Includes FLEX 10KA FLEX 10K Embedded Programmable Logic Device Family (R) March 2001, ver. 4.1 Features... Data Sheet The industry's first embedded programmable logic device (PLD) family, providing System-on-a-Programmable-Chip (SOPC) integration - Embedded array for implementing megafunctions, such as efficient memory and specialized logic functions - Logic array for general logic functions High density - 10,000 to 250,000 typical gates (see Tables 1 and 2) - Up to 40,960 RAM bits; 2,048 bits per embedded array block (EAB), all of which can be used without reducing logic capacity System-level features - MultiVoltTM I/O interface support - 5.0-V tolerant input pins in FLEX(R) 10KA devices - Low power consumption (typical specification less than 0.5 mA in standby mode for most devices) - FLEX 10K and FLEX 10KA devices support peripheral component interconnect Special Interest Group (PCI SIG) PCI Local Bus Specification, Revision 2.2 - FLEX 10KA devices include pull-up clamping diode, selectable on a pin-by-pin basis for 3.3-V PCI compliance - Select FLEX 10KA devices support 5.0-V PCI buses with eight or fewer loads - Built-in Joint Test Action Group (JTAG) boundary-scan test (BST) circuitry compliant with IEEE Std. 1149.1-1990, available without consuming any device logic Table 1. FLEX 10K Device Features Feature EPF10K10 EPF10K10A EPF10K20 EPF10K30 EPF10K30A EPF10K40 EPF10K50 EPF10K50V Typical gates (logic and RAM) (1) 10,000 20,000 30,000 40,000 50,000 Maximum system gates 31,000 63,000 69,000 93,000 116,000 Logic elements (LEs) 576 1,152 1,728 2,304 2,880 Logic array blocks (LABs) 72 144 216 288 360 Embedded array blocks (EABs) 3 6 6 8 10 6,144 12,288 12,288 16,384 20,480 150 189 246 189 310 Total RAM bits Maximum user I/O pins Altera Corporation A-DS-F10K-04.1 1 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 2. FLEX 10K Device Features Feature EPF10K70 EPF10K100 EPF10K100A EPF10K130V EPF10K250A Typical gates (logic and RAM) (1) 70,000 100,000 130,000 250,000 Maximum system gates 118,000 158,000 211,000 310,000 3,744 4,992 6,656 12,160 468 624 832 1,520 LEs LABs EABs Total RAM bits Maximum user I/O pins 9 12 16 20 18,432 24,576 32,768 40,960 358 406 470 470 Note to tables: (1) The embedded IEEE Std. 1149.1 JTAG circuitry adds up to 31,250 gates in addition to the listed typical or maximum system gates. ...and More Features - - - - - Devices are fabricated on advanced processes and operate with a 3.3-V or 5.0-V supply voltage (see Table 3 In-circuit reconfigurability (ICR) via external configuration device, intelligent controller, or JTAG port ClockLockTM and ClockBoostTM options for reduced clock delay/skew and clock multiplication Built-in low-skew clock distribution trees 100% functional testing of all devices; test vectors or scan chains are not required Table 3. Supply Voltages for FLEX 10K & FLEX 10KA Devices 2 5.0-V Devices 3.3-V Devices EPF10K10 EPF10K20 EPF10K30 EPF10K40 EPF10K50 EPF10K70 EPF10K100 EPF10K10A EPF10K30A EPF10K50V EPF10K100A EPF10K130V EPF10K250A Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Altera Corporation Flexible interconnect - FastTrack(R) Interconnect continuous routing structure for fast, predictable interconnect delays - Dedicated carry chain that implements arithmetic functions such as fast adders, counters, and comparators (automatically used by software tools and megafunctions) - Dedicated cascade chain that implements high-speed, high-fan-in logic functions (automatically used by software tools and megafunctions) - Tri-state emulation that implements internal tri-state buses - Up to six global clock signals and four global clear signals Powerful I/O pins - Individual tri-state output enable control for each pin - Open-drain option on each I/O pin - Programmable output slew-rate control to reduce switching noise - FLEX 10KA devices support hot-socketing Peripheral register for fast setup and clock-to-output delay Flexible package options - Available in a variety of packages with 84 to 600 pins (see Tables 4 and 5) - Pin-compatibility with other FLEX 10K devices in the same package - FineLine BGATM packages maximize board space efficiency Software design support and automatic place-and-route provided by Altera development systems for Windows-based PCs and Sun SPARCstation, HP 9000 Series 700/800 workstations Additional design entry and simulation support provided by EDIF 2 0 0 and 3 0 0 netlist files, library of parameterized modules (LPM), DesignWare components, Verilog HDL, VHDL, and other interfaces to popular EDA tools from manufacturers such as Cadence, Exemplar Logic, Mentor Graphics, OrCAD, Synopsys, Synplicity, VeriBest, and Viewlogic 3 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 4. FLEX 10K Package Options & I/O Pin Count Device 84-Pin PLCC EPF10K10 100-Pin TQFP Note (1) 208-Pin PQFP RQFP 102 134 102 134 102 147 189 147 189 147 189 147 189 59 EPF10K10A 240-Pin PQFP RQFP 144-Pin TQFP 66 EPF10K20 EPF10K30 EPF10K30A 102 EPF10K40 EPF10K50 189 EPF10K50V 189 EPF10K70 189 EPF10K100 EPF10K100A 189 EPF10K130V EPF10K250A Table 5. FLEX 10K Package Options & I/O Pin Count (Continued) Device 503-Pin 599-Pin PGA PGA 256-Pin FineLine BGA 356-Pin BGA Note (1) 484-Pin FineLine BGA 600-Pin BGA 403-Pin PGA EPF10K10 EPF10K10A 150 (2) 150 EPF10K20 EPF10K30 246 EPF10K30A 191 246 246 EPF10K40 EPF10K50 274 EPF10K50V 274 EPF10K70 358 EPF10K100 406 EPF10K100A 4 310 274 369 406 EPF10K130V 470 470 EPF10K250A 470 470 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) FLEX 10K and FLEX 10KA device package types include plastic J-lead chip carrier (PLCC), thin quad flat pack (TQFP), plastic quad flat pack (PQFP), power quad flat pack (RQFP), ball-grid array (BGA), pin-grid array (PGA), and FineLine BGATM packages. This option is supported with a 256-pin FineLine BGA package. By using SameFrame pin migration, all FineLine BGA packages are pin compatible. For example, a board can be designed to support both 256-pin and 484-pin FineLine BGA packages. The Altera software automatically avoids conflicting pins when future migration is set. General Description Altera's FLEX 10K devices are the industry's first embedded PLDs. Based on reconfigurable CMOS SRAM elements, the Flexible Logic Element MatriX (FLEX) architecture incorporates all features necessary to implement common gate array megafunctions. With up to 250,000 gates, the FLEX 10K family provides the density, speed, and features to integrate entire systems, including multiple 32-bit buses, into a single device. FLEX 10K devices are reconfigurable, which allows 100% testing prior to shipment. As a result, the designer is not required to generate test vectors for fault coverage purposes. Additionally, the designer does not need to manage inventories of different ASIC designs; FLEX 10K devices can be configured on the board for the specific functionality required. Table 6 shows FLEX 10K performance for some common designs. All performance values were obtained with Synopsys DesignWare or LPM functions. No special design technique was required to implement the applications; the designer simply inferred or instantiated a function in a Verilog HDL, VHDL, Altera Hardware Description Language (AHDL), or schematic design file. Table 6. FLEX 10K & FLEX 10KA Performance Application Resources Used Performance Units LEs EABs -1 Speed Grade -2 Speed Grade -3 Speed Grade -4 Speed Grade 16-bit loadable counter (1) 16 0 204 166 125 95 MHz 16-bit accumulator (1) 16 0 204 166 125 95 MHz 16-to-1 multiplexer (2) 10 0 4.2 5.8 6.0 7.0 ns 256 x 8 RAM read cycle speed (3) 0 1 172 145 108 84 MHz 256 x 8 RAM write cycle speed (3) 0 1 106 89 68 63 MHz Notes: (1) (2) (3) The speed grade of this application is limited because of clock high and low specifications. This application uses combinatorial inputs and outputs. This application uses registered inputs and outputs. Altera Corporation 5 FLEX 10K Embedded Programmable Logic Device Family Data Sheet The FLEX 10K architecture is similar to that of embedded gate arrays, the fastest-growing segment of the gate array market. As with standard gate arrays, embedded gate arrays implement general logic in a conventional "sea-of-gates" architecture. In addition, embedded gate arrays have dedicated die areas for implementing large, specialized functions. By embedding functions in silicon, embedded gate arrays provide reduced die area and increased speed compared to standard gate arrays. However, embedded megafunctions typically cannot be customized, limiting the designer's options. In contrast, FLEX 10K devices are programmable, providing the designer with full control over embedded megafunctions and general logic while facilitating iterative design changes during debugging. Each FLEX 10K device contains an embedded array and a logic array. The embedded array is used to implement a variety of memory functions or complex logic functions, such as digital signal processing (DSP), microcontroller, wide-data-path manipulation, and data-transformation functions. The logic array performs the same function as the sea-of-gates in the gate array: it is used to implement general logic, such as counters, adders, state machines, and multiplexers. The combination of embedded and logic arrays provides the high performance and high density of embedded gate arrays, enabling designers to implement an entire system on a single device. FLEX 10K devices are configured at system power-up with data stored in an Altera serial configuration device or provided by a system controller. Altera offers the EPC1, EPC2, EPC16, and EPC1441 configuration devices, which configure FLEX 10K devices via a serial data stream. Configuration data can also be downloaded from system RAM or from Altera's BitBlasterTM serial download cable or ByteBlasterMVTM parallel port download cable. After a FLEX 10K device has been configured, it can be reconfigured in-circuit by resetting the device and loading new data. Because reconfiguration requires less than 320 ms, real-time changes can be made during system operation. FLEX 10K devices contain an optimized interface that permits microprocessors to configure FLEX 10K devices serially or in parallel, and synchronously or asynchronously. The interface also enables microprocessors to treat a FLEX 10K device as memory and configure the device by writing to a virtual memory location, making it very easy for the designer to reconfigure the device. 6 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet f For more information, see the following documents: Configuration Devices for APEX & FLEX Devices Data Sheet BitBlaster Serial Download Cable Data Sheet ByteBlasterMV Parallel Port Download Cable Data Sheet Application Note 116 (Configuring APEX 20K, FLEX 10K & FLEX 6000 Devices) FLEX 10K devices are supported by Altera development systems; single, integrated packages that offer schematic, text (including AHDL), and waveform design entry, compilation and logic synthesis, full simulation and worst-case timing analysis, and device configuration. The Altera software provides EDIF 2 0 0 and 3 0 0, LPM, VHDL, Verilog HDL, and other interfaces for additional design entry and simulation support from other industry-standard PC- and UNIX workstation-based EDA tools. The Altera software works easily with common gate array EDA tools for synthesis and simulation. For example, the Altera software can generate Verilog HDL files for simulation with tools such as Cadence Verilog-XL. Additionally, the Altera software contains EDA libraries that use devicespecific features such as carry chains which are used for fast counter and arithmetic functions. For instance, the Synopsys Design Compiler library supplied with the Altera development systems include DesignWare functions that are optimized for the FLEX 10K architecture. The Altera development systems run on Windows-based PCs and Sun SPARCstation, and HP 9000 Series 700/800 workstations. f Functional Description See the MAX+PLUS II Programmable Logic Development System & Software Data Sheet for more information. Each FLEX 10K device contains an embedded array to implement memory and specialized logic functions, and a logic array to implement general logic. The embedded array consists of a series of EABs. When implementing memory functions, each EAB provides 2,048 bits, which can be used to create RAM, ROM, dual-port RAM, or first-in first-out (FIFO) functions. When implementing logic, each EAB can contribute 100 to 600 gates towards complex logic functions, such as multipliers, microcontrollers, state machines, and DSP functions. EABs can be used independently, or multiple EABs can be combined to implement larger functions. Altera Corporation 7 FLEX 10K Embedded Programmable Logic Device Family Data Sheet The logic array consists of logic array blocks (LABs). Each LAB contains eight LEs and a local interconnect. An LE consists of a 4-input look-up table (LUT), a programmable flipflop, and dedicated signal paths for carry and cascade functions. The eight LEs can be used to create medium-sized blocks of logic--8-bit counters, address decoders, or state machines--or combined across LABs to create larger logic blocks. Each LAB represents about 96 usable gates of logic. Signal interconnections within FLEX 10K devices and to and from device pins are provided by the FastTrack Interconnect, a series of fast, continuous row and column channels that run the entire length and width of the device. Each I/O pin is fed by an I/O element (IOE) located at the end of each row and column of the FastTrack Interconnect. Each IOE contains a bidirectional I/O buffer and a flipflop that can be used as either an output or input register to feed input, output, or bidirectional signals. When used with a dedicated clock pin, these registers provide exceptional performance. As inputs, they provide setup times as low as 1.6 ns and hold times of 0 ns; as outputs, these registers provide clock-to-output times as low as 5.3 ns. IOEs provide a variety of features, such as JTAG BST support, slew-rate control, tri-state buffers, and open-drain outputs. Figure 1 shows a block diagram of the FLEX 10K architecture. Each group of LEs is combined into an LAB; LABs are arranged into rows and columns. Each row also contains a single EAB. The LABs and EABs are interconnected by the FastTrack Interconnect. IOEs are located at the end of each row and column of the FastTrack Interconnect. 