INDUCTORS
MLG0603S 0603 [0201 inch]*
MLG1005S 1005 [0402 inch]
MLG1608 1608 [0603 inch]
* Dimensions Code JIS[EIA]
July 2013
Inductors for High Frequency
Multilayer Ceramic
MLG series
(2/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
Inductors for High Frequency Circuits
Multilayer Ceramic
FEATURES
Advanced monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for High-
frequency.
APPLICATION
Smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners, automotive equipment
and other high frequency circuits for the mobile communication industry
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Overview of the MLG Series
MLG 0603 S 0N3 S T □□□
Series name L×W×H Dimensions Product internal
code
Inductance Inductance
tolerance Packaging style Internal code
(mm) (nH)
0603 0.6×0.3×0.3 B 1N1 1.1 B ±0.1nH T Taping
1005 1.0×0.5×0.5 S 11N 11 C ±0.2nH
1608 1.6×0.8×0.8 R10 100 S ±0.3nH
1R0 1000 D ±0.5nH
3%
5%
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
°C °C(pieces/reel) mg
MLG0603S –55 to +125 –55 to +125 15000 0.2
MLG1005S –55 to +125 –55 to +125 10000 1
MLG1608 –55 to +125 –55 to +125 4000 4
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
Overview of the MLG Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseries
MLG0603S Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
0.6±0.03
0.15±0.05 0.15±0.05
0.30±0.03 0.30±0.03
Dimensions in mm
0.3
0.3 0.250.25 Dimensions in mm
(6/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG0603S Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
 The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
0.3 ±0.1, ±0.2nH 100 10.0 20 up 0.1 0.02 600 MLG0603S0N3T□□□
0.4 ±0.1, ±0.2nH 100 10.0 20 up 0.1 0.02 600 MLG0603S0N4T□□□
0.5 ±0.1, ±0.2nH 100 10.0 20 up 0.1 0.02 600 MLG0603S0N5T□□□
0.6 ±0.1, ±0.2nH 100 10.0 20 up 0.1 0.02 600 MLG0603S0N6T□□□
0.7 ±0.1, ±0.2nH 100 10.0 16.3 0.1 0.02 600 MLG0603S0N7T□□□
0.8 ±0.1, ±0.2nH 100 10.0 16.1 0.1 0.03 600 MLG0603S0N8T□□□
0.9 ±0.1, ±0.2nH 100 10.0 13.8 0.1 0.03 600 MLG0603S0N9T□□□
1.0 ±0.1, ±0.2, 0.3nH 4100 10.0 14.4 0.1 0.04 600 MLG0603S1N0T□□□
1.1 ±0.1, ±0.2, 0.3nH 4 100 10.0 13.6 0.15 0.04 550 MLG0603S1N1T□□□
1.2 ±0.1, ±0.2, 0.3nH 4100 10.0 12.3 0.15 0.06 550 MLG0603S1N2T□□□
1.3 ±0.1, ±0.2, 0.3nH 4 100 9.0 11.4 0.15 0.07 550 MLG0603S1N3T□□□
1.5 ±0.1, ±0.2, 0.3nH 4100 9.0 10.4 0.15 0.07 550 MLG0603S1N5T□□□
1.6 ±0.1, ±0.2, 0.3nH 4 100 9.0 11.5 0.2 0.09 500 MLG0603S1N6T□□□
1.8 ±0.1, ±0.2, 0.3nH 4100 8.5 10.0 0.2 0.12 500 MLG0603S1N8T□□□
2.0 ±0.1, ±0.2, 0.3nH 4 100 8.2 9.8 0.25 0.14 400 MLG0603S2N0T□□□
2.2 ±0.1, ±0.2, 0.3nH 4100 8.0 8.9 0.25 0.14 400 MLG0603S2N2T□□□
2.4 ±0.1, ±0.2, 0.3nH 4 100 8.0 9.2 0.25 0.15 300 MLG0603S2N4T□□□
2.7 ±0.1, ±0.2, 0.3nH 4100 6.5 8.1 0.25 0.15 300 MLG0603S2N7T□□□
3.0 ±0.1, ±0.2, 0.3nH 4 100 6.2 7.8 0.3 0.20 300 MLG0603S3N0T□□□
3.3 ±0.1, ±0.2, 0.3nH 4100 5.8 7.0 0.35 0.23 300 MLG0603S3N3T□□□
3.6 ±0.1, ±0.2, 0.3nH 4 100 5.5 6.9 0.35 0.22 300 MLG0603S3N6T□□□
3.9 ±0.1, ±0.2, 0.3nH 5100 5.0 6.6 0.4 0.27 300 MLG0603S3N9T□□□
4.3 ±3%, ±0.3nH 5 100 5.0 6.4 0.4 0.27 300 MLG0603S4N3T□□□
