DATASHEET ICS570 MULTIPLIER AND ZERO DELAY BUFFER Description Features The ICS570 is a high-performance Zero Delay Buffer (ZDB) which integrates IDT's proprietary analog/digital Phase Locked Loop (PLL) techniques. The A version is recommended for 5 V designs and the B version for 3.3 V designs. The chip is part of IDT's ClockBlocksTM family, and was designed as a performance upgrade to meet today's higher speed and lower voltage requirements. The zero delay feature means that the rising edge of the input clock aligns with the rising edges of both output clocks, giving the appearance of no delay through the device. There are two outputs on the chip, one being a low-skew divide by two of the other output. The device incorporates an all-chip power down/tri-state mode that stops the internal PLL and puts both outputs into a high impedance state. * * * * * * * * * * * * The ICS570 is ideal for synchronizing outputs in a large variety of systems, from personal computers to data communications to graphics/video. By allowing off-chip feedback paths, the device can eliminate the delay through other devices. * * * * The ICS570 A and B versions were designed to improve input to output jitter from the original ICS570M version, and are recommended for all new designs. 8-pin SOIC package Available in Pb (lead) free package Pin-for-pin replacement and upgrade to ICS570M Functional equivalent to AV9170 (not a pin-for-pin replacement) Low input to output skew of 300 ps max (>60 MHz outputs) Ability to choose between 14 different multipliers from 0.5x to 32x Output clock frequency up to 170 MHz at 3.3 V Can recover degraded input clock duty cycle Output clock duty cycle of 45/55 Power Down and Tri-State Mode Passes spread spectrum clock modulation Full CMOS clock swings with 25 mA drive capability at TTL levels Advanced, low power CMOS process ICS570B has an operating voltage of 3.3 V (5%) ICS570A has an operating voltage of 5.0 V (5%) Industrial temperature version available Block Diagram IC L K S 1 :0 F B IN d ivid e by N Phase D e te c to r, C h a rg e Pum p, and Loop F ilte r VCO C LK /2 C LK2 E xte rn a l fe e d b a ck ca n co m e fro m C L K o r C L K /2 (se e ta b le o n p a g e 2 ) IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER 1 ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Pin Assignment S1 1 8 CLK/2 VDD 2 7 CLK GND 3 6 S0 ICLK 4 5 FBIN 8 pin (150 mil) SOIC Clock Multiplier Decoding Table (Multiplies Input clock by amount shown) S1 S0 FBIN from CLK CLK #1 0 0 0 M M M 1 1 1 #6 0 M 1 0 M 1 0 M 1 CLK/2 FBIN from CLK/2 CLK ICS570B (3.3 V) ICS570A (5.0 V) CLK/2 ICLK Input Range FB from CLK/2* ICLK Input Range FB from CLK/2* pin #7 pin #8 pin #7 pin #8 Power Down and Tri-State x3 x1.5 x6 x3 x4 x2 x8 x4 x8 x4 x16 x8 x6 x3 x12 x6 x10 x5 x20 x10 x1 /2 x2 x1 x16 x8 x32 x16 x2 x1 x4 x2 0 = connect directly to ground 3.75 to 28 2.75 to 19 2.5 to 9.5 2.5 to 12.5 2.5 to 7.5 11 to 85 1.5 to 5 5.5 to 37.5 2.5 to 25 2.5 to 19 2.5 to 9.5 2.5 to 12.5 2.5 to 7.5 5 to 75 1.5 to 5 2.5 to 37.5 M = leave unconnected (self-biases to VDD/2) 1 = connect directly to VDD *Input range with CLK feedback is double that for CLK/2 IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER 2 ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Pin Descriptions Pin Number Pin Name Pin Type 1 2 3 4 5 6 7 8 S1 VDD GND ICLK FBIN S0 CLK CLK/2 Input Power Power Input Input Input Output Output Pin Description Select 1 for output clock. Connect to GND, VDD, or float per decoding Connect to +3.3 V (ICS570B). Connect to +5.0 V (ICS570A). Connect to ground. Reference clock input. Feedback clock input. Select 0 for output clock. Connect to GND, VDD, or float per decoding Clock output per table above. Clock output per table above. Low skew divide by two of pin 7 clock. External Components The ICS570 requires a 0.01F decoupling capacitor to be connected between VDD and GND. It must be connected