yes, No} No

sr {Yes, No} No

Synthesis Options

Frequency constraint 1 – 400 300

2. The Multiplier Multiplexing Factor is limited by the number of DSP blocks in a device (A) and the actual number of DSP blocks a design

needs (B). When A>B, the Multiplier Multiplexing Factor is set to 1; otherwise the value will be greater than 1.

3. See “Multiplier Multiplexing Factor” on page 25 for details.

4. Maximum number of DSP blocks available in a row in the selected device.

Table 3-1. Parameter Specifications for the FIR Filter IP Core (Continued)

Parameter Range Default

Parameter Settings

IPUG79_01.4, April 2014 23 FIR Filter IP Core User’s Guide

Architecture Tab

Figure 3-1 shows the contents of the Architecture tab.

Figure 3-1. Architecture Tab of the FIR Filter IP Core GUI

Select ECP5 High Speed sysDSP Mode

This option allows users to select whether to use high speed mode or not.

Multi-channel

This option allows users to specify whether the filter should be a multiple channels filter in high speed mode

Single-channel

This option allows users to specify whether the filter should be a single channel filter in high speed mode.

Number of Channels

This option allows the user to specify the number of channels.

Number of Taps

This option allows the user to specify the number of taps.

Filter Type

This option allows the user to specify whether the filter is single rate, interpolator or decimator.

Interpolation Factor

This option allows the user to specify the value of the fixed interpolation factor. When FIR type is interpolation, the

value should be 2 to 256, otherwise, it will be set to 1 automatically.

Variable Interpolation Factor

This option allows the user to specify whether the interpolation factor is fixed at the time of IP generation or variable

during run-time. If this is checked, the interpolation factor is set through the input port ifactor when factorset is high.

Parameter Settings

IPUG79_01.4, April 2014 24 FIR Filter IP Core User’s Guide

Decimation Factor

This option allows the user to specify the value of the fixed decimation factor. When FIR type is decimation, the

value should be 2 to 256, otherwise, it will be set to 1 automatically.

Variable Decimation Factor

This option allows the user to specify whether the decimation factor is fixed at the time of IP generation or variable

during run-time. If this is checked, the decimation factor is set through the input port dfactor when factorset is high.

Reloadable Coefficients

This option allows the user to specify whether the coefficients are fixed or reloadable. If checked, the coefficients

can be reloaded during core operation using the input port coeffin.

Reorder Coefficients Inside

When coefficients are reloadable, they need to be entered in a particular order. The reordering can be done using

the program supplied along with the IP core. However, the core also provides for optional hardware reordering at

the expense of additional hardware resources. If this option is selected, the coefficients can be entered in the nor-

mal sequence to the core and the core will internally reorder hem as required. This option is not available when Fil-

ter type is interpolator and Symmetric coefficients is enabled.

Coefficients set

This option allows the user to specify whether the same coefficient set is used for all channels or an independent

coefficient set is used for each channel.

Symmetric Coefficients

This option allows the user to specify whether the coefficients are symmetric. If this is checked only one half of the

number of coefficients (if number of taps is odd, the half value is rounded to the next higher integer) is read from

the initialization file.

Negative Symmetry

If this is checked, the coefficients are considered to be negative symmetric. That is the second half of the coeffi-

cients are made equal to the negative of the corresponding first-half coefficients.

Half Band

This option allows the user to specify whether a half band filter is realized. If this is checked only one half of the

number of coefficients (if the number of taps is odd, the half value is rounded to the next higher integer) is read

from the initialization file.

Coefficient Radix

This option allows the user to specify the radix for the coefficients in the coefficients file. For decimal radix, the neg-

ative values have a preceding unary minus sign. For hexadecimal (Hex) and binary radices, the negative values

must be written in 2’s complement form using exactly as many digits as specified by the coefficients width parame-

ter. The floating point coefficients are specified in the form <nn…n>.<dd…d>, where the digits 'n' denote the inte-

ger part and the digits 'd', the decimal part. The values of the floating point coefficients must be consistent with the

Coefficients width and Coefficients binary point position parameters. For example, if <nn...n>.<dd...d>is 8.4 and

Coefficients type is unsigned, the value of the coefficients should be between 0 and 11111111.1111 (255.9375).

Coefficients File

This option allows the user to specify the name and location of the coefficients file. If the coefficients file is not

specified, the filter is initialized with a default coefficient set.