8 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 1. FLEX 10K Device Block Diagram Embedded Array Block (EAB) I/O Element (IOE) IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE Column Interconnect Logic Array EAB Logic Array Block (LAB) IOE IOE IOE IOE Logic Element (LE) Row Interconnect EAB Local Interconnect Logic Array IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE Embedded Array FLEX 10K devices provide six dedicated inputs that drive the flipflops' control inputs to ensure the efficient distribution of high-speed, low-skew (less than 1.5 ns) control signals. These signals use dedicated routing channels that provide shorter delays and lower skews than the FastTrack Interconnect. Four of the dedicated inputs drive four global signals. These four global signals can also be driven by internal logic, providing an ideal solution for a clock divider or an internally generated asynchronous clear signal that clears many registers in the device. Embedded Array Block The EAB is a flexible block of RAM with registers on the input and output ports, and is used to implement common gate array megafunctions. The EAB is also suitable for functions such as multipliers, vector scalars, and error correction circuits, because it is large and flexible. These functions can be combined in applications such as digital filters and microcontrollers. Altera Corporation 9 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Logic functions are implemented by programming the EAB with a readonly pattern during configuration, creating a large LUT. With LUTs, combinatorial functions are implemented by looking up the results, rather than by computing them. This implementation of combinatorial functions can be faster than using algorithms implemented in general logic, a performance advantage that is further enhanced by the fast access times of EABs. The large capacity of EABs enables designers to implement complex functions in one logic level without the routing delays associated with linked LEs or field-programmable gate array (FPGA) RAM blocks. For example, a single EAB can implement a 4 x 4 multiplier with eight inputs and eight outputs. Parameterized functions such as LPM functions can automatically take advantage of the EAB. The EAB provides advantages over FPGAs, which implement on-board RAM as arrays of small, distributed RAM blocks. These FPGA RAM blocks contain delays that are less predictable as the size of the RAM increases. In addition, FPGA RAM blocks are prone to routing problems because small blocks of RAM must be connected together to make larger blocks. In contrast, EABs can be used to implement large, dedicated blocks of RAM that eliminate these timing and routing concerns. EABs can be used to implement synchronous RAM, which is easier to use than asynchronous RAM. A circuit using asynchronous RAM must generate the RAM write enable (WE) signal, while ensuring that its data and address signals meet setup and hold time specifications relative to the WE signal. In contrast, the EAB's synchronous RAM generates its own WE signal and is self-timed with respect to the global clock. A circuit using the EAB's self-timed RAM need only meet the setup and hold time specifications of the global clock. When used as RAM, each EAB can be configured in any of the following sizes: 256 x 8, 512 x 4, 1,024 x 2, or 2,048 x 1. See Figure 2. Figure 2. EAB Memory Configurations 256 x 8 10 512 x 4 1,024 x 2 2,048 x 1 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Larger blocks of RAM are created by combining multiple EABs. For example, two 256 x 8 RAM blocks can be combined to form a 256 x 16 RAM block; two 512 x 4 blocks of RAM can be combined to form a 512 x 8 RAM block. See Figure 3. Figure 3. Examples of Combining EABs 256 x 16 512 x 8 256 x 8 512 x 4 256 x 8 512 x 4 If necessary, all EABs in a device can be cascaded to form a single RAM block. EABs can be cascaded to form RAM blocks of up to 2,048 words without impacting timing. Altera's software automatically combines EABs to meet a designer's RAM specifications. EABs provide flexible options for driving and controlling clock signals. Different clocks can be used for the EAB inputs and outputs. Registers can be independently inserted on the data input, EAB output, or the address and WE inputs. The global signals and the EAB local interconnect can drive the WE signal. The global signals, dedicated clock pins, and EAB local interconnect can drive the EAB clock signals. Because the LEs drive the EAB local interconnect, the LEs can control the WE signal or the EAB clock signals. Each EAB is fed by a row interconnect and can drive out to row and column interconnects. Each EAB output can drive up to two row channels and up to two column channels; the unused row channel can be driven by other LEs. This feature increases the routing resources available for EAB outputs. See Figure 4. Altera Corporation 11 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 4. FLEX 10K Embedded Array Block Dedicated Inputs & Global Signals Chip-Wide Reset Row Interconnect (1) 2, 4, 8, 16 6 D Q Data In Data Out D 24 Q 8, 4, 2, 1 2, 4, 8, 16 Address D Q 8, 9, 10, 11 RAM/ROM 256 x 8 512 x 4 1,024 x 2 2,048 x 1 Column Interconnect WE D Q EAB Local Interconnect (1) Note: (1) EPF10K10, EPF10K10A, EPF10K20, EPF10K30, EPF10K30A, EPF10K40, EPF10K50, and EPF10K50V devices have 22 EAB local interconnect channels; EPF10K70, EPF10K100, EPF10K100A, EPF10K130V, and EPF10K250A devices have 26. 12 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Logic Array Block Each LAB consists of eight LEs, their associated carry and cascade chains, LAB control signals, and the LAB local interconnect. The LAB provides the coarse-grained structure to the FLEX 10K architecture, facilitating efficient routing with optimum device utilization and high performance. See Figure 5. Figure 5. FLEX 10K LAB Dedicated Inputs & Global Signals (1) LAB Local Interconnect (2) Row Interconnect 6 16 4 See Figure 11 for details. 4 LAB Control Signals 4 Carry-In & Cascade-In 2 4 LE1 4 LE2 4 LE3 4 LE4 4 LE5 4 LE6 4 LE7 4 LE8 8 2 8 24 Column-to-Row Interconnect Column Interconnect 8 16 Carry-Out & Cascade-Out Notes: (1) (2) EPF10K10, EPF10K10A, EPF10K20, EPF10K30, EPF10K30A, EPF10K40, EPF10K50, and EPF10K50V devices have 22 inputs to the LAB local interconnect channel from the row; EPF10K70, EPF10K100, EPF10K100A, EPF10K130V, and EPF10K250A devices have 26. EPF10K10, EPF10K10A, EPF10K20, EPF10K30, EPF10K30A, EPF10K40, EPF10K50, and EPF10K50V devices have 30 LAB local interconnect channels; EPF10K70, EPF10K100, EPF10K100A, EPF10K130V, and EPF10K250A devices have 34 LABs. Altera Corporation 13 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Each LAB provides four control signals with programmable inversion that can be used in all eight LEs. Two of these signals can be used as clocks; the other two can be used for clear/preset control. The LAB clocks can be driven by the dedicated clock input pins, global signals, I/O signals, or internal signals via the LAB local interconnect. The LAB preset and clear control signals can be driven by the global signals, I/O signals, or internal signals via the LAB local interconnect. The global control signals are typically used for global clock, clear, or preset signals because they provide asynchronous control with very low skew across the device. If logic is required on a control signal, it can be generated in one or more LEs in any LAB and driven into the local interconnect of the target LAB. In addition, the global control signals can be generated from LE outputs. Logic Element The LE, the smallest unit of logic in the FLEX 10K architecture, has a compact size that provides efficient logic utilization. Each LE contains a four-input LUT, which is a function generator that can quickly compute any function of four variables. In addition, each LE contains a programmable flipflop with a synchronous enable, a carry chain, and a cascade chain. Each LE drives both the local and the FastTrack Interconnect. See Figure 6. Figure 6. FLEX 10K Logic Element Carry-In data1 data2 data3 data4 Look-Up Table (LUT) Carry Chain Cascade-In Cascade Chain Register Bypass D PRN Q Programmable Register To FastTrack Interconnect ENA CLRN To LAB Local Interconnect labctrl1 labctrl2 Clear/ Preset Logic Chip-Wide Reset Clock Select labctrl3 labctrl4 Carry-Out 14 Cascade-Out Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet The programmable flipflop in the LE can be configured for D, T, JK, or SR operation. The clock, clear, and preset control signals on the flipflop can be driven by global signals, general-purpose I/O pins, or any internal logic. For combinatorial functions, the flipflop is bypassed and the output of the LUT drives the output of the LE. The LE has two outputs that drive the interconnect; one drives the local interconnect and the other drives either the row or column FastTrack Interconnect. The two outputs can be controlled independently. For example, the LUT can drive one output while the register drives the other output. This feature, called register packing, can improve LE utilization because the register and the LUT can be used for unrelated functions. The FLEX 10K architecture provides two types of dedicated high-speed data paths that connect adjacent LEs without using local interconnect paths: carry chains and cascade chains. The carry chain supports highspeed counters and adders; the cascade chain implements wide-input functions with minimum delay. Carry and cascade chains connect all LEs in an LAB and all LABs in the same row. Intensive use of carry and cascade chains can reduce routing flexibility. Therefore, the use of these chains should be limited to speed-critical portions of a design. Carry Chain The carry chain provides a very fast (as low as 0.2 ns) carry-forward function between LEs. The carry-in signal from a lower-order bit drives forward into the higher-order bit via the carry chain, and feeds into both the LUT and the next portion of the carry chain. This feature allows the FLEX 10K architecture to implement high-speed counters, adders, and comparators of arbitrary width efficiently. Carry chain logic can be created automatically by the Compiler during design processing, or manually by the designer during design entry. Parameterized functions such as LPM and DesignWare functions automatically take advantage of carry chains. Carry chains longer than eight LEs are automatically implemented by linking LABs together. For enhanced fitting, a long carry chain skips alternate LABs in a row. A carry chain longer than one LAB skips either from even-numbered LAB to even-numbered LAB, or from oddnumbered LAB to odd-numbered LAB. For example, the last LE of the first LAB in a row carries to the first LE of the third LAB in the row. The carry chain does not cross the EAB at the middle of the row. For instance, in the EPF10K50 device, the carry chain stops at the eighteenth LAB and a new one begins at the nineteenth LAB. Altera Corporation 15 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 7 shows how an n-bit full adder can be implemented in n + 1 LEs with the carry chain. One portion of the LUT generates the sum of two bits using the input signals and the carry-in signal; the sum is routed to the output of the LE. The register can either be bypassed for simple adders or be used for an accumulator function. The carry chain logic generates the carry-out signal, which is routed directly to the carry-in signal of the nexthigher-order bit. The final carry-out signal is routed to an LE, where it can be used as a general-purpose signal. Figure 7. Carry Chain Operation (n-bit Full Adder) Carry-In a1 b1 LUT s1 Register Carry Chain LE1 a2 b2 LUT s2 Register Carry Chain LE2 an bn LUT sn Register Carry Chain LEn LUT Register Carry-Out Carry Chain LEn + 1 16 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Cascade Chain With the cascade chain, the FLEX 10K architecture can implement functions that have a very wide fan-in. Adjacent LUTs can be used to compute portions of the function in parallel; the cascade chain serially connects the intermediate values. The cascade chain can use a logical AND or logical OR (via De Morgan's inversion) to connect the outputs of adjacent LEs. Each additional LE provides four more inputs to the effective width of a function, with a delay as low as 0.7 ns per LE. Cascade chain logic can be created automatically by the Compiler during design processing, or manually by the designer during design entry. Cascade chains longer than eight bits are implemented automatically by linking several LABs together. For easier routing, a long cascade chain skips every other LAB in a row. A cascade chain longer than one LAB skips either from even-numbered LAB to even-numbered LAB, or from odd-numbered LAB to odd-numbered LAB (e.g., the last LE of the first LAB in a row cascades to the first LE of the third LAB). The cascade chain does not cross the center of the row (e.g., in the EPF10K50 device, the cascade chain stops at the eighteenth LAB and a new one begins at the nineteenth LAB). This break is due to the EAB's placement in the middle of the row. Figure 8 shows how the cascade function can connect adjacent LEs to form functions with a wide fan-in. These examples show functions of 4n variables implemented with n LEs. The LE delay is as low as 1.6 ns; the cascade chain delay is as low as 0.7 ns. With the cascade chain, 3.7 ns is needed to decode a 16-bit address. Figure 8. Cascade Chain Operation AND Cascade Chain d[3..0] OR Cascade Chain d[3..0] LUT LUT LE1 d[7..4] LE1 d[7..4] LUT LUT LE2 d[(4n-1)..(4n-4)] d[(4n-1)..(4n-4)] LUT LEn Altera Corporation LE2 LUT LEn 17 FLEX 10K Embedded Programmable Logic Device Family Data Sheet LE Operating Modes The FLEX 10K LE can operate in the following four modes: Normal mode Arithmetic mode Up/down counter mode Clearable counter mode Each of these modes uses LE resources differently. In each mode, seven available inputs to the LE--the four data inputs from the LAB local interconnect, the feedback from the programmable register, and the carry-in and cascade-in from the previous LE--are directed to different destinations to implement the desired logic function. Three inputs to the LE provide clock, clear, and preset control for the register. The Altera software, in conjunction with parameterized functions such as LPM and DesignWare functions, automatically chooses the appropriate mode for common functions such as counters, adders, and multipliers. If required, the designer can also create special-purpose functions which use a specific LE operating mode for optimal performance. The architecture provides a synchronous clock enable to the register in all four modes. The Altera software can set DATA1 to enable the register synchronously, providing easy implementation of fully synchronous designs. Figure 9 shows the LE operating modes. 18 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 9. FLEX 10K LE Operating Modes Normal Mode Cascade-In (1) Carry-In LE-Out to FastTrack Interconnect data1 data2 4-Input LUT data3 D PRN Q LE-Out to Local Interconnect ENA CLRN data4 Cascade-Out Arithmetic Mode Carry-In Cascade-In LE-Out data1 data2 PRN D Q 3-Input LUT ENA CLRN 3-Input LUT Cascade-Out Carry-Out Up/Down Counter Mode Cascade-In Carry-In data1 (ena) data2 (u/d) 3-Input LUT 1 D PRN Q LE-Out 0 data3 (data) ENA CLRN 3-Input LUT data4 (nload) Carry-Out Cascade-Out Clearable Counter Mode Carry-In data1 (ena) data2 (nclr) 3-Input LUT D 1 PRN Q LE-Out 0 data3 (data) ENA CLRN 3-Input LUT data4 (nload) Carry-Out Cascade-Out Note: (1) Packed registers cannot be used with the cascade chain. Altera Corporation 19 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Normal Mode The normal mode is suitable for general logic applications and wide decoding functions that can take advantage of a cascade chain. In normal mode, four data inputs from the LAB local interconnect and the carry-in are inputs to a four-input LUT. The Compiler automatically selects the carry-in or the DATA3 signal as one of the inputs to the LUT. The LUT output can be combined with the cascade-in signal to form a cascade chain through the cascade-out signal. Either the register or the LUT can be used to drive both the local interconnect and the FastTrack Interconnect at the same time. The LUT and the register in the LE can be used independently; this feature is known as register packing. To support register packing, the LE has two outputs; one drives the local interconnect and the other drives the FastTrack Interconnect. The DATA4 signal can drive the register directly, allowing the LUT to compute a function that is independent of the registered signal; a three-input function can be computed in the LUT, and a fourth independent signal can be registered. Alternatively, a four-input function can be generated, and one of the inputs to this function can be used to drive the register. The register in a packed LE can still use the clock enable, clear, and preset signals in the LE. In a packed LE, the register can drive the FastTrack Interconnect while the LUT drives the local interconnect, or vice versa. Arithmetic Mode The arithmetic mode offers 2 three-input LUTs that are ideal for implementing adders, accumulators, and comparators. One LUT computes a three-input function, and the other generates a carry output. As shown in Figure 9 on page 19, the first LUT uses the carry-in signal and two data inputs from the LAB local interconnect to generate a combinatorial or registered output. For example, in an adder, this output is the sum of three signals: a, b, and carry-in. The second LUT uses the same three signals to generate a carry-out signal, thereby creating a carry chain. The arithmetic mode also supports simultaneous use of the cascade chain. 