MMA8491Q 3-Axis Multifunction Digital Accelerometer Rev. 2.1 -- 26 April 2016 1 Data sheet: Technical data COMPANY PUBLIC General description The MMA8491Q is a low voltage, 3-axis low-g accelerometer housed in a 3 mm x 3 mm QFN package. The device can accommodate two accelerometer configurations, acting 2 as either a 45 tilt sensor or a digital output accelerometer with I C bus. * As a 45 tilt sensor, the MMA8491Q device offers extreme ease of implementation by using a single line output per axis. * As a digital output accelerometer, the 14-bit 8 g accelerometer data can be read from the device with a 1 mg/LSB sensitivity. The extreme low power capabilities of the MMA8491Q will reduce the low data rate current consumption to less than 400 nA per Hz. 2 Features and benefits * * * * * * * * * 3 Extreme low power, 400 nA per Hz Ultra-fast data output time, ~700 s VDD supply range of 1.95 V to 3.6 V 3 mm x 3 mm, 0.65 mm pitch with visual solder joint inspection 8 g full-scale range 14-bit digital output, 1 mg/LSB sensitivity 1 Output Data Rate (ODR), implementation based from < 1 Hz to 800 Hz 2 I C digital interface 3-axis, 45 tilt outputs Typical applications * * * * Smart grid: tamper detect Anti-theft White goods tilt Remote controls 1 The ODR for this device is user defined by the period of the Enable pulsed signal. The maximum recommended frequency of the Enable signal or the ODR that can be achieved for this device is 800 Hz. MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 4 Ordering information Table 1. Ordering information Part Number Temperature Range Package Shipping MMA8491QT -40 to +85 C QFN 12 Tray MMA8491QR1 -40 to +85 C QFN 12 1000 pc / Tape & Reel MMA8491QR2 -40 to +85 C QFN 12 5000 pc / Tape & Reel 5 Related documentation The MMA8491Q device features and operations are described in a variety of reference manuals, user guides, and application notes. To find the most current versions of these documents: 1. Go to the NXP homepage at: http://www.nxp.com/ 2. In the Keyword search box at the top of the page, enter the device number MMA8491Q. In the Refine Your Result pane on the left, click on the Documentation link. 6 Block diagram Figure 1. Block Diagram 7 Pinout MMA8491Q is hosted in a 12-pin 3 mm x 3 mm QFN package. Ten pins are used for functions; two pins are unconnected. Refer to Table 2 for complete pin descriptions and functions. MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 2 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer NC NC 12 11 MMA8491Q VDD 2 9 Yout SDA 3 8 Zout EN 4 7 Gnd 6 Xout Gnd 10 5 1 SCL Byp Transparent top view Figure 2. Pin connection diagram Table 2. Pin descriptions Pin Symbol Function 1 Byp Internal regulator The internal regulator voltage of 1.8 V is present on this output capacitor pin. Connect to external 0.1 F bypass capacitor. connection 2 VDD Power Supply 3 SDA I C Data I C Slave Data Line, open drain Input/Output 2 * 7-bit I C device address is 0x55 2 * The SDA and SCL I C connections are open drain, and therefore usually require a pull-up resistor 4 EN Enable pin The Enable pin fully turns on the accelerometer system when it is pulled up to logic high. The accelerometer system is turned off when the Enable pin is logic low. 5 SCL I C Clock I C Slave Clock Line, open drain Input 6 Gnd Ground Ground Ground 7 Gnd Ground Ground Ground 8 Zout 9 Yout Push-pull Z-Axis * Output is high when acceleration is > 0.688 g (axis is | Output Tilt Detection | > 45). Output * Output is low when acceleration is 0.688 g (axis is || 45). Push-pull Y-Axis Output * These pins are push-pull output pins. Tilt Detection 2 Description Pin status Output Device power is supplied through the VDD line. Power Input supply decoupling capacitors should be placed as near as possible to pin 1 of the device. 2 2 2 Input Output 10 Xout 11 NC No internal connection No internal connection 12 NC No internal connection No internal connection MMA8491Q Data sheet: Technical data COMPANY PUBLIC Push-pull X-Axis Tilt Detection Output Output All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 3 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 8 Recommended application diagram Figure 3. VDD connects to power supply and EN is pulsed To ensure the accelerometer is fully functional, connect the MMA8491Q as suggested in Figure 3. * A capacitor must be connected to the Bypass pin (pin 1) to assist the internal voltage regulator. It is recommended to use a 0.1 F capacitor. The capacitor should be placed as near as possible to the Bypass pin. * The device power is supplied through the VDD line. The power supply decoupling capacitor should be placed as close as possible to the VDD pin. - Use a 1.0 or 4.7 F capacitor when the VDD and EN are not tied together. - When VDD and EN are tied together, use a 0.1 F capacitor. The 0.1 F capacitor value has been chosen to minimize the average current consumption while still maintaining an acceptable level of power supply high frequency filtering. * Both ground pins (pins 6 and 7) must be connected to ground. 