Visit our website: www.e2v.com
for the latest version of the datasheet
e2v semiconductors SAS 2007
PC7447A
PowerPC 7447A RISC Microprocessor
Datasheet
0833E–HIREL–01/07
Features
3000 Dhrystone 2.1 MIPS at 1.3 GHz
Selectable Bus Clock (30 CPU Bus Dividers up to 28x)
Selectable MPx/60x Interface Voltage (1.8V, 2.5V)
PD Typically 18W at 1.33 GHz at VDD = 1.3V; 8.0W at 1 GHz at VDD = 1.1V
Full Operating Conditions
Nap, Doze and Sleep Power Saving Modes
Superscalar (Four Instructions Fetched Per Clock Cycle)
4 GB Direct Addressing Range
Virtual Memory: 4 Hexabytes (252)
64-bit Data and 36-bit Address Bus Interface
Integrated L1: 32 KB Instruction and 32 KB Data Cache
Integrated L2: 512 KB
11 Independent Execution Units and three Register Files
Write-back and Write-through Operations
fINT Max = 1.167 MHz
fBUS Max = 133 MHz/166 MHz
Description
The PC7447A host processor is a high-performance, low-power, 32-bit implementations of the PowerPC® Reduced
Instruction Set Computer (RISC) architecture combined with a full 128-bit implementation of Freescale’s AltiVec
technology.
This microprocessor is ideal for leading-edge embedded computing and signal processing applications. The PC7447A fea-
tures 512 KB of on-chip L2 cache. The PC7447A microprocessor has no backside L3 cache, allowing for a smaller
package designed as a pin-for-pin replacement for the PC7447 microprocessor. This device benefits from a silicon-on-
insulator (SOI) CMOS process technology, engineered to help deliver tremendous power savings without sacrificing speed.
A low-power version of the PC7447A microprocessor is also available.
Figure 1-1 on page 2 shows a block diagram of the PC7447A. The core is a high-performance superscalar design support-
ing a double-precision floating-point unit and a SIMD multimedia unit. The memory storage subsystem supports the MPX
bus protocol and a subset of the 60x bus protocol to the main memory and other system resources.
Note that the PC7447A is a footprint-compatible, drop-in replacement in a PC7447 application if the core power supply is
1.3V.
Screening
Full Military Temperature Range (TJ = -55°C, +125°C)
Industrial Temperature Range (TJ = -40°C, +110°C)
2
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
1. Block Diagram
Figure 1-1. PC7447A Microprocessor Block Diagram
Additional Features
• Time Base Counter/Decrementer
Clock Multiplier
JTAG/COP Interface
Thermal/Power Management
Performance Monitor
Dynamic Frequency Switching (DFS)
Temperature Dioder
+
x ÷
FPSCR
FPSCR
PA
+ x ÷
Instruction Unit Instruction Queue
(12-Word)
96-Bit (3 Instructions)
Reservation
32-Bit
Floating-
Point Unit
64-Bit
Load/Store Unit
(EA Calculation)
Finished
32-Bit
Completion Unit
(16-Entry)
36-bit 64-bit
Stations (2)
FPR File
16 Rename
Buffers
GPR File
16 Rename
Buffers
VR File
16 Rename
Buffers
64-Bit
128-Bit
128-Bit
Completes up
SRs
(Shadow) 128-Entry
ITLB
Stores
Load Miss
CTR
LR
Vector Touch Engine
32-Bit
EA
L1 Castout
Status
L2 Store Queue (L2SQ)
Vector
FPU
Vector
Integer
Unit 1
Vector
Integer
Unit 2
Vector
Permute
Unit
Status
Block 1 (32-Byte)
Memory Subsystem
Snoop Push/
Interventions
L1 Castouts
Bus Accumulator
L1 Push
(4)
to three
per clock
instructions
L1 Load Queue (LLQ)
L1 Load Miss (5)
Instruction Fetch (2)
Cacheable Store Request (1)
L1 Service
Queues
L1 Store Queue
(LSQ)
L2 Prefetch (3)
Address Bus Data Bus
Castout
Queue (9) /
Push
Queue (10)2
Bus Store Queue
Load
Queue (11)
Completion Queue
Reservation
Station
Reservation
Station
Reservation
Station
Reservation
Station
Branch Processing Unit
BTIC (128-Entry)
BHT (2048-Entry)
VR Issue
(4-Entry/2-Issue)
GPR Issue
(6-Entry/3-Issue)
FPR Issue
(2-Entry/1-Issue)
Fetcher
Dispatch
Unit
Instruction MMU
IBAT Array
Data MMU
DBAT Array
128-Bit (4 Instructions)
Tags 32-Kbyte
I Cache
32-Kbyte
D Cache
Tags
SRs
(Original)
128-Entry
DTLB
Reservation
Stations (2-Entry)
Vector
Touch
Queue
Completed
Stores
512-Kbyte Unified L2 Cache Controller
Line
Tags Block 0 (32-Byte)
System Bus Interface
Notes: The castout queue and push queue share resources such for a combined total of entries.
The castout queue itself is limited to 9 entries, ensuring 1 entry will be available for a push.
Integer
Unit 2
Reservation
Stations (2)
Reservation
Station
Integer
Unit 1
(3)
+
3
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
2. Features
This section summarizes features of the PC7447A implementation of the PowerPC architecture.
Major features of the PC7447A are as follows:
High-performance, superscalar microprocessor
Up to four instructions can be fetched from the instruction cache at a time
Up to 12 instructions can be in the instruction queue (IQ)
Up to 16 instructions can be at some stage of execution simultaneously
Single-cycle execution for most instructions
One instruction per clock cycle throughput for most instructions
Seven-stage pipeline control
Eleven independent execution units and three register files
Branch processing unit (BPU) features static and dynamic branch prediction
128-entry (32-set, four-way set-associative) branch target instruction cache (BTIC), a cache
of branch instructions that have been encountered in branch/loop code sequences. If a
target instruction is in the BTIC, it is fetched into the instruction queue a cycle sooner than it
can be made available from the instruction cache. Typically, a fetch that hits the BTIC
provides the first four instructions in the target stream.
2048-entry branch history table (BHT) with two bits per entry for four levels of prediction: not
taken, strongly not taken, taken, and strongly taken
Up to three outstanding speculative branches
Branch instructions that do not update the count register (CTR) or link register (LR) are often
removed from the instruction stream
Eight-entry link register stack to predict the target address of Branch Conditional to Link
Register (BCLR) instructions
Four integer units (IUs) that share 32 GPRs for integer operands
Three identical IUs (IU1a, IU1b, and IU1c) can execute all integer instructions except
multiply, divide, and move to/from special-purpose register instructions.
IU2 executes miscellaneous instructions including the CR logical operations, integer
multiplication and division instructions, and move to/from special-purpose register
instructions.
Five-stage FPU and a 32-entry FPR file
Fully IEEE® 754-1985-compliant FPU for both single- and double-precision operations
Supports non-IEEE mode for time-critical operations
Hardware support for denormalized number
4
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
Thirty-two 64-bit FPRs for single- or double-precision operands
Four vector units and 32-entry vector register file (VRs)
Vector permute unit (VPU)
Vector integer unit 1 (VIU1) handles short-latency AltiVec™ integer instructions, such as
vector add instructions (for example, vaddsbs, vaddshs, and vaddsws).
Vector integer unit 2 (VIU2) handles longer-latency AltiVec integer instructions, such as
vector multiply add instructions (for example, vmhaddshs, vmhraddshs, and vmladduhm).
Vector floating-point unit (VFPU)
Three-stage load/store unit (LSU)
Supports integer, floating-point, and vector instruction load/store traffic
Four-entry vector touch queue (VTQ) supports all four architectures of the AltiVec data
stream operations
Three-cycle GPR and AltiVec load latency (byte, half word, word, vector) with one-cycle
throughput
Four-cycle FPR load latency (single, double) with one-cycle throughput
No additional delay for misaligned access within double-word boundary
Dedicated adder calculates effective addresses (EAs)
Supports store gathering
Performs alignment, normalization, and precision conversion for floating-point data
Executes cache control and TLB instructions
Performs alignment, zero padding, and sign extension for integer data
Supports hits under misses (multiple outstanding misses)
Supports both big- and little-endian modes, including misaligned little-endian accesses
Three issue queues, FIQ, VIQ, and GIQ, can accept as many as one, two, and three instructions,
respectively, in a cycle. Instruction dispatch requires the following:
Instructions can only be dispatched from the three lowest IQ entries: IQ0, IQ1, and IQ2
A maximum of three instructions can be dispatched to the issue queues per clock cycle
Space must be available in the CQ for an instruction to dispatch (this includes instructions
that are assigned a space in the CQ but not in an issue queue)
5
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Rename buffers
16 GPR rename buffers
16 FPR rename buffers
16 VR rename buffers
Dispatch unit
Decode/dispatch stage fully decodes each instruction
Completion unit
The completion unit retires an instruction from the 16-entry completion queue (CQ) when all
instructions ahead of it have been completed, the instruction has finished execution, and no
exceptions are pending
Guarantees sequential programming model (precise exception model)
Monitors all dispatched instructions and retires them in order
Tracks unresolved branches and flushes instructions after a mispredicted branch
Retires as many as three instructions per clock cycle
Separate on-chip L1 instruction and data caches (Harvard Architecture)
32-Kbyte, eight-way set-associative instruction and data caches
Pseudo least-recently-used (PLRU) replacement algorithm
32-byte (eight-word) L1 cache block
Physically indexed/physical tags
Cache write-back or write-through operation programmable on a per-page or per-block basis
Instruction cache can provide four instructions per clock cycle; data cache can provide four
words per clock cycle
Caches can be disabled in software
Caches can be locked in software
MESI data cache coherency maintained in hardware
Separate copy of data cache tags for efficient snooping
Parity support on cache and tags
No snooping of instruction cache except for icbi instruction
Data cache supports AltiVec LRU and transient instructions
Critical double- and/or quad-word forwarding is performed as needed. Critical quad-word
forwarding is used for AltiVec loads and instruction fetches. Other accesses use critical
double-word forwarding.
Level 2 (L2) cache interface
On-chip, 512-Kbyte, eight-way set-associative unified instruction and data cache
Fully pipelined to provide 32 bytes per clock cycle to the L1 caches
A total nine-cycle load latency for an L1 data cache miss that hits in L2
Cache write-back or write-through operation programmable on a per-page or per-block basis
64-byte, two-sectored line size
Parity support on cache
Separate memory management units (MMUs) for instructions and data
52-bit virtual address, 32- or 36-bit physical address
6
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
Address translation for 4-Kbyte pages, variable-sized blocks, and 256-Mbyte segments
Memory programmable as write-back/write-through, caching-inhibited/caching-allowed, and
memory coherency enforced/memory coherency not enforced on a page or block basis
Separate IBATs and DBATs (eight each) also defined as SPRs
Separate instruction and data translation look aside buffers (TLBs)
Both TLBs are 128-entry, two-way set-associative, and use a LRU replacement algorithm
TLBs are hardware- or software-reloadable (that is, a page table search is performed in
hardware or by system software on a TLB miss).
