LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 Data Sheet 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Inc, Proprietary and Confidential August 2003 Preliminary Information MC2042-4 MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 TABLE OF CONTENTS 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 2 of 13 Preliminary Information Features ...........................................................................................................................................................3 Applications ......................................................................................................................................................3 Connections ......................................................................................................................................................3 General Description ..........................................................................................................................................3 Table 1 Ordering Information ............................................................................................................................3 Top Level Diagram ...........................................................................................................................................3 Table 2 Pin Descriptions ...................................................................................................................................4 Table 3 Absolute Maximum Ratings .................................................................................................................5 Table 4 DC Electrical Characteristics ...............................................................................................................5 Table 5 AC Electrical Characteristics ...............................................................................................................5 Typical Applications Circuit ...............................................................................................................................6 Functional Description ......................................................................................................................................6 Current Switch ..................................................................................................................................................6 LED Drive and Temperature Compensation ....................................................................................................6 Transmit Enable/Disable ..................................................................................................................................7 Pre-emphasis or `Peaking' ................................................................................................................................7 LED clamping, Laser driving .............................................................................................................................7 LED drive Pulse Width Adjust (PWA) ...............................................................................................................8 Eye Diagram......................................................................................................................................................8 Evaluation Board ...............................................................................................................................................9 Bare Die ..........................................................................................................................................................10 Table 6 Bare Die Pad Coordinates ...................................................................................................................10 TSSOP20 Package Information .......................................................................................................................11 QSOP16 Package Information .........................................................................................................................12 Table 7 TSSOP20 Dimensions .........................................................................................................................12 Table 8 QSOP16 Dimensions ..........................................................................................................................12 