2 * When the I C communication line is used, use a pull-up resistor to connect to line SDA and SCL. The SCL line can be driven by a push-pull driver, in which case, no pull-up resistor is necessary. If SDA and SCL pins are not used, then they should be tied to ground. 9 Sensing direction and output response The MMA8491Q has three tilt detection outputs: Xout, Yout, and Zout. The following figure shows the output results at the six different orientation positions. MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 4 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Top view Side view Portrait Up Back Pin 1 Xout @ 0 g Yout @ 0 g Zout @ -1 g Gravity Xout @ 0 g Yout @ -1 g Zout @ 0 g Landscape Left Front Landscape Right Xout @ 0 g Yout @ 0 g Zout @ 1 g Xout @ -1 g Yout @ 0 g Zout @ 0 g Z Xout @ 1 g Yout @ 0 g Zout @ 0 g Portrait Down X Y Xout @ 0 g Yout @ 1 g Zout @ 0 g (Top view) Reference frame for acceleration measurement Figure 4. Sensitive axes orientation and output response to 1 g (gravity) stimulus 10 Mechanical and electrical specifications 10.1 Absolute maximum ratings Absolute maximum ratings are the limits the device can be exposed to without damage. Functional operation at absolute maximum rating is not guaranteed. Although this device contains circuitry to protect against damage due to high static voltage or electrostatic fields, it is advised that normal precautions be taken to avoid application of any voltage higher than the maximum-rated voltage. Table 3. Absolute maximum ratings Symbol Rating Min Max Unit -- 10 000 V -0.3 3.6 V -- 1.8 m gmax Maximum acceleration (all axes, 100 s) VDD Analog supply voltage Ddrop Drop test TAGOC Operating temperature -40 +85 C TSTG Storage temperature -40 +125 C Table 4. ESD and latch-up protection characteristics Symbol Rating Value Unit VHBM Human body model (HBM) 2000 V VMM Machine model (MM) 200 V MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 5 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Symbol Rating Value Unit VCDM Charge device model (CDM) 500 V ILU Latch-up current at TA = 85 C 100 mA 10.2 Mechanical characteristics Table 5. Accelerometer mechanical characteristics VDD = 2.8 V, T = 25 C, unless otherwise noted. Typical number is the target number, unless otherwise specified. All numbers are based on VDD cap = 4.7 F. Parameter Symbol Full-scale measurement range Sensitivity Conditions Min Typ Max Unit [1] -- -- 8 -- g [2] -- 973 1024 1075 counts/g All axes, all ranges -5 -- 5 % FS So [2] Calibrated sensitivity error CSE Cross-axis sensitivity [1] CXSEN Sensitivity temperature variation Zero-g level temperature variation Zero-g level offset accuracy Zero-g level after board mount Die rotation included -4.2 -- 4.2 % [1] -40 C to +85 C -0.014 -- 0.014 %/C [1] -40 C to +85 C -0.98 -- 0.98 mg/C -- -100 -- 100 mg -- -120 -- 120 mg RMS -- -- 11.5 18 mg-rms [1] -- -- -- 1 %FS 25 C 0.583 0.688 0.780 g -40 C to +85 C 0.577 0.688 0.784 25 C 35.6 43.5 51.3 -40 C to +85 C 35.2 43.5 51.7 -- -40 25 85 TCS TCO [2][3] TyOff [1][4] TyOffPBM [1] Noise Nonlinearity NL [5] Threshold / g-value [6] TDL [1][4][6] TDL Threshold / Tilt angle [7] Temperature range [1] [2] [3] [4] [5] [6] [7] [1] TAGOC degrees C Verified by characterization; not tested in production. Parameters tested 100% at final test at room temperature. Before board mount. Post-board mount offset specifications are based on a 4-layer PCB, relative to 25 C. Internal threshold of output level change (from 0 g reference), g values are calculated from trip angles. All angles are based on the trip angle from static 0 g to 1 g; the g-values are calculated from the trip angle. Internal threshold of output level change (from 0 g reference). MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 6 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 10.3 Electrical characteristics Table 6. Electrical characteristics VDD = 2.8 V, T = 25 C, unless otherwise noted. Typical values represent mean or mean 1 values, depending on the specific parameter. Typical number is the target number unless otherwise specified. All numbers are based on VDD cap = 4.7 F. Symbol Parameter [1] Conditions Min Typ Max Unit -- 1.71 1.8 3.6 V VDD = 2.8 V, EN is pulsed to VDD for 1 ms -- 400 1.8 VDD Supply voltage IDD Supply current in one-shot mode ISD Supply current in shutdown mode VDD = 2.8 V, EN = 0 -- Bypass capacitor at Byp pin -- 70 100 470 nF [2] CBYP [2][3][4] [2][3] [1][5][6] 980 [1][6] 68 nA/Hz nA [1] High level output voltage Xout, Yout, Zout IO = 500 A 0.85 * VDD -- -- V [1] Low level output voltage Xout, Yout, Zout IO = 500 A -- -- 0.15 * VDD V [1] High level input voltage EN VDD = 2.8 V 0.85 * VDD -- -- V VIL [1] Low level input voltage EN VDD = 2.8 V -- -- 0.15 * VDD V [7] VOLS Low level output voltage SDA IO = 3 mA -- -- 0.4 V [7] VIH High level input voltage SDA, SCL VDD = 2.8 V 0.7 * VDD -- -- V [7] Low level input voltage SDA, SCL VDD = 2.8 V -- -- 0.3 * VDD V Output source current Xout, Yout, Zout Voltage high level Vout = 0.85 x VDD, VDD = 2.8 V -- -- 7.3 mA ISINK Output sink current Xout, Yout, Zout Voltage low level Vout = 0.15 x VDD, VDD = 2.8 V -- -- 8.9 mA TON / [8] TACTIVE Turn-on time Measured from the time EN = 1.95 V to valid outputs -- -- VDD = 2.8 V 1000 VOH VOL VIH VIL [1] ISOURCE [1] [7] TRST [1] [2] [3] [4] [5] [6] [7] [8] Reset Time The time between falling edge of EN and next rising edge of EN [2][3][4] 720 -- [1][5][6] s -- s 900 Verified by characterization; not tested in production. Evaluation data: not tested in production. Typical number is mean data. Data is based on typical bypass cap = 100 nF. Data is based on max bypass cap = 470 nF. Over temperature -40 C to 85 C. Guaranteed by design. For application connection, see Figure 3 MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 7 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 2 11 I C Interface 2 Acceleration data may be accessed through an I C interface, thus making the device particularly suitable for direct interfacing with a microcontroller. The MMA8491Q features three interrupt signals that indicate the tilt-sensing results on X, Y, Z axis respectively. 2 The raw accelerometer data are readable via I C at the same time when an interrupt signal is available. 2 The registers embedded inside the MMA8491Q are accessible through the I C serial 2 interface, Table 7. To enable the I C interface, the EN pin must be HIGH. If either EN or 2 2 VDD are absent, the MMA8491Q I C interface reads invalid data. The I C interface may 2 be used for communications along with other I C devices. Removing power from the VDD 2 pin of the MMA8491Q does not affect the I C bus. Table 7. Serial interface pins Pin Description SCL 2 I C Serial Clock SDA I C Serial Data 2 2 There are two signals associated with the I C bus; the Serial Clock Line (SCL) and the Serial Data Line (SDA). The SDA is a bidirectional line used for sending and receiving the data to/from the interface. External pull-up resistors connected to VDD are expected 2 for SDA and SCL. When the bus is free both the lines are HIGH. The I C interface is compliant with Fast mode (400 kHz, Table 8). 2 Table 8. I C slave timing values Parameter Symbol [1] I2C Fast Mode Min Max Unit SCL clock frequency fSCL 0 400 kHz Bus-free time between STOP and START condition tBUF 1.3 -- s (Repeated) START hold time tHD;STA 0.6 -- s Repeated START setup time tSU;STA 0.6 -- s STOP condition setup time tSU;STO 0.6 -- s [2] SDA data hold time tHD;DAT 0.05 0.9 s SDA setup time tSU;DAT 100 -- s SCL clock low time tLOW 1.3 -- s SCL clock high time tHIGH 0.6 SDA and SCL rise time tr SDA and SCL fall time tf [4] SDA valid time SDA valid acknowledge time tVD;DAT [5] -- s [3] 300 s [3] 300 s 20 + 0.1 Cb 20 + 0.1 Cb -- [2] s [2] 0.9 tVD;ACK -- 0.9 s Pulse width of spikes on SDA and SCL that must be suppressed by internal input filter tSP 0 50 s Capacitive load for each bus line Cb -- 400 pF [1] All values referred to VIH(min) (0.3VDD) and VIL(max) (0.7VDD) levels. MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 8 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer [2] [3] [4] [5] This device does not stretch the LOW period (tLOW) of the SCL signal. Cb = total capacitance of one bus line in pF. tVD;DAT = time for data signal from SCL LOW to SDA output (HIGH or LOW, depending on which one is worse). tVD;ACK = time for Acknowledgement signal from SCL LOW to SDA output (HIGH or LOW, depending on which one is worse). 2 Figure 5. I C slave timing diagram 2 11.1 I C read operations The transaction on the bus is started through a start condition (START) signal. A START condition is defined as a HIGH-to-LOW transition on the data line while the SCL line is held HIGH. After START has been transmitted by the Master, the bus is considered busy. The next byte of data transmitted after START contains the slave address in the first seven bits, and the eighth bit tells whether the Master is receiving data from the slave or transmitting data to the slave. When an address is sent, each device in the system compares the first seven bits after a start condition with its address. If they match, then the device considers itself addressed by the Master. The ninth clock pulse, following the slave address byte, and each subsequent byte, is the acknowledge (ACK). The transmitter must release the SDA line during the ACK period. The receiver must then pull the data line LOW so that it remains stable low during the high period of the acknowledge clock period. A LOW-to-HIGH transition on SDA while SCL is HIGH is defined as a stop condition (STOP). A data transfer is always terminated by a STOP. A Master may also issue a repeated START during a data transfer. The MMA8491Q expects repeated STARTs to be used to randomly read from specific registers. The MMA8491Q accelerometer standard 7-bit slave address is 01010101(0x55). MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 9 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 2 Table 9. I C device address sequence Command [7:1] Device Address [7:1] Device Address [0] R/W [7:0] 8-bit Final Value Read 01010101 0x55 1 0xAB Write 01010101 0x55 0 0xAA 11.1.1 Single-byte read The transmission of an 8-bit command begins on the falling edge of SCL. After the 8 clock cycles are used to send the command, note that the data returned is sent with the MSB first after the data is received. Figure 6 shows the timing diagram for the 2 accelerometer 8-bit I C read operation. 