4.7 ±3%, ±0.3nH 5100 4.5 5.4 0.45 0.28 300 MLG0603S4N7T□□□
5.1 ±3%, ±0.3nH 5 100 4.5 5.5 0.45 0.23 250 MLG0603S5N1T□□□
5.6 ±3%, ±0.3nH 5100 4.2 5.3 0.5 0.31 250 MLG0603S5N6T□□□
6.2 ±3%, ±0.3nH 5 100 4.2 5.1 0.55 0.32 250 MLG0603S6N2T□□□
6.8 ±3, ±5% 5100 3.6 4.4 0.6 0.32 250 MLG0603S6N8T□□□
7.5 ±3, ±5% 5 100 4.2 5.3 0.7 0.43 200 MLG0603S7N5T□□□
8.2 ±3, ±5% 5100 3.8 4.5 0.7 0.45 200 MLG0603S8N2T□□□
9.1 ±3, ±5% 5 100 3.4 4.9 0.8 0.51 200 MLG0603S9N1T□□□
10 ±3, ±5% 5100 3.2 4.1 0.8 0.53 200 MLG0603S10NT□□□
11 ±3, ±5% 6 100 3.0 3.7 0.8 0.53 200 MLG0603S11NT□□□
12 ±3, ±5% 6100 2.8 3.6 0.9 0.63 180 MLG0603S12NT□□□
13 ±3, ±5% 6 100 2.7 3.4 0.9 0.60 180 MLG0603S13NT□□□
15 ±3, ±5% 6100 2.5 3.3 1.1 0.69 180 MLG0603S15NT□□□
16 ±3, ±5% 6 100 2.3 3.0 1.1 0.70 180 MLG0603S16NT□□□
18 ±3, ±5% 6100 2.2 2.8 1.2 0.78 150 MLG0603S18NT□□□
20 ±3, ±5% 6 100 2.1 2.6 1.2 0.75 150 MLG0603S20NT□□□
22 ±3, ±5% 6100 2.0 2.5 1.2 0.88 150 MLG0603S22NT□□□
24 ±3, ±5% 6 100 1.9 2.3 1.3 0.90 150 MLG0603S24NT□□□
27 ±3, ±5% 6100 1.8 2.2 1.5 1.00 100 MLG0603S27NT□□□
30 ±3, ±5% 6 100 1.6 2.0 1.6 0.95 100 MLG0603S30NT□□□
33 ±3, ±5% 6100 1.6 2.0 1.8 1.20 100 MLG0603S33NT□□□
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(7/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG0603S Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
 The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
36 ±3, ±5% 6 100 1.5 1.8 2.0 1.68 50 MLG0603S36NT□□□
39 ±3, ±5% 6100 1.4 1.6 2.0 1.40 50 MLG0603S39NT□□□
43 ±3, ±5% 6 100 1.3 1.6 2.2 1.91 50 MLG0603S43NT□□□
47 ±3, ±5% 6100 1.3 1.5 2.2 1.48 50 MLG0603S47NT□□□
51 ±3, ±5% 5 100 1.2 1.5 2.8 1.98 50 MLG0603S51NT□□□
56 ±3, ±5% 5100 1.2 1.4 3.2 2.11 50 MLG0603S56NT□□□
62 ±3, ±5% 5 100 1.1 1.3 3.3 2.22 50 MLG0603S62NT□□□
68 ±3, ±5% 5100 1.05 1.24 3.5 2.40 50 MLG0603S68NT□□□
75 ±3, ±5% 5 100 0.95 1.17 3.8 2.67 50 MLG0603S75NT□□□
82 ±3, ±5% 5100 0.90 1.08 4.0 2.80 50 MLG0603S82NT□□□
91 ±3, ±5% 5 100 0.77 0.94 4.3 2.97 50 MLG0603S91NT□□□
100 ±3, ±5% 5100 0.77 0.94 4.5 3.13 50 MLG0603SR10T□□□
110 ±3, ±5% 5 100 0.77 0.94 6.5 5.24 50 MLG0603SR11T□□□
120 ±3, ±5% 5100 0.70 0.88 7.0 5.53 50 MLG0603SR12T□□□
130 ±3, ±5% 5 100 0.67 0.84 7.3 5.68 50 MLG0603SR13T□□□
150 ±3, ±5% 5100 0.64 0.77 8.0 6.24 50 MLG0603SR15T□□□
160 ±3, ±5% 5 100 0.60 0.73 8.3 6.67 50 MLG0603SR16T□□□
180 ±3, ±5% 5100 0.56 0.68 8.5 6.99 50 MLG0603SR18T□□□
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(8/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG0603S Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
 The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
0.3 0.3 0.3 0.3 0.3 14min. 18min. 29min. 32min. 35min. MLG0603S0N3T□□□
0.4 0.4 0.4 0.4 0.4 14min. 18min. 29min. 32min. 35min. MLG0603S0N4T□□□
0.5 0.5 0.5 0.5 0.5 14 18 29 32 35 MLG0603S0N5T□□□
0.6 0.6 0.5 0.5 0.5 16 20 33 34 39 MLG0603S0N6T□□□
0.7 0.6 0.6 0.6 0.6 16 21 33 35 39 MLG0603S0N7T□□□
0.7 0.7 0.7 0.7 0.7 15 20 32 34 38 MLG0603S0N8T□□□
0.8 0.8 0.8 0.8 0.8 15 19 30 32 35 MLG0603S0N9T□□□
0.9 0.9 0.9 0.9 0.9 14 18 29 30 34 MLG0603S1N0T□□□