Efficient data flow
Although the VR/LSU interface is 128 bits, the L1/L2 bus interface allows up to 256 bits
The L1 data cache is fully pipelined to provide 128 bits/cycle to or from the VRs
L2 cache is fully pipelined to provide 256 bits per processor clock cycle to the L1 cache
As many as eight outstanding, out-of-order, cache misses are allowed between the L1 data
cache and the L2 bus
As many as 16 out-of-order transactions can be present on the MPX bus
Store merging for multiple store misses to the same line. Only coherency action taken
(address-only) for store misses merged to all 32 bytes of a cache block (no data tenure
needed)
Three-entry finished store queue and five-entry completed store queue between the LSU
and the L1 data cache
Separate additional queues for efficient buffering of outbound data (such as castouts and
write-through stores) from the L1 data cache and L2 cache
Multiprocessing support features include the following:
Hardware-enforced, MESI cache coherency protocols for data cache
Load/store with reservation instruction pair for atomic memory references, semaphores, and
other multiprocessor operations
Power and thermal management
A new dynamic frequency switching (DFS) feature allows the processor core frequency to be
halved through software to reduce power consumption
The following three power-saving modes are available to the system:
Nap: Instruction fetching is halted. Only the clocks for the time base, decrementer, and JTAG
logic remain running. The part goes into the doze state to snoop memory operations on the
bus and then back to nap using a QREQ/QACK processor-system handshake protocol.
Sleep: Power consumption is further reduced by disabling bus snooping, leaving only the
PLL in a locked and running state. All internal functional units are disabled.
Deep sleep: When the part is in the deep Sleep state, the system can disable the PLL. The
system can then disable the SYSCLK source for greater system power savings. Power-on
reset procedures for restarting and relocking the PLL must be followed upon exiting the deep
sleep state.
7
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Instruction cache throttling provides control of instruction fetching to limit device temperature
A new temperature diode that can determine the temperature of the microprocessor
Performance monitor can be used to help debug system designs and improve software efficiency
In-system testability and debugging features through JTAG boundary-scan capability
Testability
LSSD scan design
IEEE 1149.1 JTAG interface
Array built-in self test (ABIST), factory test only
Reliability and serviceability
Parity checking on system bus
Parity checking on the L1 and L2 caches
3. General Parameters
Table 3-1 provides a summary of the general parameters of the PC7447A.
Table 3-1. Device Parameters
Parameter Description
Technology 0.13 µm CMOS, nine-layer metal
Die size 8.51 mm × 9.86 mm
Transistor count 48.6 million
Logic design Fully-static
Packages Surface mount 360 ceramic ball grid array
(HITCE)
Core power supply 1.3V ± 50 mV and 1.1V ± 50 mV DC nominal
I/O power supply 1.8V ± 5% DC, or 2.5V ±5% DC
8
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
4. Signal Description
Figure 4-1. PC7447A Microprocessor Signal Groups
Note: For the PC7447A, there are 5 PLL_CFG signals, (PLL_CFG[0:4]
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
4
1
1
1
1
1
1
1
1
PC7447A
INT
SMI
MCP
SRESET
HRESET
CKSTP_IN
CKSTP_OUT
TBEN
QREQ
QACK
BVSEL
BMODE[0:1]
PMON_IN
PMON_OUT
SYSCLK
PLL_CFG[0:3](2)
PLL_EXT
EXT_QUAL
CLK_OUT
TCK
TDI
TDO
TMS
TRST
BR
BG
A[0:35]
AP[0:4]
TS
TT[0:4]
TBST
TSIZ[0:2]
GBL
WT
CI
AACK
ARTRY
SHD0/SHD1
HIT
DBG
DTI[0:3]
DRDY
D[0:63]
DP[0:7]
TA
TEA
1
1
36
5
1
5
1
3
1
1
1
1
1
2
1
1
4
1
64
8
1
1
Address
Arbitration
Address
Transfer
Address
Transfer
Attributes
Address
Transfer
Termination
Data
Arbitration
Data
Transfer
Data
Transfer
Termination
Interrupts/Resets
Processor
Status/Control
Clock Control
Test Interface
(JTAG)
AVDD
GND
VDD
OVDD
9
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
5. Detailed Specification
This specification describes the specific requirements for the microprocessor PC7447A in compliance
with e2v standard screening.
6. Applicable Documents
1. MIL-STD-883: Test methods and procedures for electronics
2. MIL-PRF-38535: Appendix A: General specifications for microcircuits
The microcircuits are in accordance with the applicable documents and as specified herein.
6.1 Design and Construction
6.1.1 Terminal Connections
Depending on the package, the terminal connections are as shown in Table 8-1, Table 6-2 and Figure 4-
1.
6.2 Absolute Maximum Ratings
The tables in this section describe the PC7447A DC electrical characteristics. Table 6-1 provides the
absolute maximum ratings.
Notes: 1. Functional and tested operating conditions are given in Table 6-2 on page 10. Absolute maximum ratings are stress ratings
only, and functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability
or cause permanent damage to the device.
2. Caution: VDD/AVDD must not exceed OVDD by more than 1V during normal operation; this limit may be exceeded for a maxi-
mum of 20 ms during the power-on reset and power-down sequences.
3. Caution: OVDD must not exceed VDD/AVDD by more than 2V during normal operation; this limit may be exceeded for a maxi-
mum of 20 ms during the power-on reset and power-down sequences.
4. BVSEL must be set to 0, such that the bus is in 1.8V mode.
5. BVSEL must be set to HRESET or 1, such that the bus is in 2.5V mode.
6. Caution: VIN must not exceed OVDD by more than 0.3V at any time including during power-on reset.
7. VIN may overshoot/undershoot to a voltage and for a maximum duration shown in Figure 6-1 on page 10.
Table 6-1. Absolute Maximum Ratings(1)
Symbol Characteristic Maximum Value Unit
VDD(2) Core supply voltage -0.3 to 1.60 V
AVDD(2) PLL supply voltage -0.3 to 1.60 V
OVDD(3)(4)
Processor bus supply voltage BVSEL = 0 -0.3 to 1.95 V
OVDD(3)(5) BVSEL = HRESET or OVDD -0.3 to 2.7 V
VIN(6)(7)
Input voltage Processor bus -0.3 to OVDD + 0.3 V
VIN JTAG signals -0.3 to OVDD + 0.3 V
TSTG Storage temperature range -55 to 150 °C
10
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
6.3 Recommended Operating Conditions
Table 6-2 provides the recommended operating conditions for the PC7447A.
Notes: 1. These are the recommended and tested operating conditions. Proper device operation outside of these conditions is not
guaranteed.
2. This voltage is the input to the filter discussed in Section “PLL Power Supply Filtering” on page 41 and not necessarily the
voltage at the AVDD pin, which may be reduced from VDD by the filter.
Figure 6-1. Overshoot/Undershoot Voltage
The PC7447A provides several I/O voltages to support both compatibility with existing systems and
migration to future systems. The PC7447A core voltage must always be provided at a nominal 1.3V (see
Table 6-2 on page 10 for the actual recommended core voltage). The input voltage threshold for each
bus is selected by sampling the state of the voltage select pins at the negation of the signal HRESET.
The output voltage will swing from GND to the maximum voltage applied to the OVDD power pins. Table
6-3 on page 11 provides the input threshold voltage settings. Because these settings may change in
future products, it is recommended that BVSEL be configured using resistor options, jumpers, or some
other flexible means, with the capability to reconfigure the termination of this signal in the future if
necessary.
Table 6-2. Recommended Operating Conditions(1)
Symbol Characteristic
Recommended Value
UnitMin Max
VDD Core supply voltage 1.3V ± 50 mV or 1.1V ± 50 mV V
AVDD(2) PLL supply voltage 1.3V ± 50 mV or 1.1V ± 50 mV V
OVDD Processor bus supply
voltage
BVSEL = 0 1.8V ± 5%
V
OVDD BVSEL = HRESET or
OVDD 2.5V ± 5%
VIN Input voltage Processor bus GND OVDD V
VIN JTAG signals GND OVDD
TJDie-junction temperature -55 125°C °C
GND
GND – 0.3V
GND – 0.7V
Not to exceed 10% of tSYSCLK
OVDD + 20%
OVDD + 5%
OVDD
VIH
VIL
11
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Notes: 1. Caution: The input threshold selection must agree with the OVDD voltages supplied. See notes in Table 6-1 on page 9.
2. If used, pull-down resistors should be less than 250.
6.4 Thermal Characteristics
6.4.1 Package Characteristics
Notes: 1. See “Thermal Management Information” on page 12 for details about thermal management.
2. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) tempera-
ture, ambient temperature, airflow, power dissipation of other components on the board, and board thermal resistance.
3. Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board horizontal.
4. Per JEDEC JESD51-6 with the board horizontal.
5. Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
6. This is the thermal resistance between the die and the case top surface as measured with the cold plate method (MIL
SPEC-883 Method 1012.1) with the calculated case temperature. The actual value of RθJC for the part is less than 0.1°C/W.
6.4.2 Internal Package Conduction Resistance
For the exposed-die packaging technology described in Table 6-4 on page 11, the intrinsic conduction
thermal resistance paths are as follows:
The die junction-to-case thermal resistance (the case is actually the top of the exposed silicon die)
The die junction-to-ball thermal resistance
Figure 9-2 depicts the primary heat transfer path for a package with an attached heat sink mounted to a
printed-circuit board.
Table 6-3. Input Threshold Voltage Setting(1)
BVSEL Signal Processor Bus Input Threshold is Relative to: Notes
01.8V(2)
¬HRESET Not available
HRESET 2.5V
12.5V
Table 6-4. Package Thermal Characteristics(1)
Symbol Characteristic Value Unit
RθJA(2)(3) Junction-to-ambient thermal resistance, natural convection, single-layer (1s) board 26 °C/W
RθJMA(2)(4) Junction-to-ambient thermal resistance, natural convection, four-layer (2s2p) board 19 °C/W
RθJMA(2)(4) Junction-to-ambient thermal resistance, 200 ft./min. airflow, single-layer (1s) board 20 °C/W
RθJMA(2)(4) Junction-to-ambient thermal resistance, 200 ft./min. airflow, four-layer (2s2p) board 16 °C/W
RθJB(5) Junction-to-board thermal resistance 10 °C/W
RθJC(6) Junction-to-case thermal resistance < 0.1 °C/W
12
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
Figure 6-2. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
Note the internal versus external package resistance.
Heat generated on the active side of the chip is conducted through the silicon, through the heat sink
attach material (or thermal interface material), and finally to the heat sink where it is removed by forced-
air convection.
Because the silicon thermal resistance is quite small, the temperature drop in the silicon may be
neglected for a first-order analysis. Thus, the thermal interface material and the heat sink conduc-
tion/convective thermal resistances are the dominant terms.
6.4.3 Thermal Management Information
This section provides thermal management information for the high coefficient of the thermal expansion
ceramic ball grid array (HITCE) package for air-cooled applications. Proper thermal control design is pri-
marily dependent on the system-level design – the heat sink, airflow, and thermal interface material. The
PC7447A implements several features designed to assist with thermal management, including DFS and
the temperature diode. DFS reduces the power consumption of the device by reducing the core fre-
quency; see Table 6-6 on page 19 for specific information regarding power reduction and DFS. The
temperature diode allows an external device to monitor the die temperature in order to detect excessive
temperature conditions and alert the system; see section “Temperature Diode” on page 16 for more
information.
To reduce the die-junction temperature, heat sinks may be attached to the package by several methods
– spring clips to holes in the printed-circuit board or package, and mounting clips and screw assembly
(see Figure 6-3); however, due to the potentially large mass of the heat sink, attachment through the
printed-circuit board is suggested. If a spring clip is used, the spring force should not exceed ten pounds.
External Resistance
External Resistance
Internal Resistance
Radiation Convection
Heat Sink
Thermal Interface Material
Die/Package
Die Junction
Package/Leads
Printed-Circuit Board
Radiation Convection
13
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Figure 6-3. Package Exploded Cross-sectional View with Several Heat Sink Options
6.4.4 Thermal Interface Materials
A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the
thermal contact resistance. For those applications where the heat sink is attached by spring clip mecha-
nism, Figure 6-4 on page 14 shows the thermal performance of three thin-sheet thermal-interface
materials (silicone, graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function
of contact pressure.