Parameter Settings

IPUG79_01.4, April 2014 25 FIR Filter IP Core User’s Guide

Multiplier Multiplexing Factor

This option allows the user to specify the Multiplier Multiplexing Factor. This parameter should be set to 1 for full

parallel applications and to the maximum value supported in the GUI for full series applications.

Number of sysDSP Blocks in a Row

This parameter allows the user to specify the maximum number of DSP multipliers to be use in a DSP row to

achieve optimal performance. For example, if the targeted device has 20 multipliers in a DSP row and the design

requires 22 multipliers, the user can select to use all 20 multipliers in one row and two multipliers in another row, or

fewer than 20 multipliers in each row (e.g. 8), which may yield better performance. Multipliers spread across a max-

imum of three DSP rows may be used in a single FIR instance.

This parameter is only valid on LatticeECP3 devices.

I/O Specification Tab

Figure 3-2 shows the contents of the I/O Specification tab.

Figure 3-2. I/O Specification Tab of the FIR Filter IP Core GUI

Input Data Type

This option allows the user to specify the input data type as signed or unsigned. If the type is signed, the data is

interpreted as a two’s complement number.

Input Data Width

This option allows the user to specify input data width.

Input Data Binary Point Position

This option allows the user to specify the location of the binary point in the input data. This number specifies the bit

position of the binary point from the LSB of the input data. If the number is zero, the point is right after LSB, if posi-

tive, it is to the left of LSB and if negative, it is to the right of LSB.

Parameter Settings

IPUG79_01.4, April 2014 26 FIR Filter IP Core User’s Guide

Coefficients Type

This option allows the user to specifythe coefficients type as signed or unsigned. If the type is signed, the coeffi-

cient data is interpreted as a 2’s complement number.

Coefficients Width

This option allows the user to specify the coefficients width.

Coefficients Binary Point Position

This option allows the user to specify the location of the binary point in the coefficients. This number specifies the

bit position of the binary point from the LSB of the coefficients. If the number is zero, the point is right after LSB, if

positive, it is to the left of LSB and if negative, it is to the right of LSB.

Output Width

This option allows the user to specify the output data width. The maximum full precision output width is defined by

Max Output Width = Input data width + Coefficients width +ceil(Log2(Number of taps/Interpolation factor)). The

core's output is usually a part of the full precision output equal to the Output width and extracted based on the dif-

ferent binary point position parameters.

The format for the internal full precision output is displayed as static text next to the Output width control in the GUI.

The format is displayed as W.F, where W is the full precision output width and F is the location of the binary point

from the LSB of the full precision output, counted to the left. For example, if W.F is 16.4, then the output value will

be yyyyyyyyyyyy.yyyy in binary radix (e.g. 110010010010.0101).

Output Binary Points

This option allows the user to specify the bit position of the binary point from the LSB of the actual core output. If

the number is zero, the point is right after LSB, if positive, it is to the left of LSB and if negative, it is to the right of

LSB. This number, together with the parameter Output width determines how the actual core output is extracted

from the true full precision output. The precision control parameters Overflow and Rounding are applied respec-

tively when MSBs and LSBs are discarded from the true full precision output.

Overflow

This option allows the user to specify what kind of overflow control is to be used. This parameter is available when-

ever there is a need to drop some of the MSBs from the true output. If the selection is “Saturation”, the output value

is clipped to the maximum, if positive or minimum, if negative, while discarding the MSBs. If the selection is “Wrap-

around”, the MSBs are simply discarded without making any correction.

Rounding

This option allows the user to specify the rounding method when there is a need to drop one or more LSBs from the

true output.

Parameter Settings

IPUG79_01.4, April 2014 27 FIR Filter IP Core User’s Guide

Implementation Tab

Figure 3-3 shows the contents of the I/O Specification tab.

Figure 3-3. Implementation Tab of the FIR Filter IP Core GUI

Data Memory Type

This option allows the user to specify select the type of memory that is used for storing the data. If the selection is

“EBR”, Lattice Embedded Block RAM memories are used for storing the data. If the selection is “Distributed”, look-

up-table based distributed memories are used for storing data. If “Auto” is selected, EBR memories are used for

memory sizes deeper than 128 locations and distributed memories are used for all other memories.