1.0 1.0 1.0 1.0 1.0 14 19 29 31 34 MLG0603S1N1T□□□
1.1 1.1 1.1 1.1 1.1 14 18 29 30 34 MLG0603S1N2T□□□
1.2 1.2 1.2 1.2 1.2 14 18 29 30 33 MLG0603S1N3T□□□
1.4 1.4 1.4 1.4 1.4 15 19 29 30 34 MLG0603S1N5T□□□
1.5 1.5 1.5 1.5 1.5 14 18 29 30 33 MLG0603S1N6T□□□
1.7 1.7 1.7 1.7 1.7 15 19 29 30 33 MLG0603S1N8T□□□
1.9 1.9 1.9 1.9 1.9 14 18 28 29 32 MLG0603S2N0T□□□
2.1 2.0 2.1 2.1 2.1 14 18 27 28 31 MLG0603S2N2T□□□
2.2 2.2 2.2 2.3 2.3 14 18 27 29 32 MLG0603S2N4T□□□
2.5 2.5 2.6 2.6 2.7 15 19 28 29 31 MLG0603S2N7T□□□
2.8 2.8 2.9 2.9 3.0 15 19 29 31 33 MLG0603S3N0T□□□
3.1 3.1 3.2 3.3 3.4 15 19 28 29 31 MLG0603S3N3T□□□
3.4 3.4 3.5 3.6 3.7 14 18 26 27 29 MLG0603S3N6T□□□
3.7 3.7 3.8 3.9 4.1 15 19 29 29 32 MLG0603S3N9T□□□
4.1 4.1 4.3 4.4 4.6 14 18 27 27 29 MLG0603S4N3T□□□
4.4 4.4 4.8 4.9 5.2 15 20 28 29 30 MLG0603S4N7T□□□
4.8 4.8 5.1 5.3 5.6 14 18 25 26 27 MLG0603S5N1T□□□
5.3 5.3 5.7 5.9 6.4 16 20 27 28 29 MLG0603S5N6T□□□
5.9 5.9 6.5 6.8 7.5 15 18 25 25 26 MLG0603S6N2T□□□
6.4 6.5 7.4 7.8 8.7 15 19 26 26 25 MLG0603S6N8T□□□
7.1 7.1 7.8 8.0 8.7 14 18 25 26 26 MLG0603S7N5T□□□
7.8 7.8 8.8 9.3 10.4 15 18 24 24 24 MLG0603S8N2T□□□
8.6 8.6 9.8 10.3 11.5 14 17 22 22 22 MLG0603S9N1T□□□
10 10 12 12 15 15 18 23 22 21 MLG0603S10NT□□□
10 11 13 14 16 15 18 22 22 20 MLG0603S11NT□□□
11 12 14 15 19 16 19 24 23 20 MLG0603S12NT□□□
12 13 16 17 22 14 16 19 18 15 MLG0603S13NT□□□
14 15 20 23 33 15 19 20 18 14 MLG0603S15NT□□□
15 16 22 25 37 14 16 16 15 11 MLG0603S16NT□□□
17 18 28 35 14 17 15 13 MLG0603S18NT□□□
19 20 32 13 16 14 MLG0603S20NT□□□
21 23 40 15 17 13 MLG0603S22NT□□□
23 24 45 13 15 13 MLG0603S24NT□□□
27 29 15 17 MLG0603S27NT□□□
29 32 13 15 MLG0603S30NT□□□
33 36 14 16 MLG0603S33NT□□□
Product No. Manufacturer
4291B+16197A Agilent Technologies
(9/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG0603S Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
 The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
36 40 14 15 MLG0603S36NT□□□
40 47 13 14 MLG0603S39NT□□□
44 53 14 14 MLG0603S43NT□□□
49 60 13 13 MLG0603S47NT□□□
52 64 11 11 MLG0603S51NT□□□
59 77 12 11 MLG0603S56NT□□□
66 88 11 10 MLG0603S62NT□□□
74 104 13 11 MLG0603S68NT□□□
82 119 10 8MLG0603S75NT□□□
96 161 12 8 MLG0603S82NT□□□
109 9MLG0603S91NT□□□
129 11 MLG0603SR10T□□□
134 10 MLG0603SR11T□□□
156 9 MLG0603SR12T□□□
172 8MLG0603SR13T□□□
223 7 MLG0603SR15T□□□
238 7MLG0603SR16T□□□
318 6 MLG0603SR18T□□□
Product No. Manufacturer
4291B+16197A Agilent Technologies
(10/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG0603S Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
Measurement equipment
Equivalent measurement equipment may be used.
10 100 1000 10000
0
1000
100
10
1
Frequency(MHz)
Inductance(nH)
R18 R15
R12
R10
82N
68N
56N
47N 39N
33N
27N
22N 18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
Product No. Manufacturer
E4991A +16197A Agilent Technologies
(11/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG0603S Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
Measurement equipment
Equivalent measurement equipment may be used.
0
Q
10 100 1000 10000
Frequency(MHz)
10
20
30
40
50
R18
68N
56N
47N
39N
33N
27N
22N
18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
2N7
1N8
1N5
1N2
1N0
2N2
3N3
R12
R10
82N
R15
Product No. Manufacturer
E4991A +16197A Agilent Technologies
(12/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseries
MLG1005S Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
1.00±0.05
0.25±0.10 0.25±0.10
0.50±0.05 0.50±0.05
Dimensions in mm
0.5
0.5 0.4 0.5
(13/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1005S Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
* The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.*
(nH) Tolerance min. typ. max. typ.
0.3 ±0.1nH, ±0.2nH 100 10.0 20up 0.10 0.01 1000 MLG1005S0N3T□□□
0.4 ±0.1nH, ±0.2nH 100 10.0 20up 0.10 0.01 1000 MLG1005S0N4T□□□
0.5 ±0.1nH, ±0.2nH 100 10.0 20up 0.10 0.01 1000 MLG1005S0N5T□□□
0.6 ±0.1nH, ±0.2nH 100 10.0 20up 0.10 0.01 1000 MLG1005S0N6T□□□
0.7 ±0.1nH, ±0.2nH 100 10.0 18.7 0.10 0.02 1000 MLG1005S0N7T□□□
0.8 ±0.1nH, ±0.2nH 100 10.0 16.4 0.10 0.02 1000 MLG1005S0N8T□□□
0.9 ±0.1nH, ±0.2nH 100 10.0 17.7 0.10 0.04 1000 MLG1005S0N9T□□□
1.0 ±0.1nH, ±0.2, 0.3nH 7100 10.0 13.8 0.10 0.04 1000 MLG1005S1N0T□□□
1.1 ±0.1nH, ±0.2, 0.3nH 7 100 10.0 19.3 0.10 0.03 1000 MLG1005S1N1T□□□
1.2 ±0.1nH, ±0.2, 0.3nH 7100 10.0 11.6 0.10 0.04 1000 MLG1005S1N2T□□□
1.3 ±0.1nH, ±0.2, 0.3nH 7 100 8.00 11.7 0.10 0.04 1000 MLG1005S1N3T□□□
1.5 ±0.1nH, ±0.2, 0.3nH 7100 8.00 9.6 0.10 0.06 1000 MLG1005S1N5T□□□
1.6 ±0.1nH, ±0.2, 0.3nH 7 100 7.50 9.4 0.12 0.05 1000 MLG1005S1N6T□□□
1.8 ±0.1nH, ±0.2, 0.3nH 7100 8.00 10.3 0.15 0.06 900 MLG1005S1N8T□□□
2.0 ±0.1nH, ±0.2, 0.3nH 7 100 7.50 9.3 0.15 0.07 900 MLG1005S2N0T□□□
2.2 ±0.1nH, ±0.2, 0.3nH 7100 7.00 8.6 0.15 0.08 900 MLG1005S2N2T□□□
2.4 ±0.1nH, ±0.2, 0.3nH 7 100 7.00 8.2 0.15 0.08 800 MLG1005S2N4T□□□
2.7 ±0.1nH, ±0.2, 0.3nH 7100 6.00 7.3 0.15 0.08 800 MLG1005S2N7T□□□
3.0 ±0.1nH, ±0.2, 0.3nH 7 100 5.50 6.8 0.20 0.09 800 MLG1005S3N0T□□□
3.3 ±0.1nH, ±0.2, 0.3nH 8100 5.00 6.1 0.20 0.09 800 MLG1005S3N3T□□□
3.6 ±0.1nH, ±0.2, 0.3nH 8 100 5.00 6.7 0.20 0.09 700 MLG1005S3N6T□□□
3.9 ±0.1nH, ±0.2, 0.3nH 8100 5.00 6.5 0.20 0.11 700 MLG1005S3N9T□□□
4.3 ±0.2nH, ±0.3nH 8 100 4.50 6.0 0.20 0.11 700 MLG1005S4N3T□□□
4.7 ±0.2nH, ±0.3nH 8100 4.50 5.4 0.25 0.12 700 MLG1005S4N7T□□□
5.1 ±0.2nH, ±0.3nH 8 100 4.00 5.0 0.25 0.13 600 MLG1005S5N1T□□□
5.6 ±0.2nH, ±0.3nH 8100 4.00 5.3 0.25 0.14 600 MLG1005S5N6T□□□
6.2 ±3%, ±0.3nH 8 100 4.00 4.7 0.25 0.16 600 MLG1005S6N2T□□□
6.8 ±3%, ±5% 8100 3.50 4.4 0.25 0.15 600 MLG1005S6N8T□□□
7.5 ±3%, ±5% 8 100 3.00 4.1 0.25 0.15 500 MLG1005S7N5T□□□
8.2 ±3%, ±5% 8100 3.00 4.0 0.30 0.19 500 MLG1005S8N2T□□□
9.1 ±3%, ±5% 8 100 3.00 3.8 0.30 0.20 500 MLG1005S9N1T□□□
10 ±3%, ±5% 8100 2.50 3.4 0.35 0.22 500 MLG1005S10NT□□□
11 ±3%, ±5% 8 100 2.50 3.5 0.40 0.28 400 MLG1005S11NT□□□
12 ±3%, ±5% 8100 2.50 3.0 0.40 0.25 400 MLG1005S12NT□□□
13 ±3%, ±5% 8 100 2.40 2.9 0.50 0.26 400 MLG1005S13NT□□□
15 ±3%, ±5% 8100 2.20 2.8 0.55 0.35 400 MLG1005S15NT□□□
16 ±3%, ±5% 8 100 2.10 2.7 0.55 0.32 400 MLG1005S16NT□□□
18 ±3%, ±5% 8100 2.00 2.5 0.60 0.40 350 MLG1005S18NT□□□
20 ±3%, ±5% 8 100 1.90 2.4 0.60 0.38 350 MLG1005S20NT□□□
22 ±3%, ±5% 8100 1.70 2.2 0.70 0.46 350 MLG1005S22NT□□□
24 ±3%, ±5% 8 100 1.70 2.1 0.70 0.43 350 MLG1005S24NT□□□
27 ±3%, ±5% 8100 1.60 2.0 0.80 0.53 300 MLG1005S27NT□□□
30 ±3%, ±5% 8 100 1.50 1.9 0.80 0.50 300 MLG1005S30NT□□□
Measurement item Product No. Manufacturer
L, Q 4291B +16193A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(14/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1005S Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
* The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.*
(nH) Tolerance min. typ. max. typ.
