1 - 0-1 AAC
5 - 0-5 AAC
15 - 0-15 AAC
25 - 0-25 AAC
Above 30 AAC must use 5 amp CT
Data Stream
13
B
3500 Scarlet Oak Blvd. St. Louis MO USA 63122 V: 636-343-8518 F: 636-343-5119
Web: http://www.crmagnetics.com E-mail: sales@crmagnetics.com
The Professional
Energy Monitoring
Company
ISO 9001:2008 Quality Management System
M
NTI
CRD5110
Single Element - .26” (6.5) Window
150 to 300 VAC
1 to 25 AAC Input Range
CRD5150
Two Element - .26” (6.5) Window
150 to 300 VAC
1 to 25 AAC Input Range
CRD5170
Three Element - .26” (6.5) Window
150 to 300 VAC
1 to 25 AAC Input Range
Sensing
Voltage, True RMS
Current, True RMS
Active Power, bi-directional
Active Energy, bi-directional
Reactive Power, bi-directional
Reactive Energy, bi-directional
Power Factor
Frequency
Applications
Sub-Metering
Motor Loads
Uninterruptible Power Systems
Remote Monitoring
Load Shedding
Energy Management
Features
35mm DIN Rail or Panel Mount
Red LED - Flashes when Power is Connected
Red & Green LED Flash during Communication
24 VDC powered
Use with external current transformers
Highest precision available
Connection diagram printed on case
Regulatory Agencies
Data Stream RS485 Digital Transducer
DIN RAIL / PANEL MOUNT
150 - 0-150 VAC
300 - 0-300 VAC
Available up to and including 600 VAC
The CRD5100 Series Data Stream Digital Transducers are designed for
complete monitoring of electrical power systems. The digital technolo-
gy is used to measure voltage, current, power frequency and energy in
single and three phase designs. The data is streamed over an RS485
IEEE bus which enables multiple transducers to communicate thru a sin-
gle master connection. These advanced sensors are ideal for entire
plant or zone monitoring. Also, the communication alagorithm can be
pre-ordered with ASCII based control or modified MODBUS based
control.
Note: Add an M at
the end for MODBUS
CRD5110-150-5-M
PART NUMBERS
CRD5110 - - 1 Element, AC Multifunction RS485 Digital Transducer
CRD5150 - - 3 Phase, 3-Wire AC Multifunction RS485 Digital Transducer
CRD5170 - - 3 Phase, 4-Wire AC Multifunction RS485 Digital Transducer
14
Data Stream
B
3500 Scarlet Oak Blvd. St. Louis MO USA 63122 V: 636-343-8518 F: 636-343-5119
Web: http://www.crmagnetics.com E-mail: sales@crmagnetics.com
The Professional
Energy Monitoring
Company
ISO 9001:2008 Quality Management System
M
NTI
RS485 Digital Transducer
CRD5110 Single Element, 2-Wire
LOAD
1
2
3
4
5
6
7
9
8
LN
LINE
-
-
+
+
SUPPLY
485
LOAD
8
7
9
5
6
1
4
2
3
L2L1N
LINE
-
-
+
+
SUPPLY
485
NL3
L1 L2
1
3
4
2
LOAD
9
8
7
6
5
LOAD
8
7
9
5
6
1
4
2
3
L3L1L2
LINE
-
-
+
+
SUPPLY
485
CRD5150 Dual Element, 3-Wire
CRD5150 Dual Element, 3-Wire CRD5170 3 Element, 4-Wire
ASCII Simplified Programming Commands
A simplified data structure is used with only 6 commands required for full control of
the transducer. Commands are : Read Transducer Name, Read Configuration, Set
Configuration, Read Measurements, Read Energy Totalizer and Clear Energy
Totalizer. For illustration, the following commands are used to read data from a
CRD5170 3 Phase, 4 Wire Transducer with a device address of 00.
Command Transducer to Read Data: #00A<cr>
Transducers Response: >+[% FS VoltageL1-N]+[% FS CurrentL1]+[% FS
VoltageL2-N]+[% FS CurrentL2]+[% FS VoltageL3-N]+[% FS CurrentL3,][+/- % FS
Power][+/-% FS VARS][+/-Power Factor][Frequency]<cr>
Command Transducer to Read Energy Totalizer: #00W<cr>
Transducer Responds: 01[+/-KWHr]
{\[+/-KVHr][check sum]<cr>
Note: This is for illustration purposes only, See Applications Guides (Section I
for complete instructions.
SPECIFICATIONS
Connection Diagram
NL1 L2
LINE
LOAD
LINE
LOAD
NL1 L2 L3
NL1
LINE
LOAD
LINE
L2 L1 L3
LOAD
SUPPLY
485
DATA +
DATA-
GND
+5VDC
COM
RS232
CRD485-232
SUPPLY
5
6
7
9
8
+-
DATA STREAM
TRANSDUCER
TX
RX
GND
DB 9, FEMALE
1
2
3
4
CRD485-232
RS485 to RS232 Converter Accessory
Connect PC to RS485 Bus
Basic Accuracy: .......................0.5%
Calibration: ..............................True RMS Sensing
Thermal Drift: ..........................500 PPM/°C
Operating Temperature1: ..........0°C to +60°C
Installation Category: ..............CAT II
Vibration Tested To: .................IEC 60068-2-6,1995
Pollution Degree: ....................2
Insulation Voltage: ..................2500 VDC
Altitude: ..................................2000 meter max
Frequency Range: .................20 Hz - 5 KHz
MTBF: ....................................Greater than 100K hours
Cleaning: ................................Water-dampened cloth
Supply Voltage2: ......................24 VDC ±10%
1) RH 5% to 95%, non-condensing 2) 0.4% max. ripple Vpp
3) Factory default settings: address 01, baud rate 9600, no parity,
Torque Specifications: ....................3.0 inch lbs (0.4Nm)
Response Time: .......................250 ms. max. 0-90% FS
Relative Humidity: .............5% to 95%, Non-Condensing
Output Resolution: ..................................................16 bit
Transducer fanout on common bus: ...................64 max.
Baud Rate3: ...............1200, 2400, 4800, 9600,19.2K .bps
A/D Conversion Type: ..................4th order Delta Sigma
Device Address3: ............................................00 to FF
Data Format: .... .....................................................ASCII
Supply Current:..................Typical 30mA Max 30mA
Weight:.. ..............................................................0.5 lbs.
no flow control, 1 stop bit
OUTLINE DRAWING
[3.3]
.13
OPTIONAL
MOUNTING
RED INDICATIOR LED
GREEN INDICATOR LED
DIN RAIL
MOUNTING
CLIP
[26.6]
1.05
[73.1]
2.88
[83.3]
3.28
[31.0]
1.22
[78.7]
3.10
MAX
[6.6]
.26
[5.6]
.22
TYP
[88.7]
3.49
[64]
2.52
[76.7]
3.02
[25]
.98
[28.3]
1.12
[36.6]
1.44
[35.0]
1.38
[13.5]
.53
[31.0]
1.22
[19.8]
.78
[19.8]
.78