Silizium-PIN-Fotodiode mit sehr kurzer Schaltzeit Silicon PIN Photodiode with Very Short Switching Time Lead (Pb) Free Product - RoHS Compliant SFH 203 SFH 203 FA SFH 203 SFH 203 FA Wesentliche Merkmale Features * Speziell geeignet fur Anwendungen im Bereich von 400 nm bis 1100 nm (SFH 203) und bei 880 nm (SFH 203 FA) * Kurze Schaltzeit (typ. 5 ns) * 5 mm-Plastikbauform im LED-Gehause * Auch gegurtet lieferbar * Especially suitable for applications from 400 nm to 1100 nm (SFH 203) and of 880 nm (SFH 203 FA) * Short switching time (typ. 5 ns) * 5 mm LED plastic package * Also available on tape and reel Anwendungen Applications * Industrieelektronik * Messen/Steuern/Regeln" * Schnelle Lichtschranken fur Gleich- und Wechsellichtbetrieb * LWL * * * * Typ Type Bestellnummer Ordering Code SFH 203 Q62702P0955 SFH 203 FA Q62702P0956 2005-04-27 1 Industrial electronics For control and drive circuits Photointerrupters Fiber optic transmission systems SFH 203, SFH 203 FA Grenzwerte Maximum Ratings Bezeichnung Parameter Symbol Symbol Wert Value Einheit Unit Betriebs- und Lagertemperatur Operating and storage temperature range Top; Tstg - 40 ... + 100 C Sperrspannung Reverse voltage VR 50 V Verlustleistung Total power dissipation Ptot 150 mW Kennwerte (TA = 25 C) Characteristics Bezeichnung Parameter Symbol Symbol Wert Value Einheit Unit SFH 203 SFH 203 FA IP 80 ( 50) - A IP - 50 ( 30) A Wellenlange der max. Fotoempfindlichkeit Wavelength of max. sensitivity S max 850 900 nm Spektraler Bereich der Fotoempfindlichkeit S = 10% von Smax Spectral range of sensitivity S = 10% of Smax 400 ... 1100 800 ... 1100 nm Bestrahlungsempfindliche Flache Radiant sensitive area A 1 1 mm2 1x 1 1x 1 mm x m m Fotostrom Photocurrent VR = 5 V, Normlicht/standard light A, T = 2856 K, EV = 1000 lx VR = 5 V, = 950 nm, Ee = 1 mW/cm2 Abmessung der bestrahlungsempfindlichen Flache L x B Dimensions of radiant sensitive area Lx W Halbwinkel Half angle 20 20 Grad deg. Dunkelstrom, VR = 20 V Dark current IR 1 (5) 1 (5) nA Spektrale Fotoempfindlichkeit, = 850 nm Spectral sensitivity S 0.62 0.59 A/W Quantenausbeute, = 850 nm Quantum yield 0.89 0.86 Electrons Photon 2005-04-27 2 SFH 203, SFH 203 FA Kennwerte (TA = 25 C) Characteristics (cont'd) Bezeichnung Parameter Symbol Symbol Wert Value SFH 203 SFH 203 FA Einheit Unit Leerlaufspannung Open-circuit voltage Ev = 1000 Ix, Normlicht/standard light A, T = 2856 K Ee = 0.5 mW/cm2, = 950 nm VO 420 ( 350) - mV VO - 370 ( 300) mV Kurzschlustrom Short-circuit current Ev = 1000 Ix, Normlicht/standard light A, T = 2856 K Ee = 0.5 mW/cm2, = 950 nm ISC 80 - A ISC - 25 A Anstiegs- und Abfallzeit des Fotostromes Rise and fall time of the photocurrent RL = 50 ; VR = 20 V; = 850 nm; Ip = 800 A tr , tf 5 5 ns Durchlaspannung, IF = 80 mA, E = 0 Forward voltage VF 1.3 1.3 V Kapazitat, VR = 0 V, f = 1 MHz, E = 0 Capacitance C0 11 11 pF Temperaturkoeffizient von VO Temperature coefficient of VO TCV - 2.6 - 2.6 mV/K TCI 0.18 - - 0.2 %/K Rauschaquivalente Strahlungsleistung Noise equivalent power VR = 20 V, = 850 nm NEP 2.9 x 10- 14 2.9 x 10- 14 Nachweisgrenze, VR = 20 V, = 850 nm Detection limit D* 3.5 x 1012 3.5 x 1012 Temperaturkoeffizient von ISC Temperature coefficient of ISC Normlicht/standard light A = 950 nm 2005-04-27 3 W -----------Hz cm x Hz --------------------------W SFH 203, SFH 203 FA Relative Spectral Sensitivity SFH 203 Srel = f () Relative Spectral Sensitivity SFH 203 FA Srel = f () OHF01034 100 S rel % 80 80 60 60 40 40 20 20 0 400 600 800 1000 nm 1200 Photocurrent IP = f (Ee), VR = 5 V Open-Circuit-Voltage VO = f (Ee) SFH 203 FA P OHF01773 100 S rel % OHF01128 10 3 A 10 2 10 4 mV 10 3 VO Photocurrent IP = f (Ev), VR = 5 V Open-Circuit Voltage VO = f (Ev) SFH 203 0 400 600 800 1000 nm 1200 Dark Current IR = f (VR), E = 0 Total Power Dissipation Ptot = f (TA) OHF00394 160 mW Ptot 140 R OHF01026 10 4 pA 120 VO 10 3 100 10 1 10 2 P 10 0 80 60 10 1 10 2 40 20 10 -1 10 -3 10 -2 10 -1 10 0 mW/cm 2 10 1 Ee 0 0 20 40 60 Directional Characteristics Srel = f () 2005-04-27 4 80 C 100 TA 10 1 0 10 20 V VR 30 SFH 203, SFH 203 FA Mazeichnung Package Outlines Cathode 29 (1.142) 27 (1.063) 0.4 (0.016) 0.8 (0.031) 1.8 (0.071) 5.9 (0.232) 5.5 (0.217) o4.8 (0.189) o5.1 (0.201) 0.4 (0.016) 0.6 (0.024) 1.2 (0.047) spacing 2.54 (0.100) 9.0 (0.354) 8.2 (0.323) 7.8 (0.307) 7.5 (0.295) Area not flat 0.6 (0.024) 0.4 (0.016) 4.8 (0.189) 4.2 (0.165) Chip position GEOY6645 Mae werden wie folgt angegeben: mm (inch) / Dimensions are specified as follows: mm (inch). Lotbedingungen Soldering Conditions Wellenloten (TTW) TTW Soldering (nach CECC 00802) (acc. to CECC 00802) OHLY0598 300 C T 10 s 250 Normalkurve standard curve 235 C ... 260 C Grenzkurven limit curves 2. Welle 2. wave 200 1. Welle 1. wave 150 ca 200 K/s 2 K/s 5 K/s 100 C ... 130 C 100 2 K/s 50 Zwangskuhlung forced cooling 0 0 50 100 150 200 t 2005-04-27 5 s 250 SFH 203, SFH 203 FA Published by OSRAM Opto Semiconductors GmbH Wernerwerkstrasse 2, D-93049 Regensburg www.osram-os.com (c) All Rights Reserved. Attention please! The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components 1 may only be used in life-support devices or systems 2 with the express written approval of OSRAM OS. 1 A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system. 2 Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered. 2005-04-27 6