33 ±3%, ±5% 8 100 1.40 1.8 0.90 0.59 300 MLG1005S33NT□□□
36 ±3%, ±5% 8100 1.30 1.7 1.00 0.62 250 MLG1005S36NT□□□
39 ±3%, ±5% 8 100 1.20 1.6 1.00 0.65 250 MLG1005S39NT□□□
43 ±3%, ±5% 8100 1.20 1.6 1.10 0.67 250 MLG1005S43NT□□□
47 ±3%, ±5% 8 100 1.10 1.4 1.20 0.75 250 MLG1005S47NT□□□
51 ±3%, ±5% 8100 1.10 1.5 1.20 0.72 250 MLG1005S51NT□□□
56 ±3%, ±5% 8 100 1.00 1.3 1.30 0.83 200 MLG1005S56NT□□□
62 ±3%, ±5% 8100 1.00 1.3 1.40 0.85 200 MLG1005S62NT□□□
68 ±3%, ±5% 8 100 0.80 1.1 1.50 0.87 200 MLG1005S68NT□□□
75 ±3%, ±5% 8100 0.75 1.1 1.50 0.93 200 MLG1005S75NT□□□
82 ±3%, ±5% 8 100 0.70 1.0 1.60 1.01 200 MLG1005S82NT□□□
91 ±3%, ±5% 8100 0.70 0.9 1.80 1.14 200 MLG1005S91NT□□□
100 ±3%, ±5% 8 100 0.70 0.9 2.00 1.37 200 MLG1005SR10T□□□
110 ±3%, ±5% 8100 0.70 0.9 2.20 1.48 150 MLG1005SR11T□□□
120 ±3%, ±5% 8 100 0.60 0.8 2.20 1.48 150 MLG1005SR12T□□□
130 ±3%, ±5% 8100 0.60 0.8 2.50 1.68 150 MLG1005SR13T□□□
150 ±3%, ±5% 8 100 0.55 0.7 3.50 2.44 150 MLG1005SR15T□□□
160 ±3%, ±5% 8100 0.50 0.6 3.80 2.74 150 MLG1005SR16T□□□
180 ±3%, ±5% 8 100 0.50 0.6 3.80 2.88 150 MLG1005SR18T□□□
200 ±3%, ±5% 8100 0.42 0.5 4.20 3.15 100 MLG1005SR20T□□□
220 ±3%, ±5% 8 100 0.45 0.5 4.20 3.02 100 MLG1005SR22T□□□
240 ±3%, ±5% 8100 0.40 0.5 4.80 3.42 100 MLG1005SR24T□□□
270 ±3%, ±5% 8 100 0.40 0.5 4.80 3.54 100 MLG1005SR27T□□□
300 ±3%, ±5% 650 0.35 0.4 6.50 4.82 50 MLG1005SR30T□□□
330 ±3%, ±5% 6 50 0.35 0.4 7.00 5.21 50 MLG1005SR33T□□□
360 ±3%, ±5% 650 0.30 0.4 7.50 5.39 50 MLG1005SR36T□□□
390 ±3%, ±5% 6 50 0.30 0.4 8.00 5.97 50 MLG1005SR39T□□□
Measurement item Product No. Manufacturer
L, Q 4291B +16193A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(15/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1005S Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
 The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
0.3 0.3 0.3 0.3 0.3 22min. 27min. 46min. 49min. 53min. MLG1005S0N3 T□□□
0.4 0.4 0.4 0.4 0.4 22min. 27min. 46min. 49min. 53min. MLG1005S0N4 T□□□
0.5 0.5 0.5 0.5 0.5 22min. 27min. 46min. 49min. 53min. MLG1005S0N5 T□□□
0.6 0.6 0.6 0.6 0.6 22 27 46 49 53 MLG1005S0N6 T□□□
0.7 0.7 0.7 0.7 0.7 22 28 45 49 54 MLG1005S0N7 T□□□
0.8 0.8 0.8 0.8 0.8 26 34 57 60 66 MLG1005S0N8 T□□□
0.9 0.8 0.8 0.8 0.8 21 27 44 47 53 MLG1005S0N9 T□□□
0.9 0.9 0.9 0.9 0.9 22 29 48 50 56 MLG1005S1N0 T□□□
1.0 1.0 1.0 1.0 1.0 23 29 47 50 57 MLG1005S1N1 T□□□
1.1 1.1 1.1 1.1 1.1 23 29 48 50 56 MLG1005S1N2 T□□□
1.2 1.2 1.2 1.2 1.2 22 27 44 47 53 MLG1005S1N3 T□□□
1.4 1.4 1.4 1.5 1.5 23 29 47 50 56 MLG1005S1N5 T□□□
1.5 1.5 1.5 1.6 1.6 23 29 46 49 54 MLG1005S1N6 T□□□
1.7 1.7 1.7 1.7 1.7 20 26 41 43 49 MLG1005S1N8 T□□□
1.9 1.9 1.9 1.9 1.9 21 25 41 43 48 MLG1005S2N0 T□□□
2.1 2.1 2.1 2.1 2.2 22 27 44 47 52 MLG1005S2N2 T□□□
2.3 2.3 2.3 2.3 2.4 21 26 42 44 49 MLG1005S2N4 T□□□
2.6 2.6 2.6 2.7 2.7 22 27 43 45 50 MLG1005S2N7 T□□□
2.9 2.9 3.0 3.0 3.1 24 29 47 49 54 MLG1005S3N0 T□□□
3.2 3.2 3.3 3.4 3.5 24 30 46 48 53 MLG1005S3N3 T□□□
3.4 3.4 3.6 3.6 3.8 21 26 40 42 46 MLG1005S3N6 T□□□
3.7 3.7 3.9 3.9 4.1 22 28 43 45 50 MLG1005S3N9 T□□□
4.1 4.1 4.3 4.4 4.6 24 30 47 49 53 MLG1005S4N3 T□□□
4.5 4.5 4.8 4.9 5.2 23 30 45 47 50 MLG1005S4N7 T□□□
4.9 4.9 5.4 5.6 6.1 23 29 42 43 44 MLG1005S5N1 T□□□
5.4 5.4 5.8 5.9 6.3 22 28 42 43 45 MLG1005S5N6 T□□□
6.0 6.0 6.8 7.1 7.8 24 29 42 43 43 MLG1005S6N2 T□□□
6.5 6.6 7.4 7.8 8.6 23 28 40 41 41 MLG1005S6N8 T□□□
7.2 7.4 8.6 9.2 10.5 24 30 41 41 39 MLG1005S7N5 T□□□
7.9 8.0 9.3 9.9 11.3 23 28 38 38 36 MLG1005S8N2 T□□□
8.8 9.0 10.8 11.6 13.7 24 30 40 39 36 MLG1005S9N1 T□□□
9.7 9.9 12.4 13.5 16.7 24 30 37 36 31 MLG1005S10N T□□□
10.6 10.9 13.8 15.1 19.0 23 28 34 33 28 MLG1005S11N T□□□
11.7 12.1 16.2 18.3 23 29 33 31 MLG1005S12N T□□□
12.6 13.0 18.3 21.3 20 24 25 22 MLG1005S13N T□□□
14.7 15.3 22.0 26.0 23 28 29 26 MLG1005S15N T□□□
15.6 16.2 24.1 29.0 22 26 26 22 MLG1005S16N T□□□
17.7 18.6 29.0 23 28 26 MLG1005S18N T□□□
19.7 20.8 36.8 21 25 21 MLG1005S20N T□□□
21.8 23.3 22 27 MLG1005S22N T□□□
23.8 25.5 22 26 MLG1005S24N T□□□
27.0 29.6 20 23 MLG1005S27N T□□□
30.1 33.5 19 21 MLG1005S30N T□□□
Product No. Manufacturer
4291B +16193A Agilent Technologies
(16/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1005S Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
 The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
33.5 37.8    20 23    MLG1005S33N T□□□
36.7 41.5 21 23 MLG1005S36N T□□□
40.3 46.9
    20 21     MLG1005S39N T□□□
44.3 51.6 20 21 MLG1005S43N T□□□
50.2 63.2
    19 20     MLG1005S47N T□□□
53.7 65.6 19 19 MLG1005S51N T□□□
60.9 80.2
    19 18     MLG1005S56N T□□□
67.5 89.8 18 16 MLG1005S62N T□□□
75.8 107.5     17 15     MLG1005S68N T□□□
86.5 135.2 17 13 MLG1005S75N T□□□
96.9     16    MLG1005S82N T□□□
111.0 15 MLG1005S91N T□□□
128.9     14    MLG1005SR10 T□□□
140.8 15 MLG1005SR11 T□□□
175.2      12    MLG1005SR12 T□□□
187.8 13 MLG1005SR13 T□□□
284.7      11      MLG1005SR15 T□□□
MLG1005SR16 T□□□
          MLG1005SR18 T□□□
MLG1005SR20 T□□□
          MLG1005SR22 T□□□
MLG1005SR24 T□□□
        MLG1005SR27 T□□□
MLG1005SR30 T□□□
          MLG1005SR33 T□□□
MLG1005SR36 T□□□
          MLG1005SR39 T□□□
Product No. Manufacturer
4291B +16193A Agilent Technologies
(17/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1005S Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
Measurement equipment
Equivalent measurement equipment may be used.
