910A
PHASE CONTROL THYRISTORS Hockey Puk Version
ST700C..L SERIES
1
Bulletin I25190 rev. D 04/00
www.irf.com
Features
Center amplifying gate
Metal case with ceramic insulator
International standard case TO-200AC (B-PUK)
Typical Applications
DC motor control
Controlled DC power supplies
AC controllers
IT(AV) 910 A
@ Ths 55 °C
IT(RMS) 1857 A
@ Ths 25 °C
ITSM @
50Hz 15700 A
@ 60Hz 16400 A
I2t@
50Hz 1232 KA2s
@ 60Hz 1125 KA2s
VDRM/VRRM 1200 to 2000 V
tqtypical 150 µs
TJ- 40 to 125 °C
Parameters ST700C..L Units
Major Ratings and Characteristics case style TO-200AC (B-PUK)
ST700C..L Series
2www.irf.com
Bulletin I25190 rev. D 04/00
ELECTRICAL SPECIFICATIONS
Voltage Ratings
Voltage VDRM/VRRM, max. repetitive VRSM
, maximum non- IDRM/IRRM
max.
Type number Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max
VVmA
12 1200 1300
16 1600 1700
ST700C..L 18 1800 1900 80
20 2000 2100
IT(AV) Max. average on-state current 910 (355) A 180° conduction, half sine wave
@ Heatsink temperature 55 (85) °C double side (single side) cooled
IT(RMS) Max. RMS on-state current 1857 DC @ 25°C heatsink temperature double side cooled
ITSM Max. peak, one-cycle 15700 t = 10ms No voltage
non-repetitive surge current 16400 A t = 8.3ms reapplied
13200 t = 10ms 100% VRRM
13800 t = 8.3ms reapplied Sinusoidal half wave,
I2t Maximum I2t for fusing 1232 t = 10ms No voltage Initial TJ = TJ max.
1125 t = 8.3ms reapplied
871 t = 10ms 100% VRRM
795 t = 8.3ms reapplied
I2√t Maximum I2√t for fusing 12321 KA2√s t = 0.1 to 10ms, no voltage reapplied
VT(TO)1Low level value of threshold
voltage
VT(TO)2High level value of threshold
voltage
rt1 Low level value of on-state
slope resistance
rt2 High level value of on-state
slope resistance
VTM Max. on-state voltage 1.80 V Ipk= 2000A, TJ = TJ max, tp = 10ms sine pulse
IHMaximum holding current 600
ILTypical latching current 1000
1.00 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max.
0.40 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max.
0.35 (I > π x IT(AV)),TJ = TJ max.
Parameter ST700C..L Units Conditions
1.13 (I > π x IT(AV)),TJ = TJ max.
On-state Conduction
KA2s
V
mΩ
mA TJ = 25°C, anode supply 12V resistive load
ST700C..L Series
3
www.irf.com
Bulletin I25190 rev. D 04/00
di/dt Max. non-repetitive rate of rise Gate drive 20V, 20Ω, tr ≤ 1µs
of turned-on current TJ = TJ max, anode voltage ≤ 80% VDRM
Gate current 1A, dig/dt = 1A/µs
Vd = 0.67% VDRM, TJ = 25°C
ITM = 750A, TJ = TJ max, di/dt = 60A/µs, V
R = 50V
dv/dt = 20V/µs, Gate 0V 100Ω, tp = 500µs
Parameter ST700C..L Units Conditions
Switching
1000 A/µs
tdTypical delay time 1.0
tqTypical turn-off time 150
µs
dv/dt Maximum critical rate of rise of
off-state voltage
IDRM Max. peak reverse and off-state
IRRM leakage current
Blocking
500 V/µsT
J = TJ max. linear to 80% rated VDRM
Parameter ST700C..L Units Conditions
80 mA TJ = TJ max, rated VDRM/VRRM applied
PGM Maximum peak gate power 10.0 TJ = TJ max, tp ≤ 5ms
PG(AV) Maximum average gate power 2.0 TJ = TJ max, f = 50Hz, d% = 50
IGM Max. peak positive gate current 3.0 A TJ = TJ max, tp ≤ 5ms
+VGM Maximum peak positive
gate voltage
-VGM Maximum peak negative
gate voltage
TJ = - 40°C
mA TJ = 25°C
TJ = 125°C
TJ = - 40°C
VT
J = 25°C
TJ = 125°C
IGD DC gate current not to trigger 10 mA
Parameter ST700C..L Units Conditions
20
5.0
Triggering
TYP. MAX.
200 -
100 200
50 -
2.5 -
1.8 3.0
1.1 -
VGD DC gate voltage not to trigger 0.25 V
Max. gate current/voltage not to
trigger is the max. value which
will not trigger any unit with rated
VDRM anode-to-cathode applied
TJ = TJ max
Max. required gate trigger/ cur-
rent/ voltage are the lowest value
which will trigger all units 12V
anode-to-cathode applied
VGT DC gate voltage required
to trigger
IGT DC gate current required
to trigger
W
VTJ = TJ max, tp ≤ 5ms
ST700C..L Series
4www.irf.com
Bulletin I25190 rev. D 04/00
TJMax. operating temperature range -40 to 125
Tstg Max. storage temperature range -40 to 150
RthJ-hs Max. thermal resistance, 0.073 DC operation single side cooled
junction to heatsink 0.031 DC operation double side cooled
RthC-hs Max. thermal resistance, 0.011 DC operation single side cooled
case to heatsink 0.006 DC operation double side cooled
F Mounting force, ± 10% 14700 N
(1500) (Kg)
wt Approximate weight 255 g
Parameter ST700C..L Units Conditions
K/W
°C
Case style TO - 200AC (B-PUK) See Outline Table
K/W
Thermal and Mechanical Specification
Single Side Double Side Single Side Double Side
180°0.009 0.009 0.006 0.006
120°0.011 0.011 0.011 0.011
90°0.014 0.014 0.015 0.015 K/W TJ = TJ max.
60°0.020 0.020 0.021 0.021
30°0.036 0.036 0.036 0.036
Sinusoidal conduction Rectangular conduction
Conduction angle Units Conditions
∆RthJ-hs Conduction
(The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC)
1- Thyristor
2- Essential part number
3-0 = Converter grade
4-C = Ceramic Puk
5- Voltage code: Code x 100 = VRRM (See Voltage Rating Table)
6- L = Puk Case TO-200AC (B-PUK)
7- 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads)
1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads)
2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads)
3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads)
8- Critical dv/dt: None = 500V/µsec (Standard selection)
L = 1000V/µsec (Special selection)
Ordering Information Table
Device Code
5123 4
ST 70 0 C 20 L 1
76 8
ST700C..L Series
5
www.irf.com
Bulletin I25190 rev. D 04/00
Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics
40
50
60
70
80
90
100
110
120
130
0 100 200 300 400 500 600 700
30° 60° 90°
120° 180°
Average O n-state C urrent (A)
Conduction Angle
Maximum Allowable Heatsink Temperature (°C)
ST700C ..L Series
(Sin gle Side C ooled)
R (D C ) = 0.07 3 K/W
th J-hs
20
30
40
50
60
70
80
90
100
110
120
130
0 200 400 600 800 1000
DC
30°60°
90°120°180°
Average On-state Current (A)
Conduction Period
Maxim um Allowable Heatsink Temperature (°C)
ST700C ..L Series
( S in g le Sid e C o o le d )
R (D C ) = 0.073 K/W
th J-hs
Outline Table
TWO PLACES
PIN RECEPTACLE
AMP. 60598-1
0.7 (0.03) MIN. 34 (1.34) DIA. MAX.
53 (2.09) DIA. MAX.
58 .5 (2.3 ) D IA. M AX .
2 HOLES DIA. 3.5 (0.14) x
2.5 (0.1) DEEP
4.7 (0.18)
27 (1.06) M AX .
0.7 (0.03) MIN.
6.2 (0.24) MIN.
20°± 5°
36.5 (1.44)
CREPAGE DISTANCE 36.33 (1.430) MIN.
STRIKE DISTANCE 17.43 (0.686) MIN.
Case Style TO-200AC (B-PUK)
All dimensions in millimeters (inches)
Quote between upper and lower
pole pieces has to be considered
after application of Mounting Force
(see Thermal and Mechanical
Specification)
ST700C..L Series
6www.irf.com
Bulletin I25190 rev. D 04/00
Fig. 3 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics
Fig. 5- On-state Power Loss Characteristics Fig. 6- On-state Power Loss Characteristics
Fig. 8 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled
Fig. 7 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled
20
30
40
50
60
70
80
90
100
110
120
130
0 400 800 1200 1600 2000
DC
30°60°
90°
120°
180°
Average On -state C urrent (A)
Conduction Period
Maximum Allowable Heatsink Temperature (°C)
ST 700C ..L Series
(Double Side Cooled)
R (DC ) = 0.031 K/W
thJ-hs
20
30
40
50
60
70
80
90
100
110
120
130
0 200 400 600 800 1000 1200
30°60°90°120°180°
Average On-state Current (A)
Conduction Angle
Maximum Allowable Heatsink Temperature (°C)
ST700C..L Series
(Double Side Cooled )
R (DC) = 0.031 K/W
thJ- hs
0
400
800
1200
1600
2000
2400
2800
0 200 400 600 800 1000 1200
180°
120°
90°
60°
30°
RMS Limit
Conduction Angle
Maximum Average On-state Power Loss (W)
Average On-state Current (A)
ST700C..L Series
T = 125°C
J
0
500
1000
1500
2000
2500
3000
3500
0 400 800 1200 1600 2000
DC
180°
120°
90°
60°
30°
RMS Limit
Conduction Period
Maximum Average On-state Power Loss (W)
Avera ge On -state Curren t (A)
ST700C..L Series
T = 125°C
J
6000
7000
8000
9000
10000
11000
12000
13000
14000
1 10 100
Number Of Equal Amplitude Half Cycle Current Pulses (N)
Peak Half Sine W ave On-state Current (A)
In it ia l T = 1 2 5 °C
@ 60 Hz 0.0083 s
@ 50 Hz 0.0100 s
J
ST700C ..L Series
At Any Rated Load Condition And With
Rated V Applied Following Surge.
RRM
6000
7000
8000
9000
10000
11000
12000
13000
14000
15000
16000
0.01 0.1 1
P u lse T ra in D u r a ti o n ( s )
Ve rsus Pulse Tra in D ura tion . Co ntro l
Of C onduction M ay Not Be M ain tained.
Peak Half Sine Wave On-state Current (A)
In it ia l T = 1 2 5 °C
No V oltag e Re a p p lied
Rated V Rea pplied
RRM
J
ST7 00C ..L Se rie s
M a xim um N on Re petitiv e Surg e Curre nt
ST700C..L Series
7
www.irf.com
Bulletin I25190 rev. D 04/00
Fig. 9 - On-state Voltage Drop Characteristics
Fig. 10 - Thermal Impedance ZthJ-hs Characteristics
Fig. 11 - Gate Characteristics
100
1000
10000
0.511.522.533.54
T = 25°C
J
Instan tan eous O n-state Current (A)
In stan ta ne ous On-state Volta g e (V )
T = 125°C
J
ST700C..L Series
0.001
0.01
0.1
0.001 0.01 0.1 1 10
Squa re W a ve Pulse D ur atio n (s)
thJ-hs
Steady State V alu e
R = 0.073 K/W
(Sin gle Side Cooled)
R = 0.031 K/W
(Double Side Cooled)
(D C Ope ration)
ST700C ..L Series
thJ-hs
thJ-hs
Transien t Th ermal Im pe da n ce Z (K/W)
0.1
1
10
100
0.0 01 0 .0 1 0 .1 1 10 1 00
VG D
IG D
(b)
(a)
Tj=25 °C
Tj=125 °C
Tj=-40 °C
(2) (3)
Insta nta ne ous Gate Curren t (A)
Insta nta neous G ate Voltage (V)
a) Recommended load line for
b) Re co m m e nd e d loa d line for
<=30% rated di/dt : 10V, 10 ohm s
Frequenc y Lim ite d by PG (AV)
rated d i/dt : 20V, 1 0ohm s; tr<=1 µs
tr<=1 µs
(1)
(1) PGM = 10W , tp = 4m s
(2) PGM = 20W , tp = 2m s
(3) PGM = 40W , tp = 1m s
(4) PG M = 60W , tp = 0.66ms
Rectangular gate pulse
Device : ST700C..L Series
(4)