close to the part to minimize lead inductance. No external power supply filtering is required for this device. A 33 series terminating resistor can be used next to each output pin. Recommended Circuit S1 CLK VDD CLK/2 ICLK GND S0 Input CLK FBIN CLK/2 x2 Mode (S1, S0 = 1, 0) CLK/2 Feedback ICLK CLK CLK/2 x2 Mode (S1, S0 = 1, 1) CLK Feedback IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER 3 ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Using CLK as the feedback will always result in synchronized rising edges between ICLK and CLK. However, the CLK/2 could be a falling edge compared with ICLK. IDT recommends using CLK/2 feedback whenever possible. This will synchronize the rising edges of all three clocks. Clock Period Jitter Tables (ICS570A) All jitter values are considered typical measured at 25 C with 27 termination resistor and 15 pF loads on both CLK and CLK/2. The feedback is from CLK/2 to FBIN. Note that if an output is unused, it should be left unconnected to improve output jitter on the active output clocks. Absolute and One Sigma Jitter (ps) S S CLKIN Multiplier CLK = 50M P to P 1 sigma Multiplier CLK/2 = 25M P to P 1 sigma 0 0 M M M 1 1 1 M 1 0 M 1 0 M 1 8.333 6.25 3.125 4.167 2.5 25 1.5625 12.5 6x 8x 16x 12x 20x 2x 32x 4x 115 115 120 120 120 120 120 120 80 80 80 90 80 70 80 80 3x 4x 8x 6x 10x 1x 16x 2x 65 60 55 60 60 55 50 55 20 20 20 20 20 20 20 20 Absolute and One Sigma Jitter (ps) S S CLKIN Multiplier CLK = 100M P to P 1 sigma Multiplier CLK/2 = 50M P to P 1 sigma 0 0 M M M 1 1 1 M 1 0 M 1 0 M 1 16.667 12.5 6.25 8.333 5 50 3.125 25 6x 8x 16x 12x 20x 2x 32x 4x 135 140 140 140 135 120 135 130 100 100 110 110 100 90 100 90 3x 4x 8x 6x 10x 1x 16x 2x 55 50 55 55 50 50 55 65 20 20 20 20 20 20 20 20 Absolute and One Sigma Jitter (ps) S S CLKIN Multiplier CLK = 150M P to P 1 sigma Multiplier CLK/2 = 75M P to P 1 sigma 0 0 M M M M 1 0 M 1 25 18.375 9.375 12.5 7.5 6x 8x 16x 12x 20x 160 165 170 160 160 120 120 120 120 120 3x 4x 8x 6x 10x 55 55 50 55 55 20 20 20 20 20 IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER 4 ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER 1 1 1 0 M 1 75 4.6875 37.5 2x 32x 4x ZDB AND MULTIPLIER 155 165 160 110 120 110 1x 16x 2x 55 55 50 20 20 20 Clock Period Jitter Tables (ICS570B) All jitter values are considered typical measured at 25 C with 27 termination resistor and 15 pF loads on both CLK and CLK/2. The feedback is from CLK/2 to FBIN. Note that if an output is unused, it should be left unconnected to improve output jitter on the active output clocks. Absolute and One Sigma Jitter (ps) S S CLKIN Multiplier CLK = 50M P to P 1 sigma Multiplier CLK/2 = 25M P to P 1 sigma 0 0 M M M 1 1 1 M 1 0 M 1 0 M 1 8.333 6.25 3.125 4.167 2.5 25 1.5625 12.5 6x 8x 16x 12x 20x 2x 32x 4x 110 125 130 120 115 130 120 120 80 90 90 90 90 50 90 60 3x 4x 8x 6x 10x 1x 16x 2x 55 50 55 55 55 55 55 55 20 20 20 20 20 20 20 20 Absolute and One Sigma Jitter (ps) S S CLKIN Multiplier CLK = 100M P to P 1 sigma Multiplier CLK/2 = 50M P to P 1 sigma 0 0 M M M 1 1 1 M 1 0 M 1 0 M 1 16.667 12.5 6.25 8.333 5 50 3.125 25 6x 8x 16x 12x 20x 2x 32x 4x 100 100 110 100 105 90 95 105 70 70 80 70 70 60 70 70 3x 4x 8x 6x 10x 1x 16x 2x 45 45 45 45 40 40 45 60 20 20 20 20 20 20 20 20 Absolute and One Sigma Jitter (ps) S S CLKIN 0 0 M M M 1 0 M 25 18.375 9.375 12.5 CLK = 150M Multiplier P to P 6x 8x 16x 12x 115 120 130 130 IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER 1 sigma 70 80 90 90 5 CLK/2 = 75M Multiplier P to P 3x 4x 8x 6x 1 sigma 50 50 50 45 20 20 20 20 ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER M 1 1 1 1 0 M 1 7.5 75 4.6875 37.5 20x 2x 32x 4x ZDB AND MULTIPLIER 130 115 130 110 90 90 90 70 10x 1x 16x 2x 45 45 50 60 20 20 20 20 Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS570. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature, Commercial version 0 to +70 C Ambient Operating Temperature, Industrial version -40 to +85 C Storage Temperature -65 to +150 C Junction Temperature 125 C Soldering Temperature 260 C Recommended Operation Conditions Parameter Min. Ambient Operating Temperature, Commercial version Ambient Operating Temperature, Industrial version Power Supply Voltage (measured in respect to GND) IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER 6 Max. Units 0 70 C -40 +85 C +3.45 V +3.15 Typ. +3.3 ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V 5%, Ambient Temperature -40 to +85 C Parameter Operating Voltage Operating Current Symbol VDD IDD Conditions Min. Typ. Max. Units V ICS570B, ICS570M 3.15 3.45 ICS570A, ICS570M 4.75 5.25 ICS570B, ICS570M VDD=3.3 V, 50M input, S1:0 = 11 16 mA ICS570A, ICS570M VDD=5.0 V, 50M input, S1:0 = 11 25 mA Input High Voltage VIH ICLK, FBIN Input Low Voltage VIL ICLK, FBIN Input High Voltage VIH S0, S1 Input Low Voltage (mid-level) VIM S0, S1 Input Low Voltage VIL S0, S1 Output High Voltage (CMOS High) VOH IOH = -4 mA VDD-0.4 V Output High Voltage VOH IOH = -12 mA 2.4 V Output Low Voltage VOL IOL = 12mA Short Circuit Current IOS Each output Input Capacitance CIN S0, S1 IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER 2 V 0.8 VDD-0.5 V VDD/2 V 0.5 7 V 0.4 V V 100 mA 5 pF ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V 5%, Ambient Temperature -40 to +85 C Parameter Symbol Conditions Input Frequency, ICLK FBIN from CLK/2 Output Clock Frequency CLK Output to Output Skew ICS570B, ICS570M Output to Output Skew VDD=5 V, ICS570A Input to Output Jitter 40 - 150 MHz Min. Typ. Max. Units See table on page 2 10 ICS570M 170 MHz 100 175 ps 100 200 ps 100-250 ps 600 ps ICLK to FBIN, CLK>30MHz, Note 1 -300 300 ps ICLK to FBIN, CLK<10MHz, Note 1 -600 600 ps ICLK to FBIN CLK>30MHz, Note 1 -1 1 ns Input Skew, ICS570A ICLK to FBIN, CLK<10MHz, Note 1 -1.5 1.5 ns Output Clock Rise Time 0.8 to 2.0V, Note 2 0.75 ns Output Clock Fall Time 2.0 to 0.8V, Note 2 0.75 ns Output Clock Duty Cycle at VDD/2 Input Skew, ICS570B, ICS570M 45 49 - 51 55 % Note 1: Assumes clocks with same rise time, measured from rising edges at VDD/2 Note 2: Measured with 27 terminating resistor and 15 pF loads Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER Symbol Conditions Min. Typ. Max. Units JA Still air 150 C/W JA 1 m/s air flow 140 C/W JA 3 m/s air flow 120 C/W 40 C/W JC 8 ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body) Package dimensions are kept current with JEDEC Publication No. 95 8 Millimeters Symbol E H INDEX AREA 1 2 D A h x 45 Min A A1 B C D E e H h L a Max 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0 8 A1 Inches Min Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .1890 .1968 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0 8 C -Ce B SEATING PLANE L .10 (.004) IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER C 9 ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature 570A 570AT 570AI 570AIT 570AILF 570AILFT 570ALF 570ALFT 570B 570BT 570BLF 570BLFT 570BI 570BIT 570BILF 570BILFT 570M 570MT 570MLF 570MLFT 570MI 570MIT ICS570A ICS570A ICS570AI ICS570AI 570AILF 570AILF 570ALF 570ALF ICS570B ICS570B ICS570BL ICS570BL ICS570BI ICS570BI 570BILF 570BILF ICS570M ICS570M 570MLF 570MLF ICS570MI ICS570MI Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel Tubes Tape and Reel 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 0 to +70 C 0 to +70 C -40 to 85 C -40 to 85 C -40 to 85 C -40 to 85 C 0 to +70 C 0 to +70 C 0 to +70 C 0 to +70 C 0 to +70 C 0 to +70 C -40 to 85 C -40 to 85 C -40 to 85 C -40 to 85 C 0 to +70 C 0 to +70 C 0 to +70 C 0 to +70 C -40 to 85 C -40 to 85 C Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDTTM / ICSTM MULTIPLIER AND ZERO DELAY BUFFER 10 ICS570 REV K 073007 ICS570 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 408-284-4522 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com (c) 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA