AXA2S Enhanced robustness and EMI resistance achieved by the laser-welded double-sided metal shell (SDXC card compatible, with card jump-out and wrong insertion prevention functions) SOCKETS FOR SD MEMORY CARD (S TYPE) FEATURES Standard type Reverse type SDIO ground tab contact supported (supports SDIO) Metal shell 1. Superior EMI resistance and terminal coplanarity achieved by the double-sided metal shell The laser-welded double-sided shell has high robustness and shielding performance. Providing a ground pattern when mounting the socket is effective for EMI protection. The high resistance to reflow heat prevents the reflow process from degrading the terminal coplanarity. 2. The structures of the card detection and write protection switches prevent the card thickness from affecting the detection accuracy. The side detection system and the highly dust-resistant V notch contact structure ensure high contact reliability. 3. Equipped with the card jump-out prevention function existence 4. Card locking structure for forced ejection protection The lock pin in the metal shell prevents unwanted ejection of the card. 5. Compatible with the SDIO standard (with ground tab) Compatible with the SDIO standard, allowing use for expansion modules with an interface function APPLICATIONS * DSCs, DVCs, PDAs, handheld terminals, notebook PCs, gaming consoles, portable audio devices, etc. that use an SD card * What is V notch construction? By making contact with the edges and thus increasing the contact pressure, this product can eliminate foreign matters more effectively than conventional products. [Cross Section of Contacts] Card detection and write protect switches Metal shell <Product without a notch> (Conventional type) <V notched product> (R, S type) Movable contact Fixed contact RoHS compliant Two-point contact (edge contact) ORDERING INFORMATION AXA 2 S 3 0 2 -M 2S: Sockets for SD memory card (S type) <Board mounting direction> 6: On board mounting reverse type (outside terminal) 7: On board mounting standard type (outside terminal) <Eject type> 3: Push-push type <Standoff height> 0: Without standoff <Function> 2: Without card jump-out prevention function, with card detection switch and with write protect switch 6: With card jump-out prevention function, with card detection switch and with write protect switch <Terminal/Boss> 2: SMD terminal/Shell SMD/Without boss <Packing> P: 500 pcs. embossed tape and paper reel package x 2 reels www.honda-connectors.co.jp 1 AXA2S PRODUCT TYPES Product name Eject type Card detection switch Card jump-out prevention function Available Sockets for SD memory card (S type) Push-push type Available Not available Mounting type Part No. Standard mounting type AXA2S73062-M Reverse mounting type Standard mounting type Reverse mounting type AXA2S63062-M AXA2S73022-M Packing quantity Inner carton Outer carton Asterisk " " mark on end of Asterisk " " mark on end of Part No.; Part No.; P: 500 pieces (1 reel) P: 1,000 pieces (2 reels) (Embossed tape package) (Embossed tape package) AXA2S63022-M SPECIFICATIONS 1. Characteristics Item Rated Current Insulation resistance Specifications 0.5 A/1 terminal Signal contact portion: Max. 100m (Initial) Detection contact portion: Max. 150m (Initial) (Card detection and write protection detection) Min. 1,000M (Initial) Breakdown voltage 500V AC for 1 min. Contact resistance Electrical characteristics Vibration resistance Mechanical characteristics Lifetime characteristics Card insertion force Card removal force Insertion and removal life of card Ambient temperature Storage temperature Environmental characteristics Resistance to soldering heat Humidity tolerance (mated condition) Applicable memory card Unit weight Condition Measured based on the HP4338B measurement method of JIS C5402 Using 500V DC megger (applied for 1 min.) Rated voltage is applied for one minute and check for short circuit or damage with a detection current of 1 mA. Frequency: 10 to 2,000 Hz Acceleration: 20.0 m/s2 {2.0G} No current interruption for more than 0.1 s Max. 40N Min. 1N, Max. 40N Insertion and removal life: 10,000 times Contact resistance after testing: Signal contact portion: Max. 40m (amount of change) Detection contact portion: Max. 150m (Card detection and write protection detection) -25C to +90C Insertion and removal speed are at a rate of 600 times/hour or less. No freezing or condensation in low temperatures -40C to +90C (The allowable storage temperature is -40C to +50C if unopened from original packaging) Reflow soldering: peak temperature 250C or less Hand soldering: Soldering iron temperature 300C, 5 sec. or less Contact resistance: Signal contact portion: Max. 40m (amount of change) Detection contact portion: Max. 150m (Card detection and write protection detection) Insulation resistance: Min. 100 M SD memory card*1 2.9g No freezing or condensation in low temperatures Sockets (shell) surface temperature for using infrared reflow soldering machine MIL-STD-1344A, METHOD 1002 Temperature: 402C, Humidity: 90 to 95%RH, Test time: 500 hours Note: *1. The above characteristics cannot be guaranteed when a card other than the specified ones is used. 2. Material and surface treatment Portion Signal contact Detection contact Retention solder tab 2 Material Copper alloy Stainless steel Surface Contact portion: Ni plating on base, PdNi plating + Au flash plating Soldering portion: Ni plating on base, Au plating on surface Contact/Soldering portion: Ni plating on base, Au plating on surface Soldering portion: Ni strike, Partial Au plating www.honda-connectors.co.jp AXA2S DIMENSIONS (Unit: mm) 1. On board mounting standard type (Without standoff) Part No. AXA2S73062-M (With card jump-out prevention function) AXA2S73022-M (Without card jump-out prevention function) 1.65 *1 0.08 (Standoff dimensions) 3.725 1.40 2.70 (Signal/Detection contact and Retention solder tab) 0.10 Terminal coplanarity Circuit schematic 2.5x7=17.50 2.50 (Contact pitch) 0.60 19.00 No. 2 2.30 20.30 22.55 28.40 10.20 No. 3 No. 1 2.5x6=15.00 SD memory card 9.775 (2.10) 8.125 5.625 2.50 (Contact pitch) Card center 13.50 1.30 : Pattern forbidden area*2 2.5x7=17.500.1 1.000.05 1.20.05 10.3 max. 2.500.05 12.1 min. 1.600.05 31.35 ref. 1.650.05 2.4750.05 8 max. 10.3 min. 12.100.05 0.6 min. 1.750.05 1.750.05 31.6 ref. 20.900.05 22.200.05 1 24.450.05 (35.10) (Set condition) Pin No.9 Pin No.2 Pin No.1 2 Pin No.3 Pin No.5 Pin No.4 Pin No.8 Pin No.7 Pin No.6 3 1.30 Recommended PC board pattern (TOP VIEW) (6.00) (Eject stroke) View of set card (0.80) (Push stroke) Detailed internal view 28.15 17.3 min. 18.3 max. (24.00) 20 min. 1.100.05 0.500.05 0.500.05 1.100.05 1.350.05 2.800.05 SD memory card : Pattern insulation is recommended. (Whole area) 2.4750.05 1.550.05 2.6750.05 2.100.05 23.9250.05 3.2250.05 Recommended metal mask pattern Metal mask thickness: 120m 2.4750.05 1.750.05 1.650.05 17.500.05 (2.5x7) 9-1.000.03 1.280.05 12.100.05 2.500.05 (pitch) Metal mask opening area ratio: 80% 0.360.03 0.360.03 0.820.03 0.820.03 0.820.03 Metal mask opening area ratio: 75% 1.350.05 Open Closed 1-3 *1 Standoff dimension is the dimension that takes into account the solder resist or silk screen printing thickness on the PC board in order to preserve the dimension from the surface of the PC board to the bottom of the socket. *2 This is the pattern forbidden area. It is provided to prevent the signal contact tips from contacting the substrate surface. 