Disclaimer .........................................................................................................................................................13 Contact Information ...........................................................................................................................................14 MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 GENERAL DESCRIPTION Data rates to >300 Mbps, depending on LED Single chip solution, available as die or in TSSOP20 or QSOP16 fabricated in deep sub-micron CMOS for lowest cost & power consumption and long term reliability Programmable output current from 5 mA to 100 mA RC programmable pre-emphasis or `peaking' circuit giving drive current rise and fall times <500 ps Resistor programmable compensation for temperature dependence of LED output power PECL input with optional Pulse Width Adjust Single-ended CMOS input compatible at low speeds VREF voltage generator and output pin Supports most LED types (e.g. 660 to 1300 nm) Single +5 V to +3.3 V operation The MC2042-4 is a CMOS IC designed for high-speed LED drive in low-cost optical fiber based transmission systems. Depending on the LED used, data rates to >300Mbps can be achieved. APPLICATIONS FDDI, fiber Channel Fast Ethernet, IEEE1394 OC3/STM1 To minimize the effects of temperature on LED output power, LED drive temperature compensation can be set by resistor over a 500 - 10,000 ppm/C range. Differential positive-ECL (PECL) data on the input pins can be shaped, if desired, by the differential voltage on the Pulse Width Adjust (PWA) pins. This adjustment is continuous over a 500 ps range. In addition, the VREF output pin allows single-ended input to the MC2042 and provides compatibility with industry-standard FO modules. TABLE 1 CONNECTIONS Fig.1 The LED drive current is set by a resistor. To improve LED `on' time, a pre-emphasis circuit is included, which may be set via a simple RC network. TSSOP20 TOP VIEWS NC PWAPWA- 1 20 NC 2 19 GND 3 18 GND DIN 4 17 IOUT 16 IOUT 15 IOUT PEAK DIN 5 VREF 6 RESET2 7 14 RTSET 8 13 VDD2 VDD1 9 12 VDD2 NC 10 11 NC MC2042-4 Datecode ORDERING INFORMATION Part Pin-Package MC2042-4DIEWP Waffle pack MC2042-4WAFER Expanded Whole Wafer on a ring MC2042-4Q16 QSOP16 MC2042-4T20 TSSOP20 TOP LEVEL DIAGRAM Fig. 2 6.5 x 4.4mm TSSOP Package V DD1 QSOP16 PWA- 1 16 GND PWA+ 2 15 GND DIN 3 14 IOUT 13 IOUT DIN 4 VREF 5 12 IOUT RTSET2 6 11 PEAK RTSET 7 10 VDD2 VDD1 8 9 VDD2 MC2042-4 Datecode D IN D IN V DD2 IO U T IO U T PEAK Input D ata P u lse S haping C urrent S w itch and P eaking C ontrol V R E F G en erator P rogram m able C urrent S ink PW A PWA V REF GND GND R T SET R T S E T2 4.3 x 3.9mm QSOP Package 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 3 of 14 Preliminary Information FEATURES MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 TABLE 2 PIN DESCRIPTIONS QSOP16 Pin Die Pin Name 1 - - NC 2 1 13 PWA Inverse pulse width adjust input 3 2 14 PWA Differential pulse width adjust input. Allows continuous adjustment of input data pulse width 4 3 15 DIN Differential data input 5 4 16 DIN Inverse differential data input 6 5 1 VREF 7 6 2 RTSET2 Temperature compensation adjustment pin. Allows temperature dependence of LED light output to be reduced or removed 8 7 3 RTSET Sets nominal LED drive current 9 8 4 VDD1 Power pin, connect to most positive supply 10 - - NC Not connected 11 - - NC Not connected 12 9 5 VDD2 LED shorting pin, connect to most positive supply. Speeds LED switch off 13 10 6 VDD2 LED shorting pin, connect to most positive supply. Speeds LED switch off 14 11 7 PEAK Connection for pre-emphasis or peaking circuit 15 12 8 IOUT Driver output. Connect LED between this pin and VDD 16 13 9 IOUT Driver output. Connect LED between this pin and VDD 17 14 10 IOUT Logical inverse of pin 8. Connect resistor of approximately the same value as LED (at the programmed drive current level) between this pin and VDD 18 15 11 GND Ground pin. Connect to the most negative supply 19 16 12 GND Ground pin. Connect to the most negative supply 20 - - NC 02042-DSH-001-C 8/03 Description Not connected, leave open Reference output. Can be used with single-ended data input Not connected, leave open Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 4 of 14 Preliminary Information TSSOP20 Pin MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 TABLE 3 