HIGH FLUX LED ILLUMINATORS OTLXXXA-5-10-66-E PRODUCT DESCRIPTION The OTLXXXA-5-10-66-E is a series of high flux LED based illuminators with blue (470nm), green (530nm), amber (590nm), red (630nm), and white visible emission. The blue, green, and white illuminators utilize InGaN LED's and the amber and red utilize AlInGaP LED's. The LED's are mounted on a BeO substrate that is attached to a TO-66 power package to ensure high reliability through efficient heat transfer. These illuminators are intended for use in high luminous, hard to access applications such as Aerospace Lighting, Emergency & Signal Lighting, Hazardous Lighting, Electronic Signs, and General Industrial Lighting and Illumination. ILLUMINATOR PART NUMBER GUIDE PART NUMBER COLOR DOMINANT WAVELENGTH TYPICAL INITIAL STATIC LUMINOUS FLUX (TYP D, nm) ( TYP V, lm, TJ = 25 C ) OTL470A-5-10-66-E BLUE 470 9.5 (IF = 300 mA) OTL530A-5-10-66-E GREEN 530 42 (IF = 300 mA) OTL590A-5-10-66-E AMBER 590 53 OTL630A-5-10-66-E RED 625 55 (IF = 800 mA) OTLWHTA-5-10-66-E WHITE N/A 42 (IF = 300 mA) (IF = 800 mA) ABSOLUTE MAXIMUM RATINGS (TJ = 25C) Power Dissipation Red (Derate 330 mW/C above 85C): Amber (Derate 300 mW/C above 81C): Blue, Green, White (Derate 240 mW/C above 76C): Static Forward Current 9.0 W 5W Red, Amber: 800 mA Blue, Green, White: 300 mA Peak Forward Current Red: Amber: ( Pulse Width 10 ms and Duty Cycle 10%) Blue, Green, White: Reverse Leakage (Vr = 20 Volts) 8W 4A 2.5 A 2A IR 100 uA Lead Soldering Temperature 240 C for 10 seconds OPTO TECHNOLOGY, INC. 562 Chaddick Drive, Wheeling, IL 60090 Phone: (847) 537-4277 FAX: (847) 537-4785 Website: www.optotech.com DATA SHEET REV. B (9/14/01) Page 1 of 4 HIGH FLUX LED ILLUMINATORS OTLXXXA-5-10-66-E INITIAL ELECTRO-OPTICAL CHARACTERISTICS at TJ = 25C, IF = 200 mA TYPE LUMINOUS FLUX RADIANT FLUX ( V, lm) (Factor,Pe, uW) FORWARD VOLTAGE DOMINANT WAVELENGTH [PEAK] WAVELENGTH FULL WIDTH HALF MAXIMUM (VF, V) ( D [ P], nm, CIE x,y ) ( , nm) (Calculated) MIN TYP Factor 7.0 51.5 lm/W @ 465nm 16.06 588 lm/W @ 530nm 16.6 516 lm/W @ 590nm 9.7 181 lm/W @ 630 9.3 BLUE 34.0 GREEN 18.4 AMBER 14.4 RED 31.0 WHITE -------- TYP TYP MAX MIN TYP MAX TYP 465 470/ [466] 475 35 540 45 x = 0.13 y = 0.07 520 530 / [525] x = 0.19 y = 0.70 590 / [592] 20 x = 0.57 y = 0.42 625 / [630] 20 x = 0.69 y = 0.31 -------- 16.06 x = 0.32 N/A y = 0.33 THERMAL PARAMETERS Operating Temperature -40 C to +100 C Maximum Junction Temperature Red: 110 C Amber, Green, Blue White: 100 C Typical Junction to Still Air Thermal Resistance, RTHJA 65 C/W Typical Junction to Case Thermal Resistance, RTHJC Amber, Red: 3.3 C/W Blue, Green, White: 4.0 C/W OPTICAL PARAMETERS Viewing Angle ( 1/2 ) 54 degrees typical Total Beam Width 78 degrees typical ELECTRICAL PARAMETERS (Typical at TJ = 25C) Parameter Conditions Red Capacitance, Junction Cj0 Capacitance, Case to Pin Rise Time, Electrical Fall Time, Electrical Vd = 0 volts -Rsource = 66 ohm, If = 200 mA Rsource = 66 ohm, If = 200 mA OPTO TECHNOLOGY, INC. Amber Green 61 pF 8 pF 6.6 nSec 74 pF 8 pF 10.4 nSec 69 pF 8 pF 12 nSec Blue / White 68 pF 8 pF 9.2 nSec 20 nSec 9.6 nSec 13 nSec 9.4 nSec 562 Chaddick Drive, Wheeling, IL 60090 Phone: (847) 537-4277 FAX: (847) 537-4785 Website: www.optotech.com DATA SHEET REV. B (9/14/01) Page 2 of 4 HIGH FLUX LED ILLUMINATORS OTLXXXA-5-10-66-E Therm al Derating w ith Infinite Heat Sink 10.00 9.00 470/530/White Power Watts 8.00 7.00 590 630 6.00 5.00 4.00 No Heat Sink 3.00 2.00 1.00 0.00 0.00 50.00 100.00 Case Tem p Pow er Output vs. Forw ard Current 0.9 0.8 0.7 630 0.6 0.5 0.4 0.3 530 590 470/ White 0.2 0.1 0.0 8.5 60.0 Luminous Flux (lm) Current (A) Current vs. Forw ard Voltage (Typical) 10.5 12.5 14.5 16.5 18.5 630 30.0 590 20.0 530 White 10.0 470 Relative Power Output (%) 0.9 0.8 0.7 630 0.6 590 0.5 530 0.4 White 0.3 470 0.2 0.1 450 550 650 0.20 0.40 0.60 Forw ard Current (A) 0.80 Average Radiation Pattern Spectral Output 1.0 Normalized Intensity 40.0 0.0 0.00 Forward Voltage (V) 0.0 350 50.0 100 90 80 70 60 50 40 30 20 10 0 -90 750 -30 0 30 60 Beam Angle ( Degrees) Wavelength (nm ) OPTO TECHNOLOGY, INC. -60 