ADVANCED LINEAR DEVICES, INC. TM e ALD110814/ALD110914 VGS(th)= +1.4V GENERAL DESCRIPTION APPLICATIONS ALD110814/ALD110914 are monolithic quad/dual N-Channel MOSFETs matched at the factory using ALD's proven EPAD(R) CMOS technology. These devices are intended for low voltage, small signal applications. * Precision current mirrors * Precision current sources * Voltage choppers * Differential amplifier input stages * Discrete voltage comparators * Voltage bias circuits * Sample and Hold circuits * Analog inverters * Level shifters * Source followers and buffers * Current multipliers * Discrete analog multiplexers/matrices * Discrete analog switches The ALD110814/ALD110914 MOSFETs are designed and built with exceptional device electrical characteristics matching. Since these devices are on the same monolithic chip, they also exhibit excellent tempco tracking characteristics. Each device is versatile as a circuit element and is a useful design component for a broad range of analog applications. They are basic building blocks for current sources, differential amplifier input stages, transmission gates, and multiplexer applications. For most applications, connect V- and N/C pins to the most negative voltage potential in the system and V+ pin to the most positive voltage potential (or left open unused). All other pins must have voltages within these voltage limits. The ALD110814/ALD110914 devices are built for minimum offset voltage and differential thermal response, and they are designed for switching and amplifying applications in +1.5V to +10V systems where low input bias current, low input capacitance and fast switching speed are desired. Since these are MOSFET devices, they feature very large (almost infinite) current gain in a low frequency, or near DC, operating environment. PIN CONFIGURATION ALD110814 N/C* The ALD110814/ALD110914 are suitable for use in precision applications which require very high current gain, beta, such as current mirrors and current sources. The high input impedance and the high DC current gain of the Field Effect Transistors result in extremely low current loss through the control gate. The DC current gain is limited by the gate input leakage current, which is specified at 30pA at room temperature. For example, DC beta of the device at a drain current of 3mA and input leakage current of 30pA at 25C is = 3mA/30pA = 100,000,000. FEATURES * Enhancement-mode (normally off) * Standard Gate Threshold Voltages: +1.4V * Matched MOSFET to MOSFET characteristics * Tight lot to lot parametric control * Parallel connection of MOSFETs to increase drain currents * Low input capacitance * VGS(th) match to 10mV * High input impedance -- 1012 typical * Positive, zero, and negative VGS(th) temperature coefficient * DC current gain >108 * Low input and output leakage currents ORDERING INFORMATION Operating Temperature Range* 0C to +70C 0C to +70C ALD110814PCL 16-Pin SOIC Package ALD110814SCL D LE AB EN QUAD/DUAL N-CHANNEL ENHANCEMENT MODE EPAD(R) MATCHED PAIR MOSFET ARRAY 16-Pin Plastic Dip Package (R) EPAD 8-Pin Plastic Dip Package ALD110914PAL 8Pin SOIC Package 1 GN1 2 DN1 3 S12 4 V- 5 DN4 6 GN4 7 N/C* 8 V- V- M1 M2 V+ VM4 M3 16 N/C* 15 GN2 14 DN2 13 V+ 12 S34 11 DN3 10 9 V- V- GN3 N/C* PCL, SCL PACKAGES ALD110914 N/C* 1 GN1 2 DN1 3 S12 4 V- V- M1 M2 V- 8 N/C* 7 GN2 6 DN2 5 V- PAL, SAL PACKAGES *N/C pins are internally connected. Connect to V- to reduce noise ALD110914SAL * Contact factory for industrial or military temp. ranges or user-specified threshold voltage values. (c)2008 Advanced Linear Devices, Inc. 415 Tasman Drive, Sunnyvale, California 94089-1706 Tel: (408) 747-1155 Fax: (408) 747-1286 www.aldinc.com ABSOLUTE MAXIMUM RATINGS Drain-Source voltage, VDS Gate-Source voltage, VGS Power dissipation Operating temperature range PA, SA, PC, SC package Storage temperature range Lead temperature, 10 seconds 10.6V 10.6V 500 mW 0C to +70C -65C to +150C +260C OPERATING ELECTRICAL CHARACTERISTICS V+ = +5V (or open) V- = GND TA = 25C unless otherwise specified CAUTION: ESD Sensitive Device. Use static control procedures in ESD controlled environment. ALD110814 / ALD110914 Parameter Symbol Min 1.38 Typ Max Unit Test Conditions 1.40 1.42 V IDS =1A VDS = 0.1V 10 mV IDS =1A Gate Threshold Voltage VGS(th) Offset Voltage VGS(th)1-VGS(th)2 VOS 3 Offset VoltageTempco TC VOS 5 V/ C VDS1 = VDS2 GateThreshold Voltage Tempco TCVGS(th) -1.7 0.0 +1.6 mV C ID = 1A ID = 20A, VDS = 0.1V ID = 40A On Drain Current IDS (ON) 12.0 3.0 mA VGS = +10.6V VGS = + 5.4V VDS = + 5V Forward Transconductance GFS 1.4 mmho VGS = +5.4V VDS = +10.4V Transconductance Mismatch GFS 1.8 % Output Conductance GOS 68 mho Drain Source On Resistance RDS (ON) 500 Drain Source On Resistance Mismatch RDS (ON) 0.5 % Drain Source Breakdown Voltage BVDSX Drain Source Leakage Current1 IDS (OFF) Gate Leakage Current1 10 VGS = + 5.4V VDS = +10.4V VDS = 0.1V VGS = +5.6V V IDS = 1.0A VGS = +0.4V 10 100 4 pA nA VGS = +0.4V VDS =10V, TA = 125C IGSS 3 30 1 pA nA VDS = 0V VGS = 10V TA =125C Input Capacitance CISS 2.5 pF Transfer Reverse Capacitance CRSS 0.1 pF Turn-on Delay Time ton 10 ns V+ = 5V RL= 5K Turn-off Delay Time toff 10 ns V+ = 5V RL= 5K 60 dB f = 100KHz Crosstalk Notes: 1 Consists of junction leakage currents ALD110814/ALD110914 Advanced Linear Devices 2