EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Chip LED with Right Angle Lens 12-21/Y2C-AL2N1LY/2C Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mono-color type. Pb-free. RoHS refer to SMD B type SGS report The product itself will remain within RoHS compliant version. Descriptions The 12-21 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications etc. Applications Automotive: backlighting in dashboard and switch. Telecommunication: Indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Indoor signboard use. Device Selection Guide Part No. 12-21/Y2C-AL2N1LY/2C Chip Material Emitted Color AlGaInP Brilliant Yellow Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Lens Color Water Clear Rev.2 Page: 1 of10 Prepared by:Denghuadong EVERLIGHT ELECTRONICS CO.,LTD. 12-21/Y2C-AL2N1LY/2C Package Outline Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Rev.2 Page: 2 of10 Prepared by:Denghuadong EVERLIGHT ELECTRONICS CO.,LTD. 12-21/Y2C-AL2N1LY/2C Absolute Maximum Ratings (Ta=25) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40 ~ +90 Electrostatic Discharge ESD 2000 V Power Dissipation Pd 60 mW IFP 60 mA Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 for 10 sec. Soldering Temperature Tsol Hand Soldering : 350 for 3 sec. Electro-Optical Characteristics (Ta=25) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity IV 14.5 ----- 36.0 mcd Peak Wavelength p ---- 591 ---- nm d 585.5 ---- 594.5 nm Dominant Wavelength Spectrum Radiation Bandwidth ---- 15 ---- nm Viewing Angle 21/2 ---- 120 ---- deg Forward Voltage VF 1.70 ----- 2.30 V Reverse Current IR ---- ---- 10 A Condition IF=5mA VR =5V Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.05V Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Rev.2 Page: 3 of10 Prepared by:Denghuadong EVERLIGHT ELECTRONICS CO.,LTD. 12-21/Y2C-AL2N1LY/2C Bin Range Of Dom Wavelength Group A Bin Min Max D3 585.5 588.5 D4 588.5 591.5 D5 591.5 594.5 Unit Condition nm IF=5mA Bin Range Of Luminous Intensity Bin Min Max L2 14.5 18.0 M1 18.0 22.5 M2 22.5 28.5 N1 28.5 36.0 Unit Condition mcd IF=5mA Bin Range Of Forward Voltage Group L Bin Min Max 19 1.70 1.80 20 1.80 1.90 21 1.90 2.00 22 2.00 2.10 23 2.10 2.20 24 2.20 2.30 Unit Condition V IF=5 mA Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.05V Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Rev.2 Page: 4 of10 Prepared by:Denghuadong EVERLIGHT ELECTRONICS CO.,LTD. 12-21/Y2C-AL2N1LY/2C Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Rev.2 Page: 5 of10 Prepared by:Denghuadong EVERLIGHT ELECTRONICS CO.,LTD. 12-21/Y2C-AL2N1LY/2C Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank xxxxxx xxxxxx REF: Forward Voltage Rank RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Rev.2 Page: 6 of10 Prepared by:Denghuadong EVERLIGHT ELECTRONICS CO.,LTD. 12-21/Y2C-AL2N1LY/2C Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Desiccant Rev.2 Label Page: 7 of10 Prepared by:Denghuadong EVERLIGHT ELECTRONICS CO.,LTD. 12-21/Y2C-AL2N1LY/2C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 2605 Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100 15min 5 min L : -40 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100 5min 10 sec L : -10 5min 300 Cycles 22 PCS. 0/1 Temp. : 100 1000 Hrs. 22 PCS. 0/1 Temp. : -40 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 5 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85/ 85% RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Rev.2 Page: 8 of10 Prepared by:Denghuadong EVERLIGHT ELECTRONICS CO.,LTD. 12-21/Y2C-AL2N1LY/2C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Rev.2 Page: 9 of10 Prepared by:Denghuadong EVERLIGHT ELECTRONICS CO.,LTD. 12-21/Y2C-AL2N1LY/2C 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-121-Y04 Prepared date: 07-27-2005 Rev.2 Page: 10 of10 Prepared by:Denghuadong