20.900.05 Card detection switch 22.200.05 Card not attached Card attached Terminal number Write protect switch Write unable Write enable Open Open Open Closed 1-2 24.450.05 Card attachment condition 1.450.05 Contact status of the card detection and write protect switches 1.550.03 2.100.03 Metal mask opening area ratio: 100% 2.6750.05 23.930.03 2.100.05 3.220.03 www.honda-connectors.co.jp 3 AXA2S 2. On board mounting reverse type (Without standoff) Part No. AXA2S63062-M (With card jump-out prevention function) AXA2S63022-M (Without card jump-out prevention function) 1.65 2.5x7=17.50 2.70 (Signal/Detection contact and Retention solder tab) 0.10 Terminal coplanarity 2.50 (Contact pitch) Circuit schematic 3.725 1.40 *0.08 (Standoff dimensions) 0.60 No. 2 28.40 20.30 22.55 2.30 19.00 10.20 No. 3 No. 1 2.5x6=15.00 SD memory card 9.775 (2.10) 8.125 5.625 2.50 (Contact pitch) Card center 1.30 Recommended PC board pattern (TOP VIEW) 1.650.05 2.4750.05 1.000.05 (24.00) 2.4750.05 22.200.05 1 24.450.05 31.6 ref. 1.100.05 0.500.05 1.100.05 0.500.05 1.750.05 12.100.05 2.500.05 1.200.05 (35.10) (Set condition) Pin No.9 Pin No.2 Pin No.1 2 Pin No.3 Pin No.5 Pin No.4 Pin No.8 Pin No.7 Pin No.6 3 (6.00) (Eject stroke) (0.80) (Push stroke) 31.35 ref. 2.5x7=17.500.1 20.900.05 View of set card 1.30 1.600.05 Detailed internal view 13.50 28.15 1.750.05 : Pattern insulation is recommended. (Whole area) 2.6750.05 2.800.05 1.350.05 SD memory card 1.550.05 23.9250.05 2.100.05 3.2250.05 * Standoff dimension is the dimension that takes into account the solder resist or silk screen printing thickness on the PC board in order to preserve the dimension from the surface of the PC board to the bottom of the socket. Open Closed 1-3 Recommended metal mask pattern Metal mask thickness: 120m 1.650.05 17.500.05 (2.5x7) 1.750.03 2.500.05 (pitch) 1.280.03 9-1.000.03 2.4750.05 Metal mask opening area ratio: 80% 23.930.03 3.220.03 4 www.honda-connectors.co.jp 1.350.05 0.820.03 0.360.03 1.550.03 2.100.03 1.450.03 2.6750.03 2.100.03 0.820.03 0.360.03 Metal mask opening area ratio: 100% 0.820.03 Metal mask opening area ratio: 75% 24.450.03 Card detection switch 20.900.03 Card not attached Card attached Terminal number Write protect switch Write unable Write enable Open Open Open Closed 1-2 22.200.03 Card attachment condition 12.100.03 Contact status of the card detection and write protect switches AXA2R Enhanced robustness and EMI resistance achieved by the laser-welded double-sided metal shell (SDXC card compatible, with card jump-out and wrong insertion prevention functions) SOCKETS FOR SD MEMORY CARD (R TYPE) FEATURES Standard type Reverse type SDIO ground tab contact supported (supports SDIO) Metal shell 1. Superior EMI resistance and terminal coplanarity achieved by the double-sided metal shell The laser-welded double-sided shell has high robustness and shielding performance. Providing a ground pattern when mounting the socket is effective for EMI protection. The high resistance to reflow heat prevents the reflow process from degrading the terminal coplanarity. 2. The structures of the card detection and write protection switches prevent the card thickness from affecting the detection accuracy. The side detection system and the highly dust-resistant V notch contact structure ensure high contact reliability. 3. Equipped with the card jump-out prevention function existence 4. Card locking structure for forced ejection protection The lock pin in the metal shell prevents unwanted ejection of the card. 5. Compatible with the SDIO standard (with ground tab) Compatible with the SDIO standard, allowing use for expansion modules with an interface function APPLICATIONS * DSCs, DVCs, PDAs, handheld terminals, notebook PCs, gaming consoles, portable audio devices, etc. that use an SD card * What is V notch construction? By making contact with the edges and thus increasing the contact pressure, this product can eliminate foreign matters more effectively than conventional products. [Cross Section of Contacts] Card detection and write protect switches <Product without a notch> (Conventional type) Metal shell <V notched product> (R, S type) Movable contact Fixed contact RoHS compliant Two-point contact (edge contact) ORDERING INFORMATION AXA 2 R 3 1 -M 2R: Sockets for SD memory card (R type) <Board mounting direction> 6: On board mounting reverse type (outside terminal) 7: On board mounting standard type (outside terminal) <Eject type> 3: Push-push type <Standoff height> 0: Without standoff 3: Stand off 1.5 mm <Function> 2: Without card jump-out prevention function, with card detection switch and with write protect switch 6: With card jump-out prevention function, with card detection switch and with write protect switch <Terminal/Boss> 1: SMD terminal/With boss <Packing> T: 35 pcs. tray package x 20 trays P: 350 pcs. embossed tape and paper reel package x 2 reels www.honda-connectors.co.jp 5 AXA2R PRODUCT TYPES Product name Eject type Card jump-out prevention function Card detection switch Available Sockets for SD memory card (R type) Push-push type Available Not available Mounting type Standard mounting type Reverse mounting type Standard mounting type Reverse mounting type Standoff height (mm) Packing quantity Part No. 0 AXA2R73061-M 1. 5 AXA2R73361-M Inner carton AXA2R63061-M Asterisk " " mark on end of Part No.; AXA2R63361-M P: 350 pieces (1 reel) (Embossed tape package) AXA2R73021-M T: 35 pieces (1 tray) AXA2R73321-M (Tray package) 0 1.5 0 1.5 0 AXA2R63021-M 1.5 AXA2R63321-M Outer carton Asterisk " " mark on end of Part No.; P: 700 pieces (2 reels) (Embossed tape package) T: 700 pieces (20 trays) (Tray package) SPECIFICATIONS 1. Characteristics Item Rated Current Insulation resistance Specifications 0.5 A/1 terminal Signal contact portion: Max. 100m (Initial) Detection contact portion: Max. 150m (Initial) (Card detection and write protection detection) Min. 1,000M (Initial) Breakdown voltage 500V AC for 1 min. Contact resistance Electrical characteristics Vibration resistance Mechanical characteristics Lifetime characteristics Card insertion force Card removal force Insertion and removal life of card Ambient temperature Storage temperature Environmental characteristics Resistance to soldering heat Humidity tolerance (mated condition) Applicable memory card Unit weight Condition Measured based on the HP4338B measurement method of JIS C5402 Using 500V DC megger (applied for 1 min.) Rated voltage is applied for one minute and check for short circuit or damage with a detection current of 1 mA. Frequency: 10 to 55 Hz Acceleration: 20.0 m/s2 {2.0G} No current interruption for more than 0.1 s Max. 40N Min. 1N, Max. 40N Insertion and removal life: 10,000 times Contact resistance after testing: Signal contact portion: 40m (amount of change) Detection contact portion: Max. 150m (Card detection and write protection detection) -25C to +90C No freezing or condensation in low temperatures -40C to +90C (The allowable storage temperature is -40C to +50C if unopened from original packaging) Reflow soldering: peak temperature 250C or less Hand soldering: Soldering iron temperature 300C, 5 sec. or less Sockets (shell) surface temperature for using infrared reflow soldering machine Contact resistance: Signal contact portion: 40m (amount of change) Detection contact portion: Max. 150m (Card detection and write protection detection) Insulation resistance: Min. 100M SD memory card*1 2.9g Insertion and removal speed are at a rate of 600 times/hour or less. No freezing or condensation in low temperatures MIL-STD-1344A, METHOD 1002 Temperature: 402C, Humidity: 90 to 95%RH, Test time: 500 hours Note: *1. The above characteristics cannot be guaranteed when a card other than the specified ones is used. 2. Material and surface