Coefficient Memory Type

This option allows the user to specify the type of memory that is used for storing the coefficients. If the selection is

“EBR”, EBR memories are used for storing the coefficients. If the selection is “Distributed”, distributed memories

are used for storing coefficients. If “Auto” is selected, EBR memories are used for memory sizes deeper than 128

locations and distributed memories are used for all other memories.

Input Buffer Type

This option allows the user to specify the memory type for the input buffer.

Output Buffer Type

This option allows the user to specify the memory type for the output buffer.

Optimization

This option specifies the optimization method. If “Area” is selected, the core is optimized for lower resource utiliza-

tion. If “Speed” is selected, the core is optimized for higher performance, but with slightly higher resource utilization.

Parameter Settings

IPUG79_01.4, April 2014 28 FIR Filter IP Core User’s Guide

Synchronous Reset (sr)

This option allows the user to specify if a synchronous reset port is needed in the IP. Synchronous reset signal

resets all the registers in the FIR filter IP core.

Clock Enable (ce)

This option allows the user to specify if a clock enable port is needed in the IP. Clock enable control can be used for

power saving when the core is not being used. Use of clock enable port increases the resource utilization and may

affect the performance due to the increased routing congestion.

IPUG79_01.4, April 2014 29 FIR Filter IP Core User’s Guide

This chapter provides information on how to generate the Lattice FIR Filter IP core using the ispLEVER software

IPexpress tool included in the Diamond or ispLEVER software, and how to include the core in a top-level design.

Licensing the IP Core

An IP core- and device-specific license is required to enable full, unrestricted use of the FIR Filter IP core in a com-

plete, top-level design. Instructions on how to obtain licenses for Lattice IP cores are given at:

http://www.latticesemi.com/products/intellectualproperty/aboutip/isplevercoreonlinepurchas.cfm

Users may download and generate the FIR Filter IP core and fully evaluate the core through functional simulation

and implementation (synthesis, map, place and route) without an IP license. The FIR Filter IP core also supports

Lattice’s IP hardware evaluation capability, which makes it possible to create versions of the IP core that operate in

hardware for a limited time (approximately four hours) without requiring an IP license. See for further details. How-

ever, a license is required to enable timing simulation, to open the design in the Diamond or ispLEVER EPIC tool,

and to generate bitstreams that do not include the hardware evaluation timeout limitation.

Getting Started

The FIR Filter IP core is available for download from Lattice's IP server using the IPexpress or the Clarity Designer

tool. The IP files are automatically installed using ispUPDATE technology in any customer-specified directory. After

the IP core has been installed, the IP core will be available in the IPexpress GUI or the Clarity Designer tool.

The IPexpress tool GUI dialog box for the FIR Filter IP core is shown in Figure 4-1. To generate a specific IP core

configuration the user specifies:

•Project Path – Path to the directory where the generated IP files will be located.

•File Name – “username” designation given to the generated IP core and corresponding folders and files.

•(Diamond) Module Output – Verilog or VHDL.

•Device Family – Device family to which IP is to be targeted (e.g. LatticeXP2, LatticeECP3, etc.). Only families

that support the particular IP core are listed.

•Part Name – Specific targeted part within the selected device family.

Chapter 4:

IP Core Generation and Evaluation

IPUG79_01.4, April 2014 30 FIR Filter IP Core User’s Guide

Figure 4-1. IPexpress Dialog Box

Note that if the IPexpress tool is called from within an existing project, Project Path, Module Output, Device Family

and Part Name default to the specified project parameters. Refer to the IPexpress tool online help for further infor-

mation.

To create a custom configuration, the user clicks the Customize button in the IPexpress tool dialog box to display

the FIR Filter IP core Configuration GUI, as shown in Figure 4-2. From this dialog box, the user can select the IP

parameter options specific to their application. Refer to “Parameter Settings” on page 21 for more information on

the FIR Filer IP core parameter settings.

IP Core Generation and Evaluation

IPUG79_01.4, April 2014 31 FIR Filter IP Core User’s Guide

Figure 4-2. Configuration Dialog Box

The Clarity Designer tool GUI dialog box for the FIR Filter IP core is shown in Figure 4-3.

•Create new Clarity design - Choose to create a new Clarity Design project directory in which the FIR IP core

will be generated.

•Design Location - Clarity Design project directory Path.

•Design Name - Clarity Design project name.

•HDL Output - Hardware Description Language Output Format (Verilog or VHDL).

•Open Clarity design - Open an existing Clarity Design project.