10 100 1000 10000
0
1000
100
10
1
Frequency(MHz)
Inductance(nH)
R39 R18
R15
68N
15N
12N
10N
8N2
6N8
1N2
1N0
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
18N
56N
47N
39N
33N
27N
22N
82N
R12
R27
R22 R10
R33
Product No. Manufacturer
E4991A +16193A Agilent Technologies
(18/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1005S Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
Measurement equipment
Equivalent measurement equipment may be used.
0
Q
10 100 1000 10000
Frequency(MHz)
10
20
30
40
50
60
70
R39
R18
R15
68N
15N
12N
10N
8N2
6N8
1N2
1N0
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
18N
56N
47N
39N
33N
27N
22N
82N
R12
R33
R27
R22
R10
Product No. Manufacturer
E4991A +16193A Agilent Technologies
(19/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseries
MLG1608Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
1.60±0.15
0.30±0.20 0.30±0.20
0.80±0.15 0.80±0.15
Dimensions in mm
0.8
0.6 0.8 0.6
(20/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1608 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
* The " □□□ " of the Part Number contains the internal code.
Because it provides for a product of smaller inductance tolerance, please refer.
Measurement equipment
Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
1 ±0.3nH 8 100 10.0 20up 0.10 0.03 600 MLG1608B1N0ST□□□
1.2 ±0.3nH 8100 10.0 20up 0.10 0.04 600 MLG1608B1N2ST□□□
1.5 ±0.3nH 8 100 10.0 19.6 0.10 0.03 600 MLG1608B1N5ST□□□
1.8 ±0.3nH 8100 10.0 16.6 0.10 0.04 600 MLG1608B1N8ST□□□
2.2 ±0.3nH 10 100 8.0 10.8 0.10 0.05 600 MLG1608B2N2ST□□□
2.7 ±0.3nH 10 100 7.0 8.8 0.12 0.06 600 MLG1608B2N7ST□□□
3.3 ±0.3nH 10 100 6.5 8.8 0.12 0.06 600 MLG1608B3N3ST□□□
3.9 ±0.3nH 10 100 6.0 7.9 0.14 0.06 600 MLG1608B3N9ST□□□
4.7 ±0.3nH 10 100 5.0 6.8 0.15 0.08 600 MLG1608B4N7ST□□□
5.6 ±0.5nH 10 100 5.0 6.8 0.16 0.08 600 MLG1608B5N6DT□□□
6.8 ±0.5nH 10 100 4.5 5.7 0.18 0.10 600 MLG1608B6N8DT□□□
8.2 ±0.5nH 10 100 4.5 5.6 0.20 0.10 600 MLG1608B8N2DT□□□
10 ±5% 12 100 3.5 4.5 0.20 0.11 600 MLG1608B10NJT□□□
12 ±5% 12 100 3.0 3.8 0.25 0.13 600 MLG1608B12NJT□□□
15 ±5% 12 100 2.8 3.6 0.28 0.14 600 MLG1608B15NJT□□□
18 ±5% 12 100 2.6 3.3 0.32 0.16 600 MLG1608B18NJT□□□
22 ±5% 12 100 2.3 3.0 0.35 0.19 500 MLG1608B22NJT□□□
27 ±5% 12 100 2.0 2.7 0.40 0.21 500 MLG1608B27NJT□□□
33 ±5% 12 100 1.8 2.3 0.50 0.25 500 MLG1608B33NJT□□□
39 ±5% 12 100 1.6 2.0 0.55 0.26 400 MLG1608B39NJT□□□
47 ±5% 14 100 1.4 1.8 0.60 0.35 400 MLG1608B47NJT□□□
56 ±5% 14 100 1.2 1.8 0.70 0.41 400 MLG1608B56NJT□□□
68 ±5% 14 100 1.1 1.6 0.75 0.43 300 MLG1608B68NJT□□□
82 ±5% 14 100 1.0 1.4 0.80 0.50 300 MLG1608B82NJT□□□
100 ±5% 14 100 0.80 1.2 1.00 0.64 300 MLG1608BR10JT□□□
120 ±5% 14 100 0.65 0.8 1.20 0.89 300 MLG1608SR12JT□□□
150 ±5% 14 100 0.55 0.7 1.30 1.03 250 MLG1608SR15JT□□□
180 ±5% 14 100 0.50 0.6 1.40 1.08 250 MLG1608SR18JT□□□
220 ±5% 14 100 0.45 0.6 1.70 1.29 200 MLG1608SR22JT□□□
270 ±5% 14 100 0.35 0.5 2.00 1.59 200 MLG1608SR27JT□□□
330 ±5% 10 50 0.35 0.47 2.80 1.90 100 MLG1608SR33JT□□□
390 ±5% 10 50 0.30 0.43 3.00 2.06 100 MLG1608SR39JT□□□
470 ±5% 10 50 0.25 0.39 3.50 2.47 100 MLG1608SR47JT□□□
560 ±5% 10 50 0.25 0.36 4.50 3.20 70 MLG1608SR56JT□□□
680 ±5% 10 50 0.20 0.31 5.50 3.88 70 MLG1608SR68JT□□□
820 ±5% 10 50 0.15 0.22 5.50 3.76 70 MLG1608SR82JT□□□
1000 ±5% 10 50 0.13 0.19 5.50 4.27 70 MLG1608S1R0JT□□□
Measurement item Product No. Manufacturer
L, Q 4291B +16193A Agilent Technologies
Self-resonant frequency 8720C Panasonic
DC resistance Type-7561 Yokogawa
(21/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1608 Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
 The " □□□ " of the Part Number contains the internal code.