As shown, the performance of these thermal interface materials improves with increasing contact
pressure.
The use of thermal grease significantly reduces the interface thermal resistance. That is, the bare joint
results in a thermal resistance approximately seven times greater than the thermal grease joint.
Often, heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit
board (see Figure 6-3 on page 13). Therefore, synthetic grease offers the best thermal performance,
considering the low interface pressure, and is recommended due to the high power dissipation of the
PC7447A. Of course, the selection of any thermal interface material depends on many factors – thermal
performance requirements, manufacturability, service temperature, dielectric properties, cost, and so on.
Printed-Circuit Board
Thermal Interface
Material
Heat Sink
Clip
Heat Sink HCTE Package
14
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
Figure 6-4. Thermal Performance of Select Thermal Interface Material
6.4.4.1 Heat Sink Selection Example
For preliminary heat sink sizing, the die-junction temperature can be expressed as follows:
TJ = TI + Tr + (RθJC + Rθint + Rθsa) × Pd
where:
TJ is the die-junction temperature
Ti is the inlet cabinet ambient temperature
Tr is the air temperature rise within the computer cabinet
RθJC is the junction-to-case thermal resistance
Rθint is the adhesive or interface material thermal resistance
Rθsa is the heat sink base-to-ambient thermal resistance
Pd is the power dissipated by the device
During operation, the die-junction temperatures (TJ) should be maintained less than the value specified
in Table 6-2 on page 10. The temperature of air cooling the component greatly depends on the ambient
inlet air temperature and the air temperature rise within the electronic cabinet. An electronic cabinet inlet-
air temperature (Ti) may range from 30° to 40°C. The air temperature rise within a cabinet (Tr) may be in
the range of 5° to 10°C. The thermal resistance of the thermal interface material (Rθint) is typically about
1.5°C/W. For example, assuming a Ti of 30°C, a Tr of 5°C, an HITCE package RθJC = 0.1, and a typical
power consumption (Pd) of 18.7W, the following expression for TJ is obtained:
Die-junction temperature: TJ = 30°C + 5°C + (0.1°C/W + 1.5°C/W + θsa) × 18.7W
0
0.5
1
1.5
2
010 20304050607080
Silicone Sheet (0.006 in.)
Bare Joint
Floroether Oil Sheet (0.007 in.)
Graphite/Oil Sheet (0.005 in.)
Synthetic Grease
Contact Pressure (psi)
Specific Thermal Resistance (K-in.2/W)
15
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
For this example, a Rθsa value of 2.1°C/W or less is required to maintain the die junction temperature
below the maximum value of Table 6-2 on page 10.
Though the die junction-to-ambient and the heat sink-to-ambient thermal resistances are a common fig-
ure-of-merit used for comparing the thermal performance of various microelectronic packaging
technologies, one should exercise caution when only using this metric in determining thermal manage-
ment because no single parameter can adequately describe three-dimensional heat flow. The final die-
junction operating temperature is not only a function of the component-level thermal resistance, but the
system-level design and its operating conditions. In addition to the component's power consumption, a
number of factors affect the final operating die-junction temperature – airflow, board population (local
heat flux of adjacent components), heat sink efficiency, heat sink attach, heat sink placement, next-level
interconnect technology, system air temperature rise, altitude, and so on.
Due to the complexity and variety of system-level boundary conditions for today's microelectronic equip-
ment, the combined effects of the heat transfer mechanisms (radiation, convection, and conduction) may
vary widely. For these reasons, we recommend using conjugate heat transfer models for the board, as
well as system-level designs.
For system thermal modeling, the PC7447A thermal model is shown in Figure 6-5 on page 16. Four vol-
umes represent this device. Two of the volumes, solder ball-air and substrate, are modeled using the
package outline size of the package. The other two, die, and bump-underfill, have the same size as the
die. The silicon die should be modeled 9.5 × 9.5 × 0.7 mm with the heat source applied as a uniform
source at the bottom of the volume. The bump and underfill layer is modeled as 7.3 × 9.3 × 0.7 mm (or
as a collapsed volume) with orthotropic material properties: 0.6 W/(m × K) in the xy-plane and 1.9 W/(m
× K) in the direction of the z-axis. The substrate volume is 25 × 25 × 1.2 mm, and has 8.1 W/(m × K) iso-
tropic conductivity in the xy-plane and 4 W/(m × K) in the direction of the z-axis. The solder ball and air
layer are modeled with the same horizontal dimensions as the substrate and are 0.6 mm thick. They can
also be modeled as a collapsed volume using orthotropic material properties: 0.034 W/(m × K) in the xy-
plane direction and 3.8 W/(m × K) in the direction of the z-axis.
16
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
Figure 6-5. Recommended Thermal Model of PC7447A
6.4.4.2 Temperature Diode
The PC7447A has a temperature diode on the microprocessor that can be used in conjunction with other
system temperature monitoring devices. These devices use the negative temperature coefficient of a
diode operated at a constant current to determine the temperature of the microprocessor and its environ-
ment. For proper operation, the monitoring device used should auto-calibrate the device by canceling out
the VBE variation of each PC7447A’s internal diode.
The following are the specifications of the PC7447A on-board temperature diode:
Vf > 0.40V
Vf < 0.90V
Operating range 2 - 300 µA
Diode leakage < 10 nA at 125°C
Ideality factor over 5 µA – 150 µA at 60°C: 1 <= n <= TBD
Ideality factor is defined as the deviation from the ideal diode equation:
Another useful equation is:
Bump and Underfill
Die
Substrate
Solder and Air
Die
Substrate
Side View of Model (Not to Scale)
Side View of Model (Not to Scale)
x
y
z
Conductivity Value Unit
Bump and Underfill (7.3 x 9.3 x 0.070 mm)
W/(m x K)
Substrate (25 x 25 x 1.2 mm)
Solder Ball and Air (25 x 25 x 0.6 mm)
kx0.6
ky0.6
kz1.9
kx8.1
ky8.1
kz4.0
kx
ky
kz
0.034
0.034
3.8
IfW Ise
qVf
nKT
-----------
1=
VHVL
nKT
q
------- InIH
IL
-----
=
17
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Where:
Ifw = Forward current
Is = Saturation current
Vd = Voltage at diode
Vf = Voltage forward biased
VH = Diode voltage while IH is flowing
VL = Diode voltage while IL is flowing
IH = Larger diode bias current
IL = Smaller diode bias current
q = Charge of electron (1.6 × 10-19 C)
n = Ideality factor (normally 1.0)
K = Boltzman’s constant (1.38 × 10-23 Joules/K)
T = Temperature (Kelvins)
The ratio of IH to IL is usually selected to be 10:1. The above simplifies to the following:
VH - VL = 1.986 × 10-4 × nT
Solving for T, the equation becomes:
6.4.4.3 Dynamic Frequency Switching (DFS)
The new DFS feature in the PC7447A adds the ability to divide the processor-to-system bus ratio by two
during normal functional operation by setting the HID1[DFS1] bit. The frequency change occurs in 1
clock cycle, and no idle waiting period is required to switch between modes. Additional information
regarding DFS can be found in the MPC7450 RISC Microprocessor Family User’s Manual.
6.4.4.4 Power Consumption with DFS Enabled
Power consumption with DFS enabled can be approximated using the following formula:
Where:
PDFS = Power consumption with DFS enabled
fDFS = Core frequency with DFS enabled
f = Core frequency prior to enabling DFS
P = Power consumption prior to enabling DFS (see Table 6-6 on page 19)
PDS = Deep sleep mode power consumption (see Table 6-6 on page 19)
The above is an approximation only. Power consumption with DFS enabled is not tested or guaranteed.
nT VHVL
1 986 10 4
×,
---------------------------------=
PDFS fDFS
f
-----------PP
DS
()
PDS
+=
18
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
6.4.4.5 Bus-to-Core Multiplier Constraints with DFS
DFS is not available for all bus-to-core multipliers as configured by PLL_CFG[0:4] during hard reset.
Specifically, because the PC7447A does not support quarter clock ratios or the 1x multiplier, the DFS
feature is limited to integer PLL multipliers of 4x and higher. The complete listing is shown in Table 6-5
on page 18.
Table 6-5. Valid Divide Ratio Configurations
Bus-to-Core Multiplier Configured by
PLL_CFG[0:4] (see Table 12-1 on page 39)
Bus-to-Core Multiplier with
HID1[DFS1] = 1 (÷2)
2x N/A
3x N/A
4x 2x
5x 2.5x
5.5x 2x
6x 3x
6.5x N/A
7x 3.5x
7.5x N/A
8x 4x
8.5x N/A
9x 4.5x
9.5x N/A
10x 5x
10.5x N/A
11x 5.5x
11.5x N/A
12x 6x
12.5x N/A
13x 6.5x
13.5x N/A
14x 7x
15x 7.5x
16x 8x
17x 8.5x
18x 9x
20x 10x
21x 10.5x
24x 12x
28x 14x
19
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
6.4.4.6 Minimum Core Frequency Requirements with DFS
In many systems, enabling DFS can result in very low processor core frequencies. However, care must
be taken to ensure that the resulting processor core frequency is within the limits specified in Table 9-2
on page 25. Proper operation of the device is not guaranteed at core frequencies below the specified
minimum fcore.
6.4.5 Power Consumption
Table 6-6 provides the power consumption for the PC7447A. For information regarding power consump-
tion when dynamic frequency switching is enabled, See “Dynamic Frequency Switching (DFS)” on page
17.
Notes: 1. These values apply for all valid processor buses. The values do not include I/O supply power (OVDD) or PLL supply power
(AVDD). OVDD powe r is system depen dent but is typically < 5% of VDD power. Worst case power consumption for AVDD <
3mW.
2. Typical power is an average value measured at the nominal recommended VDD (see Table 6-2 on page 10) and 65°C while
running the Dhrystone 2.1 benchmark and achieving 2.3 Dhrystone MIPs/MHz
3. Maximum power is the average measured at nominal VDD and maximum operating junction temperature (see Table 6-2 on
page 10) while running an entirely cache-resident, contrived sequence of instructions which keep all the execution units
maximally busy.
4. Doze mode is not a user-definable state; it is an intermediate state between full-power and either nap or sleep mode. As a
result, power consumption for this mode is not tested.
5. Power consumption for these devices is artificially constrained during screening to assure lower power consumption than
other speed grades.
Table 6-6. Power Consumption for PC7447A
Processor (CPU) Frequency
1000 1167 1267 1333(5) 1420 Unit
Full-Power Mode
Core Power Supply 1.1 1.1 1.3 1.3 1.3
Typical(1)(2) 8 9.2 18.3 18 21 W
Maximum(1)(3) 11.5 13 26 25 30 W
Nap Mode
Typical(1)(2) 1.3 1.3 4.1 3.3 4.1 W
Sleep Mode
Typical(1)(2) 1.3 1.3 4.1 3.3 4.1 W
Deep Sleep Mode (PLL Disabled)
Typical(1)(2) 1.2 1.2 4 3.2 4 W
20
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
7. Pin Assignment
Figure 7-1 shows the pinout of the PC7447A, 360 high coefficient of the thermal expansion ceramic ball
grid array (HITCE) package as viewed from the top surface. Figure 7-2 shows the side profile of the
HITCE package to indicate the direction of the top surface view.
