[ /Title (CD74 HC299 , CD74 HCT29 9) /Subject (High Speed CMOS Logic 8-Bit Universal Shift CD54HC299, CD74HC299, CD54HCT299, CD74HCT299 Data sheet acquired from Harris Semiconductor SCHS178C January 1998 - Revised May 2003 High-Speed CMOS Logic 8-Bit Universal Shift Register; Three-State Features Description The 'HC259 and 'HCT299 are 8-bit shift/storage registers with three-state bus interface capability. The register has four synchronous-operating modes controlled by the two select inputs as shown in the mode select (S0, S1) table. The mode select, the serial data (DS0, DS7) and the parallel data (I/O0 - I/O7) respond only to the low-to-high transition of the clock (CP) pulse. S0, S1 and data inputs must be stable one setup time prior to the clock positive transition. * Buffered Inputs * Four Operating Modes: Shift Left, Shift Right, Load and Store * Can be Cascaded for N-Bit Word Lengths * I/O0 - I/O7 Bus Drive Capability and Three-State for Bus Oriented Applications * Typical fMAX = 50MHz at VCC = 5V, CL = 15pF, TA = 25oC The Master Reset (MR) is an asynchronous active low input. When MR output is low, the register is cleared regardless of the status of all other inputs. The register can be expanded by cascading same units by tying the serial output (Q0) to the serial data (DS7) input of the preceding register, and tying the serial output (Q7) to the serial data (DS0) input of the following register. Recirculating the (n x 8) bits is accomplished by tying the Q7 of the last stage to the DS0 of the first stage. * Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads * Wide Operating Temperature Range . . . -55oC to 125oC * Balanced Propagation Delay and Transition Times * Significant Power Reduction Compared to LSTTL Logic ICs The three-state input/output I(/O) port has three modes of operation: * HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30% of VCC at VCC = 5V 1. Both output enable (OE1 and OE2) inputs are low and S0 or S1 or both are low, the data in the register is presented at the eight outputs. 2. When both S0 and S1 are high, I/O terminals are in the high impedance state but being input ports, ready for parallel data to be loaded into eight registers with one clock transition regardless of the status of OE1 and OE2. * HCT Types - 4.5V to 5.5V Operation - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il 1A at VOL, VOH 3. Either one of the two output enable inputs being high will force I/O terminals to be in the off-state. It is noted that each I/O terminal is a three-state output and a CMOS buffer input. Pinout Ordering Information CD54HC299, CD54HCT299 (CERDIP) CD74HC299, CD74HCT299 (PDIP, SOIC) TOP VIEW TEMP. RANGE (oC) PACKAGE CD54HC299F3A -55 to 125 20 Ld CERDIP CD54HCT299F3A -55 to 125 20 Ld CERDIP CD74HC299E -55 to 125 20 Ld PDIP CD74HC299M -55 to 125 20 Ld SOIC PART NUMBER S0 1 20 VCC OE1 2 19 S1 OE2 3 18 DS7 I/O6 4 17 Q7 CD74HC299M96 -55 to 125 20 Ld SOIC I/O4 5 16 I/O7 CD74HCT299E -55 to 125 20 Ld PDIP I/O2 6 15 I/O5 CD74HCT299M -55 to 125 20 Ld SOIC I/O0 7 14 I/O3 Q0 8 13 I/O1 CD74HCT299M96 -55 to 125 20 Ld SOIC MR 9 12 CP GND 10 NOTE: When ordering, use the entire part number. The suffix 96 denotes tape and reel. 11 DS0 CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright (c) 2003, Texas Instruments Incorporated 1 CD54HC299, CD74HC299, CD54HCT299, CD74HCT299 Functional Diagram CP OE1 OE2 12 2 3 MR 9 20 THREESTATE CONTROL VCC 7 I/O 0 I/O 2 BUS LINE OUTPUTS I/O THREE-STATE OUTPUTS 6 5 SHIFT REGISTER I/O THREE-STATE OUTPUTS I/O 4 4 I/O 6 8 STANDARD OUTPUT Q0 1 S0 MODE SELECTION 10 GND 13 I/O 1 14 I/O 3 BUS LINE 15 I/O 5 OUTPUTS 16 I/O7 17 STANDARD Q7 OUTPUT 19 S1 11 18 DS0 DS7 MODE SELECT FUNCTION TABLE THREE-STATE I/O PORT OPERATING MODE INPUTS FUNCTION INPUTS/OUTPUTS OE1 OE2 S0 S1 Qn (REGISTER) I/O0 --- I/O7 L L L X L L L L L X H H L L X L L L L L X L H H Load Register X X H H Qn = I/On I/On = Inputs Disable I/O H X X X X (Z) X H X X X (Z) Read Register TRUTH TABLE INPUTS REGISTER OUTPUTS FUNCTION MR CP S0 S1 DS0 DS7 I/On Q0 Q1 --- Q6 Q7 RESET (CLEAR) L X X X X X X L L --- L L H h l l X X L q0 --- q5 q6 H h l h X X H q0 --- q5 Q6 H l h X l X q1 q2 --- q7 L H l h X h X q1 q2 --- q7 H Hold (Do Nothing) H l l X X X q0 q1 --- q6 q7 Parallel Load H h h X X l L L --- L L H h h X X h H H --- H H Shift Right Shift Left H = Input Voltage High Level, h = Input voltage high one set-up timer prior clock transition; L = Input Voltage Low Level; l = Input voltage low one set-up time prior to clock transition; qn = Lower case letter indicates the state of the reference output one set-up time prior to clock transition; X - Voltage level on logic status don't care; Z = Output in high impedance state, = Low to High Clock Transition. 2 CD54HC299, CD74HC299, CD54HCT299, CD74HCT299 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .20mA DC Drain Current, per Output, IO, For -0.5V < VO < VCC + 0.5V For Q Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25mA For I/O Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .25mA DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .50mA Thermal Resistance (Typical, Note 1) JA (oC/W) E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. The package thermal impedance is calculated in accordance with JESD 51-7. DC Electrical Specifications TEST CONDITIONS SYMBOL VI (V) IO (mA) High Level Input Voltage VIH - - Low Level Input Voltage VIL High Level Output Voltage CMOS Loads VOH PARAMETER VCC (V) 25oC -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS HC TYPES - - VIH or VIL High Level Output Voltage TTL Loads -0.02 VOL Input Leakage Current VCC or GND - 1.5 - 1.5 - V - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V 2 1.9 - - 1.9 - 1.9 - V 4.5 4.4 - - 4.4 - 4.4 - V 6 5.9 - - 5.9 - 5.9 - V I/On - - - - - - - - V -6 4.5 3.98 - - 3.84 - 3.7 - V -7.8 0.02 6 5.48 - - 5.34 - 5.2 - V 2 - - 0.1 - 0.1 - 0.1 V 4.5 - - 0.1 - 0.1 - 0.1 V 6 - - 0.1 - 0.1 - 0.1 V I/On - - - - - - - - V 4 6 4.5 - - 0.26 - 0.33 - 0.4 V 5.2 7.8 6 - - 0.26 - 0.33 - 0.4 V 6 - - 0.1 - 1 - 1 A Qn II - -4 VIH or VIL Low Level Output Voltage TTL Loads 1.5 3.15 Qn -5.2 Low Level Output Voltage CMOS Loads 2 4.5 - 3 CD54HC299, CD74HC299, CD54HCT299, CD74HCT299 DC Electrical Specifications (Continued) TEST CONDITIONS 25oC -40oC TO 85oC -55oC TO 125oC PARAMETER SYMBOL VI (V) IO (mA) VCC (V) Quiescent Device Current ICC VCC or GND 0 6 - - 8 - 80 - 160 A - 6 - - 0.5 - 5 - 10 A Three- State Leak- VIL or VIH VO = VCC or GND age Current MIN