TCMT110. Series www.vishay.com Vishay Semiconductors Optocoupler, Phototransistor Output, Single Channel, Half Pitch Mini-Flat Package C E 4 3 FEATURES * Low profile package (half pitch) * AC isolation test voltage 3750 VRMS * Low coupling capacitance of typical 0.3 pF * Current transfer ratio (CTR) selected into groups 1 2 * Low temperature coefficient of CTR A C * Wide ambient temperature range 22628-1 * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 DESCRIPTION APPLICATIONS The TCMT110. series consist of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 4 pin package. * Programmable logic controllers * Modems * Answering machines The elements are mounted on one leadframe providing a fixed distance between input and output for highest safety requirements. * General applications AGENCY APPROVALS * UL1577, file no. E76222, double protection * cUL component acceptance service no. 5A, double protection * DIN EN 60747-5-5 (VDE 0884-5) * FIMKO: FI EN 60950-1:2006 * BSI: BS EN60065:2002 BS EN60950-1:2006 * CQC GB 8898-2011, GB 4943.1-2011 (suitable for installation altitude below 2000 m) ORDERING INFORMATION SSOP-4 T C M T 1 1 0 # PART NUMBER AGENCY CERTIFIED/ PACKAGE CTR (%) 5 mA UL, cUL, FIMKO, 50 to 600 BSI, VDE SSOP-4 7.21 mm 10 mA 40 to 80 63 to 125 100 to 200 160 to 320 50 to 150 100 to 300 TCMT1100 TCMT1101 TCMT1102 TCMT1103 TCMT1104 TCMT1105 TCMT1106 5 mA 80 to 160 130 to 260 200 to 400 TCMT1107, TCMT1108 TCMT1109 TCMT1107T3 (1) Notes * Available only on tape and reel (1) Product is rotated 180 in tape and reel cavity Document Number: 83510 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 3.1, 25-Jun-2018 TCMT110. Series www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage VR 6 V Forward current IF 60 mA Forward surge current tp 10 s IFSM 1.5 A Pdiss 100 mW Tj 125 C Collector emitter voltage VCEO 70 V Emitter collector voltage VECO 7 V mA Power dissipation Junction temperature OUTPUT Collector current Collector peak current tp/T = 0.5, tp 10 ms Power dissipation Junction temperature IC 50 ICM 100 mA Pdiss 150 mW Tj 125 C VISO 3750 VRMS COUPLER AC isolation test voltage (RMS) Related to standard climate 23/50 DIN 50014 Total power dissipation Ptot 250 mW Operating ambient temperature range Tamb -40 to +100 C Storage temperature range Tstg -40 to +125 C Soldering temperature (1) Tsld 260 C Notes * Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability (1) Refer to reflow profile for soldering conditions for surface mounted devices. Also refer to "Assembly Instructions" (www.vishay.com/doc?80054) ELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. IF = 50 mA VF - 1.35 1.6 VR = 0, f = 1 MHz Cj - 8 UNIT INPUT Forward voltage Junction capacitance V pF OUTPUT Collector emitter voltage IC = 100 A VCEO 70 - - V Emitter collector voltage IE = 100 A VECO 7 - - V VCE = 20 V, IF = 0 A ICEO - - 100 nA Collector emitter saturation voltage IF = 10 mA, IC = 1 mA VCEsat - - 0.3 V Cut-off frequency VCE = 5 V, IF = 10 mA, RL = 100 fc - 100 - kHz f = 1 MHz Ck - 0.3 - pF Collector dark current COUPLER Coupling capacitance Note * Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements Document Number: 83510 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 3.1, 25-Jun-2018 TCMT110. Series www.vishay.com Vishay Semiconductors CURRENT TRANSFER RATIO (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT VCE = 5 V, IF = 5 mA TCMT1100 CTR 50 - 600 % TCMT1101 CTR 40 - 80 % TCMT1102 CTR 63 - 125 % TCMT1103 CTR 100 - 200 % TCMT1104 CTR 160 - 320 % TCMT1105 CTR 50 - 150 % TCMT1106 CTR 100 - 300 % TCMT1107 CTR 80 - 160 % TCMT1108 CTR 130 - 260 % TCMT1109 CTR 200 - 400 % VCE = 5 V, IF = 10 mA IC/IF VCE = 5 V, IF = 5 mA SWITCHING CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Delay time PARAMETER VS = 5 V, IC = 2 mA, RL = 100 , (see figure 1) td - 4.0 - s Rise time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 1) tr - 5.5 - s Fall time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 1) tf - 7.0 - s Storage time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 1) ts - 1.5 - s Turn-on time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 1) ton - 9.5 - s Turn-off time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 1) toff - 8.5 - s Turn-on time VS = 5 V, IF = 10 mA, RL = 1 k, (see figure 2) ton - 3.0 - s Turn-off time VS = 5 V, IF = 10 mA, RL = 1 k, (see figure 2) toff - 20.0 - s +5V IF IF 0 IF I C = 2 mA; adjusted through input amplitude tp t 100 % 90 % R G = 50 tp = 0.01 T t p = 50 s Channel I Oscilloscope R L = 1 M C L = 20 pF Channel II 50 10 % 0 tr td 100 Fig. 1 - Test Circuit, Non-Saturated Operation 0 tp td tr t on (= td + tr) Pulse duration Delay time Rise time Turn-on time tf t off ts tf t off (= ts + tf) t Storage time Fall time Turn-off time 96 11698 Fig. 3 - Switching Times +5V I F = 10 mA ts t on 95 10804 IF 0 IC IC R G = 50 tp = 0.01 T t p = 50 s Channel I Channel II 50 Oscilloscope R L 1 M C L 20 pF 1 k 95 10843 Fig. 2 - Test Circuit, Saturated Operation Document Number: 83510 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 3.1, 25-Jun-2018 TCMT110. Series www.vishay.com Vishay Semiconductors SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL Climatic classification According to IEC 68 part 1 Pollution degree According to DIN VDE 0109 Comparative tracking index VALUE UNIT 40 / 110 / 21 2 Insulation group IIIa CTI 175 Maximum rated withstanding isolation voltage According to UL1577, t = 1 min VISO 3750 Maximum transient isolation voltage According to DIN EN 60747-5-5 VIOTM 6000 Vpeak Maximum repetitive peak isolation voltage According to DIN EN 60747-5-5 VIORM 707 Vpeak 1012 Tamb = 25 C, VIO = 500 V Isolation resistance VRMS 1011 RIO Tamb = 100 C, VIO = 500 V 109 Tamb = TS, VIO = 500 V Output safety power PSO 350 mW Input safety current ISI 150 mA Input safety temperature TS 175 C 5 mm Creepage distance 5 mm DTI 0.4 mm Input to output test voltage, method B VIORM x 1.875 = VPR, 100 % production test with tM = 1 s, partial discharge < 5 pC VPR 1326 Vpeak Input to output test voltage, method A VIORM x 1.6 = VPR, 100 % sample test with tM = 10 s, partial discharge < 5 pC VPR 1132 Vpeak Clearance distance Insulation thickness 100 300 Coupled device IF - Forward Current (mA) Ptot - Total Power Dissipation (mW) TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 250 200 Phototransistor 150 IR-diode 100 50 0 0 96 11700 40 80 120 Tamb - Ambient Temperature (C) Fig. 4 - Total Power Dissipation vs. Ambient Temperature 10 Tamb = 110 C Tamb = 75 C Tamb = 25 C Tamb = 0 C Tamb = -55 C 1 0.1 0.6 0.8 1.0 1.2 1.4 1.6 VF - Forward Voltage (V) Fig. 5 - Forward Voltage vs. Forward Current Document Number: 83510 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 3.1, 25-Jun-2018 TCMT110. Series www.vishay.com IC - Collector Current (mA) 55 IF = 35 mA 50 45 IF = 30 mA 40 35 IF = 25 mA 30 IF = 20 mA 25 20 IF = 15 mA 15 10 IF = 10 mA IF = 1 mA 5 IF = 5 mA 0 0 1 2 3 4 5 6 7 8 9 10 NCTR - Normalized CTR (non-saturated) Vishay Semiconductors 1.2 IF = 5 mA 1.0 0.8 0.6 0.4 0.2 0 -60 -40 -20 VCE - Collector Emitter Voltage (non-sat) (V) Fig. 6 - Collector Current vs. Collector Emitter Voltage 20 40 60 80 100 120 Fig. 9 - Normalized Current Transfer Ratio (non-saturated) vs. Ambient Temperature 1.2 NCTR - Normalized CTR (sat) IF = 0 mA ICE0 - Leakage Current (nA) 0 Tamb - Ambient Temperature (C) 10 000 1000 VCE = 40 V 100 10 VCE = 24 V 1 0.1 VCE = 12 V 0.01 IF = 5 mA 1.0 0.8 0.6 0.4 0.2 0 -60 -40 -20 0 20 40 60 IF = 10 mA 10 IF = 5 mA 6 4 IF = 1 mA IF = 2 mA 2 0 0 0.1 0.2 0.3 20 40 60 80 100 120 Fig. 10 - Normalized Current Transfer Ratio (saturated) vs. Ambient Temperature VCEsat - Collector Emitter Voltage (V) 14 8 0 Tamb - Ambient Temperature (C) Fig. 7 - Leakage Current vs. Ambient Temperature 12 Normalized to CTR value: IF = 5 mA, VCE = 5 V, Tamb = 25 C -60 -40 -20 80 100 120 Tamb - Ambient Temperature (C) IC - Collector Current (mA) Normalized to CTR value: IF = 5 mA, VCE = 5 V, Tamb = 25 C 0.4 VCE - Collector Emitter Voltage (V) Fig. 8 - Collector Current vs. Collector Emitter Voltage 0.40 0.35 IF = 10 mA 0.30 Ic = 5 mA 0.25 0.20 Ic = 2 mA 0.15 0.10 0.05 Ic = 1 mA 0.00 -60 -40 -20 0 20 40 60 80 100 120 Tamb - Ambient Temperature (C) Fig. 11 - Collector Emitter Voltage vs. Ambient Temperature Document Number: 83510 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 3.1, 25-Jun-2018 TCMT110. Series www.vishay.com Vishay Semiconductors 1000 Tamb = 0 C 1.2 VCC = 5 V Tamb = -55 C Tamb = 25 C 1.0 FCTR (kHz) NCTR - Normalized CTR (NS) 1.4 0.8 0.6 Tamb = 75 C 0.4 Tamb = 100 C Normalized to: IF = 5 mA, VCE = 5 V, Tamb = 25 C 0.2 0 0.1 1 10 100 10 1 0.1 100 1 IF - Forward Current (mA) Fig. 12 - Normalized CTR (non-saturated) vs. Forward Current 100 Fig. 15 - FCTR vs. Collector Current 1000 1.2 Tamb = 0 C VCE = 0.4 V Normalized to: IF = 5 mA, VCE = 5 V, Tamb = 25 C 1.0 0.8 VCE = 5 V, IC = 2 mA Tamb = -55 - C 0.6 0.4 Tamb = 25 C 0.2 Tamb = 75 C Tamb = 100 C 0 0.1 1 10 ton, toff Switching Time (s) NCTR - Normalized CTR (sat) 10 IC (mA) 100 toff (s) 10 1 ton (s) 0.1 100 0 5 10 15 20 RL - Load Resistance (k) IF - Forward Current (mA) Fig. 13 - Normalized CTR (saturated) vs. Forward Current Fig. 16 - Switching Time vs. Load Resistance 0 VCE = 5 V -20 RL = 100 Phase Angle (deg) -40 RL = 1000 -60 -80 -100 -120 -140 -160 1 10 100 1000 f - Frequency (kHz) Fig. 14 - FCTR vs. Phase Angle Document Number: 83510 6 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 3.1, 25-Jun-2018 TCMT110. Series www.vishay.com Vishay Semiconductors 0.60 0.10 0.10 0.4 0.1 4.40 typ. 0.2 0.05 2.85 max. 2.60 0.20 2.00 0.10 PACKAGE DIMENSIONS in millimeters 1.27 nom. 4 + 0.20 - 0.30 7.00 0.30 Lead coplanarity 0.1 max. 3 1.27 0.9 Possible footprint 5.00 7.60 Pin One I.D. 1 2 PACKAGE MARKING (example) MT1100 V YWW 68 TAPE AND REEL PACKAGING in millimeters 2 0.1 0.3 0.05 4 0.1 1.55 0.05 1.75 0.1 Pin 1 7.5 0.1 16 0.3 4.4 7.4 0.1 7.4 0.1 5 2.2 0.1 2.6 0.1 8 0.1 2.95 0.1 1.6 0.1 Fig. 17 Document Number: 83510 7 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 3.1, 25-Jun-2018 TCMT110. Series www.vishay.com Vishay Semiconductors SOLDER PROFILES HANDLING AND STORAGE CONDITIONS ESD level: HBM class 2 Axis Title 10000 300 Floor life: unlimited Max. 260 C 255 C 240 C 217 C Conditions: Tamb < 30 C, RH < 85 % 245 C Moisture sensitivity level 1, according to J-STD-020 1000 200 Max. 30 s 1st line 2nd line 2nd line Temperature (C) 250 150 Max. 120 s 100 Max. 100 s Max. ramp down 6 C/s 100 Max. ramp up 3 C/s 50 10 0 0 50 100 150 200 250 300 Time (s) 19841 Fig. 18 - Lead (Pb)-free Reflow Solder Profile According to J-STD-020 for SMD Devices Document Number: 83510 8 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 3.1, 25-Jun-2018 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000