Figure 7-1. Pinout of the PC7447A, 360 HITCE Package as Viewed from the Top Surface
Figure 7-2. Side View of the CBGA Package
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
321456 1617 18 19
U
V
W
151413121110987
Substrate Assembly
Encapsulant
View Die
21
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
8. Pinout Listings
Table 8-1 provides the pinout listing for the PC7447A, 360 HITCE package. The pinouts of the PC7447A
and PC7447 are pin compatible but there have been some changes. A PC7447A may be populated on a
board designed for a PC7447 provided all pins defined as ‘Not Connected’ for the PC7447 are untermi-
nated as required by the PC7457 RISC Microprocessor Specification. The PC7447A uses pins
previously marked ‘Not Connected’ for the temperature diode pins and for additional power and ground
connections. Because these ‘Not Connected’ pins in the PC7447 360 pin package are not driven in func-
tional mode, a PC7447 can be populated in a PC7447A board. See section “Connection
Recommendations” on page 41 for additional information.
Note: This pinout is not compatible with the PC750, PC7400, or PC7410 360 BGA package.
Table 8-1. Pinout Listing for the PC7447A, 360 HITCE Package
Signal Name Pin Number Active I/O I/F Select(1)
A[0:35](2) E11, H1, C11, G3, F10, L2, D11, D1, C10, G2, D12, L3, G4, T2, F4, V1,
J4, R2, K5, W2, J2, K4, N4, J3, M5, P5, N3, T1, V2, U1, N5, W1, B12,
C4, G10, B11
High I/O BVSEL
AACK R1 Low Input BVSEL
AP[0:4](2) C1, E3, H6, F5, G7 High I/O BVSEL
ARTRY(3) N2 Low I/O BVSEL
AVDD A8 Input BVSEL
BG M1 Low Input BVSEL
BMODE0(4) G9 Low Input BVSEL
BMODE1(5) F8 Low Input BVSEL
BR D2 Low Output BVSEL
BVSEL(1)(6) B7 High Input BVSEL
CI(3) J1 Low Output BVSEL
CKSTP_IN A3 Low Input BVSEL
CKSTP_OUT B1 Low Output BVSEL
CLK_OUT H2 High Output BVSEL
D[0:63]
R15, W15, T14, V16, W16, T15, U15, P14, V13, W13, T13, P13, U14,
W14, R12, T12, W12, V12, N11, N10, R11, U11, W11, T11, R10, N9,
P10, U10, R9, W10, U9, V9, W5, U6, T5, U5, W7, R6, P7, V6, P17,
R19, V18, R18, V19, T19, U19, W19, U18, W17, W18, T16, T18, T17,
W3, V17, U4, U8, U7, R7, P6, R8, W8, T8
High I/O BVSEL
DBG M2 Low Input BVSEL
DP[0:7] T3, W4, T4, W9, M6, V3, N8, W6 High I/O BVSEL
DRDY(7) R3 Low Output BVSEL
DTI[0:3](8) G1, K1, P1, N1 High Input BVSEL
EXT_QUAL(9) A11 High Input BVSEL
GBL E2 Low I/O BVSEL
22
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
GND
B5, C3, D6, D13, E17, F3, G17, H4, H7, H9, H11, H13, J6, J8, J10,
J12, K7, K3, K9, K11, K13, L6, L8, L10, L12, M4, M7, M9, M11, M13,
N7, P3, P9, P12, R5, R14, R17, T7, T10, U3, U13, U17, V5, V8, V11,
V15
–– N/A
GND(15) A17, A19, B13, B16, B18, E12, E19, F13, F16, F18, G19, H18, J14,
L14, M15, M17, M19, N14, N16, P15, P19 –– N/A
GND_SENSE(19) G12, N13 N/A
HIT(7) B2 Low Output BVSEL
HRESET D8 Low Input BVSEL
INT D4 Low Input BVSEL
L1_TSTCLK(9) G8 High Input BVSEL
L2_TSTCLK(10) B3 High Input BVSEL
No Connect(11) A6, A14, A15, B14, B15, C14, C15, C16, C17, C18, C19, D14, D15,
D16, D17, D18, D19, E14, E15, F14, F15, G14, G15, H15, H16, J15,
J16, J17, J18, J19, K15, K16, K17, K18, K19, L15, L16, L17, L18, L19
––
LSSD_MODE(6)(12) E8 Low Input BVSEL
MCP C9 Low Input BVSEL
OVDD B4, C2, C12, D5, F2, H3, J5, K2, L5, M3, N6, P2, P8, P11, R4, R13,
R16, T6, T9, U2, U12, U16, V4, V7, V10, V14 –– N/A
OVDD_SENSE(16) E18, G18 N/A
PLL_CFG[0:4] B8, C8, C7, D7, A7 High Input BVSEL
PMON_IN(13) D9 Low Input BVSEL
PMON_OUT A9 Low Output BVSEL
QACK G5 Low Input BVSEL
QREQ P4 Low Output BVSEL
SHD[0:1](3) E4, H5 Low I/O BVSEL
SMI F9 Low Input BVSEL
SRESET A2 Low Input BVSEL
SYSCLK A10 Input BVSEL
TA K6 Low Input BVSEL
TBEN E1 High Input BVSEL
TBST F11 Low Output BVSEL
TCK C6 High Input BVSEL
TDI(6) B9 High Input BVSEL
TDO A4 High Output BVSEL
TEA L1 Low Input BVSEL
TEMP_ANODE(17) N18
TEMP_CATHODE(17) N19
Table 8-1. Pinout Listing for the PC7447A, 360 HITCE Package (Continued)
Signal Name Pin Number Active I/O I/F Select(1)
23
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Notes: 1. OVDD supplies power to the processor bus, JTAG, and all control signals; VDD supplies power to the processor core and the
PLL (after filtering to become AVDD). To program the I/O voltage, connect BVSEL to either GND (selects 1.8V), or to
HRESET or OVDD (selects 2.5V); see Table 6-3 on page 11. If used, the pull-down resistor should be less than 250.
Because these settings may change in future products, it is recommended BVSEL be configured using resistor options,
jumpers, or some other flexible means, with the capability to reconfigure the termination of this signal in the future if neces-
sary. For actual recommended value of VIN or supply voltages see Table 6-2 on page 10.
2. Unused address pins must be pulled down to GND and corresponding address parity pins pulled up to OVDD.
3. These pins require weak pull-up resistors (for example, 4.7 K) to maintain the control signals in the negated state after they
have been actively negated and released by the PC7447A and other bus masters.
4. This signal selects between MPX bus mode (asserted) and 60x bus mode (negated) and will be sampled at HRESET going
high.
5. This signal must be negated during reset, by pull-up resistor to OVDD or negation by ¬HRESET (inverse of HRESET), to
ensure proper operation.
6. Internal pull up on die.
7. Ignored in 60x bus mode.
8. These signals must be pulled down to GND if unused, or if the PC7447A is in 60x bus mode.
9. These input signals are for factory use only and must be pulled down to GND for normal machine operation.
10. This test signal is recommended to be tied to HRESET; however, other configurations will not adversely affect performance.
11. These signals are for factory use only and must be left unconnected for normal machine operation. Some pins that were
NCs on the PC7447, have now been defined for other purposes.
12. These input signals are for factory use only and must be pulled up to OVDD for normal machine operation.
13. This pin can externally cause a performance monitor event. Counting of the event is enabled through software.
14. This signal must be asserted during reset, by pull down to GND or assertion by HRESET, to ensure proper operation.
15. These pins were NCs on the PC7447. They may be left unconnected for backward compatibility with these devices, but it is
recommended they be connected in new designs to facilitate future products. See section “Connection Recommendations”
on page 41 for more information.
16. These pins were OVDD pins on the PC7447. These pins are internally connected to OVDD and are intended to allow an exter-
nal device to detect the I/O voltage level present inside the device package. If unused, they must be connected directly to
OVDD or left unconnected.
17. These pins provide connectivity to the on-chip temperature diode that can be used to determine the die junction temperature
of the processor. These pins may be left unterminated if unused.
TEST[0:3](12) A12, B6, B10, E10 Input BVSEL
TEST[4](9) D10 Input BVSEL
TMS(6) F1 High Input BVSEL
TRST(6)(14) A5 Low Input BVSEL
TS(3) L4 Low I/O BVSEL
TSIZ[0:2] G6, F7, E7 High Output BVSEL
TT[0:4] E5, E6, F6, E9, C5 High I/O BVSEL
WT(3) D3 Low Output BVSEL
VDD H8, H10, H12, J7, J9, J11, J13, K8, K10, K12, K14, L7, L9, L11, L13,
M8, M10, M12 –– N/A
VDD(15) A13, A16, A18, B17, B19, C13, E13, E16, F12, F17, F19, G11, G16,
H14, H17, H19, M14, M16, M18, N15, N17, P16, P18 –– N/A
VDD_SENSE(18) G13, N12 N/A
Table 8-1. Pinout Listing for the PC7447A, 360 HITCE Package (Continued)
Signal Name Pin Number Active I/O I/F Select(1)
24
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
18. These pins are internally connected to VDD and are intended to allow an external device to detect the processor core voltage
level present inside the device package. If unused, they must be connected directly to VDD or left unconnected.
19. These pins are internally connected to GND and are intended to allow an external device to detect the processor ground
voltage level present inside the device package. If unused, they must be connected directly to GND or left unconnected.
Note: Caution must be exercised when performing boundary scan test operations on a board designed for a PC7447A but populated
with an PC7447. This is because in the PC7447 it is possible to drive the latches associated with the former ‘No Connect’ pins
in the PC7447, potentially causing contention on those pins. To prevent this, ensure that these pins are not connected on the
board or, if they are connected, ensure that the states of internal PC7447 latches do not cause these pins to be driven during
board testing.
9. Electrical Characteristics
9.1 Static Characteristics
Table 9-1 provides the DC electrical characteristics for the PC7447A.
Notes: 1. Nominal voltages; see Table 6-2 on page 10 for recommended operating conditions.
2. For processor bus signals, the reference is OVDD while GVDD is the reference for the L3 bus signals.
Table 9-1. DC Electrical Specifications (see Table 6-2 on page 10 for Recommended Operating Conditions)
Symbol Characteristic
Nominal Bus
Voltage(1) Min Max Unit Notes
VIH Input high voltage (all inputs) 1.8 OVDD × 0.65 OVDD + 0.3 V(2)
2.5 1.7 OVDD + 0.3
VIL Input low voltage (all inputs) 1.8 -0.3 OVDD × 0.35 V(2)(6)
2.5 -0.3 0.7
IIN
Input leakage current,
VIN = GVDD/ODD
VIN = GND
––30
-30
µA (2)(3)
ITSI
High-impedance (off-state) leakage current,
VIN = GVDD/ODD
VIN = GND
––30
-30
µA (2)(3)(4)
VOH Output high voltage at IOH = -5 mA 1.8 OVDD - 0.45 V
2.5 1.8
VOL Output low voltage at IOL = 5 mA 1.8 0.45 V
2.5 0.6
CIN
Capacitance,
VIN = 0V
f = 1 MHz
All other inputs 8 pF (5)
VIH Input high voltage (all inputs) 1.8 OVDD × 0.65 OVDD + 0.3 V(2)
2.5 1.7 OVDD + 0.3
VIL Input low voltage (all inputs) 1.8 -0.3 OVDD × 0.35 V(2)(6)
2.5 -0.3 0.7
IIN
Input leakge current,
VIN = GVDD/OVDD
VIN = GND
––30
-30
µA (2)(3)
25
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
3. Excludes test signals and IEEE 1149.1 boundary scan (JTAG) signals.
4. The leakage is measured for nominal OVDD/GVDD and VDD, or both OVDD/GVDD and VDD must vary in the same direction (for
example, both OVDD and VDD vary by either +5% or -5%).
5. Capacitance is periodically sampled rather than 100% tested.
6. Excludes signals with internal pull ups: BVSEL, LSSD_MODE, TDI, TMS, and TRST. Characterization of leakage current for
these signals is currently being conducted.