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Total power dissipation (TSSOP20) VCC Power supply (VCC-GND) Units 255 mW 7 V 150 C TJ Junction temperature TA Operating ambient -40 to +85 C Storage temperature -65 to +50 C TSTG These are the absolute maximum ratings at or beyond which the IC can be expected to fail or be damaged. Reliable operation at these extremes for any length of time is not implied. TABLE 4 DC ELECTRICAL CHARACTERISTICS Symbol Parameter Min Typ Max Units 3.0 - 5.5 V VCC Supply Voltage Din Allowable voltage at data inputs Gnd - 0.3 - VCC+0.3 VREF Voltage reference VCC-1.6 VCC-1.4 VCC-1.03 ILED' ON LED drive current 5 - 120 mA ILED' OFF LED off current - - 50 A ICOMP LED drive current temperature compensation range 0.05 - 1 %/C V_LED_H Minimum allowable voltage at IOUT VDD-2.0 - - V TABLE 5 AC ELECTRICAL CHARACTERISTICS Symbol Vin(Diff) Parameter Min Typ Max Units Differential Input Voltage, 2*(DinH - DinL) 300mV Common Mode Input Voltage VCC/2 - 2*Vcc V - (Vcc-(Vin[Diff])/4) V fC Maximum data rate 300 - - Mbps TPWA Input data pulse width adjust range -500 - 500 ps LED tr LED drive rise time - 0.7 1 ns LED tf LED drive fall time - 0.7 1 ns IPEAK Peaking current (as % of LED drive current) 0 - 50 % PEAK tr Peaking current rise time - - 1 ns PEAK tf Peaking current fall time - - 1 ns PEAK td Peaking current decay time - C1x(R4+5) - S IDD Supply current - ILED+10 ILED+20 mA 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 5 of 14 Preliminary Information PTOT Rating MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 TYPICAL APPLICATIONS CIRCUIT Fig. 3 VCC Preliminary Information LED Dummy LED Load Optional Peaking R4 C1 VDD1 DIN DIN VDD2 IOUT IOUT PEAK Input Data Pulse Shaping Current Switch and Peaking Control VREF Generator Programmable Current Sink PWA PWA VREF GND GND2 RTSET R2 RTSET2 R1 FUNCTIONAL DESCRIPTION Current Switch Differential Positive-ECL (PECL) data on the data input pins controls the LED current switch. The LED current flows either through the LED or via the dummy load so that VDD noise is minimized. To reduce LED `turn-off' time, the LED is momentarily short-circuited, via VDD2, before the current is switched to the dummy load. LED Drive and Temperature Compensation The two resistors R1 and R2 set the LED drive current and temperature compensation. The simplified application diagram (Fig. 3) shows R1 connected between RTSET and GND, and R2 between RTSET and the RTSET2 pin. The current flowing out of the RTSET pin determines the LED drive current. The temperature independent component of the LED drive current is set primarily by R1. The temperature 02042-DSH-001-C 8/03 dependent component is set primarily by R2. However, R1 and R2 are not independent. The RTSET2 pin connects to an internal diode in the IC, which exhibits standard diode behaviour with temperature. As temperature rises, the voltage on the diode drops, the current flowing through R2 increases and the LED drive current increases. The LED `on' current is controlled to 5%. If the operating temperature of the MC2042 is not representative of the LED temperature, an external diode may be used in place of the temperature compensating diode internal to the MC2042. Figure 4 illustrates a circuit using an external diode for temperature compensation. A Microsoft Excel file is available from Mindspeed which will calculate appropriate values for RTset resistors R1 and R2 given your LED current, forward voltage, and LED temperature coefficient. The file may be obtained from a Mindspeed Field Applications Engineer and is named 'MC2042-4 resistor selection.xls'. Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 6 of 14 MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 FUNCTIONAL DESCRIPTION Pre-Emphasis Or `Peaking' RTSET RTSET2 (unused) R2 Two external components (R4, C1) are required as shown in Fig. 3 to implement peaking. External Diode for Temp. Comp. R1 Transmit Enable/Disable There is no dedicated pin on the MC2042 to disable the LED drive current. However, the LED drive current can be disabled by disabling the current out of pin RTSET. The LED current is approximately 100x the current out of pin RTSET, so if the current out of this pin is 0, the LED drive current is 0. However, if peaking is used the peaking current will not be disabled. Figure 5 illustrates how the current out of RTSET can be disabled by adding a MOSFET (Q1) at the RTSET node of the R1/R2 temperature compensation network. The voltage on the gate of Q1 then controls transmit enable/ disable. When selecting Q1, a MOSFET should be chosen with an Rds(on) which is negligible compared to R1 and R2. Fig. 5 RTSET RTSET2 Transmit Enable R2 Q1 R1 When the LED is turned on, the voltage on PEAK is pulled LOW very rapidly. This voltage transient is coupled through R4 and C1 and exerts a transient current on the LED. When the LED is turned off, the voltage on PEAK is pulled HIGH rapidly. This voltage transient is coupled through R4 and C1 and exerts a transient current in the opposite direction on the LED. The transient current amplitude and RC decay are given approximately by: Peak current (Amps): 4/(R4 + 5) Decay (seconds): C1 x (R4 + 5) The above approximations assume an ideal LED model with 0 Ohms resistance. Real LEDs will slightly alter the peaking effect. Typical values for R4 and C1 are: R4 = 50 C1 = 20 pF LED Clamping, Laser Driving Since most LEDs exhibit a longer `turn off' time than `turn on' time, a clamping function is included on the MC2042 in order to reduce the `turn off' time. Clamping is enabled via the two VDD2 connections. The disadvantage of clamping is that the LED's internal capacitance has to be fully charged again before the LED starts to emit light. This delayed `turn on' effect becomes noticeable when the nominal LED drive current is low. Use of the peaking circuit helps solve this problem. Thus, the combination of peaking and clamping results in very fast `turn on' and `turn off' times for the LED. When driving lasers, it will often be helpful to disable this clamping. This can be achieved by leaving the VDD2 connections floating. VDD1 must still be connected. 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 7 of 14 Preliminary Information Fig. 4 To improve LED `turn on' time an optional pre-emphasis function is included on the MC2042-4. If this is not required, then the PEAK pin should be left floating. MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 FUNCTIONAL DESCRIPTION LED Drive Pulse Width Adjust (PWA) Delta PW (ps) = K x VPWA Eye Diagram The eye diagram below is typical of the electrical output of the MC2042-4. The crossover point can be moved up and down using the PWA pin. The overshoot can be increased by using the PEAK pin. Where: K = 500 100 and VPWA = (VPWA+) - (VPWA-) The maximum range for VPWA is 1V. The input impedance is 3.6 k. VPWA+ and VPWA- will settle at a nominal voltage equal to (0.6 * VDD) if left floating. It is recommended that adjustment be implemented by pull down resistors on PWA+ or PWA-. However, it is common for one or other pin to be tied to ground as a zero-cost, `gross' adjustment. Fig. 6 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 8 of 14 Preliminary Information The input pulse width can be adjusted prior to application to the LED switch. The differential voltage on the PWA (Pulse Width Adjust) pins shapes the input pulse linearly over a nominal -500 to +500 ps range, according to the formula: If pulse width adjustment is not required PWA+ and PWAshould be tied to ground. A B C D 1 1 0V HD1 3.3V 1 2 3 POWER SK5 DATA_INB SK4 DATA_IN DATA INPUTS SK6 1 DATA_CMOS 2 2 02042-DSH-001-C 8/03 2 1 + C10 10UF EXCCL3216U L2 R5 50R C7 100NF VCC1 R14 N/C R13 N/C VCC1 C9 100NF VCC2 C11 10NF R6 50R 100NF R8 N/C EXCCL3216U L1 C5 C6 100NF N/C R9 C12 10NF VCC1 R16 N/C R15 N/C R17 50K R10 1K R19 50K R7 10K R18 50K 2 3 C1 10NF VCC1 VBB 10 9 8 7 6 5 4 3 2 1 IC1 N/C N/C VDD2 VDD2 PEAK IOUT IOUT IOUTB GND GND 11 12 13 14 15 16 17 18 19 20 0R R1 R2 R3 R4 C2 10NF N/C N/C 22R C3 10NF 3 TITLE VCC2 18PF C4 C8 100NF VCC2 SK3 SK2 SK1 SHEET OF 1 1 4 REV 1 DOC_NO MC2042 CAN_GND CATHODE ANODE LED INTERFACE Inputs ----------SK4 & SK5 are provided for the connection of differential PECL input signals. Alternatively a CMOS input may be connected to SK6.If using SK6, remove R6, C5 & C6 and fit R8 & R9 with 1K resistors. The drive current and temperature compensation is determined by two potentiometers , R19 & R7 respectively .LED turn-on time can be improved by proper selection of R2, R3 & C4. Refer to Microcosm documentation for selection of these values. MC2042-4 EVALUATION BOARD UNIVERSITY GATE PARK ROW BRISTOL. 