•Design File - Name of existing Clarity Design project file with .sbx extension.

Figure 4-3. Clarity Designer Tool Dialog Box

IP Core Generation and Evaluation

IPUG79_01.4, April 2014 32 FIR Filter IP Core User’s Guide

The Clarity Designer Catalog tab is shown in Figure 4-4. To generate FIR IP core configuration by double clicking

the IP name in the Catalog tab.

Figure 4-4. Clarity Designer Catalog Tab

In the Fir Filter dialog box shown Figure 4-5, specify the following:

• Instance Name - The instance module name of FIR IP core.

Figure 4-5. IP Generation Dialog Box

Note that if the Clarity Designer tool is called from within an existing project, Design Location, Device Family and

Part Name default to the specified project parameters. Refer to the Clarity Designer tool online help for further

information.

To create a custom configuration, click the Customize button in the Clarity Designer tool dialog box to display the

FIR IP core Configuration GUI, as shown in Figure 4-6. From this dialog box, the user can select the IP parameter

options specific to their application. Refer to ““Parameter Settings” on page 21 for more information on the FIR

parameter settings.

IP Core Generation and Evaluation

IPUG79_01.4, April 2014 33 FIR Filter IP Core User’s Guide

Figure 4-6. IP Configuration GUI

IP Core Generation and Evaluation

IPUG79_01.4, April 2014 34 FIR Filter IP Core User’s Guide

IPexpress-Created Files and Top Level Directory Structure

When the user clicks the Generate button, the IP core and supporting files are generated in the specified “Project

Path” directory. The directory structure of the generated files is shown in Figure 4-7.

Figure 4-7. FIR Filter IP Core Generated Directory Structure

The design flow for IP created with the IPexpress tool uses a post-synthesized module (NGO) for synthesis and a

protected model for simulation. The post-synthesized module is customized and created during the IPexpress tool

generation.

Table 4-1 provides a list of key files created by the IPexpress tool. The names of most of the created files are cus-

tomized to the user’s module name specified in the IPexpress tool. The files shown in Table 4-1 are all of the files

necessary to implement and verify the FIR Filter IP core in a top-level design.

Table 4-1. File List

File Description

<username>_inst.v This file provides an instance template for the IP.

<username>.v This file provides a wrapper for the FIR core for simulation.

<username>_beh.v This file provides a behavioral simulation model for the FIR core.

<username>_bb.v This file provides the synthesis black box for the user’s synthesis.

<username>.ngo The ngo files provide the synthesized IP core.

<username>.lpc This file contains the IPexpress tool options used to recreate or modify the core in the IPex-

press tool.

<username>.ipx IPexpress package file (Diamond only). This is a container that holds references to all of the

elements of the generated IP core required to support simulation, synthesis and implementa-

tion. The IP core may be included in a user's design by importing this file to the associated Dia-

mond project.

IP Core Generation and Evaluation

IPUG79_01.4, April 2014 35 FIR Filter IP Core User’s Guide

The following additional files providing IP core generation status information are also generated in the “Project

Path” directory:

•<username>_generate.tcl – A TCL scripts which can regenerate the IP from command line.

•<username>_generate.log – Synthesis and map log file.

•<username>_gen.log – IPexpress IP generation log file.

Instantiating the Core

The generated FIR Filter IP core package includes black-box (<username>_bb.v) and instance (<user-

name>_inst.v) templates that can be used to instantiate the core in a top-level design. An example RTL top-level

reference source file that can be used as an instantiation template for the IP core is provided in 

\<project_dir>\fir_eval\<username>\src\rtl\top. You may also use this top-level reference as the

starting template for the top-level for their complete design. By regenerating an IP core with the Clarity Designer

tool, you can modify any of the options specific to an existing IP instance. By recreating an IP core with Clarity

Designer tool, you can create (and modify if needed) a new IP instance with an existing LPC/IPX configuration file.

Running Functional Simulation

Simulation support for the FIR Filter IP core is provided for Aldec Active-HDL (Verilog and VHDL) simulator, Mentor

Graphics ModelSim simulator. The functional simulation includes a configuration-specific behavioral model of the

FIR Filter IP core. The test bench sources stimulus to the core, and monitors output from the core. The generated

IP core package includes the configuration-specific behavior model (<username>_beh.v) for functional simulation

in the “Project Path” root directory. The simulation scripts supporting ModelSim evaluation simulation is provided in

\<project_dir>\fir_eval\<username>\sim\modelsim\scripts. The simulation script supporting

Aldec evaluation simulation is provided in \<project_dir>\fir_eval\<username>\sim\aldec\scripts.