9.2 Dynamic Characteristics
This section provides the AC electrical characteristics for the PC7447A. After fabrication, functional parts
are sorted by maximum processor core frequency as shown in Section “Clock AC Specifications” on
page 25 and tested for conformance to the AC specifications for that frequency. The processor core fre-
quency is determined by the bus (SYSCLK) frequency and the settings of the PLL_CFG[0:4] signals,
and can be dynamically modified using dynamic frequency switching (DFS). Parts are sold by maximum
processor core frequency; See “Ordering Information” on page 46. for information on ordering parts.
DFS is described in Section “Dynamic Frequency Switching (DFS)” on page 17.
9.2.1 Clock AC Specifications
Table 9-2 provides the clock AC timing specifications as defined in Figure 9-1 on page 26 and repre-
sents the tested operating frequencies of the devices. The maximum system bus frequency, fSYSCLK,
given in Table 9-2 on page 25 is considered a practical maximum in a typical single-processor system.
The actual maximum SYSCLK frequency for any application of the PC7447A will be a function of the AC
timings of the PC7447A, the AC timings for the system controller, bus loading, printed-circuit board
topology, trace lengths, and so forth, and may be less than the value given in Table 9-2 on page 25.
Table 9-2. Clock AC Timing Specifications (See Table 6-2 on page 10 for Recommended Operating Conditions)
Symbol Characteristic
Maximum Processor Core Frequency
Unit Notes
1000 MHz 1267 MHz 1333 MHz 1420 MHz
VDD = 1.3V VDD = 1.3V VDD = 1.3 VDD = 1.3
MinMaxMinMaxMinMaxMinMax
fCORE Processor core
frequency 600 1000 600 1267 600 1333 600 1420 MHz (1)(8)(9)
fVCO VCO frequency 1200 2000 1200 2533 1200 2667 1200 2840 MHz (1)(9)
fSYSCLK SYSCLK frequency 33 167 33 167 33 167 33 167 MHz (1)(2)(8)
tSYSCLK SYSCLK cycle time 6.0 30 6 30 6 30 6 30 ns (2)
tKR, tKF SYSCLK rise and fall
time 1.0–1–1–1ns
(3)
tKHKL/tSYSCLK SYSCLK duty cycle
measured at OVDD/2 40 60 40 60 40 60 40 60 % (4)
SYSCLK jitter(5)(6) 150 150 150 150 ps (5)(6)
Internal PLL relock
time(7) 100 100 100 100 µs (7)
26
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
Notes: 1. Caution: The SYSCLK frequency and PLL_CFG[0:4] settings must be chosen such that the resulting SYSCLK (bus) fre-
quency, processor core frequency, and PLL (VCO) frequency do not exceed their respective maximum or minimum
operating frequencies. Refer to the PLL_CFG[0:4] signal description in Section “PLL Configuration” on page 38 for valid
PLL_CFG[0:4] settings.
2. Assumes a lightly-loaded, single-processor system.
3. Rise and fall times for the SYSCLK input measured from 0.4V to 1.4V.
4. Timing is guaranteed by design and characterization.
5. Guaranteed by design.
6. The SYSCLK driver’s closed loop jitter bandwidth should be less than 1.5 MHz at -3 dB.
7. Relock timing is guaranteed by design and characterization. PLL relock time is the maximum amount of time required for
PLL lock after a stable VDD and SYSCLK are reached during the power-on reset sequence. This specification also applies
when the PLL has been disabled and subsequently re-enabled during sleep mode. Also note that HRESET must be held
asserted for a minimum of 255 bus clocks after the PLL relock time during the power-on reset sequence.
8. Caution: If DFS is enabled, the SYSCLK frequency and PLL_CFG[0:4] settings must be chosen such that the resulting pro-
cessor frequency is greater than or equal to the minimum core frequency.
9. Caution: These values specify the maximum processor core and VCO frequencies when the device is operated at the nomi-
nal core voltage. If operating the device at the derated core voltage, the processor core and VCO frequencies must be
reduced.
Figure 9-1 provides the SYSCLK input timing diagram.
Figure 9-1. SYSCLK Input Timing Diagram
VM = Midpoint Voltage (OVDD/2)
Symbol Characteristic
Maximum Processor Core Frequency
Unit Notes
1000 MHz 1167 MHz
VDD = 1.1V VDD = 1.1V
Min Max Min Max
fCORE Processor core frequency 500 1000 500 1167 MHz (1)(8)(9)
fVCO VCO frequency 1000 2000 1000 2233 MHz (1)(9)
fSYSCLK SYSCLK frequency 33 167 33 167 MHz (1)(2)(8)
tSYSCLK SYSCLK cycle time 6 30 6 30 ns (2)
tKR, tKF SYSCLK rise and fall time 1 1 ns (3)
tKHKL/tSYSCLK SYSCLK duty cycle measured at OVDD/2 40 60 40 60 % (4)
SYSCLK jitter(5)(6) –150–150ps
(5)(6)
Internal PLL relock time(7) –100–100µs(7)
SYSCLK VMVMVM
tKHKL
tSYSCLK
CVIL
CVIH
tKR tKF
27
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
9.2.2 Processor Bus AC Specifications
Table 9-3 provides the processor bus AC timing specifications for the PC7447A as defined in Figure 7-2
on page 20 and Figure 9-2 on page 28..
Notes: 1. All input specifications are measured from the midpoint of the signal in question to the midpoint of the rising edge of the input
SYSCLK. All output specifications are measured from the midpoint of the rising edge of SYSCLK to the midpoint of the sig-
nal in question. All output timings assume a purely resistive 50 load (see Figure 7-2 on page 20). Input and output timings
are measured at the pin; time-of-flight delays must be added for trace lengths, vias, and connectors in the system.
Table 9-3. Processor Bus AC Timing Specifications(1) (at Recommended Operating Conditions, see Table 6-2 on page
10.)
Symbol(2) Parameter
All Speed Grades
UnitMin Max
tAVKH
tDVKH
tIVKH
tMVKH(8)
Input setup times:
A[0:35], AP[0:4]
D[0:63], DP[0:7]
AACK, ARTRY, BG, CKSTP_IN, DBG, DTI[0:3], GBL,
TT[0:3], QACK, TA, TBEN, TEA, TS,
EXT_QUAL, PMON_IN, SHD[0:1],
BMODE[0:1], BVSEL
1.8
1.8
1.8
1.8
ns
tAXKH
tDXKH
tIXKH
tMXKH(8)
Input hold times:
A[0:35], AP[0:4]
D[0:63], DP[0:7]
AACK, ARTRY, BG, CKSTP_IN, DBG, DTI[0:3], GBL,
TT[0:3], QACK, TA, TBEN, TEA, TS, EXT_QUAL,
PMON_IN, SHD[0:1]
BMODE[0:1], BVSEL
0
0
0
0
ns
tKHAV
tKHDV
tKHOV
Output valid times:
A[0:35], AP[0:4]
D[0:63], DP[0:7]
AACK, ARTRY, BR, CI, CKSTP_IN, DRDY, DTI[0:3],
GBL, HIT, PMON_OUT, QREQ, TBST, TSIZ[0:2], TT[0:3],
TS, SHD[0:1], WT
2
2
2
ns
tKHAX
tKHDX
tKHOX
Output hold times:
A[0:35], AP[0:4]
D[0:63], DP[0:7]
AACK, ARTRY, BR, CI, CKSTP_IN, DRDY, DTI[0:3],
GBL, HIT, PMON_OUT, QREQ, TBST, TSIZ[0:2], TT[0:3],
TS, SHD[0:1], WT
0.5
0.5
0.5
ns
tKHOE(5) SYSCLK to output enable 0.5 ns
tKHOZ(5) SYSCLK to output high impedance (all except TS, ARTRY, SHD0,
SHD1)–3.5ns
tKHTSPZ(3)(4)(5) SYSCLK to TS high impedance after precharge 1 tSYSCLK
tKHARP(3)(5)(6)(7) Maximum delay to ARTRY/SHD0/SHD1 precharge 1 tSYSCLK
tKHARPZ(3)(5)(6)(7) SYSCLK to ARTRY/SHD0/SHD1 high impedance after precharge 2 tSYSCLK
28
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
2. The symbology used for timing specifications herein follows the pattern of t(signal)(state)(reference)(state) for inputs and
t(reference)(state)(signal)(state) for outputs. For example, tIVKH symbolizes the time input signals (I) reach the valid state (V) relative to
the SYSCLK reference (K) going to the high (H) state or input setup time. And tKHOV symbolizes the time from SYSCLK (K)
going high (H) until outputs (O) are valid (V) or output valid time. Input hold time can be read as the time that the input signal
(I) went invalid (X) with respect to the rising clock edge (KH) (note the position of the reference and its state for inputs) and
output hold time can be read as the time from the rising edge (KH) until the output went invalid (OX).
3. tSYSCLK is the period of the external clock (SYSCLK) in ns. The numbers given in the table must be multiplied by the period of
SYSCLK to compute the actual time duration (in ns) of the parameter in question.
4. According to the bus protocol, TS is driven only by the currently active bus master. It is asserted low and precharged high
before returning to high impedance, as shown in Figure 9-3 on page 29. The nominal precharge width for TS is 0.5 × tSYSCLK,
that is, less than the minimum tSYSCLK period, to ensure that another master asserting TS on the following clock will not con-
tend with the precharge. Output valid and output hold timing is tested for the signal asserted. Output valid time is tested for
precharge.The high-impedance behavior is guaranteed by design.
5. Guaranteed by design and not tested.
6. According to the bus protocol, ARTRY can be driven by multiple bus masters through the clock period immediately following
AACK. Bus contention is not an issue because any master asserting ARTRY will be driving it low. Any master asserting it low
in the first clock following AACK will then go to high impedance for 1 clock before precharging it high during the second cycle
after the assertion of AACK. The nominal precharge width for ARTRY is 1.0 tSYSCLK; that is, it should be high impedance as
shown in Figure 9-3 on page 29 before the first opportunity for another master to assert ARTRY. Output valid and output hold
timing is tested for the signal asserted.The high-impedance behavior is guaranteed by design.
7. According to the MPX bus protocol, SHD0 and SHD1 can be driven by multiple bus masters beginning the cycle of TS. Tim-
ing is the same as ARTRY, that is, the signal is high impedance for a fraction of a cycle, then negated for up to an entire
cycle (crossing a bus cycle boundary) before being three-stated again. The nominal precharge width for SHD0 and SHD1 is
1.0 tSYSCLK. The edges of the precharge vary depending on the programmed ratio of core to bus (PLL configurations).
8. BMODE[0:1] and BVSEL are mode select inputs and are sampled before and after HRESET negation. These parameters
represent the input setup and hold times for each sample. These values are guaranteed by design and not tested. These
inputs must remain stable after the second sample. See Figure 9-2 on page 28 for sample timing.
Figure 9-2 provides the mode select input timing diagram for the PC7447A. The mode select inputs are
sampled twice, once before and once after HRESET negation.
Figure 9-2. Mode Input Sample Timing Diagram
HRESET
Mode Signals
VMVM
VM = Midpoint Voltage (OVDD/2)
SYSCLK
1st Sample 2nd Sample
29
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Figure 9-3 provides the input/output timing diagram for the PC7447A.