20 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Up/Down Counter Mode The up/down counter mode offers counter enable, clock enable, synchronous up/down control, and data loading options. These control signals are generated by the data inputs from the LAB local interconnect, the carry-in signal, and output feedback from the programmable register. The Up/down counter mode uses 2 three-input LUTs: one generates the counter data, and the other generates the fast carry bit. A 2-to-1 multiplexer provides synchronous loading. Data can also be loaded asynchronously with the clear and preset register control signals, without using the LUT resources. Clearable Counter Mode The clearable counter mode is similar to the up/down counter mode, but supports a synchronous clear instead of the up/down control. The clear function is substituted for the cascade-in signal in the up/down counter mode. Clearable counter mode uses 2 three-input LUTs: one generates the counter data, and the other generates the fast carry bit. Synchronous loading is provided by a 2-to-1 multiplexer. The output of this multiplexer is ANDed with a synchronous clear signal. Internal Tri-State Emulation Internal tri-state emulation provides internal tri-stating without the limitations of a physical tri-state bus. In a physical tri-state bus, the tri-state buffers' output enable (OE) signals select which signal drives the bus. However, if multiple OE signals are active, contending signals can be driven onto the bus. Conversely, if no OE signals are active, the bus will float. Internal tri-state emulation resolves contending tri-state buffers to a low value and floating buses to a high value, thereby eliminating these problems. The Altera software automatically implements tri-state bus functionality with a multiplexer. Clear & Preset Logic Control Logic for the programmable register's clear and preset functions is controlled by the DATA3, LABCTRL1, and LABCTRL2 inputs to the LE. The clear and preset control structure of the LE asynchronously loads signals into a register. Either LABCTRL1 or LABCTRL2 can control the asynchronous clear. Alternatively, the register can be set up so that LABCTRL1 implements an asynchronous load. The data to be loaded is driven to DATA3; when LABCTRL1 is asserted, DATA3 is loaded into the register. Altera Corporation 21 FLEX 10K Embedded Programmable Logic Device Family Data Sheet During compilation, the Compiler automatically selects the best control signal implementation. Because the clear and preset functions are activelow, the Compiler automatically assigns a logic high to an unused clear or preset. The clear and preset logic is implemented in one of the following six modes chosen during design entry: Asynchronous clear Asynchronous preset Asynchronous clear and preset Asynchronous load with clear Asynchronous load with preset Asynchronous load without clear or preset In addition to the six clear and preset modes, FLEX 10K devices provide a chip-wide reset pin that can reset all registers in the device. Use of this feature is set during design entry. In any of the clear and preset modes, the chip-wide reset overrides all other signals. Registers with asynchronous presets may be preset when the chip-wide reset is asserted. Inversion can be used to implement the asynchronous preset. Figure 10 shows examples of how to enter a section of a design for the desired functionality. 22 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 10. LE Clear & Preset Modes Asynchronous Clear Asynchronous Preset Asynchronous Clear & Preset labctrl1 VCC D PRN Q Chip-Wide Reset labctrl1 or labctrl2 D D PRN Q PRN Q CLRN CLRN labctrl1 or labctrl2 Chip-Wide Reset labctrl2 Chip-Wide Reset CLRN VCC Asynchronous Load without Clear or Preset Asynchronous Load with Clear NOT NOT labctrl1 (Asynchronous Load) labctrl1 (Asynchronous Load) data3 (Data) D NOT PRN Q data3 (Data) D PRN Q CLRN CLRN labctrl2 (Clear) Chip-Wide Reset NOT Chip-Wide Reset Asynchronous Load with Preset NOT labctrl1 (Asynchronous Load) labctrl2 (Preset) D data3 (Data) PRN Q CLRN NOT Chip-Wide Reset Asynchronous Clear The flipflop can be cleared by either LABCTRL1 or LABCTRL2. In this mode, the preset signal is tied to VCC to deactivate it. Altera Corporation 23 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Asynchronous Preset An asynchronous preset is implemented as either an asynchronous load, or with an asynchronous clear. If DATA3 is tied to VCC, asserting LABCTRL1 asynchronously loads a one into the register. Alternatively, the Altera software can provide preset control by using the clear and inverting the input and output of the register. Inversion control is available for the inputs to both LEs and IOEs. Therefore, if a register is preset by only one of the two LABCTRL signals, the DATA3 input is not needed and can be used for one of the LE operating modes. Asynchronous Preset & Clear When implementing asynchronous clear and preset, LABCTRL1 controls the preset and LABCTRL2 controls the clear. DATA3 is tied to VCC, therefore, asserting LABCTRL1 asynchronously loads a one into the register, effectively presetting the register. Asserting LABCTRL2 clears the register. Asynchronous Load with Clear When implementing an asynchronous load in conjunction with the clear, LABCTRL1 implements the asynchronous load of DATA3 by controlling the register preset and clear. LABCTRL2 implements the clear by controlling the register clear; LABCTRL2 does not have to feed the preset circuits. Asynchronous Load with Preset When implementing an asynchronous load in conjunction with preset, the Altera software provides preset control by using the clear and inverting the input and output of the register. Asserting LABCTRL2 presets the register, while asserting LABCTRL1 loads the register. The Altera software inverts the signal that drives DATA3 to account for the inversion of the register's output. Asynchronous Load without Preset or Clear When implementing an asynchronous load without preset or clear, LABCTRL1 implements the asynchronous load of DATA3 by controlling the register preset and clear. FastTrack Interconnect In the FLEX 10K architecture, connections between LEs and device I/O pins are provided by the FastTrack Interconnect, which is a series of continuous horizontal and vertical routing channels that traverse the device. This global routing structure provides predictable performance, even in complex designs. In contrast, the segmented routing in FPGAs requires switch matrices to connect a variable number of routing paths, increasing the delays between logic resources and reducing performance. 24 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet The FastTrack Interconnect consists of row and column interconnect channels that span the entire device. Each row of LABs is served by a dedicated row interconnect. The row interconnect can drive I/O pins and feed other LABs in the device. The column interconnect routes signals between rows and can drive I/O pins. A row channel can be driven by an LE or by one of three column channels. These four signals feed dual 4-to-1 multiplexers that connect to two specific row channels. These multiplexers, which are connected to each LE, allow column channels to drive row channels even when all eight LEs in an LAB drive the row interconnect. Each column of LABs is served by a dedicated column interconnect. The column interconnect can then drive I/O pins or another row's interconnect to route the signals to other LABs in the device. A signal from the column interconnect, which can be either the output of an LE or an input from an I/O pin, must be routed to the row interconnect before it can enter an LAB or EAB. Each row channel that is driven by an IOE or EAB can drive one specific column channel. Access to row and column channels can be switched between LEs in adjacent pairs of LABs. For example, an LE in one LAB can drive the row and column channels normally driven by a particular LE in the adjacent LAB in the same row, and vice versa. This routing flexibility enables routing resources to be used more efficiently. See Figure 11. Altera Corporation 25 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 11. LAB Connections to Row & Column Interconnect Column Channels To Other Columns Row Channels At each intersection, four row channels can drive column channels. Each LE can drive two row channels. From Adjacent LAB To Adjacent LAB LE 1 Each LE can switch interconnect access with an LE in the adjacent LAB. LE 2 LE 8 To LAB Local Interconnect 26 To Other Rows Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet For improved routing, the row interconnect is comprised of a combination of full-length and half-length channels. The full-length channels connect to all LABs in a row; the half-length channels connect to the LABs in half of the row. The EAB can be driven by the half-length channels in the left half of the row and by the full-length channels. The EAB drives out to the full-length channels. In addition to providing a predictable, row-wide interconnect, this architecture provides increased routing resources. Two neighboring LABs can be connected using a half-row channel, thereby saving the other half of the channel for the other half of the row. Table 7 summarizes the FastTrack Interconnect resources available in each FLEX 10K device. Table 7. FLEX 10K FastTrack Interconnect Resources Device Rows Channels per Row Columns Channels per Column EPF10K10 EPF10K10A 3 144 24 24 EPF10K20 6 144 24 24 EPF10K30 EPF10K30A 6 216 36 24 EPF10K40 EPF10K50 EPF10K50V EPF10K70 8 216 36 24 10 216 36 24 9 312 52 24 EPF10K100 EPF10K100A 12 312 52 24 EPF10K130V 16 312 52 32 EPF10K250A 20 456 76 40 In addition to general-purpose I/O pins, FLEX 10K devices have six dedicated input pins that provide low-skew signal distribution across the device. These six inputs can be used for global clock, clear, preset, and peripheral output enable and clock enable control signals. These signals are available as control signals for all LABs and IOEs in the device. The dedicated inputs can also be used as general-purpose data inputs because they can feed the local interconnect of each LAB in the device. However, the use of dedicated inputs as data inputs can introduce additional delay into the control signal network. Altera Corporation 27 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 12 shows the interconnection of adjacent LABs and EABs with row, column, and local interconnects, as well as the associated cascade and carry chains. Each LAB is labeled according to its location: a letter represents the row and a number represents the column. For example, LAB B3 is in row B, column 3. Figure 12. Interconnect Resources See Figure 15 for details. I/O Element (IOE) IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE Row Interconnect LAB A1 LAB A2 See Figure 14 for details. LAB A3 Column Interconnect To LAB A5 To LAB A4 IOE IOE IOE IOE LAB B1 LAB B2 Cascade & Carry Chains LAB B3 To LAB B5 To LAB B4 IOE 28 IOE IOE IOE IOE IOE Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet I/O Element An I/O element (IOE) contains a bidirectional I/O buffer and a register that can be used either as an input register for external data that requires a fast setup time, or as an output register for data that requires fast clockto-output performance. In some cases, using an LE register for an input register will result in a faster setup time than using an IOE register. IOEs can be used as input, output, or bidirectional pins. For bidirectional registered I/O implementation, the output register should be in the IOE and, the data input and output enable register should be LE registers placed adjacent to the bidirectional pin. The Compiler uses the programmable inversion option to invert signals from the row and column interconnect automatically where appropriate. Figure 13 shows the bidirectional I/O registers. Altera Corporation 29 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 13. Bidirectional I/O Registers Row and Column Interconnect 2 Dedicated Clock Inputs 4 Dedicated Inputs Peripheral Control Bus 2 4 OE Register 12 D Q ENA CLRN VCC Chip-Wide Reset VCC Chip-Wide Output Enable OE[7..0] VCC Output Register D Q CLK[1..0] ENA CLRN CLK[3..2] VCC Open-Drain Output Slew-Rate Control ENA[5..0] VCC CLRN[1..0] Chip-Wide Reset Input Register D Q VCC ENA CLRN Chip-Wide Reset 30 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Each IOE selects the clock, clear, clock enable, and output enable controls from a network of I/O control signals called the peripheral control bus. The peripheral control bus uses high-speed drivers to minimize signal skew across devices; it provides up to 12 peripheral control signals that can be allocated as follows: Up to eight output enable signals Up to six clock enable signals Up to two clock signals Up to two clear signals If more than six clock enable or eight output enable signals are required, each IOE on the device can be controlled by clock enable and output enable signals driven by specific LEs. In addition to the two clock signals available on the peripheral control bus, each IOE can use one of two dedicated clock pins. Each peripheral control signal can be driven by any of the dedicated input pins or the first LE of each LAB in a particular row. In addition, an LE in a different row can drive a column interconnect, which causes a row interconnect to drive the peripheral control signal. The chip-wide reset signal will reset all IOE registers, overriding any other control signals. Tables 8 and 9 list the sources for each peripheral control signal, and the rows that can drive global signals. These tables also show how the output enable, clock enable, clock, and clear signals share 12 peripheral control signals. Altera Corporation 31 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 8. EPF10K10, EPF10K20, EPF10K30, EPF10K40 & EPF10K50 Peripheral Bus Sources Peripheral Control Signal EPF10K10 EPF10K10A EPF10K20 EPF10K30 EPF10K30A EPF10K40 EPF10K50 EPF10K50V OE0 Row A Row A Row A Row A Row A OE1 Row A Row B Row B Row C Row B OE2 Row B Row C Row C Row D Row D OE3 Row B Row D Row D Row E Row F OE4 Row C