562 Chaddick Drive, Wheeling, IL 60090 Phone: (847) 537-4277 FAX: (847) 537-4785 Website: www.optotech.com DATA SHEET REV. B (9/14/01) Page 3 of 4 90 HIGH FLUX LED ILLUMINATORS OTLXXXA-5-10-66-E EYE SAFETY ISSUES Currently, the LED industry has no universally agreed upon standard to cover eye safety issues associated with the use of LED products. The closest is CEI/IEC 60825-1, used in Europe, which was originally developed for lasers. It was later amended to include LED's, but some in the industry have reservations as to the applicability of this standard to LED's. Under this standard, the OTL470A-5-10-66-E (430nm) and OTL530A-5-10-66-E (530nm) are class 2 LED products and carry the warning: LED RADIATION DO NOT STARE INTO BEAM (for 470nm and 530nm Sharks) CLASS 2 LED PRODUCT For the OTL590A-5-10-66-E (amber) and the OTL630A-5-10-66-E (red), the standard rates them as a class 1 LED product and requires the explanatory label: CLASS 1 LED PRODUCT (for 590nm and 630nm Sharks) Handling and Other Precautions These parts are high power devices and as such are intended to be used with a heatsink. Devices operated without proper heat sink conditions, or proper current limiting will reach hazardous temperatures very quickly. Do not operate devices under these conditions under any circumstances. These parts contain a Beryllia ceramic substrate. Beryllia ceramic, in solid form and as contained in finished products presents no special health risks. Warning: Overexposure to beryllium by inhalation may cause chronic beryllium disease, a chronic lung disease, and cancer. Therefore; processing or recycling using (for example) grinding, melting, welding, or sawing, of this device or as contained in a final assembly may produce airborne dust, fumes, or mists and therefore the use of exhaust ventilation or other controls should be used to prevent exposure to workers. Electro-Static-Discharge Any semiconductor circuit can be damaged by ESD. OPTO TECHNOLOGY INC. recommends that all LED circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage to the component. ESD damage can range from subtle performance degradation to complete device failure. Silicone Overcoat The OTLXXXA-5-10-66-E series components have a silicone overcoat, which is soft and flexible (40 durometer, Shore A) and should not be immersed or cleaned with water, alcohol, or other chemical solvents or agents. The overcoat material should not be removed, scraped, touched, pressed, or pulled to avoid stress damage and possible breakage of delicate wire bonds. Surface dust can be carefully removed with a soft brush, or canned air such as those used for cleaning photographic lenses. The silicone overcoat material has a flammability classification of 94 V-1 and a temperature rating of 130 C. Mechanical Stress This component is not suitable for SMT / solder reflow operations. Refrain from twisting leads or unconstrained crimp or lead cut forces, which could break the glass seals of the leads and break internal wire bonds. Life Support OPTO TECHNOLOGY PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF OPTO TECHNOLOGY INC. As used herein: a. Life support devices or systems are devices or systems which (1) are intended for surgical implant into the body, or (2) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. b. A critical component is any component of a life support device or system whose failure to perform can be reasonably be expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. The information provided herein is believed to be reliable, however OPTO TECHNOLOGY INC. assumes no responsibility for inaccuracies or omissions. OPTO TECHNOLOGY INC. reserves the right to make changes at any time without notice to any products to improve reliability, function or design or to circuitry or specifications. OPTO TECHNOLOGY INC. does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights, nor the rights of others. OPTO TECHNOLOGY, INC. 562 Chaddick Drive, Wheeling, IL 60090 Phone: (847) 537-4277 FAX: (847) 537-4785 Website: www.optotech.com DATA SHEET REV. B (9/14/01) Page 4 of 4