1. The Master (or MCU) transmits a start condition (ST) to the MMA8491Q, slave address (0x55), with the R/W bit set to "0" for a write, and the MMA8491Q sends an acknowledgement. 2. Then the Master (or MCU) transmits the address of the register to read and the MMA8491Q sends an acknowledgement. 3. The Master (or MCU) transmits a repeated start condition (SR) and then addresses the MMA8491Q (0x1D) with the R/ W bit set to 1 for a read from the previously selected register. 4. The Slave then acknowledges and transmits the data from the requested register. 5. The Master does not acknowledge (NAK) the transmitted data, but transmits a stop condition to end the data transfer. 11.1.2 Multiple-byte read When performing a multiple-byte read or burst read, the MMA8491Q automatically increments the received register address commands after a read command is received. Therefore, after following the steps of a single-byte read, multiple bytes of data can be read from sequential registers after each MMA8491Q acknowledgment (AK) is received, until a no acknowledge (NAK) occurs from the Master, followed by a stop condition (SP) signaling an end of transmission. MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 10 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 11.1.3 I2C data sequence diagrams Single-byte read ST Master Device Address[7:1] Register Address[7:0] W AK Slave Device Address[7:1] SR NAK R AK AK SP Data[7:0] Multiple-byte read ST Master Device Address[7:1] Register Address[7:0] W AK Slave Device Address[7:1] SR R AK AK AK Data[7:0] c o n tin u ed . . . AK Master AK Data[7:0] Slave NAK SP Data[7:0] Data[7:0] Legend ST: Start Condition SP: Stop Condition NAK: No Acknowledge SR: Repeated Start Condition AK: Acknowledge R: Read = 1 W: Write = 0 2 Figure 6. I C data sequence diagrams 12 Modes of operation EN = Low OFF* Mode VDD = On SHUTDOWN Mode VDD = Off EN = Don't Care One sample is acquired EN = High VDD = On EN = Low ACTIVE Mode VDD = On EN = High STANDBY Mode VDD = On EN = High *OFF mode can be entered from any state by removing the power. Figure 7. MMA8491Q operating modes Table 10. MMA8491Q operating modes Mode Conditions Function description Digital output state OFF VDD = OFF EN = Don't Care Device is powered off. Hi-Z SHUTDOWN VDD = ON EN = Low All blocks are shut down. Hi-Z MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 11 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Mode Conditions Function description Digital output state ACTIVE VDD = ON EN = High All blocks are enabled. Deasserted, Xout = 0, Yout= 0, Zout = 0 Device enters Standby mode automatically after data conversion. STANDBY VDD = ON EN = High Only digital output subsystem is enabled. Data is valid and available only in this stage. 2 Active, I C outputs become valid 12.1 ACTIVE mode The accelerometer subsystem is turned on at the rising edge of the EN pin, and acquires one sample for each of the three axes. Note that EN should not be asserted before VDD reaches 1.95 V. Samples are acquired, converted, and compensated for zero-g offset and gain errors, and then compared to an internal threshold value of 0.688 g and stored. * If any of the X, Y, Z axes sample's absolute value > this threshold, then the corresponding outputs on these axes drive logic highs. * If any of the X, Y, Z axes sample's absolute value this threshold, then the corresponding outputs on these axes drive logic lows. Read register 00h in this stage to determine whether the sample data is ready to be read. 12.2 STANDBY mode The device enters STANDBY mode automatically after the previously described function (powers into SHUTDOWN mode, ACTIVE mode) is accomplished. The digital output 2 system outputs valid data, which can also be read via the I C communication bus. This is the appropriate phase to read the measured data, either from the three push-pull logic 2 outputs or through the I C transaction. All other subsystems are turned off. These outputs are held until the MMA8491Q operation mode changes. For lower power consumption, deassert the EN pin as soon as data is read (to enter SHUTDOWN mode). 12.3 Next sample acquisition The MMA8491Q needs to be brought back to the ACTIVE mode again by pulling EN pin up to a Logic 1. Another option is to power down the device and start from OFF mode as illustrated in Figure 7. For applications where sampling intervals are greater than 30 seconds, the host can shut off the tilt sensor power after acquisition of tilt sensor output data to conserve energy and prolong battery life. 12.4 Power-up timing sequences The power-up timing sequence for MMA84591Q is shown in the following figure, where VDD is powered and the EN pin is activated to acquire a single sample. Additional samples can be acquired by repeating the EN pulse. MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 12 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer OFF ACTIVE SHUTDOWN STANDBY SHUTDOWN VDD EN Hi-Z Data Available Data tON Figure 8. MMA8491Q timing sequence tON is the time between EN to the end of ACTIVE stage, after which the newly acquired sample data is available. 