Row E Row E Row F Row H OE5 Row C Row F Row F Row G Row J CLKENA0/CLK0/GLOBAL0 Row A Row A Row A Row B Row A CLKENA1/OE6/GLOBAL1 Row A Row B Row B Row C Row C CLKENA2/CLR0 Row B Row C Row C Row D Row E CLKENA3/OE7/GLOBAL2 Row B Row D Row D Row E Row G CLKENA4/CLR1 Row C Row E Row E Row F Row I CLKENA5/CLK1/GLOBAL3 Row C Row F Row F Row H Row J Table 9. EPF10K70, EPF10K100, EPF10K130V & EPF10K250A Peripheral Bus Sources Peripheral Control Signal 32 EPF10K70 EPF10K100 EPF10K100A EPF10K130V EPF10K250A OE0 Row A Row A Row C Row E OE1 Row B Row C Row E Row G OE2 Row D Row E Row G Row I OE3 Row I Row L Row N Row P OE4 Row G Row I Row K Row M OE5 Row H Row K Row M Row O CLKENA0/CLK0/GLOBAL0 Row E Row F Row H Row J CLKENA1/OE6/GLOBAL1 Row C Row D Row F Row H CLKENA2/CLR0 Row B Row B Row D Row F CLKENA3/OE7/GLOBAL2 Row F Row H Row J Row L CLKENA4/CLR1 Row H Row J Row L Row N CLKENA5/CLK1/GLOBAL3 Row E Row G Row I Row K Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Signals on the peripheral control bus can also drive the four global signals, referred to as GLOBAL0 through GLOBAL3 in Tables 8 and 9. The internally generated signal can drive the global signal, providing the same low-skew, low-delay characteristics for an internally generated signal as for a signal driven by an input. This feature is ideal for internally generated clear or clock signals with high fan-out. When a global signal is driven by internal logic, the dedicated input pin that drives that global signal cannot be used. The dedicated input pin should be driven to a known logic state (such as ground) and not be allowed to float. When the chip-wide output enable pin is held low, it will tri-state all pins on the device. This option can be set in the Global Project Device Options menu. Additionally, the registers in the IOE can be reset by holding the chip-wide reset pin low. Row-to-IOE Connections When an IOE is used as an input signal, it can drive two separate row channels. The signal is accessible by all LEs within that row. When an IOE is used as an output, the signal is driven by a multiplexer that selects a signal from the row channels. Up to eight IOEs connect to each side of each row channel. See Figure 14. Figure 14. FLEX 10K Row-to-IOE Connections The values for m and n are provided in Table 10. IOE1 m Row FastTrack Interconnect n n n IOE8 m Each IOE is driven by an m-to-1 multiplexer. Each IOE can drive up to two row channels. Altera Corporation 33 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 10 lists the FLEX 10K row-to-IOE interconnect resources. Table 10. FLEX 10K Row-to-IOE Interconnect Resources Device Channels per Row (n) Row Channels per Pin (m) EPF10K10 EPF10K10A 144 18 EPF10K20 144 18 EPF10K30 EPF10K30A 216 27 EPF10K40 216 27 EPF10K50 EPF10K50V 216 27 EPF10K70 312 39 EPF10K100 EPF10K100A 312 39 EPF10K130V 312 39 EPF10K250A 456 57 Column-to-IOE Connections When an IOE is used as an input, it can drive up to two separate column channels. When an IOE is used as an output, the signal is driven by a multiplexer that selects a signal from the column channels. Two IOEs connect to each side of the column channels. Each IOE can be driven by column channels via a multiplexer. The set of column channels that each IOE can access is different for each IOE. See Figure 15. 34 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 15. FLEX 10K Column-to-IOE Connections The values for m and n are provided in Table 11. Each IOE is driven by an m-to-1 multiplexer. Column Interconnect m IOE1 m IOE1 n n n Each IOE can drive up to two column channels. Table 11 lists the FLEX 10K column-to-IOE interconnect resources. Table 11. FLEX 10K Column-to-IOE Interconnect Resources Altera Corporation Device Channels per Column (n) Column Channel per Pin (m) EPF10K10 EPF10K10A 24 16 EPF10K20 24 16 EPF10K30 EPF10K30A 24 16 EPF10K40 24 16 EPF10K50 EPF10K50V 24 16 EPF10K70 24 16 EPF10K100 EPF10K100A 24 16 EPF10K130V 32 24 EPF10K250A 40 32 35 FLEX 10K Embedded Programmable Logic Device Family Data Sheet SameFrame Pin-Outs FLEX 10KE devices support the SameFrame pin-out feature for FineLine BGA packages. The SameFrame pin-out feature is the arrangement of balls on FineLine BGA packages such that the lower-ballcount packages form a subset of the higher-ball-count packages. SameFrame pin-outs provide the flexibility to migrate not only from device to device within the same package, but also from one package to another. A given printed circuit board (PCB) layout can support multiple device density/package combinations. For example, a single board layout can support a range of devices from an EPF10K10A device in a 256-pin FineLine BGA package to an EPF10K100A device in a 484-pin FineLine BGA package. The Altera software provides support to design PCBs with SameFrame pin-out devices. Devices can be defined for present and future use. The Altera software generates pin-outs describing how to lay out a board to take advantage of this migration (see Figure 16). Figure 16. SameFrame Pin-Out Example Printed Circuit Board Designed for 484-PinFineLine BGA Package 256-Pin FineLine BGA 256-Pin FineLine BGA Package (Reduced I/O Count or Logic Requirements) 36 484-Pin FineLine BGA 484-Pin FineLine BGA Package (Increased I/O Count or Logic Requirements) Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet ClockLock & ClockBoost Features To support high-speed designs, selected FLEX 10K devices offer optional ClockLock and ClockBoost circuitry containing a phase-locked loop (PLL) that is used to increase design speed and reduce resource usage. The ClockLock circuitry uses a synchronizing PLL that reduces the clock delay and skew within a device. This reduction minimizes clock-to-output and setup times while maintaining zero hold times. The ClockBoost circuitry, which provides a clock multiplier, allows the designer to enhance device area efficiency by sharing resources within the device. The ClockBoost feature allows the designer to distribute a low-speed clock and multiply that clock on-device. Combined, the ClockLock and ClockBoost features provide significant improvements in system performance and bandwidth. The ClockLock and ClockBoost features in FLEX 10K devices are enabled through the Altera software. External devices are not required to use these features. The output of the ClockLock and ClockBoost circuits is not available at any of the device pins. The ClockLock and ClockBoost circuitry locks onto the rising edge of the incoming clock. The circuit output can only drive the clock inputs of registers; the generated clock cannot be gated or inverted. The dedicated clock pin (GCLK1) supplies the clock to the ClockLock and ClockBoost circuitry. When the dedicated clock pin is driving the ClockLock or ClockBoost circuitry, it cannot drive elsewhere in the device. In designs that require both a multiplied and non-multiplied clock, the clock trace on the board can be connected to GCLK1. With the Altera software, GCLK1 can feed both the ClockLock and ClockBoost circuitry in the FLEX 10K device. However, when both circuits are used, the other clock pin (GCLK0) cannot be used. Figure 17 shows a block diagram of how to enable both the ClockLock and ClockBoost circuits in the Altera software. The example shown is a schematic, but a similar approach applies for designs created in AHDL, VHDL, and Verilog HDL. When the ClockLock and ClockBoost circuits are used simultaneously, the input frequency parameter must be the same for both circuits. In Figure 17, the input frequency must meet the requirements specified when the ClockBoost multiplication factor is two. Altera Corporation 37 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 17. Enabling ClockLock & ClockBoost in the Same Design CLOCKBOOST=1 INPUT_FREQUENCY=50 CLKLOCK a D Q aout D Q bout gclk1 CLOCKBOOST=2 INPUT_FREQUENCY=50 CLKLOCK b To use both the ClockLock and ClockBoost circuits in the same design, designers must use Revision C EPF10K100GC503-3DX devices and MAX+PLUS II software versions 7.2 or higher. The die revision is indicated by the third digit of the nine-digit code on the top side of the device. Output Configuration This section discusses the peripheral component interconnect (PCI) pull-up clamping diode option, slew-rate control, open-drain output option, MultiVolt I/O interface, and power sequencing for FLEX 10K devices. The PCI pull-up clamping diode, slew-rate control, and open-drain output options are controlled pin-by-pin via Altera logic options. The MultiVolt I/O interface is controlled by connecting VCCIO to a different voltage than VCCINT. Its effect can be simulated in the Altera software via the Global Project Device Options dialog box (Assign menu). PCI Clamping Diodes The EPF10K10A and EPF10K30A devices have a pull-up clamping diode on every I/O, dedicated input, and dedicated clock pin. PCI clamping diodes clamp the transient overshoot caused by reflected waves to the VCCIO value and are required for 3.3-V PCI compliance. Clamping diodes can also be used to limit overshoot in other systems. Clamping diodes are controlled on a pin-by-pin basis via a logic option in the Altera software. When VCCIO is 3.3 V, a pin that has the clamping diode turned on can be driven by a 2.5-V or 3.3-V signal, but not a 5.0-V signal. When VCCIO is 2.5 V, a pin that has the clamping diode turned on can be driven by a 2.5-V signal, but not a 3.3-V or 5.0-V signal. However, a clamping diode can be turned on for a subset of pins, which allows devices to bridge between a 3.3-V PCI bus and a 5.0-V device. 38 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Slew-Rate Control The output buffer in each IOE has an adjustable output slew rate that can be configured for low-noise or high-speed performance. A slower slew rate reduces system noise and adds a maximum delay of approximately 2.9 ns. The fast slew rate should be used for speed-critical outputs in systems that are adequately protected against noise. Designers can specify the slew rate on a pin-by-pin basis during design entry or assign a default slew rate to all pins on a device-wide basis. The slow slew rate setting affects only the falling edge of the output. Open-Drain Output Option FLEX 10K devices provide an optional open-drain (electrically equivalent to an open-collector) output for each I/O pin. This open-drain output enables the device to provide system-level control signals (e.g., interrupt and write enable signals) that can be asserted by any of several devices. It can also provide an additional wired-OR plane. Additionally, the Altera software can convert tri-state buffers with grounded data inputs to opendrain pins automatically. Open-drain output pins on FLEX 10K devices (with a pull-up resistor to the 5.0-V supply) can drive 5.0-V CMOS input pins that require a VIH of 3.5 V. When the open-drain pin is active, it will drive low. When the pin is inactive, the trace will be pulled up to 5.0 V by the resistor. The opendrain pin will only drive low or tri-state; it will never drive high. The rise time is dependent on the value of the pull-up resistor and load impedance. The IOL current specification should be considered when selecting a pull-up resistor. Output pins on 5.0-V FLEX 10K devices with VCCIO = 3.3 V or 5.0 V (with a pull-up resistor to the 5.0-V supply) can also drive 5.0-V CMOS input pins. In this case, the pull-up transistor will turn off when the pin voltage exceeds 3.3 V. Therefore, the pin does not have to be open-drain. MultiVolt I/O Interface The FLEX 10K device architecture supports the MultiVolt I/O interface feature, which allows FLEX 10K devices to interface with systems of differing supply voltages. These devices have one set of VCC pins for internal operation and input buffers (VCCINT) and another set for I/O output drivers (VCCIO). Altera Corporation 39 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 12 describes the FLEX 10K device supply voltages and MultiVolt I/O support levels. Table 12. Supply Voltages & MultiVolt I/O Support Levels Devices Supply Voltage (V) VCCINT FLEX 10K (1) VCCIO MultiVolt I/O Support Levels (V) Input Output 5.0 5.0 3.3 or 5.0 5.0 5.0 3.3 3.3 or 5.0 3.3 or 5.0 EPF10K50V (1) 3.3 3.3 3.3 or 5.0 3.3 or 5.0 EPF10K130V 3.3 3.3 3.3 or 5.0 3.3 or 5.0 FLEX 10KA (1) 3.3 3.3 2.5, 3.3, or 5.0 3.3 or 5.0 3.3 2.5 2.5, 3.3, or 5.0 2.5 Note (1) 240-pin QFP packages do not support the MultiVolt I/O features, so they do not have separate VCCIO pins. Power Sequencing & Hot-Socketing Because FLEX 10K devices can be used in a multi-voltage environment, they have been designed specifically to tolerate any possible power-up sequence. The VCCIO and VCCINT power supplies can be powered in any order. Signals can be driven into FLEX 10KA devices before and during power up without damaging the device. Additionally, FLEX 10KA devices do not drive out during power up. Once operating conditions are reached, FLEX 10KA devices operate as specified by the user. IEEE Std. 1149.1 (JTAG) Boundary-Scan Support 40 All FLEX 10K devices provide JTAG BST circuitry that complies with the IEEE Std. 1149.1-1990 specification. All FLEX 10K devices can also be configured using the JTAG pins through the BitBlaster serial download cable, or ByteBlasterMV parallel port download cable, or via hardware that uses the JamTM programming and test language. JTAG BST can be performed before or after configuration, but not during configuration. FLEX 10K devices support the JTAG instructions shown in Table 13. Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 13. FLEX 10K JTAG Instructions JTAG Instruction Description SAMPLE/PRELOAD Allows a snapshot of signals at the device pins to be captured and examined during normal device operation, and permits an initial data pattern output at the device pins. EXTEST Allows the external circuitry and board-level interconnections to be tested by forcing a test pattern at the output pins and capturing test results at the input pins. BYPASS Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST data to pass synchronously through a selected device to adjacent devices during normal device operation. USERCODE Selects the user electronic signature (USERCODE) register and places it between the TDI and TDO pins, allowing the USERCODE to be serially shifted out of TDO. IDCODE Selects the IDCODE register and places it between TDI and TDO, allowing the IDCODE to be serially shifted out of TDO. ICR Instructions These instructions are used when configuring a FLEX 10K device via JTAG ports with a BitBlaster, or ByteBlasterMV or MasterBlaster download cable, or using a Jam File (.jam) or Jam Byte-Code File (.jbc) via an embedded processor. The instruction register length of FLEX 10K devices is 10 bits. The USERCODE register length in FLEX 10K devices is 32 bits; 7 bits are determined by the user, and 25 bits are predetermined. Tables 14 and 15 show the boundary-scan register length and device IDCODE information for FLEX 10K devices. Table 14. FLEX 10K Boundary-Scan Register Length Device EPF10K10, EPF10K10A Altera Corporation Boundary-Scan Register Length 480 EPF10K20 624 EPF10K30, EPF10K30A 768 EPF10K40 864 EPF10K50, EPF10K50V 960 EPF10K70 1,104 EPF10K100, EPF10K100A 1,248 EPF10K130V 1,440 EPF10K250A 1,440 41 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 15. 