Both Modelsim and Aldec simulation is supported via test bench files provided in

\<project_dir>\fir_eval\testbench. Models required for simulation are provided in the corresponding

\models folder. Users may run the Aldec evaluation simulation by doing the following:

1. Open Active-HDL.

2. Under the Tools tab, select Execute Macro.

3. Browse to folder \<project_dir>\fir_eval\<username>\sim\aldec\scripts and execute one of the

"do" scripts shown.

Users may run the Modelsim evaluation simulation by doing the following:

1. Open ModelSim.

2. Under the File tab, select Change Directory and choose the folder 

<project_dir>\fir_eval\<username>\sim\modelsim\scripts.

3. Under the Tools tab, select Execute Macro and execute the ModelSim “do” script shown.

Note: When the simulation is complete, a pop-up window will appear asking “Are you sure you want to finish?”

Choose No to analyze the results. Choosing Yes closes ModelSim.

pmi_*.ngo One or more files implementing synthesized memory modules used in the IP core.

*.rom This file provides filter coefficient memory initialization data.

Table 4-1. File List (Continued)

File Description

IP Core Generation and Evaluation

IPUG79_01.4, April 2014 36 FIR Filter IP Core User’s Guide

Synthesizing and Implementing the Core in a Top-Level Design

The FIR Filter IP core itself is synthesized and provided in NGO format when the core is generated through IPex-

press. You may combine the core in your own top-level design by instantiating the core in your top-level file as

described in “Instantiating the Core” on page 35 and then synthesizing the entire design with either Synplify or Pre-

cision RTL Synthesis.

The following text describes the evaluation implementation flow for Windows platforms. The flow for Linux and

UNIX platforms is described in the Readme file included with the IP core.

The top-level file <userame>_top.v is provided in 

\<project_dir>\fir_eval\<username>\src\rtl\top. Push-button implementation of the reference

design is supported via the project file <username>.ldf located in \<project_dir>\fir_eval\<user-

name>\impl\synplify.

To use this project file in Diamond:

1. Choose File > Open > Project.

2. Browse to 

\<project_dir>\fir_eval\<username>\impl\synplify in the Open Project dialog box.

3. Select and open <username>_.ldf. At this point, all of the files needed to support top-level synthesis and imple-

mentation will be imported to the project.

4. Select the Process tab in the left-hand GUI window.

5. Implement the complete design via the standard Diamond GUI flow.

Hardware Evaluation

The FIR Filter IP core supports Lattice’s IP hardware evaluation capability, which makes it possible to create ver-

sions of the IP core that operate in hardware for a limited period of time (approximately four hours) without requiring

the purchase of an IP license. It may also be used to evaluate the core in hardware in user-defined designs. The

hardware evaluation capability may be enabled/disabled in the Properties menu of the Build Database setup in Dia-

mond Project Navigator.

Enabling Hardware Evaluation in Diamond:

Choose Project > Active Strategy > Translate Design Settings. The hardware evaluation capability may be

enabled/disabled in the Strategy dialog box. It is enabled by default.

Updating/Regenerating the IP Core

By regenerating an IP core with the IPexpress tool, you can modify any of its settings including: device type, design

entry method, and any of the options specific to the IP core. Regenerating can be done to modify an existing IP

core or to create a new but similar one.

Regenerating an IP Core in Diamond

To regenerate an IP core in Diamond:

1. In IPexpress, click the Regenerate button.

2. In the Regenerate view of IPexpress, choose the IPX source file of the module or IP you wish to regenerate.

3. IPexpress shows the current settings for the module or IP in the Source box. Make your new settings in the Tar-

get box.

IP Core Generation and Evaluation

IPUG79_01.4, April 2014 37 FIR Filter IP Core User’s Guide

4. If you want to generate a new set of files in a new location, set the new location in the IPX Target File box. The

base of the file name will be the base of all the new file names. The IPX Target File must end with an .ipx exten-

sion.

5. Click Regenerate. The module’s dialog box opens showing the current option settings.

6. In the module dialog box, choose the desired options. 



For more information about the options, click Help. Also, check the About tab in IPexpress for links to technical

notes and user guides. IP may come with additional information. 