Figure 9-3. Input/Output Timing Diagram
Note: VM = Midpoint Voltage (OVDD/2)
SYSCLK
All Inputs
VM
All Outputs
VM
(Except TS,
All Outputs
TS
VM
tKHOE
ARTRY, SHD0, SHD1)
(Except TS,
ARTRY, SHD0, SHD1)
ARTRY,
SHD0,
SHD1
tAVKH
tKHAV
tMVKH
tIVKH
tAXKH
tIXKH
tMXKH
tKHDV
tKHOV
tKHAX
tKHDX
tKHOX
tKHOZ
tKHTSPZ
tKHTSX
tKHTSV
tKHTSV
tKHARV tKHARP
tKHARX
tKHARPZ
30
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
9.2.3 IEEE 1149.1 AC Timing Specifications
Table 9-4 provides the IEEE 1149.1 (JTAG) AC timing specifications as defined in Figure 9-5 through
Figure 9-8 on page 32.
Notes: 1. All outputs are measured from the midpoint voltage of the falling/rising edge of TCLK to the midpoint of the signal in ques-
tion. The output timings are measured at the pins. All output timings assume a purely resistive 50 load (see Figure 9-4).
Time-of-flight delays must be added for trace lengths, vias and connectors in the system.
2. TRST is an asynchronous level sensitive signal. The time is for test purposes only.
3. Non-JTAG signal input timing with respect to TCK.
4. Non-JTAG signal output timing with respect to TCK.
5. Guaranteed by design and characterization.
Figure 9-4 provides the AC test load for TDO and the boundary-scan outputs of the PC7457.
Figure 9-4. Alternate AC Test Load for the JTAG Interface
Table 9-4. JTAG AC Timing Specifications (Independent of SYSCLK)(1)at Recommended Operating Conditions
(see Table 6-2 on page 10)
Symbol Parameter Min Max Unit
fTCLK TCK frequency of operation 0 33.3 MHz
tTCLK TCK cycle time 30 ns
tJHJL TCK clock pulse width measured at 1.4V 15 ns
tJR and tJF TCK rise and fall times 2 ns
tTRST(2) TRST assert time 25 ns
tDVJH(3)
tIVJH
Input Setup Times:
Boundary-scan data
TMS, TDI
4
0
ns
tDXJH(3)
tIXJH
Input Hold Times:
Boundary-scan data
TMS, TDI
20
25
ns
tJLDV(4)
tJLOV
Valid Times:
Boundary-scan data
TDO
4
4
20
25
ns
tJLDX(4)
tJLOX
Output hold times:
Boundary-scan data
TDO
30
30
tJLDZ(4)(5)
tJLOZ
TCK to output high impedance:
Boundary-scan data
TDO
3
3
19
9
ns
Output Z0 = 50
RL = 50
OVDD/2
31
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Figure 9-5. JTAG Clock Input Timing Diagram
Note: VM = Midpoint Voltage (OVDD/2)
Figure 9-6. TRST Timing Diagram
Note: VM = Midpoint Voltage (OVDD/2)
Figure 9-7. Boundary-scan Timing Diagram
Note: VM = Midpoint Voltage (OVDD/2)
VMVMVM
tTCLK
tJR tJF
tJHJL
TCLK
TRST
t
TRST
VM
VM
VMTCK
Boundary
Data Inputs
Boundary
Data Outputs
Boundary
Data Outputs
tDXJH
tDVJH
tJLDV
tJLDZ
Output Data Valid
tJLDX
VM
Input
Data Valid
Output Data Valid
32
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
Figure 9-8. Test Access Port Timing Diagram
Note: VM = Midpoint Voltage (OVDD/2)
10. Preparation for Delivery
10.1 Handling
MOS devices must be handled with certain precautions to avoid damage due to accumulation of static
charge. Input protection devices have been designed in the chip to minimize the effect of static buildup.
However, the following handling practices are recommended:
Devices should be handled on benches with conductive and grounded surfaces
Ground test equipment, tools and operator
Do not handle devices by the leads
Store devices in conductive foam or carriers
Avoid use of plastic, rubber or silk in MOS areas
Maintain relative humidity above 50% if practical
11. Package Mechanical Data
The following sections provide the package parameters and mechanical dimensions for the HITCE
package.
11.1 Package Parameters for the PC7447A, 360 HITCE
The package parameters are as provided in the following list. The package type is 25 × 25 mm, 360-lead
high coefficient of the thermal expansion ceramic ball grid array (HITCE).
Package outline 25 mm × 25 mm
Interconnects 360 (19 × 19 ball array - 1)
Pitch 1.27 mm (50 mil)
Minimum module height 2.72 mm
Maximum module height 3.24 mm
Ball diameter 0.89 mm (35 mil)
tJLOX
Input Data
Valid
tIVJH tIXJH
tJLOV
tJLOZ
Output Data Valid
Output Data Valid
VM
TCK
TDI, TMS
TDO
TDO
VM
33
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
11.2 Mechanical Dimensions for the PC7447A, 360 HITCE
Figure 11-1 provides the mechanical dimensions and bottom surface nomenclature for the PC7447A, 360 HITCE package.
Figure 11-1. Mechanical Dimensions and Bottom Surface Nomenclature for the PC7447A, 360 CBGA Package
Notes: 1. Dimensioning and tolerance per ASME Y14.5M, 1994
2. Dimensions in millimeters
3. Top side A1 corner index is a metallized feature with various shapes. Bottom side A1 corner is designated with a ball missing
from the array
CA
360X
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
B0.3
A
0.15
b
U
W
V
12345678910111213141516 1718 19
0.2
2X
C
A1 CORNER
B
0.2
2X
D
E
E3
E2
E1
E4
D2
D4
D3 D1
Capacitor Region
1
A
0.15 A
0.35 A
A
A1
A2
A3
Millimeters
DIM MIN MAX
A 2.72 3.20
A1 0.80 1
A2 1.10 1.30
A3 – 0.6
b 0.82 0.93
D 25 BSC
D1 – 11.3
D2 8
D3 – 6.5
D4 9.76 9.96
e 1.27 BSC
E 25 BSC
E1 – 11.3
E2 8
E3 – 6.5
E4 8.41 8.61
e
34
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
11.3 Package Parameters for the PC7447A, 360 HITCE RoHS-Compliant BGA
The package parameters are as provided in the following list. The package type is 25 × 25 mm, 360
lead-free high coefficient of thermal expansion ceramic ball grid array (HITCE).
Package outline 25 mm × 25 mm
Interconnects 360 (19 × 19 ball array - 1)
Pitch 1.27 mm (50 mil)
Minimum module height 2.32 mm
Maximum module height 2.80 mm
Ball diameter 0.89 mm (35 mil)
Coefficient of thermal expansion 12.3 ppm/°C
35
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
11.4 Mechanical Dimensions for the PC7447A, 360 HITCE RoHS-Compliant BGA
Figure 11-1 provides the mechanical dimensions and bottom surface nomenclature for the PC7447A, 360 HITCE BGA
package.
Figure 11-2. Mechanical Dimensions and Bottom Surface Nomenclature for the PC7447A, 360 HITCE RoHS-Compliant
BGA Package
CA
360X
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
B0.3
A
0.15
b
U
W
V
12345678910111213141516 1718 19
0.2
2X
C
A1 CORNER
B
0.2
2X
D
E
E3
E2
E1
E4
D2
D4
D3 D1
Capacitor Region
1
A
0.15 A
0.35 A
A
A1
A2
A3
Millimeters
DIM MIN MAX
A 2.32 2.80
A1 0.40 0.60
A2 1.10 1.30
A3 – 0.6
b 0.6 0.9
D 25 BSC
D1 – 11.3
D2 8
D3 – 6.5
D4 9.76 9.96
e 1.27 BSC
E 25 BSC
E1 – 11.3
E2 8
E3 – 6.5
E4 8.41 8.61
e
36
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
11.5 Package Parameters for the PC7447A, 360 HCTE LGA
The package parameters are as provided in the following list. The package type is 25 × 25 mm, 360 high
coefficient of thermal expansion ceramic land grid array (HCTE).
Package outline 25 mm × 25 mm
Interconnects 360 (19 × 19 ball array - 1)
Pitch 1.27 mm (50 mil)
Minimum module height 1.92 mm
Maximum module height 2.20 mm
Coefficient of thermal expansion 12.3 ppm/°C
37
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
11.6 Mechanical Dimensions for the MPC7447A, 360 HCTE LGA
Figure 11-3 provides the mechanical dimensions and bottom surface nomenclature for the PC7447A,
360 HCTE LGA package.
Figure 11-3. Mechanical Dimensions and Bottom Surface Nomenclature for the PC7447A, 360 HITCE LGA Package
CA
360X
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
B0.3
A
0.15
b
U
W
V
12345678910111213141516 1718 19
0.2
2X
C
A1 CORNER
B
0.2
2X
D
E
E3
E2
E1
E4
D2
D4
D3 D1
Capacitor Region
1
0.15 A
0.35 A
Millimeters
Dim Min Max
A 1.92 2.20
A1 1.10 1.30
A2 – 0.6
b 0.82 0.93
D 25 BSC
D1 – 11.3
D2 8
D3 – 6.5
D4 9.76 9.96
e 1.27 BSC
E 25 BSC
E1 – 11.3
E2 8
E3 – 6.5
E4 8.41 8.61
e
A
A
A1
A2
38
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
11.7 Substrate Capacitors for the PC7447A, 360 HITCE
Figure 11-4 shows the connectivity of the substrate capacitor pads for the PC7447A, 360 HITCE. All capacitors are 100 nF.
Figure 11-4. Substrate Bypass Capacitors for the PC7447A, 360 HITCE
12. System Design Information
This section provides system and thermal design recommendations for successful application of the
PC7447A.
12.1 PLL Configuration
The PC7447A PLL is configured by the PLL_CFG[0:4] signals. For a given SYSCLK (bus) frequency, the
PLL configuration signals set the internal CPU and VCO frequency of operation. The PLL configuration
for the PC7447A is shown in Table 12-1 on page 39 for a set of example frequencies. In this example,
shaded cells represent settings that, for a given SYSCLK frequency, result in core and/or VCO frequen-
cies that do not comply with the 1400 MHz column in Table 9-2 on page 25. When enabled, dynamic
frequency switching (DFS) also affects the core frequency by halving the bus-to-core multiplier; see sec-
tion “Dynamic Frequency Switching (DFS)” on page 17 for more information.
1
C1-2
C1-1 C2-1 C3-1 C4-1 C5-1 C6-1
C6-2C5-2C4-2C3-2C2-2
C18-1
C18-2 C17-2 C16-2 C15-2 C14-2 C13-2
C13-1C14-1C15-1C16-1C17-1
C12-1
C12-2 C11-2 C10-2 C9-2 C8-2 C7-2
C7-1C8-1C9-1
C10-1C11-1
C19-2
C19-1 C20-1 C21-1 C22-1 C23-1 C24-1
C24-2C23-2C22-2C21-2C20-2
A1 CORNER
C1 GND VDD
C2 GND VDD
C3 GND OVDD
C4 GND VDD
C5 GND VDD
C6 GND VDD
C7 GND VDD
C8 GND VDD
C9 GND VDD
C10 GND VDD
C11 GND VDD
C12 GND VDD
C13 GND VDD
C14 GND VDD
C15 GND VDD
C16 GND OVDD
C17 GND VDD
C18 GND OVDD
C19 GND OVDD
C20 GND VDD
C21 GND OVDD
C22 GND VDD
C23 GND OVDD
C24 GND VDD
Capacitor
Pad Number
-1 -2
39
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Note that when DFS is enabled the resulting core frequency must meet the minimum core frequency
requirements described in Table 9-2 on page 25.
