DOCUMENT NUMBER NCD-69B6-05 SNP-8 Series Single-Mode Pre-Angle FC CONNECTOR PLUG - for Angled-PC / Easy-assemble type - TECHNICAL SPECIFICATIONS Seiko Instruments Inc. OFC Division. 8, Nakase 1-Chome Mihama-ku, Chiba-shi, Chiba-ken 261-8507 JAPAN Telephone : +81-43-211-1211 Facsimile : +81-43-211-8039 SNP-8 Series Single-Mode Pre-Angle FC CONNECTOR PLUG - for Angled-PC / Easy-assemble type TECHNICAL SPECIFICATIONS DOCUMENT NUMBER NCD-69B6-05 NCD-69B6-01 NCD-69B6-02 NCD-69B6-03 NCD-69B6-04 NCD-69B6-05 September 1996 May 1998 July 1999 April 2000 May 2003 Copyright 1996, 1998,1999, 2000, 2003 by Seiko Instruments Inc. All right reserved. The information contained herein shall not reproduced or disclosed to any third party without the express written consent of SII. The Specifications contained herein are subject to change without notice. SII is a trademark of Seiko Instruments Inc. Please address any questions, comments, and suggestions to: Seiko Instruments USA Inc. Seiko Instruments GmbH Electronics Components Division 2990 West Lomita Boulevard Torrance, CA 90505, U.S.A. Phone: +1-310-517-7780 Facsimile: +1-310-517-7792 OFC Division Siemensstrae 9b D-63263 Neu-Isenburg, Germany Phone: +49-6102-297-0 Facsimile: +49-6102-297-211 Seiko Instruments (H.K.) Ltd. Seiko Instruments Taiwan Inc. Sales Department 4th & 5th Floor, Wyler Center 2 200 Tai Lin Pai Road, Kwai Chung N.T., Kowloon, Hong Kong Phone: +852-2421-8611 Facsimile: +852-2480-5479 Sales Department 4F, No.40, Sec. 2, Min Chuan E. Rd., Taipei 104, Taiwan, R.O.C. Phone: +886-2-2563-5001 Facsimile: +886-2-2521-9519 Seiko Instruments Singapore pte. Ltd. Component Sales Department 2, Marsiling Lane, Singapore, 739144, Singapore Phone: +65-269-1370 Facsimile: +65-269-9729 ii TABLE OF CONTENTS Section 1. PROVISION 1.1. Application Limit 2. PARTS NUMBER 3. GENERAL SPECIFICATIONS 3.1. Parts and Materials 3.2. Physical Dimensions 3.3. General Tolerances 4. PACKING 5. NOTE Page 1 1 1 2 2 2 2 3 3 Table Table 1 Table 2 Table 3 Table 4 Parts Number Parts and Materials Parts and Materials (Mainbody) General Tolerance 1 2 2 2 Figure Figure 1 to 2 SNP-8 Connector Figure 3 to 4 Mainbody Figure 5 to 12 Parts dimensions 3 to 4 5 6 to 7 iii iv 1 PROVISION 1.1 Application Limit These specifications apply to the SNP-8 single-mode pre-angle FC connector plug supplied by SII. 2 PARTS NUMBER Parts number of the connector is shown in Table 1. Table 1 Parts number MODEL Number SNP-8 TYPE Number 8 3 1 2 5 1 B 3 0 2 Hood color 0 without hood 8 Green 0 1 3 6 9 01 J1 Hood Inner Dia without hood,crimping-ring 0.9mm (non flamable) 3.0mm (Plastic) 2.0mm (Plastic) 0.9mm (Plastic) Ferrule Inner Dia S5 to S6 ( 0.125 to 0.126mm ) 3 0 8 B Marking of Hood 0 1 without SII Marking 1 ( Requied ) N type R type compatible Package Bulk Cap without Green PVC Green Ferrule Cap Applicable Hood (mm) 0.9mm (non flamable) 0.9 to 3.0mm (Plastic) 3 GENERAL SPECIFICATIONS 3.1 Parts and Materials Parts and materials are shown in Table 2 to 3. Table 2 No. Part Name 1-1 Mainbody 1-2 See Table 3 2-1 Crimping ring 2-2 3-1 Hood 3-2 3-3 3-4 4-1 Cap 4-2 (1) Aluminum alloy Aluminum alloy Thermal plastic elastomer Thermal plastic elastomer Thermal plastic elastomer Synthetic rubber PP PVC (1) (1) Table 3 No. 5 6 7-1 7-2 8 9 10 Parts and Materials Qty Material 1 See Table 3 Part Name Ferrule Flange Frame Spring Coupling nut Stopper Parts and Materials (Mainbody) Qty Material 1 Zirconia 1 Brass 1 Zinc die-casting 1 1 1 Notes N-type, (#5,6,7-1,8,9,10 Sub-assembled) R-type compatible, (#5,6,7-2,8,9,10 Sub-assembled) for o3.0 mm cord for o2.0 mm cord o3.0mm, UL94V-0, Green o2.0mm, UL94V-0, Green o0.9mm, UL94V-0, Green o0.9mm, UL94V-0, Green Green Green Stainless steel Brass Brass Notes Nickel plating Nickel plating, N-type Nickel plating, R-type compatible Nickel plating Nickel plating 3.2 Physical Dimensions Figure 1 to 2 shows the assembled state of SNP-8 Figure 3 to 4 shows the Mainbody. Figure 5 to 11 show the parts dimensions. - In accordance with IEC 61754-13 Fibre optic connector interface Part 13 : Type FC-PC connector family. 3.3 General Tolerance Permissible deviation in dimensions without tolerance indication is in accordance with JIS B 0405 class m, as shown in Table 4. Table 4 General Tolerance (JIS B 0405 class m) Basic size step [mm] Over Under 0.5 3 3 6 6 30 30 120 Permissible deviation [mm] 0.1 0.1 0.2 0.3 2 4 PACKING The product is packed to prevent damage during shipment. 5. NOTE When discarding this product, please follow the regulation of your own country. 3 note 1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not assembled like this. note 2: This drawing does not include the caps. Unit: mm Figure 1 SNP-8 Connector ( N type) 4 note 1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not assembled like this. note 2: This drawing does not include the caps. Unit: mm Figure 2 SNP-8 Connector ( R type compatible ) 5 Unit: mm Figure 3 #1-1 Mainbody ( N type ) Unit: mm Figure 4 #1-2 Mainbody ( R type compatible ) 6 Unit: mm Figure 5 #2-1 Crimping ring ( for o3.0 mm cord ) Unit: mm Figure 6 #2-2 Crimping ring ( for o2.0 mm cord ) Unit: mm Figure 7 #3-1 Hood ( for o3.0 mm cord ) Figure 8 #3-2 Hood ( for o2.0 mm cord ) Unit: mm 7 Unit: mm Figure 9 #3-3 Hood ( for o0.9 mm buffered fiber ) Figure 10 #3-4 Hood ( for o0.9 mm buffered fiber ) Unit: mm Unit: mm Figure 11 #4-1 Cap ( Ferrule Cap ) Unit: mm Figure 12 #14-2 Cap ( PVC ) 8