32-Bit FLEX 10K Device IDCODE Note (1) Device IDCODE (32 Bits) Version (4 Bits) Part Number (16 Bits) Manufacturer's Identity 1 (1 Bit) (11 Bits) (2) EPF10K10, EPF10K10A 0000 0001 0000 0001 0000 00001101110 1 EPF10K20 0000 0001 0000 0010 0000 00001101110 1 EPF10K30, EPF10K30A 0000 0001 0000 0011 0000 00001101110 1 EPF10K40 0000 0001 0000 0100 0000 00001101110 1 EPF10K50, EPF10K50V 0000 0001 0000 0101 0000 00001101110 1 EPF10K70 0000 0001 0000 0111 0000 00001101110 1 EPF10K100, EPF10K100A 0000 0000 0001 0000 0000 00001101110 1 EPF10K130V 0000 0000 0001 0011 0000 00001101110 1 EPF10K250A 0000 0000 0010 0101 0000 00001101110 1 Notes: (1) (2) The most significant bit (MSB) is on the left. The least significant bit (LSB) for all JTAG IDCODEs is 1. FLEX 10K devices include weak pull-ups on JTAG pins. f For more information, see the following documents: 42 Application Note 39 (IEEE 1149.1 (JTAG) Boundary-Scan Testing in Altera Devices) BitBlaster Serial Download Cable Data Sheet ByteBlasterMV Parallel Port Download Cable Data Sheet Jam Programming & Test Language Specification Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 18 shows the timing requirements for the JTAG signals. Figure 18. JTAG Waveforms TMS TDI t JCP t JCH t JCL t JPSU t JPH TCK tJPZX t JPXZ t JPCO TDO tJSH tJSSU Signal to Be Captured Signal to Be Driven tJSCO tJSZX tJSXZ Table 16 shows the timing parameters and values for FLEX 10K devices. Table 16. JTAG Timing Parameters & Values Symbol Altera Corporation Parameter Min Max Unit tJCP TCK clock period 100 ns tJCH TCK clock high time 50 ns tJCL TCK clock low time 50 ns tJPSU JTAG port setup time 20 ns tJPH JTAG port hold time 45 ns tJPCO JTAG port clock to output 25 ns tJPZX JTAG port high impedance to valid output 25 ns tJPXZ JTAG port valid output to high impedance 25 ns tJSSU Capture register setup time 20 tJSH Capture register hold time 45 tJSCO Update register clock to output 35 ns tJSZX Update register high-impedance to valid output 35 ns tJSXZ Update register valid output to high impedance 35 ns ns ns 43 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Generic Testing Each FLEX 10K device is functionally tested. Complete testing of each configurable SRAM bit and all logic functionality ensures 100% yield. AC test measurements for FLEX 10K devices are made under conditions equivalent to those shown in Figure 19. Multiple test patterns can be used to configure devices during all stages of the production flow. Figure 19. FLEX 10K AC Test Conditions Power supply transients can affect AC measurements. Simultaneous transitions of multiple outputs should be avoided for accurate measurement. Threshold tests must not be performed under AC conditions. Large-amplitude, fast-ground-current transients normally occur as the device outputs discharge the load capacitances. When these transients flow through the parasitic inductance between the device ground pin and the test system ground, significant reductions in observable noise immunity can result. Numbers without parentheses are for 5.0-V devices or outputs. Numbers in parentheses are for 3.3-V devices or outputs. Numbers in brackets are for 2.5-V devices or outputs. Operating Conditions To Test System Device Output 250 (8.06 k) [481 ] C1 (includes JIG capacitance) Device input rise and fall times < 3 ns Tables 17 through 21 provide information on absolute maximum ratings, recommended operating conditions, DC operating conditions, and capacitance for 5.0-V FLEX 10K devices. Table 17. FLEX 10K 5.0-V Device Absolute Maximum Ratings Symbol VCC 464 (703 ) [521 ] Parameter Note (1) Conditions V CC Supply voltage VI DC input voltage I OUT DC output current, per pin T STG Storage temperature No bias T AMB Ambient temperature Under bias -65 TJ Junction temperature 44 With respect to ground (2) Min Max Unit -2.0 7.0 V -2.0 7.0 V -25 25 mA -65 150 C 135 C Ceramic packages, under bias 150 C PQFP, TQFP, RQFP, and BGA packages, under bias 135 C Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 18. FLEX 10K 5.0-V Device Recommended Operating Conditions Symbol Parameter Conditions Min Max Unit V CCINT Supply voltage for internal logic (3), (4) and input buffers 4.75 (4.50) 5.25 (5.50) V V CCIO Supply voltage for output buffers, 5.0-V operation (3), (4) 4.75 (4.50) 5.25 (5.50) V Supply voltage for output buffers, 3.3-V operation (3), (4) 3.00 (3.00) 3.60 (3.60) V -0.5 V CCINT + 0.5 V 0 V CCIO V 0 70 C VI Input voltage VO Output voltage TA Ambient temperature For commercial use TJ Operating temperature For commercial use For industrial use For industrial use -40 85 C 0 85 C -40 100 C tR Input rise time 40 ns tF Input fall time 40 ns Altera Corporation 45 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 19. FLEX 10K 5.0-V Device DC Operating Conditions Symbol Parameter Notes (5), (6) Conditions Min Typ Max Unit 2.0 V CCINT + 0.5 V -0.5 0.8 V V IH High-level input voltage V IL Low-level input voltage V OH 5.0-V high-level TTL output voltage I OH = -4 mA DC, V CCIO = 4.75 V (7) 2.4 V 3.3-V high-level TTL output voltage I OH = -4 mA DC, V CCIO = 3.00 V (7) 2.4 V V CCIO - 0.2 V 3.3-V high-level CMOS I OH = -0.1 mA DC, V CCIO = 3.00 V (7) output voltage V OL 5.0-V low-level TTL output voltage I OL = 12 mA DC, V CCIO = 4.75 V (8) 0.45 V 3.3-V low-level TTL output voltage I OL = 12 mA DC, V CCIO = 3.00 V (8) 0.45 V 3.3-V low-level CMOS I OL = 0.1 mA DC, V CCIO = 3.00 V output voltage (8) 0.2 V II Input pin leakage current V I = V CC or ground (9) -10 10 A I OZ Tri-stated I/O pin leakage current V O = V CC or ground (9) -40 40 A I CC0 V CC supply current (standby) V I = ground, no load 10 mA 0.5 Table 20. 5.0-V Device Capacitance of EPF10K10, EPF10K20 & EPF10K30 Devices Symbol Parameter Conditions Min Note (10) Max Unit CIN Input capacitance VIN = 0 V, f = 1.0 MHz 8 pF CINCLK Input capacitance on dedicated VIN = 0 V, f = 1.0 MHz clock pin 12 pF COUT Output capacitance 8 pF VOUT = 0 V, f = 1.0 MHz Table 21. 5.0-V Device Capacitance of EPF10K40, EPF10K50, EPF10K70 & EPF10K100 Devices Symbol Parameter Conditions Min Note (10) Max Unit CIN Input capacitance VIN = 0 V, f = 1.0 MHz 10 pF CINCLK Input capacitance on dedicated VIN = 0 V, f = 1.0 MHz clock pin 15 pF COUT Output capacitance 10 pF 46 VOUT = 0 V, f = 1.0 MHz Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) See the Operating Requirements for Altera Devices Data Sheet. Minimum DC input voltage is -0.5 V. During transitions, the inputs may undershoot to -2.0 V for input currents less than 100 mA and periods shorter than 20 ns. (3) Numbers in parentheses are for industrial-temperature-range devices. (4) Maximum VCC rise time is 100 ms. VCC must rise monotonically. (5) Typical values are for T A = 25 C and V CC = 5.0 V. (6) These values are specified under the Recommended Operation Condition shown in Table 18 on page 45. (7) The IOH parameter refers to high-level TTL or CMOS output current. (8) The IOL parameter refers to low-level TTL or CMOS output current. This parameter applies to open-drain pins as well as output pins. (9) This value is specified for normal device operation. The value may vary during power-up. (10) Capacitance is sample-tested only. Figure 20 shows the typical output drive characteristics of FLEX 10K devices with 5.0-V and 3.3-V VCCIO. The output driver is compliant with the 5.0-V PCI Local Bus Specification, Revision 2.2 (for 5.0-V VCCIO). Figure 20. Output Drive Characteristics of FLEX 10K Devices 5.0-V 3.3-V 150 120 Typical IO Output Current (mA) 150 IOL 120 VCCINT = 5.0 V VCCIO = 5.0 V Room Temperature 90 Typical IO Output Current (mA) VCCINT = 5.0 V VCCIO = 3.3 V Room Temperature 90 60 60 IOH IOH 45 30 30 1 2 3 4 VO Output Voltage (V) Altera Corporation IOL 5 1 2 3 3.3 4 5 VO Output Voltage (V) 47 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Tables 22 through 25 provide information on absolute maximum ratings, recommended operating conditions, DC operating conditions, and capacitance for EPF10K50V and EPF10K130V devices. Table 22. EPF10K50V & EPF10K130V Device Absolute Maximum Ratings Symbol Parameter V CC Supply voltage Conditions With respect to ground (2) Note (1) Min Max Unit -0.5 4.6 V VI DC input voltage -2.0 5.75 V I OUT DC output current, per pin -25 25 mA T STG Storage temperature No bias -65 150 C T AMB Ambient temperature Under bias -65 135 C TJ Junction temperature Ceramic packages, under bias 150 C RQFP and BGA packages, under bias 135 C Min Max Unit V CCINT Supply voltage for internal logic (3), (4) and input buffers 3.00 (3.00) 3.60 (3.60) V V CCIO Supply voltage for output buffers (3), (4) 3.00 (3.00) 3.60 (3.60) V VI Input voltage (5) -0.5 5.75 V VO Output voltage 0 V CCIO V TA Ambient temperature 0 70 C -40 85 C 0 85 C -40 100 C Table 23. EPF10K50V & EPF10K130V Device Recommended Operating Conditions Symbol Parameter Conditions For commercial use For industrial use TJ Operating temperature For commercial use For industrial use tR Input rise time 40 ns tF Input fall time 40 ns 48 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 24. EPF10K50V & EPF10K130V Device DC Operating Conditions Symbol Parameter Conditions Notes (6), (7) Min Typ Max Unit 2.0 5.75 V -0.5 0.8 V V IH High-level input voltage V IL Low-level input voltage V OH 3.3-V high-level TTL output voltage I OH = -8 mA DC (8) 3.3-V high-level CMOS output voltage I OH = -0.1 mA DC (8) 3.3-V low-level TTL output voltage I OL = 8 mA DC (9) 0.45 V 3.3-V low-level CMOS output voltage I OL = 0.1 mA DC (9) 0.2 V V OL 2.4 V V CCIO - 0.2 V II Input pin leakage current V I = 5.3 V to -0.3 V (10) -10 10 A I OZ Tri-stated I/O pin leakage current V O = 5.3 V to -0.3 V (10) -10 10 A I CC0 V CC supply current (standby) V I = ground, no load 0.3 10 mA V I = ground, no load (11) 10 Table 25. EPF10K50V & EPF10K130V Device Capacitance Parameter Symbol mA (12) Conditions Min Max Unit CIN Input capacitance VIN = 0 V, f = 1.0 MHz 10 pF CINCLK Input capacitance on dedicated VIN = 0 V, f = 1.0 MHz clock pin 15 pF COUT Output capacitance 10 pF VOUT = 0 V, f = 1.0 MHz Notes to tables: (1) (2) See the Operating Requirements for Altera Devices Data Sheet. Minimum DC input voltage is -0.5 V. During transitions, the inputs may undershoot to -2.0 V or overshoot to 5.75 V for input currents less than 100 mA and periods shorter than 20 ns. (3) Numbers in parentheses are for industrial-temperature-range devices. (4) Maximum VCC rise time is 100 ms. VCC must rise monotonically. (5) EPF10K50V and EPF10K130V device inputs may be driven before VCCINT and VCCIO are powered. (6) Typical values are for T A = 25 C and V CC = 3.3 V. (7) These values are specified under the EPF10K50V and EPF10K130V device Recommended Operating Conditions in Table 23 on page 48. (8) The IOH parameter refers to high-level TTL or CMOS output current. (9) The IOL parameter refers to low-level TTL or CMOS output current. This parameter applies to open-drain pins as well as output pins. (10) This value is specified for normal device operation. The value may vary during power-up. (11) This parameter applies to -1 speed grade EPF10K50V devices, -2 speed grade EPF10K50V industrial temperature devices, and -2 speed grade EPF10K130V devices. (12) Capacitance is sample-tested only. Altera Corporation 49 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 21 shows the typical output drive characteristics of EPF10K50V and EPF10K130V devices. Figure 21. Output Drive Characteristics of EPF10K50V & EPF10K130V Devices 60 Typical IO Output Current (mA) 40 IOL Vcc = 3.3 V Room Temperature 20 IOH 1 2 3 VO Output Voltage (V) Tables 26 through 31 provide information on absolute maximum ratings, recommended operating conditions, DC operating conditions, and capacitance for 3.3-V FLEX 10K devices. Table 26. FLEX 10KA 3.3-V Device Absolute Maximum Ratings Symbol Parameter Note (1) Conditions V CC Supply voltage VI DC input voltage I OUT DC output current, per pin T STG Storage temperature No bias T AMB Ambient temperature Under bias -65 TJ Junction temperature 50 With respect to ground (2) Min Max Unit -0.5 4.6 V -2.0 5.75 V -25 25 mA -65 150 C 135 C Ceramic packages, under bias 150 C PQFP, TQFP, RQFP, and BGA packages, under bias 135 C Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 27. FLEX 10KA 3.3-V Device Recommended Operating Conditions Symbol Parameter Conditions Min Max Unit V CCINT Supply voltage for internal logic (3), (4) and input buffers 3.00 (3.00) 3.60 (3.60) V V CCIO Supply voltage for output buffers, 3.3-V operation (3), (4) 3.00 (3.00) 3.60 (3.60) V Supply voltage for output buffers, 2.5-V operation (3), (4) 2.30 (2.30) 2.70 (2.70) V VI Input voltage (5) -0.5 5.75 V VO Output voltage 0 V CCIO V TA Ambient temperature For commercial use 0 70 C TJ Operating temperature For commercial use For industrial use For industrial use -40 85 C 0 85 C -40 100 C tR Input rise time 40 ns tF Input fall time 40 ns Altera Corporation 51 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 28. FLEX 10KA 3.3-V Device DC Operating Conditions Symbol Parameter V IH High-level input voltage V IL Low-level input voltage V OH 3.3-V high-level TTL output voltage V OL Conditions I OH = -11 mA DC, V CCIO = 3.00 V (8) Notes (6), (7) Min Typ Max Unit 1.7 or 0.5 x V CCINT, whichever is lower 5.75 V -0.5 0.3 x VCCINT V 2.4 V 3.3-V high-level CMOS output I OH = -0.1 mA DC, V CCIO = 3.00 V (8) voltage V CCIO - 0.2 V 3.3-V high-level PCI output voltage 0.9 x VCCIO V 2.5-V high-level output voltage I OH = -0.1 mA DC, V CCIO = 2.30 V (8) 2.1 V I OH = -1 mA DC, V CCIO = 2.30 V (8) 2.0 V I OH = -2 mA DC, V CCIO = 2.30 V (8) 1.7 V I OH = -0.5 mA DC, V CCIO = 3.00 to 3.60 V (8) 3.3-V low-level TTL output voltage I OL = 9 mA DC, V CCIO = 3.00 V (9) 0.45 V 3.3-V low-level CMOS output voltage I OL = 0.1 mA DC, V CCIO = 3.00 V (9) 0.2 V 3.3-V low-level PCI output voltage I OL = 1.5 mA DC, V CCIO = 3.00 to 3.60 V (9) 0.1 x VCCIO V 2.5-V low-level output voltage I OL = 0.1 mA DC, V CCIO = 2.30 V (9) 0.2 V I OL = 1 mA DC, V CCIO = 2.30 V (9) 0.4 V I OL = 2 mA DC, V CCIO = 2.30 V (9) 0.7 V II Input pin leakage current V I = 5.3 V to -0.3 V (10) -10 10 A I OZ Tri-stated I/O pin leakage current V O = 5.3 V to -0.3 V (10) -10 10 A I CC0 V CC supply current (standby) V I = ground, no load 0.3 10 mA V I = ground, no load (11) 10 52 mA Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 29. 3.3-V Device Capacitance of EPF10K10A & EPF10K30A Devices Parameter Symbol Conditions Note (12) Min Max Unit CIN Input capacitance VIN = 0 V, f = 1.0 MHz 8 pF CINCLK Input capacitance on dedicated VIN = 0 V, f = 1.0 MHz clock pin 12 pF COUT Output capacitance 8 pF VOUT = 0 V, f = 1.0 MHz Table 30. 3.3-V Device Capacitance of EPF10K100A Devices Parameter Symbol Note (12) Conditions Min Max Unit CIN Input capacitance VIN = 0 V, f = 1.0 MHz 10 pF CINCLK Input capacitance on dedicated VIN = 0 V, f = 1.0 MHz clock pin 15 pF COUT Output capacitance 10 pF Max Unit VOUT = 0 V, f = 1.0 MHz Table 31. 