DATA SHEET
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
The information in this document is subject to change without notice. Before using this document, please confirm that
this is the latest version.
L-BAND HIGH POWER SPDT SWITCH
GaAs INTEGRATED CIRCUIT
μ
PG2009TB
Document No. PG10191EJ02V0DS (2nd edition)
Date Published July 2004 CP(K)
DESCRIPTION
The
μ
PG2009TB is an L-band SPDT (Single Pole Double Throw) GaAs FET switch which was developed for digital
cellular or cordless telephone application. The device can operate from 500 MHz to 2.5 GHz, having the low insertion
loss and high isolation by 2.8 V control voltage.
FEATURES
•Low insertion loss : LINS = 0.25 dB TYP. @ Vcont1/2 = 2.8 V/0 V, f = 1.0 GHz
LINS = 0.30 dB TYP. @ Vcont1/2 = 2.8 V/0 V, f = 2.0 GHz
•High isolation : ISL = 28 dB TYP. @ Vcont1/2 = 2.8 V/0 V, f = 2.0 GHz
•High power : Pin (0.1dB) = 34 dBm TYP. @ Vcont1/2 = 2.8 V/0 V, f = 1.0 GHz
•6-pin super minimold package (2.0 × 1.25 × 0.9 mm)
APPLICATION
•L-band digital cellular or cordless telephone
•BuletoothTM, W-LAN and WLL applications
ORDERING INFORMATION
mroF gniylppuS gnikraM egakcaP rebmuN traP
μ
PG2009TB-E3 6-pin super minimold G2U •Embossed tape 8 mm wide
•Pin 1, 2, 3 face the perforation side of the tape
•Qty 3 kpcs/reel
Remark To order evaluation samples, contact your nearby sales office.
Part number for sample order:
μ
PG2009TB-A
The mark shows major revised points.
PHASE-OUT
Drop-In Replacement:
CG2409M2 with Pin Mapping
Data Sheet PG10191EJ02V0DS
2
μ
PG2009TB
PIN CONNECTIONS
Pin No. Pin Name
1 OUT1
2 GND
3 OUT2
4 Vcont2
5 IN
1
2
3
6
5
4
(Top View)
G2U
6
5
4
1
2
3
(Bottom View)
6 Vcont1
ABSOLUTE MAXIMUM RATINGS (TA = +25°C, unless otherwise specified)
Parameter Symbol Ratings Unit
Control Voltage 1, 2 Vcont1, 2 −6.0 to +6.0 Note V
P rewoP tupnI in +36 dBm
Total Power Dissipation Ptot 0.15 W
Operating Ambient Temperature TA −45 to +85 °C
Storage Temperature Tstg −55 to +150 °C
Note ⏐Vcont1-Vcont2⏐ ≤ 6.0 V
RECOMMENDED OPERATING RENGE (TA = +25°C)
Parameter Symbol MIN. TYP. MAX. Unit
Control Voltage (High) Vcont(H) +2.7 +2.8 +3.0 V
Control Voltage (Low) Vcont(L) −0.2 0 +0.2 V
PHASE-OUT
D
rop-In Replacement:
CG2409M2 with Pin Mapping
Data Sheet PG10191EJ02V0DS 3
μ
PG2009TB
ELECTRICAL CHARACTERISTICS
(TA = +25°C, Vcont1 = 2.8 V, Vcont2 = 0 V or Vcont1 = 0 V, Vcont2 = 2.8 V, ZO = 50 Ω, Off chip DC blocking
capacitors value; 56 pF, unless otherwise specified)
Parameter Symbol Test Conditions MIN. TYP. MAX. Unit
L ssoL noitresnI INS f = 0.5 to 1.0 GHz −0.25 0.45 dB
zHG 0.2 = f −0.30 0.50 dB
zHG 5.2 = f −0.40 −dB
82 42 zHG 0.2 ot 5.0 = f LSI noitalosI −dB
zHG 5.2 = f −25 −dB
LR ssoL nruteR tupnI in 02 51 zHG 5.2 ot 5.0 = f −dB
Output Return Loss RLout 02 51 zHG 5.2 ot 5.0 = f −dB
Input Power at 0.1 dB
Compression Point Note
Pin(0.1 dB) f = 1.0 GHz,
Vcont = 2.8 V/0 V
32.5 34 −dBm
V ,zHG 0.1 = f 0f2 scinomraH dn2 cont = 2.8 V/0 V,
Pin = 30.5 dBm
65 75 −dBc
V ,zHG 0.1 = f 0f3 scinomraH dr3 cont = 2.8 V/0 V,
Pin = 30.5 dBm
65 75 −dBc
t deepS gnihctiwS SW −150 −ns
I tnerruC lortnoC cont Vcont = 2.8 V/0 V, RF Non −1 50
μ
A
Note Pin(0.1 dB) are measured the input power level when the insertion loss increase more 0.1 than that of linear
range. All other characteristics are measured in linear range.
Caution When the
μ
PG2009TB is used it is necessary to use DC blocking capacitors for No.1 (OUT1), No.3
(OUT2) and No.5 (IN). The value of DC blocking capacitors should be chosen to accommodate the
frequency of operation, bandwidth, switching speed and the condition with actual board of your
system.
The range of recommended DC blocking capacitor value is less than 100 pF.
PHASE-OUT
Drop-In Replacement:
CG2409M2 with Pin Mapping
Data Sheet PG10191EJ02V0DS
4
μ
PG2009TB
EVALUATION CIRCUIT
Vcont1 = 2.8 V, Vcont2 = 0 V or Vcont2 = 0 V, Vcont1 = 2.8 V, off chip DC blocking capacitors value C1 = 56 pF, C2
= 1 000 pF (Bypass), using the standard evaluation board.
1
2
3
6
5
4
Vcont2
IN
Vcont1
C2
C2
C1
C1
C1
OUT2
OUT1
G2U
EVALUATION BOARD
6pin SMM SPDT SW
V
cont2
C2
C2
G2U
C1
C1
C1
OUT2
OUT1
V
cont1
IN
TRUTH TABLE
Vcont1 Vcont2 IN−OUT1 IN−OUT2
Low High OFF ON
High Low ON OFF
PHASE-OUT
Data Sheet PG10191EJ02V0DS 5
μ
PG2009TB
TYPICAL CHARACTERISTICS (TA = +25°C, Vcont1/2 = 2.8 V/0 V, Pin = 0 dBm, OUT2 side is 50 Ω
termination, unless otherwise specified)
Input Return Loss RL
in
(dB)
Frequency f
(GHz)
0
–20
–40
INPUT RETURN LOSS vs. FREQUENCY
START 0.500 000 000 GHz STOP 3.000 000 000 GHz
S
11
log MAG Bd 0 FER /Bd 011HC
2: –30.339 dB
1.5 GHz
1: –25.43 dB
1.0 GHz
3: –30.025 dB
2.0 GHz
4: –23.812 dB
2.5 GHz
5: –17.85 dB
3.0 GHz
Insertion Loss L
INS
(dB)
Frequency f
(GHz)
0
–2.0
–4.0
INSERTION LOSS vs. FREQUENCY
START 0.500 000 000 GHz STOP 3.000 000 000 GHz
S
21
log MAG Bd 0 FER /Bd 11HC
2: –0.744 dB
1.5 GHz
1: –0.620 dB
1.0 GHz
3: –0.881 dB
2.0 GHz
4: –1.057 dB
2.5 GHz
5: –1.302 dB
3.0 GHz
Isolation ISL (dB)
Frequency f
(GHz)
0
–20
–40
ISOLATION vs. FEQUENCY
START 0.500 000 000 GHz STOP 3.000 000 000 GHz
S
21
log MAG Bd 0 FER /Bd 011HC
2: –28.871 dB
1.5 GHz
1: –28.787 dB
1.0 GHz
3: –27.75 dB
2.0 GHz
4: –24.902 dB
2.5 GHz
5: –21.582 dB
3.0 GHz
Output Return Loss RL
out
(dB)
Frequency f
(GHz)
0
–20
–40
OUTPUT RETERN LOSS vs. FREQUENCY
START 0.500 000 000 GHz STOP 3.000 000 000 GHz
S
22
log MAG Bd 0 FER /Bd 011HC
2: –31.882 dB
1.5 GHz
1: –25.992 dB
1.0 GHz
3: –32.46 dB
2.0 GHz
4: –25.087 dB
2.5 GHz
5: –18.145 dB
3.0 GHz
11
1
3
3
1
23
4
5
2345
245
2
4
5
Caution These characteristics values include the losses of the evaluation board.
Remark The graphs indicate nominal characteristics.
PHASE-OUT
Data Sheet PG10191EJ02V0DS
6
μ
PG2009TB
TYPICAL CHARACTERISTICS
(f = 2 GHz, OUT2 side is 50 Ω termination, unless otherwise specified)
Input Power P
in
(dBm)
Insersion Loss L
INS
(dB)
0.5
0.6
25 27 29 31 33 35 37
0.4
0.3
0.2
0.1
0
RELATION BETWEEN CONTROL
VOLTAGE OF INSERSION LOSS
V
cont
= 2.4 V
V
cont
= 2.8 V
V
cont
= 3.2 V
26 28 30 32 34 36
0.7
0.8
0.9
Input Power P
in
(dBm)
2nd Harmonics 2f0 (dBc)
50
60
25 27 29 31 33 35 37
40
30
20
10
0
RELATION BETWEEN CONTROL
VOLTAGE OF 2nd HARMONICS
V
cont
= 2.4 V
V
cont
= 2.8 V
V
cont
= 3.2 V
26 28 30 32 34 36
70
80
90
Input Power P
in
(dBm)
3rd Harmonics 3f0 (dBc)
50
60
25 27 29 31 33 35 37
40
30
20
10
0V
cont
= 2.4 V
V
cont
= 2.8 V
V
cont
= 3.2 V
26 28 30 32 34 36
70
80
90
RELATION BETWEEN CONTROL
VOLTAGE OF 3rd HARMONICS
Remark The graphs indicate nominal characteristics.