12.5 45 tilt detection The output value changes according to the absolute value of the acceleration of the MMA8491Q compared to the threshold: * When the acceleration's absolute value > the threshold 0.688 g, the output = 1. * When the acceleration's absolute value the threshold, the output = 0. For example, * When the MMA8491Q is set on a table, it senses 1 g acceleration on Z-axis and senses 0 g on X- and Y-axes. * When the MMA8491Q is flipped upside down on the table, it senses -1 g acceleration on Z-axis and senses 0 g on X- and Y-axes. In both cases Xout = 0, Yout = 0, and Zout = 1. 12.6 Tilt angle Tilt angles can be calculated from the g-value threshold using the equation below. The tilt threshold is 0.688 g, which corresponds to 43.5. Figure 9 illustrates the tilt angle threshold. ( g-value Tilt Angle = asin ------------------1g ) * When 0 g acceleration is present on an axis, the tilt angle = 0; when 1 g acceleration is present on an axis, the tilt angle = 90. * When the tilt angle > the tilt threshold, the output for the axis is HIGH; when the tilt angle the tilt threshold, the output for the axis is LOW. MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 13 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Tilt Angle = 55 Output = 1 O Horizontal Reference Projected g-value = Threshold (g-value) = 0.688g Threshold = 0.688g 1g O O Horizontal Reference Horizontal Reference 0.688g 0.688g 1g Tilt Angle = 30 1g Output = 0 Tilt Angle = 70 Output = 1 Figure 9. MMA8491Q output is based on tilt angle and sensor g-value MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 14 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 13 Register descriptions Table 11. Register address map Name Type Register Address Autoincrement [1] Address Reset STATUS R 0x00 0x01 0x00 OUT_X_MSB R 0x01 0x02 Output [7:0] are the 8 MSBs of the 14-bit sample OUT_X_LSB R 0x02 0x03 Output [7:2] are the 6 LSBs of the 14-bit sample OUT_Y_MSB R 0x03 0x04 Output [7:0] are the 8 MSBs of the 14-bit sample OUT_Y_LSB R 0x04 0x05 Output [7:2] are the 6 LSBs of the 14-bit sample OUT_Z_MSB R 0x05 0x06 Output [7:0] are the 8 MSBs of the 14-bit sample OUT_Z_LSB R 0x06 0x00 Output [7:2] are the 6 LSBs of the 14-bit sample [1] 2 Comment Read time status 2 Auto-increment is the I C feature that the I C read address is automatically updated after each read. Auto-increment addresses that are not a simple 2 increment are highlighted in bold. The auto-increment addressing is only enabled when device registers are read using I C burst read mode. Therefore the internal storage of the auto-increment address is cleared whenever a stop-bit is detected. Notes: * Register contents are preserved when EN pin is set high after sampling. * Register contents are reset when EN pin is set low. 13.1 STATUS - Status register (address 00h) Register 0x00 reflects the real-time status information of the X, Y, and Z sample data. The data read bits (ZYXDR, ZDR, YDR, XDR) are set when samples are taken and ready to be read. Table 12. STATUS - Status register (address 00h) bit allocation Bit 7 6 Symbol 5 4 -- 3 2 1 0 ZYXDR ZDR YDR XDR Reset 0 0 0 0 0 0 0 0 Access R R R R R R R R Table 13. STATUS - Status register (address 00h) field descriptions Field 3 ZYXDR 2 ZDR Description X-, Y-, Z-axis new Data Ready (and available) * ZYXDR signals that a new sample for all channels is available. * ZYXDR is cleared when the high-bytes of the acceleration data (OUT_X_MSB, OUT_Y_MSB, OUT_Z_MSB) of all channels are read.. 0: No new set of data ready (default value) 1: A new set of XYZ acceleration and temperature data is available Z-axis new Data Ready (and available) * ZDR is set whenever a new acceleration sample related to the Z-axis is generated. * ZDR is cleared anytime OUT_Z_MSB register is read. 0: No new Z-axis data is ready (default value) 1: A new Z-axis data is ready MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 15 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Field Description 1 YDR Y-axis new Data Ready (and available) * YDR is set whenever a new acceleration sample related to the Y-axis is generated. * YDR is cleared anytime OUT_Y_MSB register is read. 0: No new Y-axis data ready (default value) 1: A new Y-axis data is ready 0 XDR X-axis new Data Ready (and available) * XDR is set whenever a new acceleration sample related to the X-axis is generated. * XDR is cleared anytime OUT_X_MSB register is read. 0: No new X-axis data ready (default value) 1: A new X-axis data is ready 13.2 Output data registers (addresses 01h to 06h) These registers contain the X-axis, Y-axis, and Z-axis14-bit output sample data (expressed as 2's complement numbers). * OUT_X_MSB, OUT_X_LSB, OUT_Y_MSB, OUT_Y_LSB, OUT_Z_MSB, and OUT_Z_LSB are stored in the autoincrementing address range of 0x01 - 0x06. * The LSB registers can only be read immediately following the read