3.3-V Device Capacitance of EPF10K250A Devices Parameter Symbol Conditions Note (12) Min CIN Input capacitance VIN = 0 V, f = 1.0 MHz 10 pF CINCLK Input capacitance on dedicated VIN = 0 V, f = 1.0 MHz clock pin 15 pF COUT Output capacitance 10 pF VOUT = 0 V, f = 1.0 MHz Notes to tables: (1) (2) See the Operating Requirements for Altera Devices Data Sheet. Minimum DC voltage input is -0.5 V. During transitions, the inputs may undershoot to -2.0 V or overshoot to 5.75 V for input currents less than 100 mA and periods shorter than 20 ns. (3) Numbers in parentheses are for industrial-temperature-range devices. (4) Maximum VCC rise time is 100 ms, and VCC must rise monotonically. (5) FLEX 10KA device inputs may be driven before VCCINT and VCCIO are powered. (6) Typical values are for T A = 25 C and V CC = 3.3 V. (7) These values are specified under the Recommended Operating Conditions shown in Table 27 on page 51. (8) The IOH parameter refers to high-level TTL, PCI, or CMOS output current. (9) The IOL parameter refers to low-level TTL, PCI, or CMOS output current. This parameter applies to open-drain pins as well as output pins. (10) This value is specified for normal device operation. The value may vary during power-up. (11) This parameter applies to all -1 speed grade commercial temperature devices and all -2 speed grade industrial-temperature devices. (12) Capacitance is sample-tested only. Altera Corporation 53 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 22 shows the typical output drive characteristics of EPF10K10A, EPF10K30A, EPF10K100A, and EPF10K250A devices with 3.3-V and 2.5-V V CCIO. The output driver is compliant with the 3.3-V PCI Local Bus Specification, Revision 2.2 (with 3.3-V V CCIO). Moreover, device analysis shows that the EPF10K10A, EPF10K30A, and EPF 10K100A devices can drive a 5.0-V PCI bus with eight or fewer loads. Figure 22. Output Drive Characteristics for EPF10K10A, EPF10K30A & EPF10K100A Devices 60 60 IOL IOL 50 50 40 Typical IO Output Current (mA) VCCINT = 3.3 V VCCIO = 3.3 V Room Temperature 30 40 Typical IO Output Current (mA) VCCINT = 3.3 V VCCIO = 2.5 V Room Temperature 30 20 20 10 10 IOH 1 2 3 4 VO Output Voltage (V) IOH 1 2 3 4 VO Output Voltage (V) Figure 23 shows the typical output drive characteristics of the EPF10K250A device with 3.3-V and 2.5-V VCCIO. 54 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 23. Output Drive Characteristics for EPF10K250A Device 50 50 IOL IOL 40 40 Typical IO Output Current (mA) VCCINT = 3.3 V VCCIO = 3.3 V Room Temperature 30 Typical IO Output Current (mA) VCCINT = 3.3 V VCCIO = 2.5 V Room Temperature 30 20 20 IOH 10 10 IOH 1 2 3 4 VO Output Voltage (V) Timing Model 1 2 3 4 VO Output Voltage (V) The continuous, high-performance FastTrack Interconnect routing resources ensure predictable performance and accurate simulation and timing analysis. This predictable performance contrasts with that of FPGAs, which use a segmented connection scheme and therefore have unpredictable performance. Device performance can be estimated by following the signal path from a source, through the interconnect, to the destination. For example, the registered performance between two LEs on the same row can be calculated by adding the following parameters: LE register clock-to-output delay (tCO) Interconnect delay (tSAMEROW) LE look-up table delay (tLUT) LE register setup time (tSU) The routing delay depends on the placement of the source and destination LEs. A more complex registered path may involve multiple combinatorial LEs between the source and destination LEs. Altera Corporation 55 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Timing simulation and delay prediction are available with the MAX+PLUS II Simulator and Timing Analyzer, or with industrystandard EDA tools. The Simulator offers both pre-synthesis functional simulation to evaluate logic design accuracy and post-synthesis timing simulation with 0.1-ns resolution. The Timing Analyzer provides pointto-point timing delay information, setup and hold time analysis, and device-wide performance analysis. Figure 24 shows the overall timing model, which maps the possible paths to and from the various elements of the FLEX 10K device. Figure 24. FLEX 10K Device Timing Model Dedicated Clock/Input Interconnect Logic Element 56 I/O Element Embedded Array Block Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figures 25 through 27 show the delays that correspond to various paths and functions within the LE, IOE, and EAB timing models. Figure 25. FLEX 10K Device LE Timing Model Cascade-In Carry-In Register Delays LUT Delay Data-In tLUT tRLUT tCO tCOMB tSU tH tPRE tCLR tCLUT Packed Register Delay tPACKED Data-Out Register Control Delay Control-In tC tEN Carry Chain Delay tCGENR tCASC tCGEN tCICO Altera Corporation tLABCARRY tLABCASC Carry-Out Cascade-Out 57 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 26. FLEX 10K Device IOE Timing Model Output Data Delay I/O Register Delays tIOD tIOCO tIOCOMB tIOSU tIOH tIOCLR Data-In I/O Element Control Delay Clock Enable Clear Clock Output Enable Output Delays tOD1 tOD2 tOD3 tXZ tZX1 tZX2 tZX3 tIOC tINREG Input Register Delay I/O Register Feedback Delay Data Feedback into FastTrack Interconnect tIOFD Input Delay tINCOMB Figure 27. FLEX 10K Device EAB Timing Model Data-In Address EAB Data Input Delays Input Register Delays RAM/ROM Block Delays Output Register Delays tEABDATA1 tEABDATA2 tEABCO tEABBYPASS tEABSU tEABH tEABCH tEABCL tAA tDD tWP tWDSU tWDH tWASU tWAH tWO tEABCO tEABBYPASS tEABSU tEABH tEABCH tEABCL Write Enable Input Delays WE Input Register Clock Output Register Clock tEABWE1 tEABWE2 EAB Output Delay tEABOUT Data-Out EAB Clock Delay tEABCLK Figures 28 shows the timing model for bidirectional I/O pin timing. 58 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 28. Synchronous Bidirectional Pin External Timing Model OE Register D Dedicated Clock PRN Q tXZBIDIR tZXBIDIR CLRN tOUTCOBIDIR Output Register D PRN Q CLRN Bidirectional Pin tINSUBIDIR tINHBIDIR Input Register PRN D Q CLRN Tables 32 through 36 describe the FLEX 10K device internal timing parameters. These internal timing parameters are expressed as worst-case values. Using hand calculations, these parameters can be used to estimate design performance. However, before committing designs to silicon, actual worst-case performance should be modeled using timing simulation and analysis. Tables 37 through 38 describe FLEX 10K external timing parameters. Table 32. LE Timing Microparameters (Part 1 of 2) Symbol Note (1) Parameter tLUT LUT delay for data-in tCLUT LUT delay for carry-in tRLUT LUT delay for LE register feedback tPACKED Data-in to packed register delay tEN LE register enable delay tCICO Carry-in to carry-out delay tCGEN Data-in to carry-out delay tCGENR LE register feedback to carry-out delay tCASC Cascade-in to cascade-out delay tC LE register control signal delay tCO LE register clock-to-output delay tCOMB Combinatorial delay Altera Corporation Conditions 59 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 32. LE Timing Microparameters (Part 2 of 2) Symbol Note (1) Parameter tSU LE register setup time for data and enable signals before clock; LE register recovery time after asynchronous clear, preset, or load tH LE register hold time for data and enable signals after clock tPRE LE register preset delay tCLR LE register clear delay tCH Minimum clock high time from clock pin tCL Minimum clock low time from clock pin Table 33. IOE Timing Microparameters Conditions Note (1) Symbol Parameter Conditions tIOD IOE data delay tIOC IOE register control signal delay tIOCO IOE register clock-to-output delay tIOCOMB IOE combinatorial delay tIOSU IOE register setup time for data and enable signals before clock; IOE register recovery time after asynchronous clear tIOH IOE register hold time for data and enable signals after clock tIOCLR IOE register clear time tOD1 Output buffer and pad delay, slow slew rate = off, VCCIO = VCCINT C1 = 35 pF (2) tOD2 Output buffer and pad delay, slow slew rate = off, VCCIO = low voltage C1 = 35 pF (3) C1 = 35 pF (4) tOD3 Output buffer and pad delay, slow slew rate = on tXZ IOE output buffer disable delay tZX1 IOE output buffer enable delay, slow slew rate = off, VCCIO = VCCINT tZX2 IOE output buffer enable delay, slow slew rate = off, VCCIO = low voltage C1 = 35 pF (3) tZX3 IOE output buffer enable delay, slow slew rate = on C1 = 35 pF (4) tINREG IOE input pad and buffer to IOE register delay tIOFD IOE register feedback delay tINCOMB IOE input pad and buffer to FastTrack Interconnect delay 60 C1 = 35 pF (2) Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 34. EAB Timing Microparameters Symbol Note (1) Parameter Conditions tEABDATA1 Data or address delay to EAB for combinatorial input tEABDATA2 Data or address delay to EAB for registered input tEABWE1 Write enable delay to EAB for combinatorial input tEABWE2 Write enable delay to EAB for registered input tEABCLK EAB register clock delay tEABCO EAB register clock-to-output delay tEABBYPASS Bypass register delay tEABSU EAB register setup time before clock tEABH EAB register hold time after clock tAA Address access delay tWP Write pulse width tWDSU Data setup time before falling edge of write pulse (5) tWDH Data hold time after falling edge of write pulse (5) tWASU Address setup time before rising edge of write pulse (5) tWAH Address hold time after falling edge of write pulse (5) tWO Write enable to data output valid delay tDD Data-in to data-out valid delay tEABOUT Data-out delay tEABCH Clock high time tEABCL Clock low time Altera Corporation 61 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 35. EAB Timing Macroparameters Symbol Notes (1), (6) Parameter Conditions tEABAA EAB address access delay tEABRCCOMB EAB asynchronous read cycle time tEABRCREG EAB synchronous read cycle time tEABWP EAB write pulse width tEABWCCOMB EAB asynchronous write cycle time tEABWCREG EAB synchronous write cycle time tEABDD EAB data-in to data-out valid delay tEABDATACO EAB clock-to-output delay when using output registers tEABDATASU EAB data/address setup time before clock when using input register tEABDATAH EAB data/address hold time after clock when using input register tEABWESU EAB WE setup time before clock when using input register tEABWEH EAB WE hold time after clock when using input register tEABWDSU EAB data setup time before falling edge of write pulse when not using input registers tEABWDH EAB data hold time after falling edge of write pulse when not using input registers tEABWASU EAB address setup time before rising edge of write pulse when not using input registers tEABWAH EAB address hold time after falling edge of write pulse when not using input registers tEABWO EAB write enable to data output valid delay 62 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 36. Interconnect Timing Microparameters Symbol Note (1) Parameter Conditions tDIN2IOE Delay from dedicated input pin to IOE control input (7) tDCLK2LE Delay from dedicated clock pin to LE or EAB clock (7) tDIN2DATA Delay from dedicated input or clock to LE or EAB data (7) tDCLK2IOE Delay from dedicated clock pin to IOE clock (7) tDIN2LE Delay from dedicated input pin to LE or EAB control input (7) tSAMELAB Routing delay for an LE driving another LE in the same LAB tSAMEROW Routing delay for a row IOE, LE, or EAB driving a row IOE, LE, or EAB in the (7) same row tSAMECOLUMN Routing delay for an LE driving an IOE in the same column tDIFFROW Routing delay for a column IOE, LE, or EAB driving an LE or EAB in a different (7) row tTWOROWS Routing delay for a row IOE or EAB driving an LE or EAB in a different row (7) tLEPERIPH Routing delay for an LE driving a control signal of an IOE via the peripheral control bus (7) tLABCARRY Routing delay for the carry-out signal of an LE driving the carry-in signal of a different LE in a different LAB tLABCASC Routing delay for the cascade-out signal of an LE driving the cascade-in signal of a different LE in a different LAB Table 37. External Timing Parameters Symbol (7) Notes (8), (10) Parameter tDRR Register-to-register delay via four LEs, three row interconnects, and four local (9) interconnects tINSU Setup time with global clock at IOE register tINH Hold time with global clock at IOE register tOUTCO Clock-to-output delay with global clock at IOE register Table 38. External Bidirectional Timing Parameters Symbol Note (10) Parameter tINSUBIDIR Setup time for bidirectional pins with global clock at adjacent LE register tINHBIDIR Hold time for bidirectional pins with global clock at adjacent LE register tOUTCOBIDIR Clock-to-output delay for bidirectional pins with global clock at IOE register tXZBIDIR Synchronous IOE output buffer disable delay tZXBIDIR Synchronous IOE output buffer enable delay, slow slew rate = off Altera Corporation Conditions Condition 63 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) Microparameters are timing delays contributed by individual architectural elements. These parameters cannot be measured explicitly. (2) Operating conditions: VCCIO = 5.0 V 5% for commercial use in FLEX 10K devices. VCCIO = 5.0 V 10% for industrial use in FLEX 10K devices. VCCIO = 3.3 V 10% for commercial or industrial use in FLEX 10KA devices. (3) Operating conditions: VCCIO = 3.3 V 10% for commercial or industrial use in FLEX 10K devices. VCCIO = 2.5 V 0.2 V for commercial or industrial use in FLEX 10KA devices. (4) Operating conditions: VCCIO = 2.5 V, 3.3 V, or 5.0 V. (5) Because the RAM in the EAB is self-timed, this parameter can be ignored when the WE signal is registered. (6) EAB macroparameters are internal parameters that can simplify predicting the behavior of an EAB at its boundary; these parameters are calculated by summing selected microparameters. (7) These parameters are worst-case values for typical applications. Post-compilation timing simulation and timing analysis are required to determine actual worst-case performance. (8) External reference timing parameters are factory-tested, worst-case values specified by Altera. A representative subset of signal paths is tested to approximate typical device applications. (9) Contact Altera Applications for test circuit specifications and test conditions. (10) These timing parameters are sample-tested only. Figures 29 and 30 show the asynchronous and synchronous timing waveforms, respectively, for the EAB macroparameters in Table 34. Figure 29. EAB Asynchronous Timing Waveforms EAB Asynchronous Read WE a0 Address a1 a2 tEABAA Data-Out a3 tEABRCCOMB d0 d3 d2 d1 EAB Asynchronous Write WE tEABWP tEABWDSU din0 Data-In tEABWDH din1 tEABWASU tEABWAH tEABWCCOMB Address a0 a1 a2 tEABDD Data-Out 64 din0 din1 dout2 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 30. EAB Synchronous Timing Waveforms EAB Synchronous Read WE Address a0 a1 tEABDATASU a2 a3 tEABRCREG tEABDATAH CLK tEABDATACO Data-Out d2 d1 EAB Synchronous Write (EAB Output Registers Used) WE Data-In Address a0 din1 din2 din3 a1 a2 a3 tEABWESU tEABDATASU tEABDATAH a2 tEABWEH CLK tEABDATACO tEABWCREG Data-Out Altera Corporation dout0 dout1 din1 din2 din3 din2 65 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Tables 39 through 47 show EPF10K10 and EPF10K20 device internal and external timing parameters. Table 39. EPF10K10 & EPF10K20 Device LE Timing Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tLUT 1.4 1.7 ns tCLUT 0.6 0.7 ns tRLUT 1.5 1.9 ns tPACKED 0.6 0.9 ns tEN 1.0 1.2 ns tCICO 0.2 0.3 ns tCGEN 0.9 1.2 ns tCGENR 0.9 1.2 ns tCASC 0.8 0.9 ns tC 1.3 1.5 ns tCO 0.9 1.1 ns tCOMB 0.5 0.6 ns tSU 1.3 2.5 tH 1.4 1.6 tPRE 1.0 ns 1.2 1.0 tCLR ns 1.2 ns ns tCH 4.0 4.0 ns tCL 4.0 4.0 ns 66 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 40. EPF10K10 & EPF10K20 Device IOE Timing Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tIOD 1.3 1.6 ns tIOC 0.5 0.7 ns tIOCO 0.2 0.2 ns tIOCOMB 0.0 0.0 ns tIOSU 2.8 tIOH 1.0 3.2 ns 1.2 ns tIOCLR 1.0 1.2 ns tOD1 2.6 3.5 ns tOD2 4.9 6.4 ns tOD3 6.3 8.2 ns tXZ 4.5 5.4 ns tZX1 4.5 5.4 ns tZX2 6.8 8.3 ns tZX3 8.2 10.1 ns tINREG 6.0 7.5 ns tIOFD 3.1 3.5 ns tINCOMB 3.1 3.5 ns Altera Corporation 67 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 41. EPF10K10 & EPF10K20 Device EAB