LM48823 Mono, Bridge-Tied Load, Ceramic Speaker Driver with I2C Volume Control and Reset General Description Key Specifications The LM48823 is a single supply, mono, ceramic speaker driver with an integrated charge-pump, designed for portable devices, such as cell phones, where board space is at a premium. The LM48823 charge pump allows the device to deliver 5.4VRMS from a single 4.2V supply. The LM48823 features high power supply rejection ratio (PSRR), 93dB at 217Hz, allowing the device to operate in noisy environments without additional power supply conditioning. Flexible power supply requirements allow operation from 2.0V to 4.5V. The LM48823 features an active low reset input that reverts the device to its default state. Additionally, the LM48823 features a 32-step I2C volume control. The low power Shutdown mode reduces supply current consumption to 0.01A. The LM48823's superior click and pop suppression eliminates audible transients on power-up/down and during shutdown. The LM48823 is available in an ultra-small 16-bump micro SMD package (2mmx2mm). Output Voltage at VDD = 4.2V, RL = 2.2F + 15 THD+N 1% 5.4VRMS (typ) Quiescent Power Supply Current at 4.2V PSRR at 217Hz Shutdown current 3.3mA (typ) 93dB (typ) 0.01A (typ) Features Integrated Charge Pump Bridge-tied Load Output High PSRR I2C Volume and Mode Control Reset Input Advanced Click-and-Pop Suppression Low Supply Current Minimum external components Micro-power shutdown Available in space-saving 16-bump SMD package Applications Cell phones Smart phones Portable media devices Notebook PCs Boomer(R) is a registered trademark of National Semiconductor Corporation. Tru-GND is a trademark of National Semiconductor Corporation. (c) 2008 National Semiconductor Corporation 300684 www.national.com LM48823 Mono, Bridge-Tied Load, Ceramic Speaker Driver with I2C Volume Control and Reset July 16, 2008 LM48823 Typical Application 300684e1 FIGURE 1. Typical Audio Amplifier Application Circuit www.national.com 2 LM48823 Connection Diagrams TL Package 2mm x 2mm x 0.8mm 16-Bump micro SMD Marking 300684g7 Top View XY - Date Code TT - Lot Traceability G - Boomer Family K6 - LM48823TL 300684e0 Top View See NS Package Number TLA1611A Ordering Information Order Number Package Package DWG # Transport Media MSL Level Green Status LM48823TL 16-Bump micro SMD LM48823TLX 16-Bump micro SMD TLA1611A 250 units on tape and reel 1 NOPB TLA1611A 3000 units on tape and reel 1 NOPB 3 www.national.com LM48823 TABLE 1. Bump Descriptions Pin Designator Pin Function A1 SVDD Signal Power Supply A2 SGND Signal Ground A3 BYPASS Amplifier Reference Bypass A4 INA B1 OUTA Amplifier Inverting output A B2 OUTB Amplifier Non-Inverting Output B B3 RESET Active Low Reset Input. Connect to VDD for normal operation. Toggle between VDD and GND to reset the device. Amplifier Inverting input A B4 INB Amplifier Non-Inverting Input B C1 VSS Charge Pump Output C2 SCL I2C Serial Clock Input SDA I2C Serial Data Input C3 C4 www.national.com Pin Name I2CV I2C Supply Voltage DD D1 C1N Charge Pump Flying Capacitor Negative Terminal D2 PGND D3 C1P Charge Pump Flying Capacitor Positive Terminal D4 PVDD Power Supply Power Ground 4 JA (typ) - (TLA1611A) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (Note 1) Storage Temperature Input Voltage Power Dissipation (Note 3) ESD Rating (Note 4) ESD Rating (Note 5) Junction Temperature 63.2C/W Operating Ratings Temperature Range 5.25V -65C to +150C -0.3V to VDD +0.3V Internally Limited 8kV 250V 150C TMIN TA TMAX Supply Voltage PVDD and SVDD -40C TA +85C 2.0V VDD 4.5V 1.8V I2CVDD 4.5V I2CVDD Audio Amplifier Electrical Characteristics VDD = 4.2V (Notes 1, 2) The following specifications apply for AV = 6dB, RL = 2.2F+15, C1 = C2 = 2.2F, f = 1kHz, unless otherwise specified. Limits apply for TA = 25C. LM48823 Symbol Parameter Conditions Typical (Note 6) Limits (Note 7) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, RL = 3.3 4.3 mA (max) ISD Shutdown Current Shutdown Enabled 0.01 1 A (max) VOS Differential Output Offset Voltage VIN = 0V 0.5 3 mV (max) VIH Logic High Input Threshold RESET 1.4 V (min) 0.4 V (max) VIL AV RIN RESET Gain Minimum Gain Setting -70 dB