treatment Portion Signal contact Detection contact Retention solder tab 6 Material Copper alloy Stainless steel Surface Contact portion: Ni plating on base, PdNi plating + Au flash plating Soldering portion: Ni plating on base, Au plating on surface Contact/Soldering portion: Ni plating on base, Au plating on surface Soldering portion: Ni strike, Partial Au plating www.honda-connectors.co.jp AXA2R DIMENSIONS (Unit: mm) 1. On board mounting standard type (Without standoff) *1 0.08 (Standoff dimensions) 1.40 0.60 0.625 9.375 2.50 No. 3 No. 2 18.20 Card center No. 1 9.40 8.10 1.2 5.3 (29.80) (Signal/Detection contact) 0.10 Terminal coplanarity Circuit schematic 19.15 17.50 2.70 28.40 Part No. AXA2R73061-M (With card jump-out prevention function) AXA2R73021-M (Without card jump-out prevention function) 0.70 (14.65) 13.50 (3.40) 28.15 (2.10) (17.50) 1.650.1 SD memory card (Contact pitch) 2.500.1 (0.625) 14.55 27.95 8.100.05 10.400.05 (15.65) 7.48 1.60 10.37 8.58 12.250.05 12.450.05 1.750.05 1.550.05 (R) Through hole Recommended metal mask pattern 17.50.05 (2.5x7) 2.50.05 (pitch) 1.650.05 6.270.05 9-1.00.03 1.20.03 Metal mask opening area ratio: 80% Metal mask opening area ratio:100% 1.600.03 ) (R (R ) 0.350.03 0.820.03 0.350.03 0.820.03 5.880.05 1.310.03 1.550.03 1.750.03 1.280.03 Metal mask thickness: 120m 5.500.05 4.200.05 Open Closed 1-3 Substrate edge 14.550.05 27.950.05 *1 Standoff dimension is the dimension that takes into account the solder resist or silk screen printing thickness on the PC board in order to preserve the dimension from the surface of the PC board to the bottom of the socket. *2 This is the pattern forbidden area. It is provided to prevent the signal contact tips from contacting the substrate surface. (3.9) Card detection switch 26.400.05 3.300.03 14.300.05 Card not attached Card attached Terminal number Write protect switch Write unable Write enable Open Open Open Closed 1-2 0.600.05 0.400.05 1.600.05 (0.50) 5.300.05 1.400.05 1.600.05 3.30 ) Socket edge Card attachment condition 1.600.05 0.600.05 0.400.05 (R PC board both side Contact status of the card detection and write protect switches : Pattern forbidden area*2 1.200.05 0.500.05 1.100.05 0.500.05 1.100.05 1.60 SD memory card 2.500.05 (Pitch) : Pattern insulation is recommended. (Whole area) 2.10 (24.00) 30.300.05 18.200.05 1 (30.15) 19.150.05 17.500.05 0.6250.05 1.000.05 9.400.05 8.100.05 Pin No.1 Pin No.3 Pin No.2 Pin No.9 2 Pin No.4 Pin No.5 Pin No.6 Pin No.8 Pin No.7 3 Recommended PC board pattern (TOP VIEW) 1.600.05 View of set card (0.80) (Push stroke) (6.00) (Eject stroke) (35.10) (Set condition) Detailed internal view Socket edge 1.600.03 29.950.05 Metal mask opening area ratio: 75% www.honda-connectors.co.jp 7 AXA2R 2. On board mounting standard type (Standoff 1.5mm) 19.15 17.50 2.70 1.40 *1.58 (Standoff dimensions) (Signal/Detection contact) 0.10 Terminal coplanarity 0.60 0.625 Circuit schematic 9.375 2.50 (29.80) No. 3 28.40 Part No. AXA2R73361-M (With card jump-out prevention function) AXA2R73321-M (Without card jump-out prevention function) 18.20 9.40 8.10 1.2 1.7 5.3 No. 2 13.50 (4.90) No. 1 Card center 0.7 14.65 28.15 1.650.1 (2.10) (17.50) (Contact pitch) 2.500.1 (0.625) SD memory card 14.55 27.95 1.600.05 19.150.05 17.500.05 0.6250.05 1.200.05 1.750.05 1.550.05 12.250.05 12.450.05 1.600.05 0.600.05 0.400.05 (R (0.50) 5.300.05 1.400.05 1.600.05 3.30 ) (R ) SD memory card 0.500.05 1.100.05 0.500.05 1.100.05 (24.00) 2.500.05 (Pitch) 1.000.05 9.400.05 8.100.05 1 30.300.05 Pin No.1 Pin No.3 Pin No.2 Pin No.9 2 Pin No.4 Pin No.5 Pin No.6 Pin No.8 Pin No.7 3 Recommended PC board pattern (TOP VIEW) 18.200.05 View of set card (0.80) (Push stroke) (6.00) (Eject stroke) (35.10) (Set condition) Detailed internal view Socket edge PC board both side Card attachment condition Card not attached Card attached Terminal number Write protect switch Write unable Write enable Open Open Open Closed 1-2 Card detection switch Substrate edge 14.550.05 27.950.05 Through hole * Standoff dimension is the dimension that takes into account the solder resist or silk screen printing thickness on the PC board in order to preserve the dimension from the surface of the PC board to the bottom of the socket. Open Closed 1-3 Recommended metal mask pattern Metal mask thickness: 120m 17.50.05 (2.5x7) 2.50.05 (pitch) 1.650.05 1.20.03 Metal mask opening area ratio: 80% Metal mask opening area ratio:100% ) 5.500.05 4.200.05 0.350.03 0.820.03 0.350.03 0.820.03 5.880.05 1.310.03 1.550.03 1.750.03 1.600.03 ) (R (R (3.9) 26.400.05 3.300.03 14.300.05 6.270.05 9-1.00.03 1.280.03 Contact status of the card detection and write protect switches 0.600.05 0.400.05 1.600.05 Socket edge 1.600.03 29.950.05 Metal mask opening area ratio: 75% 8 www.honda-connectors.co.jp AXA2R 3. On board mounting reverse type (Without standoff) 19.15 17.50 2.50 0.625 9.375 1.40 Part No. AXA2R63061-M (With card jump-out prevention function) AXA2R63021-M (Without card jump-out prevention function) *0.08 (Standoff dimensions) (3.40) 2.70 Circuit schematic (Signal/Detection contact) 0.10 Terminal coplanarity No. 3 (29.80) 28.40 0.60 0.70 14.65 13.50 28.15 17.50 (Contact pitch) 2.500.1 No. 1 5.30 8.10 9.40 Card center 1.20 1.70 18.20 No. 2 (2.10) SD memory card 1.650.1 (0.625) 14.55 27.95 (30.15) 19.150.05 17.500.05 0.6250.05 : Pattern insulation is recommended. (Whole area) 1.000.05 (15.65) 1 1.600.05 0.600.05 0.400.05 Through hole PC board both side * Standoff dimension is the dimension that takes into account the solder resist or silk screen printing thickness on the PC board in order to preserve the dimension from the surface of the PC board to the bottom of the socket. Open Closed 1-3 Recommended metal mask pattern 1.280.03 Metal mask thickness: 120m 17.50.05 (2.5x7) 2.50.05 (pitch) 1.650.05 9-1.00.03 Metal mask opening area ratio: 100% 5.880.05 1.310.03 1.550.03 1.750.03 (R ) 1.600.03 Socket edge 26.400.05 6.270.05 Metal mask opening area ratio: 80% 4.200.05 5.500.05 14.300.05 Card detection switch ) Card not attached Card attached Terminal number Write protect switch Write unable Write enable Open Open Open Closed 1-2 Socket edge 0.600.05 Substrate edge 0.400.05 14.550.05 1.600.05 27.950.05 (R Card attachment condition ) (R (3.9) 3.300.03 Contact status of the card detection and write protect switches 12.450.05 1.550.05 (R) 3.30 1.600.05 1.400.05 5.300.05 (0.50) SD memory card 1.20.03 (24.00) 12.250.05 1.750.05 1.600.05 8.100.05 9.400.05 18.200.05 30.300.05 2.500.05 (Pitch) 0.820.03 0.350.03 0.820.03 0.350.03 Pin No.2 Pin No.1 Pin No.3 Pin No.9 2 Pin No.4 Pin No.5 Pin No.6 Pin No.8 Pin No.7 3 Recommended PC board pattern (TOP VIEW) 1.100.05 0.500.05 1.100.05 0.500.05 1.200.05 View of set card (0.80) (Push stroke) (6.00) (Eject stroke) (35.10) (Set condition) Detailed internal view 1.600.03 29.950.05 Metal mask opening area ratio: 75% www.honda-connectors.co.jp 9 AXA2R 4. On board mounting reverse type (Standoff 1.5mm) 19.15 17.50 2.50 0.625 9.375 1.40 Part No. AXA2R63361-M (With card jump-out prevention function) AXA2R63321-M (Without card jump-out prevention function) (4.90) *1.58 (Standoff dimensions) 2.70 Circuit schematic (Signal/Detection contact) 0.10 Terminal coplanarity No. 3 (29.80) 28.40 0.60 0.70 14.65 13.50 No. 1 5.30 Card center 8.10 9.40 18.20 1.20 1.70 No. 2 (2.10) 28.15 SD memory card 17.50 (Contact pitch) 2.500.1 1.650.1 (0.625) 14.55 27.95 1 (24.00) 1.000.05 1.600.05 0.600.05 0.400.05 Card attachment condition Card detection switch 12.450.05 1.550.05 ) (R Socket edge 0.600.05 Substrate edge 0.400.05 14.550.05 1.600.05 27.950.05 Through hole PC board