Table 12-1. PC7447A Microprocessor PLL Configuration Example for 1420-MHz Parts
PLL_CFG[0:4]
Example Bus-to-Core Frequency in MHz (VCO Frequency in MHz)
Bus-to-Core
Multiplier
Core-to-VCO
Multiplier
Bus (SYSCLK) Frequency
33.33
MHz
50
MHz
66.66
MHz
75
MHz
83
MHz
100
MHz
133.33
MHz
166.66
MHz
01000 2x 2x
10000 3x 2x
10100 4x 2x 667
(1333)
10110 5x 2x 667
(1333)
835
(1670)
10010 5.5x 2x 733
(1466)
919
(1837)
11010 6x 2x 600
(1200)
800
(1600)
1002
(2004)
01010 6.5x 2x 650
(1300)
866
(1730)
1086
(2171)
00100 7x 2x 700
(1400)
931
(1862)
1169
(2338)
00010 7.5x 2x 623
(1245)
750
(1500)
1000
(2000)
1253
(2505)
11000 8x 2x 600
(1200)
664
(1328)
800
(1600)
1064
(2128)
1336
(2672)
01100 8.5x 2x 638
(1276)
706
(1412)
850
(1700)
1131
(2261)
1417
(2833)
01111 9x 2x 600
(1200)
675
(1350)
747
(1494)
900
(1800)
1197
(2394)
01110 9.5x 2x 633
(1266)
712
(1524)
789
(1578)
950
(1900)
1264
(2528)
10101 10x 2x 667
(1333)
750
(1500)
830
(1660)
1000
(2000)
1333
(2667)
10001 10.5x 2x 700
(1400)
938
(1876)
872
(1744)
1050
(2100)
1397
(2793)
10011 11x 2x 733
(1466)
825
(1650)
913
(1826)
1100
(2200)
00000 11.5x 2x 766
(532)
863
(1726)
955
(1910)
1150
(2300)
10111 12x 2x 600
(1200)
800
(1600)
900
(1800)
996
(1992)
1200
(2400)
40
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
Notes: 1. PLL_CFG[0:4] settings not listed are reserved.
2. The sample bus-to-core frequencies shown are for reference only. Some PLL configurations may select bus, core, or VCO
frequencies that are not useful, not supported, or not tested for by the PC7455; see Section “Clock AC Specifications” on
page 25 for valid SYSCLK, core, and VCO frequencies.
3. In PLL-bypass mode, the SYSCLK input signal clocks the internal processor directly and the PLL is disabled. However, the
bus interface unit requires a 2x clock to function. Therefore, an additional signal, EXT_QUAL, must be driven at one-half the
frequency of SYSCLK and offset in phase to meet the required input setup tIVKH and hold time tIXKH (see Table 9-3 on
page 27). The result will be that the processor bus frequency will be one-half SYSCLK while the internal processor is
clocked at SYSCLK frequency. This mode is intended for factory use and emulator tool use only.
Note: The AC timing specifications given in this document do not apply in PLL-bypass mode.
4. In PLL-off mode, no clocking occurs inside the PC7447A regardless of the SYSCLK input.
11111 12.5x 2x 600
(1200)
833
(1666)
938
(1876)
1038
(2076)
1250
(2500)
01011 13x 2x 650
(1300)
865
(1730)
975
(1950)
1079
(2158)
1300
(2600)
11100 13.5x 2x 675
(1350)
900
(1800)
1013
(2026)
1121
(2242)
1350
(2700)
11001 14x 2x 700
(1400)
933
(1866)
1050
(2100)
1162
(2324)
1400
(2800)
00011 15x 2x 750
(1500)
1000
(2000)
1125
(2250)
1245
(2490)
11011 16x 2x 800
(1600)
1066
(2132)
1200
(2400)
1328
(2656)
00001 17x 2x 850
(1900)
1132
(2264)
1275
(2550)
1411
(2822)
00101 18x 2x 600
(1200)
900
(1800)
1200
(2400)
1350
(2700)
00111 20x 2x 667
(1334)
1000
(2000)
1332
(2664)
01001 21x 2x 700
(1400)
1050
(2100)
1399
(2797)
01101 24x 2x 800
(1600)
1200
(2400)
11101 28x 2x 933
(1866)
1400
(2800)
00110 PLL bypass PLL off, SYSCLK clocks core circuitry directly
11110 PLL off PLL off, no core clocking occurs
Table 12-1. PC7447A Microprocessor PLL Configuration Example for 1420-MHz Parts (Continued)
PLL_CFG[0:4]
Example Bus-to-Core Frequency in MHz (VCO Frequency in MHz)
Bus-to-Core
Multiplier
Core-to-VCO
Multiplier
Bus (SYSCLK) Frequency
33.33
MHz
50
MHz
66.66
MHz
75
MHz
83
MHz
100
MHz
133.33
MHz
166.66
MHz
41
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
12.2 PLL Power Supply Filtering
The AVDD power signal is provided on the PC7447A to provide power to the clock generation PLL. To
ensure stability of the internal clock, the power supplied to the AVDD input signal should be filtered of any
noise in the 500 KHz to 10 MHz resonant frequency range of the PLL. A circuit similar to the one shown
in Figure 12-1 using surface mount capacitors with minimum effective series inductance (ESL) is
recommended.
The circuit should be placed as close as possible to the AVDD pin to minimize noise coupled from nearby
circuits. It is often possible to route directly from the capacitors to the AVDD pin, which is on the periphery
of the 360 HITCE footprint.
Figure 12-1. PLL Power Supply Filter Circuit
12.3 Decoupling Recommendations
Due to the PC7447A dynamic power management feature, large address and data buses, and high
operating frequencies, the PC7447A can generate transient power surges and high frequency noise in
its power supply, especially while driving large capacitive loads. This noise must be prevented from
reaching other components in the PC7447A system, and the PC7447A itself requires a clean, tightly reg-
ulated source of power. Therefore, it is recommended that the system designer use sufficient decoupling
capacitors, typically one capacitor for every 1-2 VDD pins, and a similar or lesser amount for the OVDD
pins, placed as close as possible to the power pins of the PC7447A. It is also recommended that these
decoupling capacitors receive their power from separate VDD, OVDD, and GND power planes in the PCB,
utilizing short traces to minimize inductance.
These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic surface mount technology (SMT)
capacitors should be used to minimize lead inductance. Orientations where connections are made along
the length of the part, such as 0204, are preferable but not mandatory. Consistent with the recommenda-
tions of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall,
1993) and contrary to previous recommendations for decoupling Freescale microprocessors, multiple
small capacitors of equal value are recommended over using multiple values of capacitance.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the VDD and OVDD planes, to enable quick recharging of the smaller chip capacitors. These bulk
capacitors should have a low equivalent series resistance (ESR) rating to ensure the quick response
time necessary. They should also be connected to the power and ground planes through two vias to min-
imize inductance. Suggested bulk capacitors are: 100-330 µF (AVX TPS tantalum or Sanyo OSCON).
12.4 Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. Unless otherwise noted, unused active low inputs should be tied to OVDD, and unused active high
inputs should be connected to GND. All NC (no connect) signals must remain unconnected.
Power and ground connections must be made to all external VDD, OVDD, and GND pins in the PC7447A.
VDD
10
2.2 µF2.2 µF
GND
AVDD
Low ESL surface mount capacitors
42
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
For backward compatibility with the PC7447 to the PC7447A, the new power and ground signals (for-
merly NC, see Table 8-1 on page 21) may be left unconnected. There is no performance degradation
associated with leaving these pins unconnected. However, future devices may require these additional
power and ground signals to be connected to achieve maximum performance, and it is recommended
that new designs include the additional connections to facilitate future upgrades. See also section
“Pinout Listings” on page 21 for additional information.
12.5 Output Buffer DC Impedance
The PC7447A processor bus drivers are characterized over process, voltage, and temperature. To mea-
sure Z0, an external resistor is connected from the chip pad to OVDD or GND. The value of each resistor
is varied until the pad voltage is OVDD/2. Figure 12-2 on page 42 shows the driver impedance
measurement.
The output impedance is the average of two components–the resistances of the pull-up and pull-down
devices. When data is held low, SW2 is closed (SW1 is open), and RN is trimmed until the voltage at the
pad equals OVDD/2. RN then becomes the resistance of the pull-down devices. When data is held high,
SW1 is closed (SW2 is open), and RP is trimmed until the voltage at the pad equals OVDD/2. RP then
becomes the resistance of the pull-up devices. RP and RN are designed to be close to each other in
value. Then, Z0 = (RP + RN)/2.
Figure 12-2. Driver Impedance Measurement
Table 12-2 summarizes the signal impedance results. The impedance increases with junction tempera-
ture and is relatively unaffected by bus voltage.
Table 12-2. Impedance Characteristics with VDD = 1.5V, OVDD = 1.8V ±5%, Tj = 5° - 85°C
Impedance Processor bus L3 Bus Unit
Z0
Typical 33 – 42 34 – 42
Maximum 31 – 51 32 – 44
OVDD
OGND
SW2
SW1
RN
RP
Pad
Data
43
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
12.6 Pull-up/Pull-down Resistor Requirements
The PC7447A requires high-resistive (weak: 4.7-K) pull-up resistors on several control pins of the bus
interface to maintain the control signals in the negated state after they have been actively negated and
released by the PC7447A or other bus masters. These pins are: TS, ARTRY, SHDO, and SHD1.
Some pins designated as being factory test pins must be pulled up to OVDD or down to GND to ensure
proper device operation. For the PC7447A, 360 BGA, the pins that must be pulled up to OVDD are
LSSD_MODE and TEST[0:3]; the pins that must be pulled down to GND are: L1_TSTCLK and TEST[4].
The CKSTP_IN signal should likewise be pulled up through a pull-up resistor (weak or stronger: 4.7–1
K) to prevent erroneous assertions of this signal.
In addition, the PC7447A has one open-drain style output that requires a pull-up resistor (weak or stron-
ger: 4.7–1 K) if it is used by the system. This pin is CKSTP_OUT.
If pull-down resistors are used to configure BVSEL, the resistors should be less than 250 (see Table 8-
1 on page 21). Because PLL_CFG[0:4] must remain stable during normal operation, strong pull-up and
pull-down resistors (1 K or less) are recommended to configure these signals in order to protect
against erroneous switching due to ground bounce, power supply noise or noise coupling.
During inactive periods on the bus, the address and transfer attributes may not be driven by any master
and may, therefore, float in the high-impedance state for relatively long periods of time. Because the
PC7447A must continually monitor these signals for snooping, this float condition may cause excessive
power draw by the input receivers on the PC7447A or by other receivers in the system. These signals
can be pulled up through weak (10-K) pull-up resistors by the system, address bus driven mode
enabled (see the MPC7450 RISC Microprocessor Family Users’ Manual for more information on this
mode), or they may be otherwise driven by the system during inactive periods of the bus to avoid this
additional power draw. Preliminary studies have shown the additional power draw by the PC7447A input
receivers to be negligible and, in any event, none of these measures are necessary for proper device
operation. The snooped address and transfer attribute inputs are: A[0:35], AP[0:4], TT[0:4], CI, WT, and
GBL.
If address or data parity is not used by the system, and respective parity checking is disabled through
HID1, the input receivers for those pins are disabled and do not require pull-up resistors, and may be left
unconnected by the system. If extended addressing is not used (HID0[XAEN] = 0), A[0:3] are unused
and must be pulled low to GND through weak pull-down resistors; additionally, if address parity checking
is enabled (HID1[EBA] = 1) and extended addressing is not used, AP[0] must be pulled up to OVDD
through a weak pull-up resistor. If the PC7447A is in 60x bus mode, DTI[0:3] must be pulled low to GND
through weak pull-down resistors. The data bus input receivers are normally turned off when no read
operation is in progress and, therefore, do not require pull-up resistors on the bus. Other data bus receiv-
ers in the system, however, may require pull-ups, or that those signals be otherwise driven by the
system during inactive periods by the system. The data bus signals are: D[0:63] and DP[0:7].