access of the corresponding MSB register. A random read access to the LSB registers is not possible. * Reading the MSB register and then the LSB register in sequence ensures that both bytes (LSB and MSB) belong to the same data sample, even if a new data sample arrives between reading the MSB and the LSB byte. * The accelerometer data registers should be read only after the status register has confirmed that new data on all axes is available. Table 14. OUT_X_MSB - Output data register (address 01h) bit allocation Bit 7 6 5 4 Symbol 3 2 1 0 XD[13:6] Reset 0 0 0 0 0 0 0 0 Access R R R R R R R R 1 0 -- -- Table 15. OUT_X_LSB - Output data register (address 02h) bit allocation Bit 7 6 5 Symbol 4 3 2 XD[5:0] Reset 0 0 0 0 0 0 0 0 Access R R R R R R R R MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 16 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Table 16. OUT_Y_MSB - Output data register (address 03h) bit allocation Bit 7 6 5 4 Symbol 3 2 1 0 YD[13:6] Reset 0 0 0 0 0 0 0 0 Access R R R R R R R R 2 1 0 -- -- Table 17. OUT_Y_LSB - Output data register (address 04h) bit allocation Bit 7 6 5 Symbol 4 3 YD[13:6] Reset 0 0 0 0 0 0 0 0 Access R R R R R R R R 3 2 1 0 Table 18. OUT_Z_MSB - Output data register (address 05h) bit allocation Bit 7 6 5 4 Symbol OUT_Z[7:0] Reset 0 0 0 0 0 0 0 0 Access R R R R R R R R 2 1 0 -- -- Table 19. OUT_Z_LSB - Output data register (address 06h) bit allocation Bit 7 6 5 Symbol 4 3 ZD[5:0] Reset 0 0 0 0 0 0 0 0 Access R R R R R R R R 13.3 Accelerometer output conversion Table 20. Accelerometer output data 14-bit Data Range 8 g (1 mg/count) 01 1111 1111 1111 +8.000 g 01 1111 1111 1110 +7.998 g ... ... 00 0000 0000 0000 0.000 g 11 1111 1111 1111 -0.001 g ... ... 10 0000 0000 0001 -7.998 g 10 0000 0000 0000 -8.000 g MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 17 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 14 Mounting guidelines Surface-mount printed circuit board (PCB) layout is a critical portion of the total design. The footprint for the surface mount package must be the correct size to ensure proper solder connection interface between the PCB and the package. With the correct footprint, the package will self-align when subjected to a solder reflow process. The purpose is to minimize the stress on the package after board mounting. The MMA8491Q accelerometers use the QFN package. This section describes suggested methods of soldering and mounting these devices to the PCB for consumer applications. 14.1 Overview of soldering considerations The information provided here is based on experiments executed on QFN devices. They do not represent exact conditions present at a customer site. Therefore, information herein should be used as guidance only, and process and design optimizations are recommended to develop an application specific solution. It should be noted that with the proper PCB footprint and solder stencil designs, the package will self-align during the solder reflow process. 14.2 Halogen content This package is designed to be Halogen Free, exceeding most industry and customer standards. Halogen Free means that no homogeneous material within the assembly package shall contain chlorine (Cl) in excess of 700 ppm or 0.07% weight/weight or bromine (Br) in excess of 900 ppm or 0.09% weight/weight. 14.3 PCB mounting recommendations * Do not solder down the six exposed pads under the package, thus minimizing boardmounting stress impact to product performance. * PCB landing pad is 0.675 mm x 0.325 mm as shown in Figure 10. * Solder mask opening = PCB land pad edge + 0.2 mm larger all around. * Stencil opening size is 0.625 mm x 0.3 mm. * Stencil thickness is 100 m or 125 m. * The solder mask should not cover any of the PCB landing pads, as shown in Figure 10. * No additional via nor metal pattern underneath package on the top of the PCB layer. * Do not place any components or vias within 2 mm of the package land area. This may cause additional package stress if it is too close to the package land area. * Signal traces connected to pads should be as symmetric as possible. Put dummy traces on NC pads, to have the same length of exposed trace for all pads. * Use a standard pick-and-place process and equipment. Do not use a hand soldering process. * Customers are advised to be cautious about the proximity of screw-down holes to the sensor, and the location of any press fit to the assembled PCB when in an enclosure. It is important that the assembled PCB remain flat after assembly to keep electronic operation of the device optimal. * The PCB should be rated for the multiple lead-free reflow condition with a maximum 260 C temperature. * NXP sensors are compliant with Restrictions on Hazardous Substances (RoHS), having halide-free molding compound (green) and lead-free terminations. These MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 18 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer terminations are compatible with tin-lead (Sn-Pb) as well as tin-silver-copper (Sn-AgCu) solder paste soldering processes. Reflow profiles applicable to those processes can be