TYP MAX MIN MAX MIN MAX UNITS HCT TYPES High Level Input Voltage VIH - - 4.5 to 5.5 2 - - 2 - 2 - V Low Level Input Voltage VIL - - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V High Level Output Voltage CMOS Loads VOH VIH or VIL -0.02 4.5 4.4 - - 4.4 - 4.4 - V -4 4.5 3.98 - - 3.84 - 3.7 - V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 4 4.5 - - 0.26 - 0.33 - 0.4 V 0.1 - 1 - 1 A High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current II VCC and GND 0 5.5 - ICC VCC or GND 0 5.5 - - 8 - 80 - 160 A - 6 - - 0.5 - 5 - 10 A - 4.5 to 5.5 - 100 360 - 450 - 490 A Three- State Leak- VIL or VIH VO = VCC age Current or GND Additional Quiescent Device Current Per Input Pin: 1 Unit Load ICC (Note 2) VCC -2.1 NOTE: 2. For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table INPUT UNIT LOADS S1, MR 0.25 I/O0 - I/O7 0.25 DS0, DS7 0.25 S0, CP 0.6 OE1, OE2 0.3 NOTE: Unit Load is ICC limit specific in Static Specifications Table, e.g., 360A max. at 25oC. 4 CD54HC299, CD74HC299, CD54HCT299, CD74HCT299 Prerequisite for Switching Specifications 25oC PARAMETER -40oC TO 85oC -55oC TO 125oC SYMBOL VCC (V) MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS fMAX 2 6 - - 5 - - 4 - - MHz 4.5 30 - - 25 - - 20 - - MHz 6 35 - - 29 - - 23 - - MHz 2 50 - - 65 - - 75 - - ns 4.5 10 - - 13 - - 15 - - ns 6 9 - - 11 - - 13 - - ns 2 80 - - 100 - - 120 - - ns 4.5 16 - - 20 - - 24 - - ns 6 14 - - 17 - - 20 - - ns 2 100 - - 125 - - 150 - - ns 4.5 20 - - 25 - - 30 - - ns 6 17 - - 21 - - 26 - - ns 2 0 - - 0 - - 0 - - ns 4.5 0 - - 0 - - 0 - - ns 6 0 - - 0 - - 0 - - ns 2 5 - - 5 - - 5 - - ns 4.5 5 - - 5 - - 5 - - ns 6 5 - - 5 - - 5 - - ns 2 120 - - 150 - - 180 - - ns 4.5 24 - - 30 - - 36 - - ns 6 20 - - 26 - - 31 - - ns HC TYPES Maximum Clock Frequency MR Pulse Width Clock Pulse Width Setup Time DS0, DS7, I/On to Clock Hold Time DS0, DS7, I/On, S0, S1 to Clock Recovery Time MR to Clock Setup Time S1, S0 to Clock tW tW tSU tH tREC tSU HCT TYPES Maximum Clock Frequency fMAX 4.5 25 - - 20 - - 16 - - MHz MR Pulse Width tW 4.5 15 - - 19 - - 22 - - ns Clock Pulse Width tW 4.5 20 - - 25 - - 30 - - ns Setup Time DS0, DS7, I/On, S0, S1 to Clock tSU 4.5 20 - - 25 - - 30 - - ns Hold Time DS0, DS7, I/On, S0, S1 to Clock tH 4.5 0 - - 0 - - 0 - - ns Recovery Time MR to Clock tREC 4.5 5 - - 5 - - 5 - - ns Setup Time S1, S0 to Clock tSU 4.5 27 - - 34 - - 41 - - ns 5 CD54HC299, CD74HC299, CD54HCT299, CD74HCT299 Switching Specifications CL = 50pF, Input tr, tf = 6ns -40oC TO 85oC 25oC PARAMETER SYMBOL TEST CONDITIONS tPLH, tPHL CL = 50pF -55oC TO 125oC VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS 2 - - 200 - 250 - 300 ns 4.5 - - 40 - 50 - 60 ns CL = 15pF 5 - 17 - - - - - ns CL = 50pF 6 - - 34 - 43 - 51 ns CL = 15pF 5 - 10 - - - - - ns tPZH, tPLZ - 13 - - - - - ns tPHZ - 15 - - - - - ns 2 - - 155 - 195 - 235 ns 4.5 - - 31 - 39 - 47 ns 6 - - 26 - 33 - 40 ns 2 - - 185 - 230 - 280 ns 4.5 - - 37 - 46 - 56 ns 6 - - 31 - 39 - 48 ns 2 - - 155 - 195 - 235 ns 4.5 - - 31 - 39 - 47 ns 6 - - 26 - 33 - 40 ns 2 - - 130 - 165 - 195 ns 4.5 - - 26 - 33 - 39 ns 6 - - 22 - 28 - 33 ns 2 - - 75 - 95 - 110 ns 4.5 - - 15 - 19 - 22 ns 6 - - 13 - 16 - 19 ns 2 - - 60 - 75 - 90 ns 4.5 - - 12 - 15 - 18 ns 6 - - 10 - 13 - 15 ns HC TYPES