both side * Standoff dimension is the dimension that takes into account the solder resist or silk screen printing thickness on the PC board in order to preserve the dimension from the surface of the PC board to the bottom of the socket. Open Closed 1-3 Recommended metal mask pattern Metal mask thickness: 120m 1.280.03 Card not attached Card attached Terminal number Write protect switch Write unable Write enable Open Open Open Closed 1-2 12.250.05 1.750.05 (R) Contact status of the card detection and write protect switches 1.600.05 2.500.05 (Pitch) 3.30 1.600.05 1.400.05 5.300.05 (0.50) SD memory card 19.150.05 17.500.05 0.6250.05 8.100.05 9.400.05 18.200.05 30.300.05 Pin No.2 Pin No.1 Pin No.3 Pin No.9 2 Pin No.4 Pin No.5 Pin No.6 Pin No.8 Pin No.7 3 Recommended PC board pattern (TOP VIEW) 1.100.05 0.500.05 1.100.05 0.500.05 1.200.05 View of set card (0.80) (Push stroke) (6.00) (Eject stroke) (35.10) (Set condition) Detailed internal view 17.50.05 (2.5x7) 2.50.05 (pitch) 1.650.05 9-1.00.03 ) (R ) (R 1.600.03 Socket edge (3.9) 3.300.03 4.200.05 5.500.05 14.300.05 1.20.03 0.820.03 0.350.03 0.820.03 0.350.03 Metal mask opening area ratio: 100% 5.880.05 1.310.03 1.550.03 1.750.03 1.600.03 29.950.05 Metal mask opening area ratio: 75% 10 www.honda-connectors.co.jp 26.400.05 6.270.05 Metal mask opening area ratio: 80% AXA2S/AXA2R EMBOSSED TAPE AND REEL (Unit: mm) * Tape dimensions <S type> <R type> Socket for SD memory card (R type) Socket for SD memory card (S type) Pull-out direction (4.00) (2.00) 55 0 18 to 0 18 to 1. 5 16 5 16 Pocket pitch=36.00 Top cover tape (2.00) (4.00) Top cover tape 1.5 5 0.0 5d 0 .0 5 20.20 (1.75) 20.20 di (1.75) ia. Pull-out direction Emboss carrier tape Pocket pitch=36.00 Emboss carrier tape 40.40 44.00 a. 40.40 44.00 * Reel dimensions (Conforming to JIS C0806-1) <S and R type> Taping reel (44.4)+20 Top cover tape 370 dia. Tape Emboss carrier tape Cavity Label NOTES 1.Regarding the design of PC board patterns Conduct the recommended foot pattern design, in order to preserve the mechanical strength of terminal solder areas. 2. Regarding the socket mounting 1) When reflow soldering when the slider is locked, heat will cause the slider to deform and not work. Therefore, please confirm that the slider lock is released before mounting if you have inserted and removed a card before soldering. 2) Be aware that during mounting, external forces may be applied to the connector contact surfaces and terminals and cause deformations. 3. Soldering 1) Reflow soldering * Screen-printing method is recommended for cream solder printing. * Use the recommended foot pattern for cream solder printing (screen thickness: 0.12 mm). * The metal mask opening ratio for the Com contact (one) and No contacts (two) must be 75%. * When applying the different thickness of a screen, please consult us. * The following diagram shows the recommended reflow soldering temperature profile. The recommended conditions for the reflow temperature profile Temperature 250C max. Peak temperature 180 to 200C 155 to 165C Preheating 60 to 120 sec. Within 30 sec. Time * Measure the temperature at the connector surface. * If the reverse side of the board undergoes reflow soldering after the socket is reflow-soldered, fix the socket with tape or adhesive; otherwise, the socket may drop. The socket can withstand two iterations of reflow soldering. 2) Hand soldering * Set the soldering tip to 300C, and solder for no more than 5 seconds. * Be aware that for the 0 mm standoff type, solder creeping at the retention solder tab sections may occur if soldering is conducted for long periods or if too much solder is used. 4. Cleaning after soldering Inside the socket there is a slider section and card detection contact/write protection mechanism. If anything such as flux remains inside after washing, insertion and removal will be hampered and contact will be faulty. Therefore, do not use methods that involve submersion when cleaning. (Partial cleaning of the PC board and soldered terminals is possible.) 