used successfully for soldering the devices. Figure 10. PCB footprint guidelines MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 19 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 15 Package Information The MMA8491Q uses a 12-lead QFN package, case number 98ASA00290D. 15.1 Tape and reel information Figure 11. Tape dimensions Pin 1 Direction to unreel Barcode label side of reel Figure 12. Tape and reel orientation 15.2 Package description This drawing is available for download at http://www.nxp.com/files/shared/doc/ package_info/98ASA00290D.pdf. Please consult the most recently issued drawing before initiating or completing a design. MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 20 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Figure 13. Case 2169-02, Issue X1, 12-Lead QFN--page 1 MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 21 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Figure 14. Case 2169-02, Issue X1, 12-Lead QFN--page 2 MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 22 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Figure 15. Case 2169-02, Issue X1, 12-Lead QFN--page 3 MMA8491Q Data sheet: Technical data COMPANY PUBLIC All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 23 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 16 Revision history Revision number Revision date 1.0 10/2012 * Initial release 2.0 11/2012 * Characterization data verified to be complete and final 2.1 4/2016 * * * * MMA8491Q Data sheet: Technical data COMPANY PUBLIC Description Added MMA8491QR2 to Ordering information table Added paragraphs describing absolute maximum ratings Revised package dimensions drawings to the NXP format, no technical changes The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors * Legal texts have been adapted to the new company name where appropriate All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 24 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer 17 Legal information Data sheet status [1] [2] Document status Product status Data sheet: Product preview Development This document contains information on a product under development. NXP reserves the right to change or discontinue this product without notice. Data sheet: Advance information Qualification This document contains information on a preproduction product. Specifications and pre-production information herein are subject to change without notice. Data sheet: Technical data Production NXP reserves the right to change the production detail specifications as may be required to permit improvements in the design of its products. [1] [2] Please consult the most recently issued document before initiating or completing a design. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL nxp.com. Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. MMA8491Q Data sheet: Technical data COMPANY PUBLIC Definition Disclaimers Information in this document is provided solely to enable system and software implementers to use NXP products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based on the information in this document. NXP reserves the right to make changes without further notice to any products herein. NXP makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does NXP assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in NXP data sheets and/ or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including "typicals," must be validated for each customer application by customer's technical experts. NXP does not convey any license under its patent rights nor the rights of others. NXP sells products pursuant to standard terms and conditions of sale, which can be found at the following address: nxp.com/salestermsandconditions. Trademarks NXP, the NXP logo, Freescale, the Freescale logo and SMARTMOS are trademarks of NXP B.V. All other product or service names are the property of their respective owners. All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 25 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Tables Tab. 1. Tab. 2. Tab. 3. Tab. 4. Tab. 5. Tab. 6. Tab. 7. Tab. 8. Tab. 9. Tab. 10. Tab. 11. Tab. 12. Tab. 13. Ordering information ..........................................2 Pin descriptions .................................................3 Absolute maximum ratings ................................5 ESD and latch-up protection characteristics ......5 Accelerometer mechanical characteristics ........ 6 Electrical characteristics ....................................7 Serial interface pins .......................................... 8 I2C slave timing values ..................................... 8 I2C device address sequence .........................10 MMA8491Q operating modes ......................... 11 Register address map ..................................... 15 STATUS - Status register (address 00h) bit allocation ......................................................... 15 STATUS - Status register (address 00h) field descriptions ..................................................... 