Maximum Gain Setting 24 dB Maximum Gain Setting 9 7 11 k (min) k (max) Minimum Gain Setting 80 64 96 k (min) k (max) RL = 2.2F+15, THD+N = 1% f = 1kHz f = 5kHz 5.4 3.1 VRMS VRMS 0.015 % Input Resistance VO Output Voltage THD+N Total Harmonic Distortion + Noise PSRR Power Supply Rejection Ratio SNR VO = 4VRMS VRIPPLE = 200mVP-P Sine, Inputs AC GND, CIN = 1F, input referred f = 217Hz f = 1kHz 93 93 Signal-to-Noise-Ratio POUT = 40mW, RL = 16 f = 1kHz 119 dB OS Output Noise AV = 4dB, Input Referred, A-weighted Filter 5.5 V TWU Wake-Up Time 200 s 5 82 dB (min) dB www.national.com LM48823 Thermal Resistance Absolute Maximum Ratings (Notes 1, 2) LM48823 I2C Interface Characteristics VDD = 3.0V (Notes 1, 2) The following specifications apply for AV = 6dB, RL = 2.2F+15, C1 = C2 = 2.2F, f = 1kHz, unless otherwise specified. Limits apply for TA = 25C. LM48823 Symbol Parameter Conditions Typical (Note 6) Limits (Note 7) Units (Limits) t1 SCL period 2.5 s (min) t2 SDA Setup Time 100 ns (min) t3 SDA Stable Time 0 ns (min) t4 Start Condition Time 100 ns (min) t5 Stop Condition Time 100 ns (min) VIH Logic High Input Threshold 0.7 x I2CVDD V (min) Logic Low Input Threshold 0.3 x I2CVDD V (max) VIL Note 1: :. "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA) / JA or the number given in Absolute Maximum Ratings, whichever is lower. Note 4: Human body model, applicable std. JESD22-A114C. Note 5: Machine model, applicable std. JESD22-A115-A. Note 6: Typical values represent most likely parametric norms at TA = +25C, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 7: Datasheet min/max specification limits are guaranteed by test or statistical analysis. www.national.com 6 LM48823 Typical Performance Characteristics THD+N vs Frequency VDD = 3.6V THD+N vs Frequency VDD = 4.2V 300684g9 300684h0 THD+N vs Output Voltage AV = 6dB, ZL = 1F+15, f = 1kHz THD+N vs Output Voltage AV = 6dB, ZL = 2.2F+15, f = 1kHz 300684f2 300684f3 Output Voltage vs Frequency VDD = 4.2V, ZL = 1F+15,THD+N = 1% Output Voltage vs Frequency VDD = 4.2V, ZL = 2.2F+15,THD+N = 1% 300684f6 300684f7 7 www.national.com LM48823 Power Consumption vs Output Voltage VDD = 3.6V, ZL = 1F+15 Power Consumption vs Output Voltage VDD = 3.6V, ZL = 2.2F+15 300684f9 300684f8 Power Consumption vs Output Voltage VDD = 4.2V, ZL = 1F+15 Power Consumption vs Output Voltage VDD = 4.2V, ZL = 2.2F+15 300684g0 300684g1 Output Voltage vs Supply Voltage ZL = 1F+15, THD+N = 1% Output Voltage vs Supply Voltage ZL = 2.2F+15, THD+N = 1% 300684g2 www.national.com 300684g3 8 LM48823 PSRR vs Frequency VDD = 4.2V, VRIPPLE = 200mVP-P ZL = 1F+15, Input referred Supply Current vs Supply Voltage No Load 300684g5 300684g4 Shutdown Current vs Supply Voltage No Load 300684g6 9 www.national.com LM48823 Application Information The 7-bit device address is written to the bus, most significant bit (MSB) first, followed by the R/W bit. R/W = 0 indicates the master is writing to the slave device, R/W = 1 indicates the master wants to read data from the slave device. Set R/W = 0; the LM48823 is a WRITE-ONLY device and will not respond to the R/W = 1. The data is latched in on the rising edge of the clock. Each address bit must be stable while SCL is HIGH. After the last address bit is transmitted, the master device releases SDA, during which time, an acknowledge clock pulse is generated by the slave device. If the LM48823 receives the correct address, the device pulls the SDA line low, generating an acknowledge bit (ACK). Once the master device registers the ACK bit, the 8-bit register data word is sent. Each data bit should be stable while SCL is HIGH. After the 8-bit register data word is sent, the LM48823 sends another ACK bit. Following the acknowledgement of the register data word, the master issues a STOP bit, allowing SDA to go high while SCL is high. I2C COMPATIBLE INTERFACE The LM48823 is controlled through an I2C compatible serial interface that consists of a serial data line (SDA) and a serial clock (SCL). The clock line is uni-directional. The data line is bi-directional (open drain). The LM48823 and the master can communicate at clock rates up to 400kHz. Figure 2 shows the I2C interface timing diagram. Data on the SDA line must be stable during the HIGH period of SCL. The LM48823 is a transmit/receive slave-only device, reliant upon the master to generate the SCL signal. Each transmission sequence is framed by a START condition and a STOP condition (Figure 3). Each data word, device address and data, transmitted over the bus is 8 bits long and is always followed by an acknowledge pulse (Figure 4). The LM48823 device address is 1110110. I2C BUS FORMAT The I2C bus format is shown in Figure 4. The START signal, the transition of SDA from HIGH to LOW while SCL is HIGH, is generated, alerting all devices on the bus that a device address is being written to the bus. 30068467 FIGURE 2. I2C Timing Diagram 300684g8 FIGURE 3. Start and Stop Diagram www.national.com 10 LM48823 300684e2 FIGURE 4. Example Write Sequence TABLE 2. Device Address Chip Address B7 B6 B5 B4 B3 B2 B1 B0 R/W 1 1 1 0 1 1 0 0 TABLE 3. Mode Control Registers Register Name B7 B6 B5 B4 B3 B2 B1 B0 Mode Control VOL4 VOL3 VOL2 VOL1 VOL0 0 ENABLE_A ENABLE_B GENERAL AMPLIFIER FUNCTION The LM48823 is a ceramic speaker driver that utilizes National's inverting charge pump technology to deliver over 15VP-P to a 2.2F ceramic speaker while operating from a single 4.2V supply. The LM48823 features a unique input stage that converts two single-ended audio signals into a mono BTL output. This stereo to mono conversion is useful in applications where a stereo audio source is driving a single ceramic speaker, such as a ringer on a cellular phone. Connect INA and INB as shown in Figure 5 for the stereo-to-mono conversion. When the LM48823 is used with a single-ended mono audio source, connect both INA and INB to the audio source as shown in Figure 6. 300684e4 FIGURE 5. Stereo to Mono Conversion Connection Example 300684e3 FIGURE 6. Mono Audio Source Connection Example 11 www.national.com LM48823 VOLUME CONTROL TABLE 4. Volume Control Volume Step VOL4 VOL3 VOL2 VOL1 VOL0 Gain (dB) 1 0 0 0 0 0 -70 2 0 0 0 0 1 -56 3 0 0 0 1 0 -46 4 0 0 0 1 1 -38 5 0 0 1 0 0 -32 6 0 0 1 0 1 -28 7 0 0 1 1 0 -24 8 0 0 1 1 1 -21 9 0 1 0 0 0 -18 10 0 1 0 0 1 -15 11 0 1 0 1 0 -12 12 0 1 0 1 1 -10 13 0 1 1 0 0 -8 14 0 1 1 0 1 -6 15 0 1 1 1 0 -4 16 0 1 1 1 1 -2 17 1 0 0 0 0 0 18 1 0 0 0 1 2 19 1 0 0 1 0 4 20 1 0 0 1 1 6 21 1 0 1 0 0 8 22 1 0 1 0 1 10 23 1 0 1 1 0 12 24 1 0 1 1 1 16 25 1 1 0 0 0 14 26 1 1 0 0 1 15 27 1 1 0 1 0 16 28 1 1 0 1 1 17 29 1 1 1 0 0 18 30 1 1 1 0 1 22 31 1 1 1 1 0 23 32 1 1 1 1 1 24 www.national.com 12 Charge Pump Hold Capacitor (C2) The value and ESR of the hold capacitor (C2) directly affects the ripple on CPVSS. Increasing the value of C2 reduces output ripple. Decreasing the ESR of C2 reduces both output ripple and charge pump output impedance. A lower value capacitor can be used in systems with low maximum output power requirements. RESET The LM48823 features an active low reset input. Driving RESET low clears the I2C register. Volume control is set to 00000 (-70dB) and both ENABLE_A and ENABLE_B are set to 0, disabling the device. While RESET is low, the LM48823 ignores any I2C data. After the device is reset, and RESET is driven high, the LM48823 remains in shutdown mode with the volume set to -70dB. Re-enable the device by writing to the I2C register. Input Capacitor Selection Input capacitors block the DC component of the audio signal, eliminating any conflict between the DC component of the audio source and the bias voltage of the LM48823. The input capacitors create a high-pass filter with the input resistors RIN. The -3dB point of the high pass filter is found using Equation (1) below. PROPER SELECTION OF EXTERNAL COMPONENTS Power Supply Bypassing/Filtering Proper power supply bypassing is critical for low noise performance and high PSRR. Place the supply bypass capacitors as close to the device as possible. Place a 1F ceramic capacitor from VDD to GND. Additional bulk capacitance may be added as required. f = 1 / 2RINCIN (Hz) (1) Where the value of R IN is given in the Electrical Characteristics Table. Bypass Capacitor Selection The BYPASS capacitor, CBYPASS, improves PSRR, noise rejection and output offset. For best results, use a capacitor of identical value to the input coupling capacitors High pass filtering the audio signal helps protect the speakers. When the LM48823 is using a single-ended source, power supply noise on the ground is seen as an input signal. Setting the high-pass filter point above the power supply noise frequencies, 217Hz in a GSM phone, for example, filters out the noise such that it is not amplified and heard on the output. Capacitors with a tolerance of 10% or better are recommended for impedance matching and improved CMRR and PSRR. Charge Pump Capacitor Selection Use low ESR ceramic capacitors (less than 100m) for optimum performance. Charge Pump Flying Capacitor (C1) The flying capacitor (C1) affects the load regulation and output impedance of the charge pump. A C1 value that is too low 13 www.national.com LM48823 results in a loss of current drive, leading to a loss of amplifier headroom. A higher valued C1 improves load regulation and lowers charge pump output impedance to an extent. Above 2.2F, the RDS(ON) of the charge pump switches and the ESR of C1 and C2 dominate the output impedance. A lower value capacitor can be used in systems with low maximum output power requirements. SHUTDOWN FUNCTION The LM48823 features a low-power shutdown mode that disables the device, lowering the quiescent current to 0.01A. Set bits B1 (ENABLE_A) and B2 (ENABLE_B) to 0 to disable the amplifiers and charge pump. Set both ENABLE_A and ENABLE_B to 1 for normal operation. Shutdown mode does not clear the I2C register. When re-enabled, the device returns to its previous volume setting. To clear the I2C register, either remove power from the device, or toggle RESET (see RESET section). LM48823 improves audio performance, minimizes crosstalk between channels and prevents switching noise from interfering with the audio signal. Use of power and ground planes is recommended. Place all digital components and route digital signal traces as far as possible from analog components and traces. Do not run digital and analog traces in parallel on the same PCB layer. If digital and analog signal lines must cross either over or under each other, ensure that they cross in a perpendicular fashion. PCB Layout Guidelines Minimize trace impedance of the power, ground and all output traces for optimum performance. Voltage loss due to trace resistance between the LM48823 and the load results in decreased output power and efficiency. Trace resistance between the power supply and ground has the same effect as a poorly regulated supply, increased ripple and reduced peak output power. Use wide traces for power supply inputs and amplifier outputs to minimize losses due to trace resistance, as well as route heat away from the device. Proper grounding LM48823TL Demoboard Bill of Materials Designator Quantity Description C1, C2 2 2.2F 10% 10V X5R Ceramic Capacitor (603) Panasonic ECJ-1VB1A225K Murata GRM033R6OJ104KE19D C3 - C5 3 1F 10% 10V Tantalum Capacitor (402) AVX TACK105M010QTA C6 1 4.7F 10% 6.3V X5R Ceramic Capacitor (603) Panasonic ECJ-1VB0J475K Murata GRM188R6OJ475KE19D C7, C8 2 0.1F 10% 6.3V X5R Ceramic Capacitor (201) Panasonic ECJZEB0J104K Murata GRM188R61A225KE34D JU1 - JU5 5 2 Pin Header JU6, JU7 3 2 Pin Header J1 1 5-Pin I2C Header LM4823TL 1 LM48823TL (16-Bump microSMD) www.national.com 14 FIGURE 7. LM48823 Demo Board Schematic 300684e5 LM48823 Demo Board Schematic 15 www.national.com LM48823 PC Board Layout 300684f1 300684f0 FIGURE 9: Top Layer FIGURE 8: Top Silkscreen Layer 300684e8 300684e7 FIGURE 11: Layer 3 FIGURE 10: Layer 2 300684e9 300684e6 FIGURE 13: Bottom Silkscreen FIGURE 12: Bottom Layer www.national.com 16 LM48823 Revision History Rev Date 1.0 06/27/08 Initial release. Description 1.01 07/15/08 Edited the Ordering Information table. 17 www.national.com LM48823 Physical Dimensions inches (millimeters) unless otherwise noted 16-Bump micro SMD Order Number LM48823TL NS Package Number TLA1611A X1 = 1.970 0.03 X2 = 1.970 0.03 X3 = 0.6 0.075 www.national.com 18 LM48823 Notes 19 www.national.com LM48823 Mono, Bridge-Tied Load, Ceramic Speaker Driver with I2C Volume Control and Reset Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com