As the options change, the schematic diagram of the module changes to show the I/O and the device resources

the module needs.

7. To import the module into your project, if it’s not already there, select Import IPX to Diamond Project (not

available in stand-alone mode).

8. Click Generate.

9. Check the Generate Log tab to check for warnings and error messages.

10.Click Close.

The IPexpress package file (.ipx) supported by Diamond holds references to all of the elements of the generated IP

core required to support simulation, synthesis and implementation. The IP core may be included in a user's design

by importing the .ipx file to the associated Diamond project. To change the option settings of a module or IP that is

already in a design project, double-click the module’s .ipx file in the File List view. This opens IPexpress and the

module’s dialog box showing the current option settings. Then go to step 6 above.

Regenerating an IP Core in Clarity Designer Tool

To regenerate an IP core in Clarity Designer:

1. In the Clarity Designer Builder tab, right-click on the existing IP instance and choose Config.

2. In the module dialog box, choose the desired options. 



For more information about the options, click Help. You may also click the About tab in the Clarity Designer win-

dow for links to technical notes and user guides. The IP may come with additional information. 



As the options change, the schematic diagram of the module changes to show the I/O and the device resources

the module needs.

3. Click Configure.

Recreating an IP Core in Clarity Designer Tool

To recreate an IP core in Clarity Designer:

1. In Clarity Designer click the Catalog tab.

2. Click the Import IP tab (at the bottom of the view).

3. Click Browse.

4. In the Open IPX File dialog box, browse to the .ipx or .lpc file of the module. Use the .ipx if it is available.

5. Click Open.

IP Core Generation and Evaluation

IPUG79_01.4, April 2014 38 FIR Filter IP Core User’s Guide

6. Type in a name for Target Instance. Note that this instance name should not be the same as any of the existing

IP instances in the current Clarity Designer project.

7. Click Import. The module's dialog box opens.

8. In the dialog box, choose desired options. 



For more information about the options, click Help. You may also check the About tab in the Clarity Designer

window for links to technical notes and user guides. The IP may come with additional information. 



As the options change, the schematic diagram of the module changes to show the ports and the device

resources the module needs.

9. Click Configure.

IPUG79_01.4, April 2014 39 FIR Filter IP Core User’s Guide

This chapter contains information about Lattice Technical Support, additional references, and document revision

history.

Lattice Technical Support

There are a number of ways to receive technical support.

E-mail Support

techsupport@latticesemi.com

Local Support

Contact your nearest Lattice sales office.

Internet

www.latticesemi.com

LatticeXP2

•DS1009, Lattice XP2 Data Sheet

LatticeECP3

•HB1009, LatticeECP3 Family Handbook

ECP5

•HB1012, ECP5 Family Handbook

Revision History

Initial release.

Added support for LatticeECP3 FPGA family.

Updated appendices for ispLEVER 7.2 SP1.

Added support for Diamond software throughout.

Divided document into chapters. Added table of contents.

Added Quick Facts tables in Chapter 1, “Introduction.”

Added new content in Chapter 4, “IP Core Generation.”

May 2011 Added support for multipliers in multiple DSP rows.

Changed interface timing for certain configurations in

LatticeECP3 devices.

Added support for ECP5 FPGA family.

Added high speed mode.

Updated document with new corporate logo.

Updated Technical Support information.

Date

Document

Version

Version Change Summary

September 2008 01.0 3.1

April 2009 01.1 4.0

June 2010 01.2 4.2

01.3 5.0

April 2014 01.4 6.0asr

Chapter 5:

Support Resources

IPUG79_01.4, April 2014 40 FIR Filter IP Core User’s Guide

This appendix gives resource utilization information for Lattice FPGAs using the FIR IP core. The IP configurations

shown in this chapter were generated using the IPexpress software tool and Clarity Designer tool. IPexpress and

Clarity Designer are the Lattice IP configuration utility, and are included as a standard feature of the Diamond

design tool. Details regarding the usage of IPexpress and Clarity Designer can be found in the IPexpress, Clarity

Designer and Diamond help systems. For more information on the Diamond design tool, visit the Lattice web site

at: www.latticesemi.com/software.

LatticeECP3 Devices

Table A-1. Performance and Resource Utilization1

Ordering Part Number

The Ordering Part Number (OPN) for the FIR Filter IP Core targeting LatticeECP3 devices is FIR-COMP-E3-U4.