PHASE-OUT
Data Sheet PG10191EJ02V0DS 7
μ
PG2009TB
PACKAGE DIMENSIONS
6-PIN SUPER MINIMOLD (UNIT: mm)
0.9±0.1
0.7
0 to 0.1
0.15
+0.1
–0.05
0.2
+0.1
–0.05
2.0±0.2
1.3
0.650.65
1.25±0.1
2.1±0.1
0.1 MIN.
PHASE-OUT
Data Sheet PG10191EJ02V0DS
8
μ
PG2009TB
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
gniredloS dohteM gniredloS lobmyS noitidnoC snoitidnoC
Infrared Reflow Peak temperature (package surface temperature) : 260°C or below
ssel ro sdnoces 01 : erutarepmet kaep ta emiT
Time at temperature of 220°C or higher : 60 seconds or less
Preheating time at 120 to 180°021 : C ±30 seconds
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
IR260
512 : )erutarepmet ecafrus egakcap( erutarepmet kaeP SPV °C or below
Time at temperature of 200°C or higher : 25 to 40 seconds
Preheating time at 120 to 150° sdnoces 06 ot 03 : C
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
VP215
Wave Soldering Peak temperature (molten solder temperature) : 260°C or below
ssel ro sdnoces 01 : erutarepmet kaep ta emiT
Preheating temperature (package surface temperature) : 120°C or below
Maximum number of flow processes : 1 time
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
WS260
Partial Heating Peak temperature (pin temperature) : 350°C or below
Soldering time (per side of device) : 3 seconds or less
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
HS350
Caution Do not use different soldering methods together (except for partial heating).
PHASE-OUT
μ
PG2009TB
SAFETY INFORMATION ON THIS PRODUCT
Caution GaAs Products The product contains gallium arsenide, GaAs.
GaAs vapor and powder are hazardous to human health if inhaled or ingested.
•Do not destroy or burn the product.
•Do not cut or cleave off any part of the product.
•Do not crush or chemically dissolve the product.
•Do not put the product in the mouth.
Follow related laws and ordinances for disposal. The product should be excluded from general
industrial waste or household garbage.
PHASE-OUT
NOTICE
1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and
application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. California
Eastern Laboratories and Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits,
software, or information.
2. California Eastern Laboratories has used reasonable care in preparing the information included in this document, but California Eastern Laboratories does
not warrant that such information is error free. California Eastern Laboratories and Renesas Electronics assumes no liability whatsoever for any damages
incurred by you resulting from errors in or omissions from the information included herein.
3. California Eastern Laboratories and Renesas Electronics do not assume any liability for infringement of patents, copyrights, or other intellectual property
rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express,
implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of California Eastern Laboratories or Renesas
Electronics or others.
4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. California Eastern
Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties arising from such alteration, modication, copy
or otherwise misappropriation of Renesas Electronics product.
5. Renesas Electronics products are classied according to the following two quality grades: “Standard” and “High Quality”. The recommended applications
for each Renesas Electronics product depends on the product’s quality grade, as indicated below. “Standard”: Computers; ofce equipment; communications
equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and
industrial robots etc. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); trafc control systems; anti-disaster systems; anti-crime
systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct
threat to human life or bodily injury (articial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear
reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular
application. You may not use any Renesas Electronics product for any application for which it is not intended. California Eastern Laboratories and Renesas
Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product
for which the product is not intended by California Eastern Laboratories or Renesas Electronics.
6. You should use the Renesas Electronics products described in this document within the range specied by California Eastern Laboratories, especially with
respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product
characteristics. California Eastern Laboratories shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products
beyond such specied ranges.
7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specic characteristics such as
the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation
resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by
re in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy,
re control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of
microcomputer software alone is very difcult, please evaluate the safety of the nal products or systems manufactured by you.
8. Please contact a California Eastern Laboratories sales ofce for details as to environmental matters such as the environmental compatibility of each Renesas
Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive. California Eastern Laboratories and Renesas Electronics assume no liability for
damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited
under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document
for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When
exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations.
10. It is the responsibility of the buyer or distributor of California Eastern Laboratories, who distributes, disposes of, or otherwise places the Renesas Electronics
product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, California Eastern Laboratories and
Renesas Electronics assume no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products.
11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of California Eastern Laboratories.
12. Please contact a California Eastern Laboratories sales ofce if you have any questions regarding the information contained in this document or Renesas
Electronics products, or if you have any other inquiries.
NOTE 1: “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
NOTE 2: “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
NOTE 3: Products and product information are subject to change without notice.
CEL Headquarters • 4590 Patrick Henry Drive, Santa Clara, CA 95054 • Phone (408) 919-2500 • www.cel.com
For a complete list of sales ofces, representatives and distributors,
Please visit our website: www.cel.com/contactus
PHASE-OUT