Propagation Delay Clock to I/O Output, Clock to Q0 and Q7, MR to Output Output Enable and Disable Times Output High-Z to High Level Output High Level to High-Z Output Low Level to High-Z Output High-Z to Low Level Output Transition Time tPZL tPZH tPHZ tPLZ tPZL tTHL, tTLH CL = 50pF CL = 50pF CL = 50pF CL = 50pF CL = 50pF Q0, Q7 I/O0 to I/O7 tTHL, tTLH CL = 50pF Input Capacitance CI CL = 50pF - 10 - 10 - 10 - 10 pF Three-State Output Capacitance CO - - 20 - 20 - 20 - 20 pF Power Dissipation Capacitance (Notes 3, 4) CPD CL = 15pF 5 - 150 - - - - - pF 6 CD54HC299, CD74HC299, CD54HCT299, CD74HCT299 Switching Specifications CL = 50pF, Input tr, tf = 6ns (Continued) -40oC TO 85oC 25oC PARAMETER SYMBOL -55oC TO 125oC TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS CL = 50pF 4.5 - - 45 - 56 - 68 ns CL = 15pF 5 - 19 - - - - - ns HCT TYPES Propagation Delay tPHL, tPLH Clock to I/O Output, Clock to Q0 and Q7 MR to Output tPHL, tPLH CL = 50pF 4.5 - - 46 - 58 - 69 ns Output Enable and Disable Times tPZL,tPZH, tPLZ, tPHZ CL = 15pF 5 - 10, 13, 15 - - - - - ns Output High-Z to High Level tPZH CL = 50pF 4.5 - - 32 - 40 - 48 ns Output High Level to High-Z tPHZ CL = 50pF 4.5 - - 37 - 46 - 56 ns Output Low Level to High-Z tPLZ CL = 50pF 4.5 - - 32 - 40 - 48 ns Output High-Z to Low Level tPZL CL = 50pF 4.5 - - 30 - 38 - 45 ns Q0, Q7 CL = 50pF 4.5 - - 15 - 19 - 22 ns I/O0 to I/O7 CL = 50pF 4.5 - - 12 - 15 - 18 ns Output Transition Time tTLH, tTHL Input Capacitance CIN CL = 50pF - 10 - 10 - 10 - 10 pF Three-State Output Capacitance CO - - 20 - 20 - 20 - 20 pF Power Dissipation Capacitance (Notes 3, 4) CPD CL = 15pF 5 - 170 - - - - - pF NOTES: 3. CPD is used to determine the dynamic power consumption, per register. 4. PD = CPD VCC2 fi + (CL VCC2 fO) where fi = Input Frequency, fO = Output Frequency, CL = Output Load Capacitance, VCC = Supply Voltage. Test Circuits and Waveforms tfCL trCL CLOCK 90% 10% tWL + tWH = I fCL tWL 50% tfCL = 6ns I fCL 3V VCC 50% 10% tWL + tWH = trCL = 6ns CLOCK 50% 2.7V 0.3V GND 1.3V 0.3V tWL tWH NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. 1.3V 1.3V GND tWH NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. FIGURE 1. HC CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH FIGURE 2. HCT CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH 7 CD54HC299, CD74HC299, CD54HCT299, CD74HCT299 Test Circuits and Waveforms tr = 6ns (Continued) tf = 6ns 90% 50% 10% INPUT GND tTLH 90% INVERTING OUTPUT tPHL FIGURE 3. HC TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC trCL VCC 90% GND tH(H) 3V 2.7V 1.3V 0.3V GND tH(H) tH(L) VCC DATA INPUT DATA INPUT 50% tH(L) 3V 1.3V 1.3V 1.3V GND tSU(H) tSU(H) tSU(L) tTLH 90% OUTPUT tTHL 90% 50% 10% tTLH 90% 1.3V OUTPUT tREM 3V SET, RESET OR PRESET GND tTHL 1.3V 10% FIGURE 5. HC SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS tPHL 1.3V GND IC CL 50pF GND 90% tPLH 50% IC tSU(L) tPHL tPLH tREM VCC SET, RESET OR PRESET tfCL CLOCK INPUT 50% 10% tPLH FIGURE 4. HCT TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC tfCL trCL tTLH 1.3V 10% tPLH tPHL GND tTHL 90% 50% 10% INVERTING OUTPUT 3V 2.7V 1.3V 0.3V INPUT tTHL CLOCK INPUT tf = 6ns tr = 6ns VCC CL 50pF FIGURE 6. HCT SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS 8 CD54HC299, CD74HC299, CD54HCT299, CD74HCT299 Test Circuits and Waveforms 6ns (Continued) 6ns OUTPUT DISABLE tr VCC 90% 50% 10% OUTPUTS ENABLED OUTPUT HIGH TO OFF 50% OUTPUTS DISABLED FIGURE 7. HC THREE-STATE PROPAGATION DELAY WAVEFORM OTHER INPUTS TIED HIGH OR LOW OUTPUT DISABLE IC WITH THREESTATE OUTPUT GND 1.3V tPZH 90% OUTPUTS ENABLED OUTPUTS ENABLED 0.3 10% tPHZ tPZH 90% 3V tPZL tPLZ OUTPUT LOW TO OFF 50% OUTPUT HIGH TO OFF 6ns GND 10% tPHZ tf 2.7 1.3 tPZL tPLZ OUTPUT LOW TO OFF 6ns OUTPUT DISABLE 1.3V OUTPUTS DISABLED OUTPUTS ENABLED FIGURE 8. HCT THREE-STATE PROPAGATION DELAY WAVEFORM OUTPUT RL = 1k CL 50pF VCC FOR tPLZ AND tPZL GND FOR tPHZ AND tPZH NOTE: Open drain waveforms tPLZ and tPZL are the same as those for three-state shown on the left. The test circuit is Output RL = 1k to VCC, CL = 50pF. FIGURE 9. HC AND HCT THREE-STATE PROPAGATION DELAY TEST CIRCUIT 9 PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) 5962-8780601RA ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8780601RA CD54HC299F3A 5962-8943601MRA ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8943601MR A CD54HCT299F3A CD54HC299F ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 CD54HC299F CD54HC299F3A ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8780601RA CD54HC299F3A CD54HCT299F3A ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8943601MR A CD54HCT299F3A CD74HC299E ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HC299E CD74HC299EE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HC299E CD74HC299M ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HC299M CD74HC299M96 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HC299M CD74HC299M96E4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HC299M CD74HC299M96G4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HC299M CD74HC299ME4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HC299M CD74HC299MG4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HC299M CD74HCT299E ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HCT299E CD74HCT299EE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -55 to 125 CD74HCT299E CD74HCT299M ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HCT299M Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Sep-2013 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) CD74HCT299M96 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HCT299M CD74HCT299M96E4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HCT299M CD74HCT299M96G4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HCT299M CD74HCT299ME4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HCT299M CD74HCT299MG4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 HCT299M (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF CD54HC299, CD54HCT299, CD74HC299, CD74HCT299 : * Catalog: CD74HC299, CD74HCT299 * Military: CD54HC299, CD54HCT299 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant CD74HC299M96 SOIC DW 20 2000 330.0 24.4 10.8 13.0 2.7 12.0 24.0 Q1 CD74HCT299M96 SOIC DW 20 2000 330.0 24.4 10.8 13.0 2.7 12.0 24.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CD74HC299M96 SOIC DW 20 2000 367.0 367.0 45.0 CD74HCT299M96 SOIC DW 20 2000 367.0 367.0 45.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated