TD62S350AFM
2001-12-05
1
TOSHIBA Bipo lar Digital Integrat ed Circuit
Silicon Mo nolith ic
TD62S350AFM
1-Channel Darlington Source-Current Driver
The TD62S350AFM is a 1-channel noninverting source-current
driver. The driver incorporates an input resistor which limits
output pull-down resistance and base current.
The driver is optimal for driving fluorescent display tubes and
LEDs.
When using the driver, pay attention to the thermal conditions.
Features
• Ultra-small HSON6 package with heat sink on rear
• Large output voltage: VOUT = −50 V (min)
• Large output current: IOUT = −500 mA (max)
• Built-in input resistor: RIN = 10 kΩ
• Input signal: High Level Active
Pin Connection (t op view) Basic Circuit Diagram
Note 1: Diodes shown using dotted lines are parasitic. Do not use them.
Note 2: W hen using the driver, connect the OUTPUT pin to the TEST pin.
Note 3: When using the driver, connect the P-GND pin to the heat sink on the rear of the package.
Weight: 0.017 g (typ.)
10 kΩ
2.6 kΩ
INPUT
20 kΩ
10 kΩ
VCC
TEST
OUTPUT
P-GND
Rpd
5 kΩ
1
2
3
INPUT
P-GND
NC
6
5
4
OUTPUT
TEST
VCC
TD62S350AFM
2001-12-05
2
Maximum Ratings (Ta =
==
= 25°C)
Characteristics Symbol Rating Unit
Supply volt age VCC −0.5~50 V
Output voltage VOUT 50 V
Collect or-em it t er volt age VCEO 50 V
Output current IOUT −500 mA
Input volt age VIN −0.5~15 V
Power dissipation PD (Note 4) 0.78 W
Rth (j-a)
(Note 4) 160
Saturated thermal resistance Rth (j-c)
(Note 5) 25 °C/W
Operating temperature Topr −40~85 °C
Storage temperature Tstg −55~150 °C
Note 4: 114.3 × 76.2 × 1.6 mm glass epoxy film substrate Cu heat dissipation pattern 100 mm2
Note 5: When an infinite heat sink is m ounte d.
Recommended Operating Condition (Ta =
==
= −
−−
−40~85°C)
Characteristics Symbol Test Condition Min Typ. Max Unit
Supply volt age VCC 50 V
Output current IOUT Ta = 60°C, Tj = 105°C −130 mA
Input volt age VIN 12 V
Output ON VIN (ON) 2.0 5.0 12
Input volt age Output OFF VIN (OFF) 0 0.8 V
Electrical Characteristics (Ta =
==
= 25°C, VCC =
==
= 50 V)
Characteristics Symbol
Test
Circuit Test Condition Min Typ. Max Unit
Output leakage current ICEX 1 VIN = 0. 4 V 10 µA
VIN = 2.0 V, IOUT = −350 mA 1.8 2.0
Output saturation voltage VCE (sat) 2
VIN = 2.0 V, IOUT = −130 mA 1.5 1.75 V
VIN = 3.6 V 240 350 µA
Input current IIN ( O N) 3
VIN = 12 V 1.1 1.6 mA
VIN (ON) V
CE = 2.0 V, IOUT = −350 mA 2.0
Input volt age VIN (OFF) 4 IOUT = −500 µA 0.5 V
Power dissipation ICC (ON) 3 VIN = 5 V 0.8 mA
Output pulldown resistor Rpd 168 240 312 kΩ
Turn-on delay tON 0.1
Turn-off delay tOFF 5 RL = 125 Ω, CL = 15 pF 7.0 µs
TD62S350AFM
2001-12-05
3
Test Circuit
1. ICEX 2. VCE (sat)
3. IIN (ON), ICC 4. VIN (ON), VIN (OFF)
5. tON, tOFF
Note 6: Pulse width 50 µs, Duty cycle 10%
Output impedance 50 Ω, tr<
=
5 ns, tf<
=
10 ns
Note 7: CL includes probe and jig capacitance.
ICEX
VCC
VIN
VCC
VIN
VCE
(
sat
)
IOUT
ICC
VCC
VIN
IIN
(
ON
)
VCC
VIN (ON)
VIN (OFF)
VCE
IOUT
Pulse
generator
INPUT
CL (Note 7)
(Note 6)
VCC
RL
10%
90%90%
10% 10%
50% 50%
tON t
OFF
tf tr
5 V
0
VOH
VOL
OUTPUT
INPUT
90%
50 µs
Caution on Application
1. The device does not include protectors such as an overcurrent protector and an overvoltage protector.
Applying excessive current or voltage may damage the device.
Thus, design with great care to prevent excessive current or voltage from being applied to the device.
The device may also be damaged by short-circuits between outputs and power supply/ground.
Take care when designing output, VCC and GND line.
2. If the TD62S350AFM is used to drive an inductive load (such as a motor, solenoid, or relay), Toshiba
recommends that the diodes be connected between pin 1 and pin 5 so as to absorb the counter
electromotive force generated by the load.
Please adhere to the maximum ratings of this device.
3. Be sure to mount the device in the correct orientation. Make sure that the positive and negative
power supply pins are connected the right way round. Otherwise, the absolute maximum current
and power dissipation ratings may be exceeded and the device may break down or undergo
performance degradation, causing it to catch fire or explode, and resulting in injury.
TD62S350AFM
2001-12-05
4
Package Dimensions
Weight: 0.017 g (typ.)
TD62S350AFM
2001-12-05
5
Preliminary land pattern
Preliminary PCB trace dimension
2.2 0.6 0.6
1.6
1.6
0.7 0.7 0.7
0.25
1.3
Unit : mm
5 mm
10 mm
TD62S350AFM
2001-12-05
6
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc. .
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.
• The products described in this document are subject to the foreign exchange and foreign trade laws.
• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.
• The information contained herein is subject to change without notice.
000707EB
A
RESTRICTIONS O N PRODUCT USE