LatticeXP2 Devices

Table A-2. Performance and Resource Utilization1

Ordering Part Number

The Ordering Part Number (OPN) for the FIR Filter IP Core targeting LatticeXP2 devices is FIR-COMP-X2-U4.

IPexpress

User-Configurable Mode Slices LUTs Registers DSP Slices

sysMEM

EBRs fMAX (MHz)

4 channels, 64 taps, multiplier multiplexing 64 97 150 174 2 2 302

1 channel, 32 taps, multiplier multiplexing 1 50 48 98 16 0 258

1 channel, 32 taps, multiplier multiplexing 4 228 132 432 5 8 213

1. Performance and utilization characteristics are generated targeting an LFE3-70E-8FN672CES device using Lattice Diamond 3.0 and Syn-

plify Pro D-2013.09L beta software. Performance may vary when using this IP core in a different density, speed or grade within the

LatticeECP3 family or in a different software version.

IPexpress

User-Configurable Mode Slices LUTs Registers

18x18

Multipliers

sysMEM

EBRs fMAX (MHz)

4 channels, 64 taps, multiplier multiplexing 64 57 96 114 1 1 314

1 channel, 32 taps, multiplier multiplexing 1 175 311 322 32 0 277

1 channel, 32 taps, multiplier multiplexing 4 130 166 256 8 8 203

1. Performance and utilization characteristics are generated targeting an LFXP2-40E-7F672C device using Lattice Diamond 3.0 and Synplify

Pro D-2013.09L beta software. Performance may vary when using this IP core in a different density, speed or grade within the LatticeXP2

family or in a different software version.

Appendix A:

Resource Utilization

IPUG79_01.4, April 2014 41 FIR Filter IP Core User’s Guide

ECP5 Devices

Table A-3. Performance and Resource Utilization

Table A-4. Performance and Resource Utilization1, 2,

Ordering Part Number

The Ordering Part Number (OPN) for all configurations of the FIR Filter IP Core targeting ECP5 devices is FIR-

COMP-E5-U.

Clarity Designer

User-Configurable Mode

(Low Speed) Diamond Slices LUTs Registers DSP Slices

sysMEM

EBRs fMAX (MHz)

4 channels, 64 taps,

multiplier multiplexing 64 Diamond 125 143 174 2 2 295

1 channel, 32 taps,

multiplier multiplexing 1 Diamond 55 47 98 16 0 223

1 channel, 32 taps,

multiplier multiplexing 4 Diamond 242 133 432 5 8 231

1. Performance and utilization characteristics are generated targeting LFE4UM-85F-8BG756I using Lattice Diamond 3.2 and Synplify Pro F-

2013.09L beta software. When using this IP core in a different density, speed, or grade within the ECP5 device family or in a different soft-

ware version, performance may vary.

Clarity Designer

User-Configurable Mode

(High Speed) Diamond Slices LUTs Registers DSP Slices

sysMEM

EBRs fMAX (MHz)

1 channel, 64 taps,

multiplier multiplexing 4 Diamond 760 737 1018 10 24 182

1 channel, 24 taps,

multiplier multiplexing 4 Diamond 428 372 643 5 9 194

1 channel, 48 taps,

multiplier multiplexing 4 Diamond 660 633 929 8 18 198

1. Performance and utilization characteristics are generated targeting LFE5UM-85F-8MG756I using Lattice Diamond 3.2 and Synplify Pro F-

2013.09L beta software. When using this IP core in a different density, speed, or grade within the ECP5 device family or in a different soft-

ware version, performance may vary.

2. For each channel in the high-speed mode, it actually has I/Q data coming in TDM mode, so it is able to process data in 2X throughput com-

pared to low-speed mode.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Lattice:

FIR-COMP-EP-UT3 FIR-COMP-P2-UT3 FIR-COMP-PM-UT3 FIR-COMP-X2-U4 FIR-COMP-X2-UT4 FIR-COMP-

P2-U3 FIR-COMP-EP-U3 FIR-COMP-PM-U3 FIR-COMP-E2-U4 FIR-COMP-E2-UT4 FIR-COMP-E3-U4 FIR-COMP-

E3-UT4 FIR-COMP-P2-U4 FIR-COMP-P2-UT4 FIR-COMP-PM-U4 FIR-COMP-PM-UT4