HS-220 Series Digital Output Hall Effect Sensor SENSORS AND CONTROLS GROUP ey 0988 10.789 - 9.366 10.27) 0.187 14.78] + 190 | NOM 1 to _ CENTER LINE OF HALL CELL LOCATION tener oe 9.310 17.871 0.187 14.76) - 0.200 (7.971 NOM | Lt ao O78 Is01 ti 9.400 (10.181 cL ot 0.080 11271 be 0,100 (2.64) NOM 0.888 (22.48) ~ ~~ 0.018 (0.481 ' 0.866 121.07) NOM DIMENSIONS ARE iN Vee > OUTPUT 0080 127) INCHES [MILLIMETERS] 0.082 11.87) } t : NOM Sie Tepe x j : 1 4 0126 19181 - GN 0.002 [1.571 DIA NOM 8 Features * available with wire leads " Voc range: 4.5 to 24 volts open-collector output two sensor options fully TTL compatible Description The HS-220 Hall effect sensor consists of a choice between an ultra-sensitive switch {HS-220-40) or a latch (HS-220-75); see alec- trical specifications and typical characteristics on the next sheet for details. Switching takes place when an external magnetic source of sufficient strength moves within the effective proximity of the sensor. These sensors ara ideal for environments where dust or oil pre- vents the use of an optoelectronic sensor. Call OptoSwitch for applications assistance. Absolute Maximum Ratings (T, = 25C unless otherwise stated.) Storage Temperature 85C to +150C Operating Temperature .. -OC to +70C Lead Soldering Temperature) cst wesw 240C) Supply Voltage ... Power Dissipation... Notes: 1. Add a-W suffix to order with 12 (305mm) wire leads. Wire is 26 AWG, seven (7) strand, with UL1429 insulation or equivalent. .250mw4) Red.... Biack.. White .... 2. 0.06" (1.5mm) from the case for 5 seconds maximum. (device leads only) 3. 260C maximum when wave soldering. (device leads only) 4. No derating required; maximum power dissipation allowed at 70C. SWITCH POINT vs TEMPERATURE Fundamental Characteristics SWITCH POINT va TEMPERATURE 200 200 7 fon af eae en een | 3 , OPERATE : DB ONT | 4 g 100 , g ; 9 9 ' . | : RELEASE 2 g = 3 10 1 t 0 f 5 | 78 rae : I -200 | -.- - fon -200 - --+ + _ ops ! i : | 90 0 w x 0 70 9 0 0 30 50 70 0 TEMPERATURE (C) TEMPERATURE (C) OptoSwitch + 1500 International Parkway, Suite 100 Richardson, Texas 75081 Phone: 214-479-1122 * 800-448-2900 CLAROSTAT Sensors and Controls 90 HS-220 Series Digital Output Hall Effect Sensor Electrical Characteristics (T, = 25C unless otherwise stated) Symbol | Parameter min max units | Test Conditions Veco Supply Voltage Range 45 24.0 Vv lec Current Drain - 14 mA = |Voc = 24V, Output open Bop | Operate Point {) HS-220-40 - 200 gauss |4.5<Vocos 24V HS-220-75 25 170 gauss (4.5<Voco < 24V Bap | Release Point {1) HS-220-40 50 . gauss 14.5<Voco < 24V HS-220-75 -170 -25 gauss [4.5 <Voo $ 24V Buys | Hysteresis ') HS-220-40 20 - gauss |[4.5<Voco 5 24V HS-220-75 100 : gauss |[4.5<Voco < 24V Vor Output Voltage - 0.4 Vv 4.5 < Voc $ 24V, Io, = 15mMA low Output Leakage Current HS-220-40 - 20 pA | Vgc = 5V. Vout = 24V, B 2 Bop HS-220-75 - 1.0 vA | Veco = 5V, Vout = 24V, BS Bap Notes: 1. See also typical characteristics below. Design Characteristics at T, = 25C (not guaranteed by test) Symbol | Parameter | value | units | Conditions HS-220-40 Bop | Operate Point 150 gauss 14.5<Vcc s 24V Bae Release Point 100 gauss [4.55 Voco S$ 24V Buys | Hysteresis 50 gauss 14.5 < Voc 24V t, Output Rise time 15 ns [Voc = 12V, R, = 820Q, C, = 20pF ty Output Fall time 100 ns |Voec = 12V, R, = 8202, C, = 20pF HS-220-75 Bop _| Operate Point 100 gauss |4.5<Voc $ 24V Bap Release Point -100 | gauss |4.5<Voc s 24V Buys | Hysteresis 200 gauss 14.5 <Voco 5 24V t, Output Rise time 100 nS |Voeo = 12V, Ry = 8200, C, = 20pF ty Output Fall time 200 ns |Voco = 12V, Ry = 8200, C, = 20pF OptoSwitch + 1500 International Parkway, Sulte 100 + Richardson, Texas 75081 Phone: 214-479-1122 + 800-448-2900 CLAROSTAT Sensors and Controls 91