44
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
12.7 JTAG Configuration Signals
Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the
IEEE 1149.1 specification but is provided on all processors that implement the PowerPC architecture.
While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals,
more reliable power-on reset performance will be obtained if the TRST signal is asserted during power-
on reset. Because the JTAG interface is also used for accessing the common on-chip processor (COP)
function, simply tying TRST to HRESET is not practical.
The COP function of these processors allows a remote computer system (typically a PC with dedicated
hardware and debugging software) to access and control the internal operations of the processor. The
COP interface connects primarily through the JTAG port of the processor, with some additional status
monitoring signals. The COP port requires the ability to independently assert HRESET or TRST in order
to fully control the processor. If the target system has independent reset sources, such as voltage moni-
tors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must
be merged into these signals with logic.
The arrangement shown in Figure 12-3 on page 45 allows the COP port to independently assert
HRESET or TRST, while ensuring that the target can drive HRESET as well. If the JTAG interface and
COP header will not be used, TRST should be tied to HRESET through a 0. isolation resistor so that it
is asserted when the system reset signal (HRESET) is asserted, ensuring that the JTAG scan chain is
initialized during power-on. Although Freescale recommends that the COP header be designed into the
system as shown in Figure 12-3 on page 45, if this is not possible, the isolation resistor will allow future
access to TRST in the case where a JTAG interface may need to be wired onto the system in debug
situations.
The COP header shown in Figure 12-3 on page 45 adds many benefits: breakpoints, watchpoints, regis-
ter and memory examination/modification, and other standard debugger features are possible through
this interface, and can be as inexpensive as an unpopulated footprint for a header to be added when
needed.
The COP interface has a standard header for connection to the target system, based on the 0.025 inch
square-post, 0.100 inch centered header assembly (often called a Berg header). The connector typically
has pin 14 removed as a connector key.
There is no standardized way to number the COP header shown in Figure 12-3 on page 45; conse-
quently, many different pin numbers have been observed from emulator vendors. Some are numbered
top-to-bottom then left-to-right, while others use left-to-right then top-to-bottom, while still others number
the pins counter clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement
recommended in Figure 12-3 on page 45 is common to all known emulators.
The QACK signal shown in Figure 12-3 on page 45 is usually connected to the PCI bridge chip in a sys-
tem and is an input to the PC7447A informing it that it can go into the quiescent state. Under normal
operation this occurs during a low-power mode selection. In order for COP to work, the PC7447A must
see this signal asserted (pulled down). While shown on the COP header, not all emulator products drive
this signal. If the product does not, a pull-down resistor can be populated to assert this signal. Addition-
ally, some emulator products implement open-drain type outputs and can only drive QACK asserted; for
these tools, a pull-up resistor can be implemented to ensure this signal is negated when it is not being
driven by the tool. Note that the pull-up and pull-down resistors on the QACK signal are mutually exclu-
sive and it is never necessary to populate both in a system. To preserve correct power-down operation,
QACK should be merged through logic so that it also can be driven by the PCI bridge.
45
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Figure 12-3. JTAG Interface Connection
Notes: 1. RUN/STOP, normally found on pin 5 of the COP header, is not implemented on the PC7447A. Connect
pin 5 of the COP header to OVDD with a 10 k pull-up resistor.
2. Key location; pin 14 is not physically present on the COP header.
3. Component not populated. Populate only if debug tool does not drive QACK.
4. Populate only if debug tool uses an open-drain type output and does not actively de-assert QACK.
5. If the JTAG interface is implemented, connect HRESET from the target source to TRST from the COP
header though an AND gate to TRST of the part. If the JTAG interface is not implemented, connect
HRESET from the target source to TRST of the part through a 0 isolation resistor.
6. The COP port and target board should be able to independently assert HRESET and TRST to the pro-
cessor in order to fully control the processor as shown above.
HRESET HRESET(6)
HRESET
13
SRESET
SRESET SRESET
11
VDD_SENSE
6
5(1)
15
2 k10 k
10 k
10 k
OVDD
OVDD
OVDD
OVDD
CHKSTP_IN CHKSTP_IN
8TMS
TDO
TDI
TCK
TMS
TDO
TDI
TCK
9
1
3
4TRST
7
16
2
10
14(2)
Key
QACK
OVDD
OVDD
OVDD
TRST(6)
10 k
10 k
10 k
10 k
OVDD
QACK
QACK
CHKSTP_OUT
CHKSTP_OUT
3
13
9
5
1
6
10
2
15
11
7
16
12
8
4
KEY
No Pin
COP Connector
Physical Pin Out
10 k(4) OVDD
OVDD
1
2 k(3)
0(5)
12
NC
NC
From Target
Board Sources
(if any)
COP Header
10 k
46
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
13. Ordering Information
Notes: 1. For availability of the different versions, contact your local e2v sales office.
2. The letter X in the part number designates a "Prototype" product that has not been qualified by e2v. Reliability of a PCX part-
number is not guaranteed and such part-number shall not be used in Flight Hardware. Product changes may still occur while
shipping prototypes.
14. Definitions
14.1 Life Support Applications
These products are not designed for use in life support appliances, devices or systems where malfunc-
tion of these products can reasonably be expected to result in personal injury. e2v customers using or
selling these products for use in such applications do so at their own risk and agree to fully indemnify e2v
for any damages resulting from such improper use or sale.
M: -55˚C, +125˚C
xx y xxx nnnn L x7447
Part
Identifier
7447A V: -40˚C, +110˚C
GH: HiTCE
GHY: HiTCE RoHS compliant
LH: LGA
N: 1.1V ± 50 mV
1167 MHz (N-Spec)
1000 MHz (N-Spec) B
Product
Code(1)
PC(X)(2)
Package(1) Max Internal
Processor Speed(1) Revision
Level(1)
Application
Modifier (1)
Temperature
Range Tj (1)
47
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
15. Document Revision History
Table 15-1 provides a revision history for this hardware specification.
Table 15-1. Document Revision History
Revision Number Date Substantive Change(s)
E 01/07 Name change from Atmel to e2v
D 07/06 Page 35: b parameter modification; remove preliminary.
C 12/05 Add RoHS package and LGA package.
B 07/05
Changed die size.
Table 9-2 on page 25: Modified jitter specifications to conform to JEDEC standards,
changed jitter specification to cycle-to-cycle jitter (instead of long- and short-term jitter);
changed jitter bandwidth recommendations.
Added tKHTSV
, tKHARV
, tKHTSX, and tKHARX to Table 9-3 on page 27; these were previously
grouped with tKHOV and tKHOX.
Note: Documentation change only; the values for the output valid and output hold AC
timing specifications remain unchanged for TS, ARTRY, and SHD[0:1].
A 04/04 Initial revision.
48
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
i
0833E–HIREL–01/07
e2v semiconductors SAS 2007
PC7447A
Table of Contents
Features .................................................................................................... 1
Description ............................................................................................... 1
Screening ................................................................................................. 1
1 Block Diagram .......................................................................................... 2
2 Features .................................................................................................... 3
3 General Parameters ................................................................................. 7
4 Signal Description ................................................................................... 8
5 Detailed Specification ............................................................................. 9
6 Applicable Documents ............................................................................ 9
6.1 Design and Construction ........................................................................................9
6.1.1 Terminal Connections ............................................................................9
6.2 Absolute Maximum Ratings ....................................................................................9
6.3 Recommended Operating Conditions ..................................................................10
6.4 Thermal Characteristics .......................................................................................11
6.4.1 Package Characteristics .......................................................................11
6.4.2 Internal Package Conduction Resistance ............................................11
6.4.3 Thermal Management Information .......................................................12
6.4.4 Thermal Interface Materials ..................................................................13
6.4.5 Power Consumption .............................................................................19
7 Pin Assignment ...................................................................................... 20
8 Pinout Listings ....................................................................................... 21
9 Electrical Characteristics ...................................................................... 24
9.1 Static Characteristics ............................................................................................24
9.2 Dynamic Characteristics .......................................................................................25
9.2.1 Clock AC Specifications .......................................................................25
9.2.2 Processor Bus AC Specifications .........................................................27
9.2.3 IEEE 1149.1 AC Timing Specifications ................................................30
10 Preparation for Delivery ........................................................................ 32
10.1 Handling .............................................................................................................32
11 Package Mechanical Data ..................................................................... 32
ii
0833E–HIREL–01/07
PC7447A
e2v semiconductors SAS 2007
11.1 Package Parameters for the PC7447A, 360 HITCE ..........................................32
11.2 Mechanical Dimensions for the PC7447A, 360 HITCE ......................................33
11.3 Package Parameters for the PC7447A, 360 HITCE RoHS-Compliant BGA ......34
11.4 Mechanical Dimensions for the PC7447A, 360 HITCE RoHS-Compliant BGA .35
11.5 Package Parameters for the PC7447A, 360 HCTE LGA ...................................36
11.6 Mechanical Dimensions for the MPC7447A, 360 HCTE LGA ............................37
11.7 Substrate Capacitors for the PC7447A, 360 HITCE ..........................................38
12 System Design Information .................................................................. 38
12.1 PLL Configuration ...............................................................................................38
12.2 PLL Power Supply Filtering ................................................................................41
12.3 Decoupling Recommendations ..........................................................................41
12.4 Connection Recommendations ..........................................................................41
12.5 Output Buffer DC Impedance .............................................................................42
12.6 Pull-up/Pull-down Resistor Requirements ..........................................................43
12.7 JTAG Configuration Signals ...............................................................................44
13 Ordering Information ............................................................................. 46
14 Definitions .............................................................................................. 46
14.1 Life Support Applications ....................................................................................46
15 Document Revision History .................................................................. 47
Table of Contents ...................................................................................... i
Whilst e2v has taken care to ensure the accuracy of the information contained herein it accepts no responsibility for the consequences of any
use thereof and also reserves the right to change the specific ation of goods without notice. e2v accepts no liability beyond that set out in its stan-
dard conditions of sale in respect of infringement of third party patents arising from the use of tubes or other devices in accorda nce w ith inform a-
tion contained herein.
How to reach us
Home page: www.e2v.com
Sales Office:
Northern Europe
e2v ltd
106 Waterhouse Lane
Chelmsford
Essex CM1 2QU
England
Tel: +44 (0)1245 493493
Fax: +44 (0)1245 492492
E-Mail: enquiries@e2v.com
Southern Europe
e2v sas
16 Burospace
F-91572 Bièvres
Cedex
France
Tel: +33 (0) 16019 5500
Fax: +33 (0) 16019 5529
E-Mail: enquiries-fr@e2v.com
Germany and Austria
e2v gmbh
Industriestraße 29
82194 Gröbenzell
Germany
Tel: +49 (0) 8142 41057-0
Fax: +49 (0) 8142 284547
E-Mail: enquiries-de@e2v.com
Americas
e2v inc.
4 Westchester Plaza
Elmsford
NY 10523-1482
USA
Tel: +1 (914) 592 6050 or
1-800-342-5338,
Fax: +1 (914) 592-5148
E-Mail: enquiries-na@e2v.com
Asia Pacific
e2v
Bank of China Tower
30th floor office 7
1 Garden Rd Central
Hong Kong
Tel: +852 2251 8227/8/9
Fax: +852 2251 8238
E-Mail: enquiries-hk@e2v.com
Product Contact:
e2v
Avenue de Rochepleine
BP 123 - 38521 Saint-Egrève Cedex
France
Tel: +33 (0)4 76 58 30 00
Hotline:
std-hotline@e2v.com
0833E–HIREL–01/07
e2v semiconductors SAS 2007