PL135-67 Low Power, 1.62V to 3.63V, 10M Hz to 40M Hz, 1:6 Oscillat or Fanout Buffer FEATURES DESCRIPTION Advanced Oscillator Design for Wide Frequency Coverage 6 LVCMOS Outputs with 2 Output Enable Pins 8mA Output Drive Strength Input/Output Frequency: o Fundamental Crystal: 10MHz to 40MHz Very Low Jitter and Phase Noise Low Current Consumption Single 1.62V to 3.63V Power Supply Available in QFN-16L and TSSOP-16L GREEN/RoHS Compliant Packages The PL135-67 is an advanced oscillator fanout buffer design for high performance, low-power, small formfactor applications. The PL135-67 accepts a fundamental input crystal of 10MHz to 40MHz and produces six outputs of the same frequency, two with their own Output Enable functions. Offered in a small 3 x 3mm QFN or TSSOP package, the PL135-67 offers the best phase noise and jitter performance and lowest power consumption of any comparable IC. XIN XOUT VDD 11 10 9 14 OE0 16 1 6 2 3 4 5 CLK3 CLK2 GND CLK1 OE1 15 CLK0 VDD 8 7 VDD CLK5 12 13 GND CLK4 GND PACKAGE PIN CONFIGURATION QFN XIN 1 16 XOUT GND 2 15 VDD CLK4 3 14 CLK3 CLK5 4 13 CLK2 VDD 5 12 GND OE0 6 11 CLK1 CLK0 7 10 OE1 VDD 8 9 GND TSSOP BLOCK DIAGRAM CLK0 OE0 CLK1 OE1 XIN XOUT XTAL OSC CLK2 CLK3 CLK4 CLK5 Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1(408) 944 -0800 * fax +1(408) 474-1000 * www.micrel.com Rev 02/14/11 Page 1 PL135-67 Low Power, 1.62V to 3.63V, 10M Hz to 40M Hz, 1:6 Oscillat or Fanout Buffer PACKAGE PIN ASSIGNMENT Name Package Pin # Type Description QFN-16L (T)SSOP-16L CLK0 1 7 O Output clock VDD 2, 9, 15 5, 8, 15 P V DD connection GND 3, 6, 12 2, 9, 12 P GND connection OE1 4 6 I* Output enable (OE) input for CLK1. Internal pull-up. Pull low to tri-state CLK1. CLK1 5 11 O Output clock CLK2 7 13 O Output clock CLK3 8 14 O Output clock XOUT 10 16 O Crystal output. Do not connect when using reference clock. XIN 11 1 I Crystal input CLK4 13 3 O Output clock CLK5 14 4 O Output clock OE0 14 4 I* Output enable (OE) input for CLK0. Internal pull-up. Pull low to tri-state CLK0. * Note: These pins include an internal 60k pull up. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1(408) 944 -0800 * fax +1(408) 474-1000 * www.micrel.com Rev 02/14/11 Page 2 PL135-67 Low Power, 1.62V to 3.63V, 10M Hz to 40M Hz, 1:6 Oscillat or Fanout Buffer LAYOUT RECOMMENDATIONS The following guidelines are to assist you with a performance optimized PCB design: Signal Integrity and Termination Considerations Decoupling and Power Supply Considerations - Keep traces short! - Place decoupling capacitors as close as possible to the V DD pin(s) to limit noise from the power supply - Trace = Inductor. With a capacitive load this equals ringing! - Long trace = Transmission Line. Without proper termination this will cause reflections (looks like ringing). - Design long traces as "striplines" or "microstrips" with defined impedance. - Match trace at one side to avoid reflections bouncing back and forth. - Addition of a ferrite bead in series with V DD can help prevent noise from other board sources - Value of decoupling capacitor is frequency dependant. Typical value to use is 0.1F. Crystal Tuning Circuit Series and parallel capacitors used to fine tune the crystal load to the circuit load. Typical CMOS termination Place Series Resistor as close as possible to CMOS output CMOS Output Buffer (Typical buffer impedance 20) - Multiple V DD pins should be decoupled separately for best performance. Crystal To CMOS Input 50 line Cst Series Resistor Use value to match output buffer impedance to 50 trace. Typical value 30 XIN XOUT 1 8 Cpt Cpt CST - Series Capacitor, used to lower circuit load to match crystal load. Raises frequency offset. This can be eliminated by using a crystal with a Cload of equal or greater value than the oscillator. CPT - Parallel Capacitors, Used to raise the circuit load to match the crystal load. Lowers frequency offset. ELECTRICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS PARAMETERS SYMBOL MIN. MAX. UNITS V DD -0.5 4.6 V Input Voltage Range VI -0.5 V DD+0.5 V Output Voltage Range VO -0.5 V DD+0.5 V Storage Temperature TS -65 150 C -40 85 C Supply Voltage Range Ambient Operating Temperature* Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. *Operating temperature is guaranteed by design. Parts are tested to commercial grade only. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1(408) 944 -0800 * fax +1(408) 474-1000 * www.micrel.com Rev 02/14/11 Page 3 PL135-67 Low Power, 1.62V to 3.63V, 10M Hz to 40M Hz, 1:6 Oscillat or Fanout Buffer AC SPECIFICATIONS PARAMETERS CONDITIONS MIN. TYP. 10 MAX. UNITS 40 MHz Crystal Input Frequency Fundamental Crystal Settling Time At power-up (V DD > 1.62V) 2 ms Output Enable Time OE Function; Ta=25 C, 10pF Load 10 ns V DD Sensitivity Frequency vs. V DD, 10% 2 ppm Output Rise Time 15pF Load, 10/90% V DD, 3.3V 2 4 ns Output Fall Time 15pF Load, 90/10% V DD, 3.3V 2 4 ns Output to Output Skew Under all conditions 1 ns Duty Cycle Under all conditions -2 45 50 55 % MIN TYP MAX UNITS DC SPECIFICATIONS PARAMETERS SYMBOL Supply Current, Dynamic I DD CONDITIONS V DD = 3.3V, 25MHz, No Load 7.1 mA V DD = 2.5V, 25MHz, No Load 4.8 mA V DD = 1.8V, 25MHz, No Load 3.4 mA Operating Voltage V DD 1.62 Output Low Voltage V OL I OL = +4mA, 3.3V Output High Voltage V OH I OH = -4mA, 3.3V Output Current I OSD V OL = 0.4V, V OH = 2.4V 3.63 V 0.4 V 2.4 V 8 mA CRYSTAL SPECIFICATIONS PARAMETERS Fundamental Crystal Resonator Frequency Crystal Loading Rating SYMBOL MIN. F XIN 10 CL (x ta l) Operating Drive Level Metal Can Crystal Small SMD Crystal TYP. ESR Max Shunt Capacitance ESR Max UNITS 40 MHz 15 0.1 Shunt Capacitance MAX. pF 2 mW C0 5.5 pF ESR 40 C0 2.5 pF ESR 60 Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1(408) 944 -0800 * fax +1(408) 474-1000 * www.micrel.com Rev 02/14/11 Page 4 PL135-67 Low Power, 1.62V to 3.63V, 10M Hz to 40M Hz, 1:6 Oscillat or Fanout Buffer PACKAGE DRAWINGS (GREEN PACKAGE COM PLIANT) QFN 16L A e L D D1 E1 b SEATING PLANE A1 Pin1 Dot A3 A A1 A3 b D E D1 E1 L e Dimension in MM Min. Max. 0.07 0.8 0.05 0.05 0.20 0.18 0.30 3.00 BSC 3.00 BSC -1.70 -1.70 0.30 0.50 0.50 BSC E Symbol TSSOP 16L Symbol A A1 b C D E H L e Dimension in MM Min. Max. 1.20 0.05 0.15 0.19 0.30 0.09 0.20 4.90 5.10 4.30 4.50 6.20 6.60 0.45 0.75 0.635 BSC E H D A A1 C e B Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1(408) 944 -0800 * fax +1(408) 474-1000 * www.micrel.com L Rev 02/14/11 Page 5 PL135-67 Low Power, 1.62V to 3.63V, 10M Hz to 40M Hz, 1:6 Oscillat or Fanout Buffer ORDERING INFORM ATION (GREEN PACKAGE COM PLIANT) For part ordering, please contact our Sales Department: 2180 Fortune Drive, San Jose, CA 95131, USA Tel: (408) 944-0800 Fax: (408) 474-1000 PART NUMBER The order number for this device is a combination of the following: Part number, Package type and Operating temperature range PL135-67 X X - X Part Number Shipping Option None=Tubes R=Tape and Reel Package Type O = TSSOP-16L Q = QFN-16L Temperature Range C=Commercial (0C to 70C) Part Number/Order Number Marking PL135-67OC P135-67 OC LLLLL P135 67 LLL PL135-67OC-R PL135-67QC-R Package Option 16-Pin TSSOP (Tube) 16-Pin TSSOP (Tape and Reel) 16-Pin QFN (Tape and Reel) *Note: LLL designates lot number Micrel Inc., reserves the right to make changes in its products or specifications, or both at any time without notice. The information furnished by Micrel is believed to be accurate and reliable. However, Micrel makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: Micrel's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Micrel Inc. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1(408) 944 -0800 * fax +1(408) 474-1000 * www.micrel.com Rev 02/14/11 Page 6