Because it provides for a product of smaller inductance tolerance, please refer.
Measurement equipment
Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
1.0 1.0 1.0 1.0 1.0 39 48 77 82 95 MLG1608B1N0ST□□□
1.2 1.1 1.2 1.2 1.2 28 35 57 60 68 MLG1608B1N2ST□□□
1.5 1.5 1.5 1.5 1.5 37 48 78 81 93 MLG1608B1N5ST□□□
1.8 1.8 1.8 1.8 1.8 38 48 77 81 95 MLG1608B1N8ST□□□
2.2 2.1 2.2 2.2 2.2 44 54 88 91 107 MLG1608B2N2ST□□□
2.6 2.6 2.7 2.7 2.8 40 51 79 81 94 MLG1608B2N7ST□□□
3.2 3.2 3.3 3.3 3.4 38 48 76 79 91 MLG1608B3N3ST□□□
3.8 3.8 4.0 4.0 4.1 40 50 79 81 93 MLG1608B3N9ST□□□
4.6 4.6 4.9 5.0 5.2 41 51 76 79 88 MLG1608B4N7ST□□□
5.4 5.5 5.8 5.9 6.2 37 46 69 71 79 MLG1608B5N6DT□□□
6.6 6.7 7.3 7.5 8.0 38 47 67 68 74 MLG1608B6N8DT□□□
8.0 8.1 8.9 9.3 10 39 48 67 68 71 MLG1608B8N2DT□□□
9.8 10.0 11.5 12.1 13.6 38 47 63 63 61 MLG1608B10NJT□□□
11.8 12.1 14.8 16.0 19.3 39 48 59 57 51 MLG1608B12NJT□□□
14.8 15.4 20.6 23.4 38 46 49 46 MLG1608B15NJT□□□
17.8 18.5 25.5 29.3 36 44 47 42 MLG1608B18NJT□□□
21.9 22.9 33.6 40.2 36 44 43 38 MLG1608B22NJT□□□
27.1 28.8 50.6 37 43 34 MLG1608B27NJT□□□
33.4 36.0 37 43 MLG1608B33NJT□□□
40.2 45.0 36 40 MLG1608B39NJT□□□
49.1 56.0 38 41 MLG1608B47NJT□□□
59.6 71.1 37 38 MLG1608B56NJT□□□
74.0 92.8 34 33 MLG1608B68NJT□□□
91.1 120.6 33 31 MLG1608B82NJT□□□
118 35 MLG1608BR10JT□□□
188 23 MLG1608SR12JT□□□
MLG1608SR15JT□□□
MLG1608SR18JT□□□
MLG1608SR22JT□□□
MLG1608SR27JT□□□
MLG1608SR33JT□□□
MLG1608SR39JT□□□
MLG1608SR47JT□□□
MLG1608SR56JT□□□
MLG1608SR68JT□□□
MLG1608SR82JT□□□
MLG1608S1R0JT□□□
Product No. Manufacturer
4291B +16193A Agilent Technologies
(22/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1608Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
Measurement equipment
Equivalent measurement equipment may be used.
Product No. Manufacturer
E4991A +16193A Agilent Technologies
(23/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseriesMLG1608Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
Measurement equipment
Equivalent measurement equipment may be used.
0
Q
10 100 1000 10000
Frequency(MHz)
10
20
30
40
50
60
70
80
90
100
1R0 R82
R68 R27
R15
R12
R10 82N
68N
56N
39N
33N
27N
22N
18N
15N
12N
10N
8N2
5N6
4N7
3N3
2N2
1N2
1N0
47N
R18
R22
3N9
1N5
2N7
1N8
6N8
R56
R47
R39
R33
Product No. Manufacturer
E4991A +16193A Agilent Technologies
(24/24)
INDUCTORS
001-01 / 20130717 / inductor_high-frequency_mlg_en.fm
• All specifications are subject to change without notice.
MLGseries
Packaging Style
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
8.0±0.3 3.5±0.05
1.75±0.1
4.0±0.1
1.5 +0.1
–0.0
Sprocket hole Cavity
C
A B
2.0±0.05 2.0±0.05
160min. Taping 200min.
300min.
Drawing direction
Dimensions in mm
Type A B C
MLG0603S 0.5 max. 0.38±0.05 0.68±0.05
MLG1005S 0.8 max. 0.62±0.1 1.12±0.1
MLG1608 1.1 max. 1.1±0.2 1.9±0.2