Series FP01 Contactless Pushbuttons
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
D
Illuminated PB
Slides Programmable Rockers
Touch Tilt Toggles
D4 www.nkkswitches.com
Distinctive Characteristics
Brilliant illumination for highly visible status indication
with LEDs and caps in red, green, or amber; subdued
illumination for low light requirements with white cap
over red, green, or amber LEDs.
Photo interrupter, rather than contacts, ensures
high reliability and long life of 3 million
operations minimum.
Rugged construction and smooth actuation allow
repeated, rapid actuation force anywhere on cap
surface.
Snap-in mounting for easy installation.
Connector socket with 6 pins for simple connection.
Well suited for gaming and vending machines, as
well as equipment exposed to corrosive gases used in
environments such as chemical or steel manufacturing plants.
Actual Size
Series FP01
Contactless Pushbuttons
D5
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
D
Illuminated PBSlides Programmable Toggles
Rockers
Touch Tilt
www.nkkswitches.com
Photo Transistor
1Single
TYPICAL SWITCH ORDERING EXAMPLE
Photo Interrupter
5Unshaded (Shaded)
(Momentary
Operating Function)
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
FP0115CAC1FF
Housing
ABlack
Round, Black Housing
Green Actuator
with Green LED
Single Photo Transistor with
Normally Unshaded
Photo Interrupter
LEDs
CRed
DAmber
FGreen
Actuator Colors
BWhite
CRed
DAmber
FGreen
FP01
Shape
CRound
Receptacle
C1 6-pin Socket
See Connector.
Connector
C2 Assembled Connector
with Wire Leads
* C3 Unassembled Connector
and Pins
No
Code No Connector
* Available in Americas only
Contact factory for custom options
1 5 C A C1 F F
HOUSING SHAPE & COLOR RECEPTACLE
Round Shape Black Housing 6-pin Socket
C1
654321
C A
Actuator Position Photo Interrupter Schematics
Model
Normal Down Unshaded Shaded LED connector pins are 5 & 6;
interrupter connector pins are
3-4 & 1-2.
FP0115
Single
Photo
Transistor
When shaded, the photo transistor momentarily activates
electrical function which signals the external device to
change its state.
ACTUATOR & INTERRUPTER
65
43
21
Normally Unshaded with
Momentary Shaded status
15
Series FP01 Contactless Pushbuttons
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
D
Illuminated PB
Slides Programmable Rockers
Touch Tilt Toggles
D6 www.nkkswitches.com
Actuator Up Actuator Down
Status of Photo Interrupter: Unshaded Shaded
Collector Current IC:0.8mA minimum 10µA maximum
Status of Photo Transistor: On Off
Output Condition of Photo Transistor: IF = 20mA & VCE = 5V
SWITCH SPECIFICATIONS
Total Travel: .079” (2.0mm)
Operating Force: 0.75 N (.169 lbf)
Mechanical Life: 3,000,000 operations minimum
Operating Temperature Range: –25°C through +50°C (–13°F through +122°F)
MECHANICAL SPECIFICATIONS
Actuator: Polyacetal Housing: Polyamide
MATERIALS
PHOTO INTERRUPTER SPECIFICATIONS
Electrical & Optical Characteristics Typical Maximum Condition
Input
Forward Voltage VF:1.3V 1.6V IF = 50mA
Reverse Current IR:10µA FR = 5V
Transmission
Collector-Emitter Saturation Voltage VCE sat: 0.4V IF = 20mA & IC = 0.1mA
Absolute Maximum Ratings
Input LED Output Photo Transistor
Typical Forward Current IF:50mA Collector-Emitter Voltage VCEO:30V
Reverse Voltage VR:5V Emitter-Collector Voltage VECO:4.5V
Power Dissipation PD:80mW Collector Current IC:30mA
Collector Dissipation PC:80mW
Circuit Design Considerations
Output of the infrared LED in the photo interrupter
decreases approximately 50% after 100,000 hours.
Recommended load resistance (RL) is 40k ~ 120kΩ
for the illustrated circuit.
(Temperature @ 25°C)
Color Red Amber Green
Maximum Forward Current IFM 30mA 25mA 25mA
Typical Forward Current IF20mA 20mA 20mA
Forward Voltage VF1.85V 2.0V 2.25V
Maximum Reverse Voltage VRM 5V 5V 5V
Current Reduction
Rate Above 25°C ∆IF
0.38mA
/°C 0.28mA
/°C 0.40mA
/°C
Ambient Temperature Range –25° ~ +50°C
C
LED COLORS & SPECIFICATIONS
Single Element LED D F
LEDs are an integral
part of the switch and
not available separately.
The electrical speci-
fications shown are
determined at a basic
temperature of 25°C.
If the source voltage
exceeds the rated
voltage, a ballast
resistor is required.
VF
I
F
R+
–
E
Anode
Cathode
R =
E – V
F
IF
Where:
R
E
VF
IF
= Resistor V
alue (Ohms)
= Source Voltage (V)
= Forward Voltage (V)
= Forward Current (A)
180
GND
V
OUT
RL
V = 5V
CC
Threshold V
oltage
VHI: 3.8V
VLO: 1.0V
1
2
3
4
Series FP01
Contactless Pushbuttons
D7
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
D
Illuminated PBSlides Programmable Toggles
Rockers
Touch Tilt
www.nkkswitches.com
ACTUATOR COLORS
BWhite CRed DAmber FGreen
(1.5)
.059
(5.0)
.197
(5.3)
.209
(21.4)
.843
(2.3)
.091
NKK P/N
This Side
TYPICAL SWITCH DIMENSIONS
FP0115CAC1FF
(19.6) Dia
.772
(26.0) Dia
1.024
654321
(22.8) Dia
.898
Terminal Connector Detail
Pin 1
(22.9) Dia
.902
(25.1)
.988
(1.1)R Typ
.043
Recommended Panel
Thickness Range:
.098” ~ .197”
(2.5mm ~ 5.0mm)
AT022
Unassembled Connector
and Pins
CONNECTOR OPTIONS
C2 AT021
Assembled Connector
with Wire Leads
C3 No Code
No Connector
Recommended connector
for assembly:
JST model number ZHR-6
Recommended crimp
connector pins:
JST model SZH-002T-P0.5
for 28-26AWG wire leads
or SZH-003T-P0.5 for
32-28AWG wire leads.
1 connector and 8 crimp connector pins
only (no wire leads provided).
Matching wire leads: 28-26AWG
Connector body: JST model ZHR-6
Crimp connector pins: JST model SZH-002T-P0.5
Wire leads: 28-26AWG; 12-inch, unstripped;
Blue for Pin 1
LEGENDS
Shaded area is printable area.
NKK Switches can provide custom legends for caps. Contact factory for more information.
Recommended Methods:
Screen Print on cap.
Epoxy based ink is recommended.
Suggested Printable Area for FP01 Cap
(16.56) Dia
.475
(19.6) Dia
(1.52) Ty
.060
ALER
T