EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 1 of 9
Device No. :DSE-171-065 Prepared date: 17-Jan-2005 Prepared by: Jessica Chang
Technical Data Sheet
0805 Package Chip LED (1.1mm Height)
17-21UYOC/S530-XX/TR8
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
Descriptions
․The 17-21 SMD Taping is much smaller
than lead frame type components, thus
enable smaller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Chip
Material Emitted Color
Lens Color
AlGaInP Super Yellow Orange Water Clear
EVERLIGHT ELECTRONICS CO.,LTD.
17-21UYOC/S530-XX/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 2 of 9
Device No. :DSE-171-065 Prepared date: 17-Jan-2005 Prepared by: Jessica Chang
Package Outline Dimensions
-+
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
EVERLIGHT ELECTRONICS CO.,LTD.
17-21UYOC/S530-XX/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 3 of 9
Device No. :DSE-171-065 Prepared date: 17-Jan-2005 Prepared by: Jessica Chang
Absolute Maximum Ratings (Ta=25℃)
Parameter Symbol Rating Unit
Reverse Voltage VR 5 V
Forward Current IF 25 mA
Operating Temperature Topr -40 ~ +85 ℃
Storage Temperature Tstg -40~ +90 ℃
Soldering Temperature Tsol 260
(for 5 second) ℃
Electrostatic Discharge ESD 2000 V
Power Dissipation Pd 60 mW
Peak Forward Current
(Duty 1/10 @1KHz) IFP 60 mA
Electro-Optical Characteristics (Ta=25℃)
Parameter Symbol *Chip
Rank Min. Typ. Max. Unit Condition
A2 15 38 -----
A3 40 62 -----
A4 50 75 -----
A5 60 96 -----
Luminous Intensity Iv
A6 85 124 -----
mcd
Viewing Angle 2θ1/2 ----- ----- 140 ----- deg
Peak Wavelength λp ----- ----- 611 ----- nm
Dominant Wavelength λd ----- ----- 605 -----
nm
Spectrum Radiation
Bandwidth △λ ----- ----- 20 -----
nm
Forward Voltage VF ----- ----- 2.0 2.4 V
IF=20 mA
Reverse Current IR ----- ----- -----
10 μA VR=5V
*17-21UYOC/S530-XX/TR8
Chip Rank
EVERLIGHT ELECTRONICS CO.,LTD.
17-21UYOC/S530-XX/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 4 of 9
Device No. :DSE-171-065 Prepared date: 17-Jan-2005 Prepared by: Jessica Chang
Typical Electro-Optical Characteristics Curves
EVERLIGHT ELECTRONICS CO.,LTD.
17-21UYOC/S530-XX/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 5 of 9
Device No. :DSE-171-065 Prepared date: 17-Jan-2005 Prepared by: Jessica Chang
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
EVERLIGHT ELECTRONICS CO.,LTD.
17-21UYOC/S530-XX/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 6 of 9
Device No. :DSE-171-065 Prepared date: 17-Jan-2005 Prepared by: Jessica Chang
Carrier Tape Dimensions : Loaded quantity 3000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Aluminum moistue-proof bag LabelDesiccant
Label
EVERLIGHT ELECTRONICS CO.,LTD.
17-21UYOC/S530-XX/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 7 of 9
Device No. :DSE-171-065 Prepared date: 17-Jan-2005 Prepared by: Jessica Chang
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level：90%
LTPD：10%
No. Items Test Condition
Test
Hours/Cycles Sample
Size Ac/Re
1 Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec. 6 Min. 22 PCS. 0/1
2 Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles 22 PCS. 0/1
3 Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles 22 PCS. 0/1
4 High Temperature
Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1
5 Low Temperature
Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1
6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1
7 High Temperature /
High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1
EVERLIGHT ELECTRONICS CO.,LTD.
17-21UYOC/S530-XX/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 8 of 9
Device No. :DSE-171-065 Prepared date: 17-Jan-2005 Prepared by: Jessica Chang
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3
seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product is often
started at the time of the hand solder.
EVERLIGHT ELECTRONICS CO.,LTD.
17-21UYOC/S530-XX/TR8
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 9 of 9
Device No. :DSE-171-065 Prepared date: 17-Jan-2005 Prepared by: Jessica Chang
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is
unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed
beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
E
VERLIG
H
T ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com
