Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer
'
s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer
'
sproductsor
equipment.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
D1207 MS PC 20071127-S00005 / 52307 MS PC 20070201-S00003 / 31407 MS PC 20061127-S00001 No.A0650-1/6
LV8082LP
Overview
The LV8082LP is a Constant-voltage 1ch + Constant-current 1ch driver that supports low-voltage operation. It is optimal
for constant-voltage and constant-current drive of voice coil motors (AF and Shutter) in portable equipment such as
camera cell phones.
Features
Constant-voltage 1ch + Constant-current 1ch H-bridge driver
Built-in power supply switch and position detection comparator for use with a photoreflector
Implemented in a low-power MOS IC process.
Ultraminiature easy to solder VCT16 package (2.6 × 2.6mm)
Built-in thermal protection and low-voltage sensing circuits
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter Symbol Conditions Ratings Unit
Maximum supply voltage VCC max 6.5 V
Output voltage VOUT max OUT1, OUT2, OUT3, OUT4 6.5 V
Input voltage VIN max IN1, IN2, IN3, IN4 -0.3 to +6.5 V
Ground pin source current IGND Per channel 400 mA
Allowable power dissipation Pd max Mounted on a circuit board.* 700 mW
Operating temperature Topr -30 to +85 °C
Storage temperature Tstg -40 to +150 °C
* Specified circuit board : 50×40×0.8mm3 : 4-layer (2S2P) glass epoxy printed circuit board
Bi-CMOS LSI
Constant-voltage 1ch +
Constant-current 1ch H-Bridge
Orderin
g
numbe
r
: ENA0650B
http://semicon.sanyo.com/en/network
LV8082LP
No.A0650-2/6
Allowable Operating Ratings at Ta = 25°C
Parameter Symbol Conditions Ratings Unit
Supply voltage VCC 2.5 to 6.0 V
High-level input voltage VIH 0.53VCC or more V
Low-level input voltage VIL
IN1, IN2, IN3, IN4
Up to 0.2VCC V
Electrical Characteristics at Ta = 25°C, VCC = 3.0V
Ratings
Parameter Symbol Conditions min typ max
Unit
ICCO IN = 0V 0.1 1 µA Current drain
ICCO1 IN = 3V 0.7 1 mA
Ron1 VCC = 3.0V (High and low side total)
IN = 3.0V, IOUT = 100mA 2.0 3.0 Output on resistance
Ron2 VCC = 5.0V (High and low side total)
IN = 5.0V, IOUT = 100mA 1.50 2.0
Constant-voltage output 1 VOUT1 VC = 1V, VCC = 3.0V 1.94 2.0 2.06 V
Constant-current output 1 IOUT1 Between RFG and ground : 1 95 100 105 mA
Constant-current output 2 IOUT2 Between RFG and ground : 0.5
(Design specification) 190 200 210 mA
Output turn-on time Trise With RFG shorted to ground (Design
specification) 1.5 3 µs
Output turn-off time Tfall With RFG shorted to ground (Design
specification) 0.2 0.65 µs
Comparator threshold high-level
voltage VH 1.3 1.37 V
Comparator threshold Low-level
voltage VL 0.86 0.91 V
Comparator hysteresis Vhys 0.39 V
Input current IIN V
IN = 3V 15 30 µA
Note : The design specification items are design guarantees and are not measured.
Package Dimensions Pin Assignment
unit : mm (typ) (VCT16)
3318
2.6
2.6
0.4
0.8
0.25
(0.035)
SIDE VIEW
SIDE VIEW
BOTTOM VIEW
TOP VIEW
LASER MARKED
INDEX 0.5
(0.55)
(C0.116)
(0.13)
(0.125)
12
16
SANYO : VCT16(2.6X2.6)
PGND
OUT1
OUT2
OUT3
OUT4 IN2
COMPOU
T
GND
COMPIN
(NC)
Top View
1
16 15 14 13
5 6 7 8
2
3
4
12
11
10
9
RFG IN3 IN4 IN1
VCC VC
LV8082LP
No.A0650-3/6
Block Diagram
Constant-voltage calculation : VOUT = VC × 2 Example : When an VOUT of 2V is required, VC must be 1V
Constant-current calculation : IOUT = 0.1 ÷ RF Example : When an IOUT of 100mA is required, RF must be 1.
Usage Notes
The constant current is set by the resource RF connected between RFG and grou nd acc o rding to the fo r mula shown
above.
Truth Table
Input Output
IN1 IN2 IN3 IN4 OUT1 OUT2 OUT3 OUT4 Mode
Low Low Off Off Standby mode
Low High Low High Channel 1, constant voltage, reverse
High Low High Low Channel 1, constant voltage, forward
High High
Low Low
Low Low
Off Off
Channel 1, brake mode
Low Low Off Off Standby mode
Low High Low High Channel 2, constant current, reverse
High Low High Low Channel 2, con s tant current, forward
Low Low
High High
Off Off
Low Low Channel 2, brake mode
Note : When off, a high-impedance state.
VCC VCC
0.1V
RFG RF
IN1
IN2
IN3
IN4
LVS TSD
VCC
PGND
VC
AF
(VCM)
1.3V
VC
COMPOUTCOMPIN
SH
(VCM)
GND
L
O
G
I
C
LV8082LP
No.A0650-4/6
Timing Chart
(1) Constant voltage channel timing chart
(2) Constant current channel timing chart
Mode
IN1
OUT1
IN2
OUT2
Standby Reverse BrakeForward
OFF HLL
OFF LLH
LH HL
LL HH
Mode
IN3
OUT3
IN4
OUT4
Standby Reverse BrakeForward
OFF HLL
OFF LLH
LH HL
LL HH
LV8082LP
No.A0650-5/6
Photosensor Position Detection Application Circui t Example
(a) Application circuit
(b) Timing chart
VCC
IN
COMPIN
1.3V Hysteresis : 0.39 V
Microcontroller
power supply
Transistor drive region
COMPOUT
COMPIN
VCC
COMPOUT
10k
Tr
IC peripheral circuits : Position sensor block
Sensor power supply Microcontrolle
r
power supply
IC internal circuits :
Position detection circuit
LV8082LP
PS No.A0650-6/6
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
This catalog provides information as of December, 2007. Specifications and information herein are subject
to change without notice.