15 MMA8491Q Data sheet: Technical data COMPANY PUBLIC Tab. 14. Tab. 15. Tab. 16. Tab. 17. Tab. 18. Tab. 19. Tab. 20. OUT_X_MSB - Output data register (address 01h) bit allocation ............................. 16 OUT_X_LSB - Output data register (address 02h) bit allocation ............................................16 OUT_Y_MSB - Output data register (address 03h) bit allocation ............................. 17 OUT_Y_LSB - Output data register (address 04h) bit allocation ............................................17 OUT_Z_MSB - Output data register (address 05h) bit allocation ............................. 17 OUT_Z_LSB - Output data register (address 06h) bit allocation ............................................17 Accelerometer output data .............................. 17 All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 26 / 28 MMA8491Q NXP Semiconductors 3-Axis Multifunction Digital Accelerometer Figures Fig. 1. Fig. 2. Fig. 3. Fig. 4. Fig. 5. Fig. 6. Fig. 7. Fig. 8. Block Diagram ...................................................2 Pin connection diagram .....................................3 VDD connects to power supply and EN is pulsed ................................................................ 4 Sensitive axes orientation and output response to 1 g (gravity) stimulus ................... 5 I2C slave timing diagram .................................. 9 I2C data sequence diagrams .......................... 11 MMA8491Q operating modes ......................... 11 MMA8491Q timing sequence .......................... 13 MMA8491Q Data sheet: Technical data COMPANY PUBLIC Fig. 9. Fig. 10. Fig. 11. Fig. 12. Fig. 13. Fig. 14. Fig. 15. MMA8491Q output is based on tilt angle and sensor g-value .................................................14 PCB footprint guidelines ..................................19 Tape dimensions ............................................. 20 Tape and reel orientation ................................ 20 Case 2169-02, Issue X1, 12-Lead QFN-- page 1 ............................................................. 21 Case 2169-02, Issue X1, 12-Lead QFN-- page 2 ............................................................. 22 Case 2169-02, Issue X1, 12-Lead QFN-- page 3 ............................................................. 23 All information provided in this document is subject to legal disclaimers. Rev. 2.1 -- 26 April 2016 (c) NXP B.V. 2016. All rights reserved 27 / 28 NXP Semiconductors MMA8491Q 3-Axis Multifunction Digital Accelerometer Contents 1 2 3 4 5 6 7 8 9 10 10.1 10.2 10.3 11 11.1 11.1.1 11.1.2 11.1.3 12 12.1 12.2 12.3 12.4 12.5 12.6 13 13.1 13.2 13.3 14 14.1 14.2 14.3 15 15.1 15.2 16 17 General description ............................................ 1 Features and benefits .........................................1 Typical applications ............................................1 Ordering information .......................................... 2 Related documentation ...................................... 2 Block diagram ..................................................... 2 Pinout ................................................................... 2 Recommended application diagram ..................4 Sensing direction and output response ............4 Mechanical and electrical specifications .......... 5 Absolute maximum ratings ................................ 5 Mechanical characteristics .................................6 Electrical characteristics .................................... 7 I2C Interface ........................................................ 8 I2C read operations ...........................................9 Single-byte read .............................................. 10 Multiple-byte read ............................................ 10 I2C data sequence diagrams ...........................11 Modes of operation ...........................................11 ACTIVE mode ..................................................12 STANDBY mode ..............................................12 Next sample acquisition ...................................12 Power-up timing sequences ............................ 12 45 tilt detection ...............................................13 Tilt angle .......................................................... 13 Register descriptions ....................................... 15 STATUS - Status register (address 00h) ......... 15 Output data registers (addresses 01h to 06h) .. 16 Accelerometer output conversion .................... 17 Mounting guidelines ......................................... 18 Overview of soldering considerations .............. 18 Halogen content .............................................. 18 PCB mounting recommendations .................... 18 Package Information .........................................20 Tape and reel information ............................... 20 Package description ........................................ 20 Revision history ................................................ 24 Legal information .............................................. 25 (c) NXP B.V. 2016. All rights reserved For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Released on 26 April 2016