IHL02 Series DC-DC Converter
Input
Output
Characteristic Minimum Typical maximum Units Notes & Conditions
Output Voltage 3.3 30 VDC See Models and Ratings table
Initial Set Accuracy ±5 % At full load
Minimum Load 10 % Minimum load required to meet specified regulation
Line Regulation ±1.2 %/1% Output changes by max of 1.2% for each 1% change in
input voltage
Load Regulation 12/10 % For IHL0205S3V3 and IHL0205S05/Other Models.
From 10% to full load, see application note
Cross Regulation ±5 % On dual output models, when one output is at 25% load
and other is varied from 10% load to full load
Ripple & Noise 150 mV pk-pk 20 MHz bandwidth. Measured using 10 µF electrolytic in
parallel with 0.1 µF ceramic capacitor
Short Circuit Protection Continuous
Maximum Capacitive Load See Models and Ratings table
Temperature Coefficient 0.03 %/ ˚C
Characteristic Minimum Typical maximum Units Notes & Conditions
Input Voltage Range
4.5 5.5
VDC
5 V nominal
10.8 13.2 12 V nominal
13.5 16.5 15 V nominal
21.6 26.4 24 V nominal
Input Reflected Ripple Current 20 mA pk-pk Through 12 µH inductor and 47 µF capacitor
Input Surge
9
VDC for 100 ms
5 V nominal
18 12 V nominal
20 15 V nominal
30 24 V nominal
xxx Series
www.xppower.com
1
High Isolation, 5200 V
250 VAC Working Voltage
Single and Dual Outputs
Bipolar Outputs for MOSFET and IGBT Drives
SIP7 Package
-40 °C to +95 °C Operation
Full Load at 65 °C Ambient
MTBF 2.5 MHrs
3 Year Warranty
Dimensions:
IHL02:
0.77 x 0.28 x 0.39” (19.5 x 7.2 x 10.0 mm)
2 Watts
Mechanical Details
Printed
Face
0.28
(7.2)
0.39
(10.0)
0.02
(0.5)
0.02
(0.5)
0.02
(0.5)
0.01
(0.25)
0.08
(2.0)
0.12
(3.0)
0.37
(9.5)
0.08
(2.13)
0.08
(2.13)
0.10 (2.54)
0.60 (15.24)
0.76 (19.5) 0.28
(7.2)
1. All dimensions are in inches (mm)
2. Weight: 0.006 lbs (2.7 g) approx.
3. Pin diameter: 0.02±0.002 (0.5±0.05)
4. Pin pitchand length tolerance: ±0.014 (±0.35)
5. Case tolerance: ±0.02 (±0.5)
Notes
Pin Connections
Pin Single Dual
1 +Vin +Vin
2 -Vin -Vin
5 -Vout -Vout
6 No Pin Common
7 +Vout +Vout
IHL02 Series
www.xppower.com 2
DC-DC Converter
Models & Ratings
Notes
Input currents measured at nominal input voltage.
General
Characteristic Minimum Typical maximum Units Notes & Conditions
Efficiency 80 % See Models and Ratings table
Isolation: Input to Output 5200 VDC
Isolation Working Voltage 250 VAC
Isolation Resistance 109Ω
Isolation Capacitance 7 pF
Switching Frequency 50 100 kHz
Power Density 23.7 W/in3
Mean Time Between Failure 3.3 MHrs MIL-HDBK-217F, +25 °C GB
Weight 0.006 (2.7) lb (g)
Input Voltage Output Voltage Output Current Input current Maximum Capacitive
Load Efficiency Model Number
No Load Full Load
4.5-5.5V
3V3 500 mA 40 mA 435 mA 1000 µF 76% IHL0205S3V3
5 V 400 mA 40 mA 505 mA 470 µF 79% IHL0205S05
9 V 222 mA 40 mA 480 mA 470 µF 83% IHL0205S09
12 V 167 mA 40 mA 475 mA 220 µF 84% IHL0205S12
15 V 133 mA 40 mA 470 mA 220 µF 85% IHL0205S15
±5 V ±200 mA 40 mA 505 mA ±220 µF 79% IHL0205D05
±9 V ±111 mA 40 mA 490 mA ±220 µF 82% IHL0205D09
±12 V ±83.3 mA 40 mA 480 mA ±100 µF 83% IHL0205D12
±15 V ±66.7 mA 40 mA 475 mA ±100 µF 84% IHL0205D15
+15/-9 V +66.7/-111 mA 40 mA 480 mA +100/-220 µF 83% IHL0205D1509
10.8-13.2V
3V3 500 mA 30 mA 185 mA 1000 µF 74% IHL0212S3V3
5 V 400 mA 30 mA 210 mA 470 µF 79% IHL0212S05
9 V 222 mA 30 mA 205 mA 470 µF 82% IHL0212S09
12 V 167 mA 30 mA 205 mA 220 µF 82% IHL0212S12
15 V 133 mA 30 mA 200 mA 220 µF 83% IHL0212S15
±5 V ±200 mA 30 mA 210 mA ±220 µF 79% IHL0212D05
±9 V ±111 mA 30 mA 205 mA ±220 µF 81% IHL0212D09
±12 V ±83.3 mA 30 mA 200 mA ±100 µF 83% IHL0212D12
±15 V ±66.7 mA 30 mA 200 mA ±100 µF 83% IHL0212D15
+15/-9V +66.7/-111 mA 30 mA 210 mA +100/-220 µF 80% IHL0212D1509
13.5-16.5V
3V3 500 mA 25 mA 150 mA 1000 µF 74% IHL0215S3V3
5 V 400 mA 25 mA 170 mA 470 µF 78% IHL0215S05
9 V 222 mA 25 mA 165 mA 470 µF 81% IHL0215S09
12 V 167 mA 25 mA 165 mA 220 µF 82% IHL0215S12
15 V 133 mA 25 mA 160 mA 220 µF 83% IHL0215S15
±5 V ±200 mA 25 mA 170 mA ±220 µF 79% IHL0215D05
±9 V ±111 mA 25 mA 165 mA ±220 µF 81% IHL0215D09
±12 V ±83.3 mA 25 mA 160 mA ±100 µF 83% IHL0215D12
±15 V ±66.7 mA 25 mA 165 mA ±100 µF 82% IHL0215D15
+15/-9V +66.7/-111 mA 25 mA 165 mA +100/-220 µF 81% IHL0215D1509
21.6-26.4V
3V3 500 mA 20 mA 95 mA 1000 µF 73% IHL0224S3V3
5 V 400 mA 20 mA 105 mA 470 µF 78% IHL0224S05
9 V 222 mA 20 mA 105 mA 470 µF 81% IHL0224S09
12 V 167 mA 20 mA 105 mA 220 µF 81% IHL0224S12
15 V 133 mA 20 mA 105 mA 220 µF 81% IHL0224S15
±5 V ±200 mA 20 mA 105 mA ±220 µF 79% IHL0224D05
±9 V ±111 mA 20 mA 105 mA ±220 µF 80% IHL0224D09
±12 V ±83.3 mA 20 mA 105 mA ±100 µF 81% IHL0224D12
±15 V ±66.7 mA 20 mA 100 mA ±100 µF 82% IHL0224D15
+15/-9V +66.7/-111 mA 20 mA 105 mA +100/-220 µF 80% IHL0224D1509
3
IHL02 Series
www.xppower.com
DC-DC Converter
3
Mechanical Details
EMC: Immunity
Phenomenon Standard Test Level Criteria Notes & Conditions
ESD Immunity EN61000-4-2 ±6/±8 kV A Contact/Air Discharge
Radiated Immunity EN61000-4-3 10 Vrms A
EFT/Burst EN61000-4-4 2 kV A External components required,
see application notes
Conducted Immunity EN61000-4-6 10 V rms A
magnetic Fields EN61000-4-8 1 A/m A
Printed
Face
0.28
(7.2)
0.39
(10.0)
0.02
(0.5)
0.02
(0.5)
0.02
(0.5)
0.01
(0.25)
0.08
(2.0)
0.12
(3.0)
0.37
(9.5)
0.08
(2.13)
0.08
(2.13)
0.10 (2.54)
0.60 (15.24)
0.76 (19.5) 0.28
(7.2)
1. All dimensions are in inches (mm)
2. Weight: 0.006 lbs (2.7 g) approx.
3. Pin diameter: 0.02±0.002 (0.5±0.05)
4. Pin pitch and length tolerance: ±0.014 (±0.35)
5. Case tolerance: ±0.02 (±0.5)
Notes
Pin Connections
Pin Single Dual
1 +Vin +Vin
2 -Vin -Vin
5 -Vout -Vout
6 No Pin Common
7 +Vout +Vout
EMC: Emissions
Phenomenon Standard Test Level Notes & Conditions
Conducted EN55032 Class B See Application Note
Radiated EN55032 Class B
Environmental
Characteristic Minimum Typical maximum Units Notes & Conditions
Operating Temperature -40 +95 °C Derate Linearly from 100% at 65 °C to no load at 95 °C
Storage Temperature -40 +125 °C
Case Temperature +100 °C
Humidity 2.5 95 %RH Non-condensing
Cooling Natural convection
IHL02 Series
www.xppower.com
DC-DC Converter
23 Aug 16
Input components C1 and D1 are used to help meet EFT and surge test requirements for the module.
Application Note
C1 D1
IHL0205XXXX 330 µF/50 V SMDJ9.0 A
IHL0212XXXX 330 µF/50 V SMDJ13 A
IHL0215XXXX 330 µF/50 V SMDJ18 A
IHL0224XXXX 1000 µF/35 V SMDJ24 A
High limit
T
ypical Load Line
Low Limit
IHL02
D1
Regulation
EFT Filter
Input filter components (C1,C2, C3 and L) are used to help meet conducted emissions requirements for the module. These components should be
mounted as close as possible to the module, and all leads should be minimised to decrease radiated noise.
C1 L C2 C3
IHL0205XXXX 1206, 4.7 µF/ 16 V 6.8 µH
IHL0212XXXX 1206, 22 µF/ 25 V 6.8 µH
IHL0215XXXX 1206, 22 µF/ 25 V 6.8 µH
IHL0224XXXX 1210, 10 µF/ 35 V 10 µH 1210, 10 µF/ 35 V 1210, 10 µF/ 35 V
IHL02
C3
L
EMI Filter