4 LED drive current & temp compensation - R19 & R7 MICROCOSM COMMUNICATIONS LTD MICROCOSM MC2042-4 N/C VDD1 RTSET RTSET2 VBB DIN- DIN+ PWA+ PWA- N/C These pots can be altered to give a total of +/- 500 pS Pulse width adjustment. No adjustment occurs if PWA + & PWA- are tied to gnd. Maximum adjustment in either direction is obtained by connecting PWA+ to VCC and PWA- to gnd , or viceversa. Controls -------------Pulse width adjust - R17/R18 General ------------The board allows the user full flexibility for determining the resistor valuesrequired for the pulse width adjust, LED current and LED temperature compensation functions. This board is provided for evaluation of the MC2042-4 SET NOMINAL LED DRIVE CURRENT SET LED TEMP COMP R12 N/C R11 N/C LED PULSE WIDTH ADJUST VCC1 2 A B C D Fig. 7 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Preliminary Information 1 MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 Evaluation Board An electrical evaluation board is available for the MC2042-4. Its schematic is shown below. Page 9 of 14 MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 BARE DIE VREF DIN DIN 2 1 16 15 VDD1 4 13 PWA VDD2 5 12 GND VDD2 6 11 GND Die size: 1.0 x 1.0 mm Pad openings: 95 um square 7 8 9 10 IOUT PWA IOUT 14 IOUT 3 PEAK RTSET TABLE 6 Pad Preliminary Information RTSET2 Fig. 8 BARE DIE PAD COORDINATES Description X Y Pad Description X Y 1 VREF -73 394.5 9 IOUT 73 -394.5 2 RTSET2 -219 394.5 10 IOUT 219 -394.5 3 RTSET -397 214.7 11 GND 397 -223.3 4 VDD1 -397 68.7 12 GND 397 -77.3 5 VDD2 -397 -77.3 13 PWA 397 68.7 6 VDD2 -397 -223.3 14 PWA 397 214.7 7 PEAK -219 -394.5 15 DIN 219 394.5 8 IOUT -73 -394.5 16 DIN 73 394.5 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 10 of 14 MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 TSSOP20 PACKAGE INFORMATION Fig. 9 Preliminary Information Note: Package dimensions on page 12. 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 11 of 14 MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel, OC3/STM-1, IEEE1394 QSOP16 PACKAGE INFORMATION Fig. 10 Preliminary Information TABLE 7 TSSOP20 DIMENSIONS TABLE 8 QSOP16 DIMENSIONS Dims. Tols/leads TSSOP20L Dims. Tols/N QSOP16 A MAX 1.20 A MAX. 1.60 0.5MIN/.10MAX. A1 .05 0.1 A1 A2 NOM .90 A2 .10 1.40 D .05 6.50 D .10 4.9 E .10 6.40 E .20 6.00 E1 .10 4.40 E1 .10 3.90 L +.15/-.10 .60 L .05 0.6 L1 REF. 1.00 ccc MAX. 0.10 Zp REF. .325 ddd MAX. 0.10 e BASIC .65 e BASIC 0.65 b .05 .22 b .05 0.25 c .05 .2 Min. .24 Max. c .13MIN/.20MAX e 4 4 aaa MAX. .10 R .05 0.20 bbb MAX. .10 R1 Min. 0.20 ccc MAX .05 ddd MAX. .20 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 12 of 14 MC2042-4 LED/Laser Driver for FDDI, Fast Ethernet, Fibre Channel OC3/STM-1 DISCLAIMER Information in this document is provided in connection with Mindspeed TechnologiesTM ("MindspeedTM") products. These materials are provided by Mindspeed as a service to its customers and may be used for informational purposes only. Except as provided in Mindspeed's Terms and Conditions of Sale for such products or in any separate agreement related to this document, Mindspeed assumes no liability whatsoever. Mindspeed assumes no responsibility for errors or omissions in these materials. Mindspeed may make changes to specifications and product descriptions at any time, without notice. Mindspeed makes no commitment to update the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to its specifications and product descriptions. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF MINDSPEED PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. MINDSPEED FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. MINDSPEED SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE OF THESE MATERIALS. Mindspeed products are not intended for use in medical, lifesaving or life sustaining applications. Mindspeed customers using or selling Mindspeed products for use in such applications do so at their own risk and agree to fully indemnify Mindspeed for any damages resulting from such improper use or sale. 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 13 of 14 Preliminary Information (c) 2003, Mindspeed TechnologiesTM, Inc. All rights reserved. Contact Information Headquarters Newport Beach Mindspeed Technologies 4000 MacArthur Boulevard, East Tower Newport Beach, CA 92660 Phone: (949) 579-3000 Fax: (949) 579-3020 www.mindspeed.com 02042-DSH-001-C 8/03 Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice. MindspeedTM Technologies, Proprietary and Confidential Page 14 of 14