5. After PC board mounting 1) Warping of the PC board should be no more than 0.03 mm for the entire connector length. 2) When assembling PC boards or storing them in block assemblies, make sure that undue weight is not exerted on a stacked socket. 3) Be sure not to allow external pressure to act on sockets when assembling PC boards or moving in block assemblies. 6. Handling single components 1) Make sure not to drop or allow parts to fall from work bench 2) Be cautious when handling because excessive force applied to the terminals will cause deformation and loss of terminal coplanarity. 3) Repeated bending of the terminals may break them. www.honda-connectors.co.jp 11 AXA2S/AXA2R 7. Card fitting 1) These products are made for the design of compact and lightweight devices and therefore the molded part is very thin. For this reason, design the device to prevent undue wrenching forces from being applied to the product during use. 2) The sockets are constructed to prevent reverse card insertion. Caution is required because repeated, mistaken reverse insertion may damage the socket and card. 3) When not soldered, be careful not to insert and remove the socket's card. Doing so will cause a decrease in anchoring ability of the molded part and loss of coplanarity. 4) Forcibly removing a fitted card may degrade the card removal prevention lock. To remove a card, be sure to push the card in the insertion direction to release the slider lock before pulling out the card. 5) Please include notes to the following effect in your user manuals. 6) The card ejection protection lock does not work for MMC. 7) The socket does not have a wrong insertion protection structure for MMC. Be careful about the insertion direction. 8) If an MMC is inserted, it is possible that a short circuit between the socket's signal contacts No. 7 and 8 and the MMC's contact No. 7 may be caused. 8. Device design 1) Contact failure may result if dust or dirt enters the contact section. Please take appropriate measures when designing the device to prevent this from happening, for example by adding a cover. 2) To ensure smooth insertion and removal of cards, please design the chassis so that no force is applied to the metal shell on top of the socket. If a force is present that pushes down on the metal shell, the card will be pressed, which might prevent ejection. 3) Please provide a guide or similar to keep the socket from having force applied to it when inserting and removing. 9. Card jump-out prevention function 1) This socket has a card jump-out prevention function that works under defined conditions. However, we strongly recommend that you instruct users to carefully handle the product to avoid accidents due to improper use or product liability risks. 2) The life of the card jump-out prevention function is not guaranteed under the following conditions: (1) while the card is inserted incompletely, (2) while the card is inserted in the wrong direction, and (3) after the card is inserted in the wrong direction 3) In order to prevent card jump-out, resistance has been added that affects card insertion and removal. Therefore, you will feel resistance when inserting and removing the card. This is normal. 10. Others If you coat the PC board after soldering for insulation and to prevent wear, make sure that the coating does not adhere to the connector. Address : 6-18-12, Megurohoncho, Meguro-Ku, Tokyo 152-8520, Japan / Telephone : +81-3-3714-1166/1161 / Fax : +81-3-5721-7090 12 Specifications are subject to change without notice. www.honda-connectors.co.jp Printed in Japan