Internal Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tEABDATA1 1.5 1.9 ns tEABDATA2 4.8 6.0 ns tEABWE1 1.0 1.2 ns tEABWE2 5.0 6.2 ns tEABCLK 1.0 2.2 ns tEABCO 0.5 0.6 ns tEABBYPASS 1.5 1.9 ns tEABSU 1.5 1.8 ns tEABH 2.0 2.5 ns 8.7 tAA 10.7 ns tWP 5.8 7.2 ns tWDSU 1.6 2.0 ns tWDH 0.3 0.4 ns tWASU 0.5 0.6 ns tWAH 1.0 1.2 ns tWO 5.0 6.2 ns tDD 5.0 6.2 ns 0.6 ns 0.5 tEABOUT tEABCH 4.0 4.0 ns tEABCL 5.8 7.2 ns 68 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 42. EPF10K10 & EPF10K20 Device EAB Internal Timing Macroparameters Symbol -3 Speed Grade Min tEABAA tEABRCCOMB Max Note (1) -4 Speed Grade Min 13.7 Unit Max 17.0 ns 13.7 17.0 ns tEABRCREG 9.7 11.9 ns tEABWP 5.8 7.2 ns tEABWCCOMB 7.3 9.0 ns tEABWCREG 13.0 tEABDD 16.0 10.0 2.0 tEABDATACO ns 12.5 ns 3.4 ns tEABDATASU 5.3 5.6 ns tEABDATAH 0.0 0.0 ns tEABWESU 5.5 5.8 ns tEABWEH 0.0 0.0 ns tEABWDSU 5.5 5.8 ns tEABWDH 0.0 0.0 ns tEABWASU 2.1 2.7 ns tEABWAH 0.0 0.0 tEABWO Altera Corporation 9.5 ns 11.8 ns 69 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 43. EPF10K10 Device Interconnect Timing Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tDIN2IOE 4.8 6.2 ns tDIN2LE 2.6 3.8 ns tDIN2DATA 4.3 5.2 ns tDCLK2IOE 3.4 4.0 ns tDCLK2LE 2.6 3.8 ns tSAMELAB 0.6 0.6 ns tSAMEROW 3.6 3.8 ns tSAMECOLUMN 0.9 1.1 ns tDIFFROW 4.5 4.9 ns tTWOROWS 8.1 8.7 ns tLEPERIPH 3.3 3.9 ns tLABCARRY 0.5 0.8 ns tLABCASC 2.7 3.0 ns Table 44. EPF10K20 Device Interconnect Timing Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tDIN2IOE 5.2 6.6 ns tDIN2LE 2.6 3.8 ns tDIN2DATA 4.3 5.2 ns tDCLK2IOE 4.3 4.0 ns tDCLK2LE 2.6 3.8 ns tSAMELAB 0.6 0.6 ns tSAMEROW 3.7 3.9 ns tSAMECOLUMN 1.4 1.6 ns tDIFFROW 5.1 5.5 ns tTWOROWS 8.8 9.4 ns tLEPERIPH 4.7 5.6 ns tLABCARRY 0.5 0.8 ns tLABCASC 2.7 3.0 ns 70 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 45. EPF10K10 & EPF10K20 Device External Timing Parameters Symbol -3 Speed Grade Min tDRR Max Note (1) -4 Speed Grade Min Max 16.1 tINSU (2), (3) 5.5 tINH (3) 0.0 tOUTCO (3) 2.0 20.0 6.0 Symbol -3 Speed Grade Min tINSUBIDIR 4.5 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max ns 2.0 Table 46. EPF10K10 Device External Bidirectional Timing Parameters 8.4 ns Note (1) -4 Speed Grade Min Unit Max 5.6 ns 0.0 6.7 ns ns 0.0 6.7 Unit ns 2.0 8.4 ns tXZBIDIR 10.5 13.4 ns tZXBIDIR 10.5 13.4 ns Table 47. EPF10K20 Device External Bidirectional Timing Parameters Symbol -3 Speed Grade Min tINSUBIDIR 4.6 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max Note (1) -4 Speed Grade Min Max 5.7 ns 0.0 6.7 2.0 Unit ns 8.4 ns tXZBIDIR 10.5 13.4 ns tZXBIDIR 10.5 13.4 ns Notes to tables: (1) (2) (3) All timing parameters are described in Tables 32 through 38 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. Altera Corporation 71 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Tables 48 through 56 show EPF10K30, EPF10K40, and EPF10K50 device internal and external timing parameters. Table 48. EPF10K30, EPF10K40 & EPF10K50 Device LE Timing Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tLUT 1.3 1.8 ns tCLUT 0.6 0.6 ns tRLUT 1.5 2.0 ns tPACKED 0.5 0.8 ns tEN 0.9 1.5 ns tCICO 0.2 0.4 ns tCGEN 0.9 1.4 ns tCGENR 0.9 1.4 ns tCASC 1.0 1.2 ns tC 1.3 1.6 ns tCO 0.9 1.2 ns tCOMB 0.6 0.6 ns tSU 1.4 1.4 tH 0.9 1.3 tPRE 0.9 ns 1.2 0.9 tCLR ns 1.2 ns ns tCH 4.0 4.0 ns tCL 4.0 4.0 ns 72 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 49. EPF10K30, EPF10K40 & EPF10K50 Device IOE Timing Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tIOD 0.4 0.6 ns tIOC 0.5 0.9 ns tIOCO 0.4 0.5 ns tIOCOMB 0.0 0.0 ns tIOSU 3.1 tIOH 1.0 3.5 ns 1.9 ns tIOCLR 1.0 1.2 ns tOD1 3.3 3.6 ns tOD2 5.6 6.5 ns tOD3 7.0 8.3 ns tXZ 5.2 5.5 ns tZX1 5.2 5.5 ns tZX2 7.5 8.4 ns tZX3 8.9 10.2 ns tINREG 7.7 10.0 ns tIOFD 3.3 4.0 ns tINCOMB 3.3 4.0 ns Altera Corporation 73 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 50. EPF10K30, EPF10K40 & EPF10K50 Device EAB Internal Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tEABDATA1 1.5 1.9 ns tEABDATA2 4.8 6.0 ns tEABWE1 1.0 1.2 ns tEABWE2 5.0 6.2 ns tEABCLK 1.0 2.2 ns tEABCO 0.5 0.6 ns tEABBYPASS 1.5 1.9 ns tEABSU 1.5 1.8 ns tEABH 2.0 2.5 ns 8.7 tAA 10.7 ns tWP 5.8 7.2 ns tWDSU 1.6 2.0 ns tWDH 0.3 0.4 ns tWASU 0.5 0.6 ns tWAH 1.0 1.2 ns tWO 5.0 6.2 ns tDD 5.0 6.2 ns 0.6 ns 0.5 tEABOUT tEABCH 4.0 4.0 ns tEABCL 5.8 7.2 ns 74 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 51. EPF10K30, EPF10K40 & EPF10K50 Device EAB Internal Timing Macroparameters Symbol -3 Speed Grade Min tEABAA tEABRCCOMB Max -4 Speed Grade Min 13.7 Note (1) Unit Max 17.0 ns 13.7 17.0 ns tEABRCREG 9.7 11.9 ns tEABWP 5.8 7.2 ns tEABWCCOMB 7.3 9.0 ns tEABWCREG 13.0 tEABDD 16.0 10.0 2.0 tEABDATACO ns 12.5 ns 3.4 ns tEABDATASU 5.3 5.6 ns tEABDATAH 0.0 0.0 ns tEABWESU 5.5 5.8 ns tEABWEH 0.0 0.0 ns tEABWDSU 5.5 5.8 ns tEABWDH 0.0 0.0 ns tEABWASU 2.1 2.7 ns tEABWAH 0.0 0.0 tEABWO Altera Corporation 9.5 ns 11.8 ns 75 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 52. EPF10K30 Device Interconnect Timing Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tDIN2IOE 6.9 8.7 ns tDIN2LE 3.6 4.8 ns tDIN2DATA 5.5 7.2 ns tDCLK2IOE 4.6 6.2 ns tDCLK2LE 3.6 4.8 ns tSAMELAB 0.3 0.3 ns tSAMEROW 3.3 3.7 ns tSAMECOLUMN 2.5 2.7 ns tDIFFROW 5.8 6.4 ns tTWOROWS 9.1 10.1 ns tLEPERIPH 6.2 7.1 ns tLABCARRY 0.4 0.6 ns tLABCASC 2.4 3.0 ns Table 53. EPF10K40 Device Interconnect Timing Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tDIN2IOE 7.6 9.4 ns tDIN2LE 3.6 4.8 ns tDIN2DATA 5.5 7.2 ns tDCLK2IOE 4.6 6.2 ns tDCLK2LE 3.6 4.8 ns tSAMELAB 0.3 0.3 ns tSAMEROW 3.3 3.7 ns tSAMECOLUMN 3.1 3.2 ns tDIFFROW 6.4 6.4 ns tTWOROWS 9.7 10.6 ns tLEPERIPH 6.4 7.1 ns tLABCARRY 0.4 0.6 ns tLABCASC 2.4 3.0 ns 76 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 54. EPF10K50 Device Interconnect Timing Microparameters Symbol -3 Speed Grade Min Max Note (1) -4 Speed Grade Min Unit Max tDIN2IOE 8.4 10.2 ns tDIN2LE 3.6 4.8 ns tDIN2DATA 5.5 7.2 ns tDCLK2IOE 4.6 6.2 ns tDCLK2LE 3.6 4.8 ns tSAMELAB 0.3 0.3 ns tSAMEROW 3.3 3.7 ns tSAMECOLUMN 3.9 4.1 ns tDIFFROW 7.2 7.8 ns tTWOROWS 10.5 11.5 ns tLEPERIPH 7.5 8.2 ns tLABCARRY 0.4 0.6 ns tLABCASC 2.4 3.0 ns Table 55. EPF10K30, EPF10K40 & EPF10K50 Device External Timing Parameters Symbol -3 Speed Grade Min tDRR Max -4 Speed Grade Min 17.2 tINSU (2), (3) 5.7 tINH (3) 0.0 tOUTCO (3) 2.0 Note (1) Max 21.1 6.4 2.0 ns 11.2 Table 56. EPF10K30, EPF10K40 & EPF10K50 Device External Bidirectional Timing Parameters Symbol -3 Speed Grade Min tINSUBIDIR 4.1 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max -4 Speed Grade Min Note (1) Unit ns 0.0 2.0 ns Max 4.6 8.8 ns ns 0.0 8.8 Unit ns 11.2 ns tXZBIDIR 12.3 15.0 ns tZXBIDIR 12.3 15.0 ns Altera Corporation 77 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) (3) All timing parameters are described in Tables 32 through 38 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. Tables 57 through 63 show EPF10K70 device internal and external timing parameters. Table 57. EPF10K70 Device LE Timing Microparameters Symbol Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min Max Max Unit Max tLUT 1.3 1.5 2.0 ns tCLUT 0.4 0.4 0.5 ns tRLUT 1.5 1.6 2.0 ns tPACKED 0.8 0.9 1.3 ns tEN 0.8 0.9 1.2 ns tCICO 0.2 0.2 0.3 ns tCGEN 1.0 1.1 1.4 ns tCGENR 1.1 1.2 1.5 ns tCASC 1.0 1.1 1.3 ns tC 0.7 0.8 1.0 ns tCO 0.9 1.0 1.4 ns 0.4 tCOMB tSU 1.9 tH 2.1 0.5 2.1 0.7 2.6 2.3 ns ns 3.1 ns tPRE 0.9 1.0 1.4 ns tCLR 0.9 1.0 1.4 ns tCH 4.0 4.0 4.0 ns tCL 4.0 4.0 4.0 ns 78 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 58. EPF10K70 Device IOE Timing Microparameters Symbol Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min Max Max Unit Max tIOD 0.0 0.0 0.0 ns tIOC 0.4 0.5 0.7 ns tIOCO 0.4 0.4 0.9 ns tIOCOMB 0.0 0.0 0.0 tIOSU 4.5 tIOH 0.4 5.0 6.2 0.5 ns ns 0.7 ns tIOCLR 0.6 0.7 1.6 ns tOD1 3.6 4.0 5.0 ns tOD2 5.6 6.3 7.3 ns tOD3 6.9 7.7 8.7 ns tXZ 5.5 6.2 6.8 ns tZX1 5.5 6.2 6.8 ns tZX2 7.5 8.5 9.1 ns tZX3 8.8 9.9 10.5 ns tINREG 8.0 9.0 10.2 ns tIOFD 7.2 8.1 10.3 ns tINCOMB 7.2 8.1 10.3 ns Altera Corporation 79 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 59. EPF10K70 Device EAB Internal Microparameters Symbol Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.3 1.5 1.9 ns tEABDATA2 4.3 4.8 6.0 ns tEABWE1 0.9 1.0 1.2 ns tEABWE2 4.5 5.0 6.2 ns tEABCLK 0.9 1.0 2.2 ns tEABCO 0.4 0.5 0.6 ns tEABBYPASS 1.3 1.5 1.9 ns tEABSU 1.3 1.5 1.8 ns tEABH 1.8 2.0 2.5 ns 7.8 tAA 8.7 10.7 ns tWP 5.2 5.8 7.2 ns tWDSU 1.4 1.6 2.0 ns tWDH 0.3 0.3 0.4 ns tWASU 0.4 0.5 0.6 ns tWAH 0.9 1.0 1.2 ns tWO 4.5 5.0 6.2 ns tDD 4.5 5.0 6.2 ns 0.6 ns 0.4 tEABOUT 0.5 tEABCH 4.0 4.0 4.0 ns tEABCL 5.2 5.8 7.2 ns 80 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 60. EPF10K70 Device EAB Internal Timing Macroparameters Symbol -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min tEABAA tEABRCCOMB Note (1) Max 12.1 Max 13.7 Unit Max 17.0 ns 12.1 13.7 17.0 ns tEABRCREG 8.6 9.7 11.9 ns tEABWP 5.2 5.8 7.2 ns tEABWCCOMB 6.5 7.3 9.0 ns tEABWCREG 11.6 tEABDD 13.0 8.8 1.7 tEABDATACO 16.0 10.0 ns 12.5 2.0 3.4 ns ns tEABDATASU 4.7 5.3 5.6 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 4.9 5.5 5.8 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 1.8 2.1 2.7 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 4.1 4.7 5.8 ns tEABWAH 0.0 0.0 0.0 tEABWO Altera Corporation 8.4 9.5 ns 11.8 ns 81 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 61. EPF10K70 Device Interconnect Timing Microparameters Symbol Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min Max Max Unit Max tDIN2IOE 6.6 7.3 8.8 ns tDIN2LE 4.2 4.8 6.0 ns tDIN2DATA 6.5 7.1 10.8 ns tDCLK2IOE 5.5 6.2 7.7 ns tDCLK2LE 4.2 4.8 6.0 ns tSAMELAB 0.4 0.4 0.5 ns tSAMEROW 4.8 4.9 5.5 ns tSAMECOLUMN 3.3 3.4 3.7 ns tDIFFROW 8.1 8.3 9.2 ns tTWOROWS 12.9 13.2 14.7 ns tLEPERIPH 5.5 5.7 6.5 ns tLABCARRY 0.8 0.9 1.1 ns tLABCASC 2.7 3.0 3.2 ns Table 62. EPF10K70 Device External Timing Parameters Symbol -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min tDRR Max 17.2 tINSU (2), (3) Note (1) 6.6 tINH (3) 0.0 tOUTCO (3) 2.0 Max 19.1 7.3 2.0 -2 Speed Grade -3 Speed Grade Min Min tINSUBIDIR 7.4 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max Max 8.1 2.0 2.0 ns 14.3 ns Note (1) -4 Speed Grade Min 2.0 Unit Max ns 0.0 11.1 ns ns 10.4 0.0 9.9 24.2 0.0 11.1 Table 63. EPF10K70 Device External Bidirectional Timing Parameters Symbol Max 8.0 0.0 9.9 Unit ns 14.3 ns tXZBIDIR 13.7 15.4 18.5 ns tZXBIDIR 13.7 15.4 18.5 ns 82 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) (3) All timing parameters are described in Tables 32 through 38 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. Tables 64 through 70 show EPF10K100 device internal and external timing parameters. Table 64. EPF10K100 Device LE Timing Microparameters Symbol -3DX Speed Grade Min Max Note (1) -3 Speed Grade -4 Speed Grade Min Min Max Unit Max tLUT 1.5 1.5 2.0 ns tCLUT 0.4 0.4 0.5 ns tRLUT 1.6 1.6 2.0 ns tPACKED 0.9 0.9 1.3 ns tEN 0.9 0.9 1.2 ns tCICO 0.2 0.2 0.3 ns tCGEN 1.1 1.1 1.4 ns tCGENR 1.2 1.2 1.5 ns tCASC 1.1 1.1 1.3 ns tC 0.8 0.8 1.0 ns tCO 1.0 1.0 1.4 ns tCOMB 0.5 0.5 0.7 ns tSU 2.1 tH 2.3 2.1 2.3 1.0 tPRE tCLR 2.6 3.1 1.0 1.0 ns 1.0 ns 1.4 ns 1.4 ns tCH 4.0 4.0 4.0 ns tCL 4.0 4.0 4.0 ns Altera Corporation 83 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 65. EPF10K100 Device IOE Timing Microparameters Symbol -3DX Speed Grade Min Max Note (1) -3 Speed Grade -4 Speed Grade Min Min Max Unit Max tIOD 0.0 0.0 0.0 ns tIOC 0.5 0.5 0.7 ns tIOCO 0.4 0.4 0.9 ns tIOCOMB 0.0 0.0 0.0 ns tIOSU 5.5 tIOH 0.5 5.5 6.7 0.5 ns 0.7 ns tIOCLR 0.7 0.7 1.6 ns tOD1 4.0 4.0 5.0 ns tOD2 6.3 6.3 7.3 ns tOD3 7.7 7.7 8.7 ns tXZ 6.2 6.2 6.8 ns tZX1 6.2 6.2 6.8 ns tZX2 8.5 8.5 9.1 ns tZX3 9.9 9.9 10.5 ns tINREG without ClockLock or ClockBoost circuitry 9.0 9.0 10.5 ns tINREG with ClockLock or ClockBoost circuitry 3.0 - - ns tIOFD 8.1 8.1 10.3 ns tINCOMB 8.1 8.1 10.3 ns 84 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 66. EPF10K100 Device EAB Internal Microparameters Symbol -3DX Speed Grade Min Max Note (1) -3 Speed Grade -4 Speed Grade Min Min Max Unit Max tEABDATA1 1.5 1.5 1.9 ns tEABDATA2 4.8 4.8 6.0 ns tEABWE1 1.0 1.0 1.2 ns tEABWE2 5.0 5.0 6.2 ns tEABCLK 1.0 1.0 2.2 ns tEABCO 0.5 0.5 0.6 ns tEABBYPASS 1.5 1.5 1.9 ns tEABSU 1.5 1.5 1.8 ns tEABH 2.0 2.0 2.5 ns 8.7 tAA 8.7 10.7 ns tWP 5.8 5.8 7.2 ns tWDSU 1.6 1.6 2.0 ns tWDH 0.3 0.3 0.4 ns tWASU 0.5 0.5 0.6 ns tWAH 1.0 1.0 1.2 ns tWO 5.0 5.0 6.2 ns tDD 5.0 5.0 6.2 ns 0.6 ns 0.5 tEABOUT 0.5 tEABCH 4.0 4.0 4.0 ns tEABCL 5.8 5.8 7.2 ns Altera Corporation 85 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 67. EPF10K100 Device EAB Internal Timing Macroparameters Symbol -3DX Speed Grade Min tEABAA tEABRCCOMB Max Note (1) -3 Speed Grade -4 Speed Grade Min Min 13.7 Max 13.7 Unit Max 17.0 ns 13.7 13.7 17.0 ns tEABRCREG 9.7 9.7 11.9 ns tEABWP 5.8 5.8 7.2 ns tEABWCCOMB 7.3 7.3 9.0 ns tEABWCREG 13.0 tEABDD 13.0 10.0 2.0 tEABDATACO 16.0 10.0 ns 12.5 2.0 3.4 ns ns tEABDATASU 5.3 5.3 5.6 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 5.5 5.5 5.8 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 5.5 5.5 5.8 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 2.1 2.1 2.7 ns tEABWAH 0.0 0.0 0.0 tEABWO 86 9.5 9.5 ns 11.8 ns Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 68. EPF10K100 Device Interconnect Timing Microparameters Symbol -3DX Speed Grade Min Max Note (1) -3 Speed Grade Min Max -4 Speed Grade Min Unit Max tDIN2IOE 10.3 10.3 12.2 ns tDIN2LE 4.8 4.8 6.0 ns tDIN2DATA 7.3 7.3 11.0 ns tDCLK2IOE without ClockLock or ClockBoost circuitry 6.2 6.2 7.7 ns tDCLK2IOE with ClockLock or ClockBoost circuitry 2.3 - - ns tDCLK2LE without ClockLock or ClockBoost circuitry 4.8 4.8 6.0 ns tDCLK2LE with ClockLock or ClockBoost circuitry 2.3 - - ns tSAMELAB 0.4 0.4 0.5 ns tSAMEROW 4.9 4.9 5.5 ns tSAMECOLUMN 5.1 5.1 5.4 ns tDIFFROW 10.0 10.0 10.9 ns tTWOROWS 14.9 14.9 16.4 ns tLEPERIPH 6.9 6.9 8.1 ns tLABCARRY 0.9 0.9 1.1 ns tLABCASC 3.0 3.0 3.2 ns Altera Corporation 87 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 69. EPF10K100 Device External Timing Parameters Symbol -3DX Speed Grade Min tDRR Max -3 Speed Grade -4 Speed Grade Min Min 19.1 tINSU (2), (3), (4) 7.8 Note (1) Max 19.1 7.8 11.1 2.0 Max 24.2 8.5 ns tOUTCO (3), (4) 2.0 0.0 0.0 0.0 ns tINSU (2), (3), (5) 6.2 - - ns tOUTCO (3), (5) 2.0 - Table 70. EPF10K100 Device External Bidirectional Timing Parameters Symbol -3DX Speed Grade Min Max 2.0 ns tINH (3) 6.7 11.1 Unit 14.3 - ns Note (1) -3 Speed Grade -4 Speed Grade Min Min Max ns Unit Max tINSUBIDIR (4) 8.1 8.1 10.4 ns tINHBIDIR (4) 0.0 0.0 0.0 ns tOUTCOBIDIR (4) 2.0 14.3 ns tXZBIDIR (4) 11.1 15.3 2.0 11.1 15.3 2.0 18.4 ns tZXBIDIR (4) 15.3 15.3 18.4 ns tINSUBIDIR (5) 9.1 - - ns tINHBIDIR (5) 0.0 - - ns tOUTCOBIDIR (5) 2.0 - ns tXZBIDIR (5) 14.3 7.2 - - - - - ns tZXBIDIR (5) 14.3 - - ns Notes to tables: (1) (2) (3) (4) (5) 88 All timing parameters are described in Tables 32 through 38 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. This parameter is measured without the use of the ClockLock or ClockBoost circuits. This parameter is measured with the use of the ClockLock or ClockBoost circuits. Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Tables 71 through 77 show EPF10K50V device internal and external timing parameters. Table 71. EPF10K50V Device LE Timing Microparameters Symbol -1 Speed Grade Min Max -2 Speed Grade Min Max Note (1) -3 Speed Grade Min Max -4 Speed Grade Min Unit Max tLUT 0.9 1.0 1.3 1.6 ns tCLUT 0.1 0.5 0.6 0.6 ns tRLUT 0.5 0.8 0.9 1.0 ns tPACKED 0.4 0.4 0.5 0.7 ns tEN 0.7 0.9 1.1 1.4 ns tCICO 0.2 0.2 0.2 0.3 ns tCGEN 0.8 0.7 0.8 1.2 ns tCGENR 0.4 0.3 0.3 0.4 ns tCASC 0.7 0.7 0.8 0.9 ns tC 0.3 1.0 1.3 1.5 ns tCO 0.5 0.7 0.9 1.0 ns tCOMB 0.4 0.4 0.5 0.6 ns tSU 0.8 1.6 2.2 2.5 tH 0.5 0.8 1.0 1.4 tPRE 0.8 0.4 0.8 tCLR 0.5 0.4 0.5 ns ns 0.5 ns 0.5 ns tCH 2.0 4.0 4.0 4.0 ns tCL 2.0 4.0 4.0 4.0 ns Altera Corporation 89 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 72. EPF10K50V Device IOE Timing Microparameters Symbol -1 Speed Grade Min Max -2 Speed Grade Min Max Note (1) -3 Speed Grade Min Max -4 Speed Grade Min Unit Max tIOD 1.2 1.6 1.9 2.1 ns tIOC 0.3 0.4 0.5 0.5 ns tIOCO 0.3 0.3 0.4 0.4 ns tIOCOMB 0.0 0.0 0.0 0.0 tIOSU 2.8 tIOH 0.7 2.8 3.4 0.8 3.9 1.0 ns ns 1.4 ns tIOCLR 0.5 0.6 0.7 0.7 tOD1 2.8 3.2 3.9 4.7 ns tOD2 - - - - ns tOD3 6.5 6.9 7.6 8.4 ns tXZ 2.8 3.1 3.8 4.6 ns tZX1 2.8 3.1 3.8 4.6 ns ns tZX2 - - - - ns tZX3 6.5 6.8 7.5 8.3 ns tINREG 5.0 5.7 7.0 9.0 ns tIOFD 1.5 1.9 2.3 2.7 ns tINCOMB 1.5 1.9 2.3 2.7 ns 90 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 73. EPF10K50V Device EAB Internal Microparameters Symbol -1 Speed Grade Min Max -2 Speed Grade Min Max Note (1) -3 Speed Grade Min Max -4 Speed Grade Min Unit Max tEABDATA1 1.7 2.8 3.4 4.6 ns tEABDATA2 4.9 3.9 4.8 5.9 ns tEABWE1 0.0 2.5 3.0 3.7 ns tEABWE2 4.0 4.1 5.0 6.2 ns tEABCLK 0.4 0.8 1.0 1.2 ns tEABCO 0.1 0.2 0.3 0.4 ns tEABBYPASS 0.9 1.1 1.3 1.6 ns tEABSU 0.8 1.5 1.8 2.2 ns tEABH 0.8 1.6 2.0 2.5 ns 5.5 tAA 8.2 10.0 12.4 ns tWP 6.0 4.9 6.0 7.4 ns tWDSU 0.1 0.8 1.0 1.2 ns tWDH 0.1 0.2 0.3 0.4 ns tWASU 0.1 0.4 0.5 0.6 ns tWAH 0.1 0.8 1.0 1.2 ns tWO 2.8 4.3 5.3 6.5 ns tDD 2.8 4.3 5.3 6.5 ns 0.6 ns 0.5 tEABOUT 0.4 0.5 tEABCH 2.0 4.0 4.0 4.0 ns tEABCL 6.0 4.9 6.0 7.4 ns Altera Corporation 91 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 74. EPF10K50V Device EAB Internal Timing Macroparameters Symbol -1 Speed Grade Min tEABAA Max -2 Speed Grade Min 9.5 Max Note (1) -3 Speed Grade Min 13.6 Max -4 Speed Grade Min 16.5 Unit Max 20.8 ns tEABRCCOMB 9.5 13.6 16.5 20.8 ns tEABRCREG 6.1 8.8 10.8 13.4 ns tEABWP 6.0 4.9 6.0 7.4 ns tEABWCCOMB 6.2 6.1 7.5 9.2 ns tEABWCREG 12.0 tEABDD 11.6 6.8 1.0 tEABDATACO 14.2 9.7 17.4 11.8 1.4 1.8 ns 14.9 ns 2.2 ns tEABDATASU 5.3 4.6 5.6 6.9 ns tEABDATAH 0.0 0.0 0.0 0.0 ns tEABWESU 4.4 4.8 5.8 7.2 ns tEABWEH 0.0 0.0 0.0 0.0 ns tEABWDSU 1.8 1.1 1.4 2.1 ns tEABWDH 0.0 0.0 0.0 0.0 ns tEABWASU 4.5 4.6 5.6 7.4 ns tEABWAH 0.0 0.0 0.0 0.0 tEABWO 92 5.1 9.4 11.4 ns 14.0 ns Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 75. EPF10K50V Device Interconnect Timing Microparameters Symbol -1 Speed Grade Min Max -2 Speed Grade Min Max Note (1) -3 Speed Grade Min Max -4 Speed Grade Min Unit Max tDIN2IOE 4.7 6.0 7.1 8.2 ns tDIN2LE 2.5 2.6 3.1 3.9 ns tDIN2DATA 4.4 5.9 6.8 7.7 ns tDCLK2IOE 2.5 3.9 4.7 5.5 ns tDCLK2LE 2.5 2.6 3.1 3.9 ns tSAMELAB 0.2 0.2 0.3 0.3 ns tSAMEROW 2.8 3.0 3.2 3.4 ns tSAMECOLUMN 3.0 3.2 3.4 3.6 ns tDIFFROW 5.8 6.2 6.6 7.0 ns tTWOROWS 8.6 9.2 9.8 10.4 ns tLEPERIPH 4.5 5.5 6.1 7.0 ns tLABCARRY 0.3 0.4 0.5 0.7 ns tLABCASC 0.0 1.3 1.6 2.0 ns Table 76. EPF10K50V Device External Timing Parameters Symbol -1 Speed Grade Min tDRR Max -2 Speed Grade Min 11.2 tINSU (2), (3) 5.5 tINH (3) 0.0 tOUTCO (3) 2.0 Max -3 Speed Grade Min 14.0 4.2 2.0 Max 2.0 -1 Speed Grade Min tINSUBIDIR 2.0 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max -2 Speed Grade Min Max 2.8 2.0 Max 3.5 0.0 5.9 -3 Speed Grade Min 2.0 ns 11.1 ns Note (1) -4 Speed Grade Min 2.0 Unit Max ns 0.0 9.5 ns ns 4.1 0.0 7.8 21.1 2.0 Unit Max 0.0 9.5 Table 77. EPF10K50V Device External Bidirectional Timing Parameters Symbol Min 6.9 0.0 7.8 -4 Speed Grade 17.2 5.2 0.0 5.9 Note (1) ns 11.1 ns tXZBIDIR 8.0 9.8 11.8 14.3 ns tZXBIDIR 8.0 9.8 11.8 14.3 ns Altera Corporation 93 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) (3) All timing parameters are described in Tables 32 through 38 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. Tables 78 through 84 show EPF10K130V device internal and external timing parameters. Table 78. EPF10K130V Device LE Timing Microparameters Symbol Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min Max Max Unit Max tLUT 1.3 1.8 2.3 ns tCLUT 0.5 0.7 0.9 ns tRLUT 1.2 1.7 2.2 ns tPACKED 0.5 0.6 0.7 ns tEN 0.6 0.8 1.0 ns tCICO 0.2 0.3 0.4 ns tCGEN 0.3 0.4 0.5 ns tCGENR 0.7 1.0 1.3 ns tCASC 0.9 1.2 1.5 ns tC 1.9 2.4 3.0 ns tCO 0.6 0.9 1.1 ns 0.5 tCOMB tSU 0.2 tH 0.0 0.7 0.2 0.9 0.3 0.0 ns ns 0.0 ns tPRE 2.4 3.1 3.9 ns tCLR 2.4 3.1 3.9 ns tCH 4.0 4.0 4.0 ns tCL 4.0 4.0 4.0 ns 94 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 79. EPF10K130V Device IOE Timing Microparameters Symbol Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min Max Max Unit Max tIOD 1.3 1.6 2.0 ns tIOC 0.4 0.5 0.7 ns tIOCO 0.3 0.4 0.5 ns tIOCOMB 0.0 0.0 0.0 tIOSU 2.6 tIOH 0.0 3.3 3.8 0.0 ns ns 0.0 ns tIOCLR 1.7 2.2 2.7 ns tOD1 3.5 4.4 5.0 ns tOD2 - - - ns tOD3 8.2 8.1 9.7 ns tXZ 4.9 6.3 7.4 ns tZX1 4.9 6.3 7.4 ns tZX2 - - - ns tZX3 9.6 10.0 12.1 ns tINREG 7.9 10.0 12.6 ns tIOFD 6.2 7.9 9.9 ns tINCOMB 6.2 7.9 9.9 ns Altera Corporation 95 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 80. EPF10K130V Device EAB Internal Microparameters Symbol Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.9 2.4 2.4 ns tEABDATA2 3.7 4.7 4.7 ns tEABWE1 1.9 2.4 2.4 ns tEABWE2 3.7 4.7 4.7 ns tEABCLK 0.7 0.9 0.9 ns tEABCO 0.5 0.6 0.6 ns tEABBYPASS 0.6 0.8 0.8 ns tEABSU 1.4 1.8 1.8 ns tEABH 0.0 0.0 0.0 ns 5.6 tAA 7.1 7.1 ns tWP 3.7 4.7 4.7 ns tWDSU 4.6 5.9 5.9 ns tWDH 0.0 0.0 0.0 ns tWASU 3.9 5.0 5.0 ns tWAH 0.0 0.0 0.0 ns tWO 5.6 7.1 7.1 ns tDD 5.6 7.1 7.1 ns 2.4 tEABOUT 3.1 3.1 ns tEABCH 4.0 4.0 4.0 ns tEABCL 4.0 4.7 4.7 ns 96 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 81. EPF10K130V Device EAB Internal Timing Macroparameters Symbol -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min tEABAA tEABRCCOMB Note (1) Max 11.2 Max 14.2 Unit Max 14.2 ns 11.1 14.2 14.2 ns tEABRCREG 8.5 10.8 10.8 ns tEABWP 3.7 4.7 4.7 ns tEABWCCOMB 7.6 9.7 9.7 ns tEABWCREG 14.0 tEABDD 17.8 11.1 3.6 tEABDATACO 17.8 14.2 ns 14.2 4.6 4.6 ns ns tEABDATASU 4.4 5.6 5.6 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 4.4 5.6 5.6 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 4.6 5.9 5.9 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 3.9 5.0 5.0 ns tEABWAH 0.0 0.0 0.0 tEABWO Altera Corporation 11.1 14.2 ns 14.2 ns 97 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 82. EPF10K130V Device Interconnect Timing Microparameters Symbol Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min Max Max Unit Max tDIN2IOE 8.0 9.0 9.5 ns tDIN2LE 2.4 3.0 3.1 ns tDIN2DATA 5.0 6.3 7.4 ns tDCLK2IOE 3.6 4.6 5.1 ns tDCLK2LE 2.4 3.0 3.1 ns tSAMELAB 0.4 0.6 0.8 ns tSAMEROW 4.5 5.3 6.5 ns 9.0 9.5 9.7 ns tDIFFROW 13.5 14.8 16.2 ns tTWOROWS 18.0 20.1 22.7 ns tLEPERIPH 8.1 8.6 9.5 ns tLABCARRY 0.6 0.8 1.0 ns tLABCASC 0.8 1.0 1.2 ns tSAMECOLUMN Table 83. EPF10K130V Device External Timing Parameters Symbol Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min tDRR Max 15.0 tINSU (2), (3) 6.9 tINH (3) 0.0 tOUTCO (3) 2.0 Max 19.1 8.6 2.0 -2 Speed Grade -3 Speed Grade Min Min tINSUBIDIR 6.7 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max Max 8.5 2.0 2.0 ns 11.3 ns Note (1) -4 Speed Grade Min 2.0 Unit Max ns 0.0 8.8 ns ns 10.8 0.0 6.9 24.2 0.0 9.9 Table 84. EPF10K130V Device External Bidirectional Timing Parameters Symbol Max 11.0 0.0 7.8 Unit ns 10.2 ns tXZBIDIR 12.9 16.4 19.3 ns tZXBIDIR 12.9 16.4 19.3 ns 98 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) (3) All timing parameters are described in Tables 32 through 38 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. Tables 85 through 91 show EPF10K10A device internal and external timing parameters. Table 85. EPF10K10A Device LE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.9 1.2 1.6 ns tCLUT 1.2 1.4 1.9 ns tRLUT 1.9 2.3 3.0 ns tPACKED 0.6 0.7 0.9 ns tEN 0.5 0.6 0.8 ns tCICO 02 0.3 0.4 ns tCGEN 0.7 0.9 1.1 ns tCGENR 0.7 0.9 1.1 ns tCASC 1.0 1.2 1.7 ns tC 1.2 1.4 1.9 ns tCO 0.5 0.6 0.8 ns tCOMB 0.5 0.6 0.8 ns tSU 1.1 tH 0.6 1.3 0.7 0.5 tPRE tCLR 1.7 0.9 0.6 0.5 ns 0.6 ns 0.9 ns 0.9 ns tCH 3.0 3.5 4.0 ns tCL 3.0 3.5 4.0 ns Table 86. EPF10K10A Device IOE Timing Microparameters Symbol Note (1) (Part 1 of 2) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max 1.3 1.5 2.0 ns tIOC 0.2 0.3 0.3 ns tIOCO 0.2 0.3 0.4 ns tIOCOMB 0.6 0.7 0.9 ns tIOSU Altera Corporation 0.8 1.0 1.3 ns 99 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 86. EPF10K10A Device IOE Timing Microparameters Symbol tIOH Note (1) (Part 2 of 2) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max 0.8 Max 1.0 Unit Max 1.3 ns tIOCLR 1.2 1.4 1.9 ns tOD1 1.2 1.4 1.9 ns tOD2 2.9 3.5 4.7 ns tOD3 6.6 7.8 10.5 ns tXZ 1.2 1.4 1.9 ns tZX1 1.2 1.4 1.9 ns tZX2 2.9 3.5 4.7 ns tZX3 6.6 7.8 10.5 ns tINREG 5.2 6.3 8.4 ns tIOFD 3.1 3.8 5.0 ns tINCOMB 3.1 3.8 5.0 ns 100 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 87. EPF10K10A Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 3.3 3.9 5.2 ns tEABDATA2 1.0 1.3 1.7 ns tEABWE1 2.6 3.1 4.1 ns tEABWE2 2.7 3.2 4.3 ns tEABCLK 0.0 0.0 0.0 ns tEABCO 1.2 1.4 1.8 ns tEABBYPASS 0.1 0.2 0.2 ns tEABSU 1.4 1.7 2.2 ns tEABH 0.1 0.1 0.1 ns 4.5 tAA 5.4 7.3 ns tWP 2.0 2.4 3.2 ns tWDSU 0.7 0.8 1.1 ns tWDH 0.5 0.6 0.7 ns tWASU 0.6 0.7 0.9 ns tWAH 0.9 1.1 1.5 ns tWO 3.3 3.9 5.2 ns tDD 3.3 3.9 5.2 ns 0.2 ns 0.1 tEABOUT 0.1 tEABCH 3.0 3.5 4.0 ns tEABCL 3.03 3.5 4.0 ns Altera Corporation 101 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 88. EPF10K10A Device EAB Internal Timing Macroparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 8.1 Max 9.8 Unit Max 13.1 ns tEABRCCOMB 8.1 9.8 13.1 ns tEABRCREG 5.8 6.9 9.3 ns tEABWP 2.0 2.4 3.2 ns tEABWCCOMB 3.5 4.2 5.6 ns tEABWCREG 9.4 tEABDD 11.2 6.9 1.3 tEABDATACO 14.8 8.3 ns 11.0 1.5 2.0 ns ns tEABDATASU 2.4 3.0 3.9 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 4.1 4.9 6.5 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 1.4 1.6 2.2 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 2.5 3.0 4.1 ns tEABWAH 0.0 0.0 0.0 tEABWO 102 6.2 7.5 ns 9.9 ns Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 89. EPF10K10A Device Interconnect Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tDIN2IOE 4.2 5.0 6.5 ns tDIN2LE 2.2 2.6 3.4 ns tDIN2DATA 4.3 5.2 7.1 ns tDCLK2IOE 4.2 4.9 6.6 ns tDCLK2LE 2.2 2.6 3.4 ns tSAMELAB 0.1 0.1 0.2 ns tSAMEROW 2.2 2.4 2.9 ns tSAMECOLUMN 0.8 1.0 1.4 ns tDIFFROW 3.0 3.4 4.3 ns tTWOROWS 5.2 5.8 7.2 ns tLEPERIPH 1.8 2.2 2.8 ns tLABCARRY 0.5 0.5 0.7 ns tLABCASC 0.9 1.0 1.5 ns Table 90. EPF10K10A External Reference Timing Parameters Symbol -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max tDRR Max 10.0 tINSU (2), (3) Note (1) tINH (3) 0.0 tOUTCO (3) 2.0 16.0 2.1 0.0 5.8 ns 2.8 ns 0.0 2.0 6.9 ns 2.0 Table 91. EPF10K10A Device External Bidirectional Timing Parameters Symbol Max 12.0 1.6 Unit 9.2 ns Note (1) -2 Speed Grade -3 Speed Grade -4 Speed Grade Min Min Min tINSUBIDIR 2.4 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max Max 3.3 2.0 Max 4.5 0.0 5.8 ns 0.0 6.9 2.0 Unit ns 9.2 ns tXZBIDIR 6.3 7.5 9.9 ns tZXBIDIR 6.3 7.5 9.9 ns Altera Corporation 103 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) (3) All timing parameters are described in Tables 32 through 38 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. Tables 92 through 98 show EPF10K30A device internal and external timing parameters. Table 92. EPF10K30A Device LE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.8 1.1 1.5 ns tCLUT 0.6 0.7 1.0 ns tRLUT 1.2 1.5 2.0 ns tPACKED 0.6 0.6 1.0 ns tEN 1.3 1.5 2.0 ns tCICO 0.2 0.3 0.4 ns tCGEN 0.8 1.0 1.3 ns tCGENR 0.6 0.8 1.0 ns tCASC 0.9 1.1 1.4 ns tC 1.1 1.3 1.7 ns tCO 0.4 0.6 0.7 ns tCOMB 0.6 0.7 0.9 ns tSU 0.9 tH 1.1 0.9 1.3 0.5 tPRE tCLR 1.4 1.7 0.6 0.5 ns 0.6 ns 0.8 ns 0.8 ns tCH 3.0 3.5 4.0 ns tCL 3.0 3.5 4.0 ns Table 93. EPF10K30A Device IOE Timing Microparameters Symbol Note (1) (Part 1 of 2) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 2.2 2.6 3.4 ns tIOC 0.3 0.3 0.5 ns tIOCO 0.2 0.2 0.3 ns 0.8 ns 0.5 tIOCOMB tIOSU 104 1.4 0.6 1.7 2.2 ns Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 93. EPF10K30A Device IOE Timing Microparameters Symbol tIOH Note (1) (Part 2 of 2) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max 0.9 Max 1.1 Unit Max 1.4 ns tIOCLR 0.7 0.8 1.0 ns tOD1 1.9 2.2 2.9 ns tOD2 4.8 5.6 7.3 ns tOD3 7.0 8.2 10.8 ns tXZ 2.2 2.6 3.4 ns tZX1 2.2 2.6 3.4 ns tZX2 5.1 6.0 7.8 ns tZX3 7.3 8.6 11.3 ns tINREG 4.4 5.2 6.8 ns tIOFD 3.8 4.5 5.9 ns tINCOMB 3.8 4.5 5.9 ns Altera Corporation 105 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 94. EPF10K30A Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 5.5 6.5 8.5 ns tEABDATA2 1.1 1.3 1.8 ns tEABWE1 2.4 2.8 3.7 ns tEABWE2 2.1 2.5 3.2 ns tEABCLK 0.0 0.0 0.2 ns tEABCO 1.7 2.0 2.6 ns tEABBYPASS 0.0 0.0 0.3 ns tEABSU 1.2 1.4 1.9 ns tEABH 0.1 0.1 0.3 ns 4.2 tAA 5.0 6.5 ns tWP 3.8 4.5 5.9 ns tWDSU 0.1 0.1 0.2 ns tWDH 0.1 0.1 0.2 ns tWASU 0.1 0.1 0.2 ns tWAH 0.1 0.1 0.2 ns tWO 3.7 4.4 6.4 ns tDD 3.7 4.4 6.4 ns 0.6 ns 0.0 tEABOUT 0.1 tEABCH 3.0 3.5 4.0 ns tEABCL 3.8 4.5 5.9 ns 106 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 95. EPF10K30A Device EAB Internal Timing Macroparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 9.7 Max 11.6 Unit Max 16.2 ns tEABRCCOMB 9.7 11.6 16.2 ns tEABRCREG 5.9 7.1 9.7 ns tEABWP 3.8 4.5 5.9 ns tEABWCCOMB 4.0 4.7 6.3 ns tEABWCREG 9.8 tEABDD 11.6 9.2 1.7 tEABDATACO 16.6 11.0 2.1 ns 16.1 ns 3.4 ns tEABDATASU 2.3 2.7 3.5 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 3.3 3.9 4.9 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 3.2 3.8 5.0 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 3.7 4.4 5.1 ns tEABWAH 0.0 0.0 0.0 tEABWO Altera Corporation 6.1 7.3 ns 11.3 ns 107 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 96. EPF10K30A Device Interconnect Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tDIN2IOE 3.9 4.4 5.1 ns tDIN2LE 1.2 1.5 1.9 ns tDIN2DATA 3.2 3.6 4.5 ns tDCLK2IOE 3.0 3.5 4.6 ns tDCLK2LE 1.2 1.5 1.9 ns tSAMELAB 0.1 0.1 0.2 ns tSAMEROW 2.3 2.4 2.7 ns tSAMECOLUMN 1.3 1.4 1.9 ns tDIFFROW 3.6 3.8 4.6 ns tTWOROWS 5.9 6.2 7.3 ns tLEPERIPH 3.5 3.8 4.1 ns tLABCARRY 0.3 0.4 0.5 ns tLABCASC 0.9 1.1 1.4 ns Table 97. EPF10K30A External Reference Timing Parameters Symbol -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max tDRR Max 11.0 tINSU (2), (3) Note (1) tINH (3) 0.0 tOUTCO (3) 2.0 17.0 3.1 0.0 5.4 ns 3.9 ns 0.0 2.0 6.2 ns 2.0 Table 98. EPF10K30A Device External Bidirectional Timing Parameters Symbol Max 13.0 2.5 Unit 8.3 ns Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tINSUBIDIR 4.2 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max Max 4.9 2.0 Max 6.8 0.0 5.4 ns 0.0 6.2 2.0 Unit ns 8.3 ns tXZBIDIR 6.2 7.5 9.8 ns tZXBIDIR 6.2 7.5 9.8 ns 108 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) (3) All timing parameters are described in Tables 32 through 38 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. Tables 99 through 105 show EPF10K100A device internal and external timing parameters. Table 99. EPF10K100A Device LE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 1.0 1.2 1.4 ns tCLUT 0.8 0.9 1.1 ns tRLUT 1.4 1.6 1.9 ns tPACKED 0.4 0.5 0.5 ns tEN 0.6 0.7 0.8 ns tCICO 0.2 0.2 0.3 ns tCGEN 0.4 0.4 0.6 ns tCGENR 0.6 0.7 0.8 ns tCASC 0.7 0.9 1.0 ns tC 0.9 1.0 1.2 ns tCO 0.2 0.3 0.3 ns 0.8 ns 0.6 tCOMB tSU 0.8 tH 0.3 0.7 1.0 1.2 0.5 ns 0.5 ns tPRE 0.3 0.3 0.4 ns tCLR 0.3 0.3 0.4 ns tCH 2.5 3.5 4.0 ns tCL 2.5 3.5 4.0 ns Altera Corporation 109 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 100. EPF10K100A Device IOE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 2.5 2.9 3.4 ns tIOC 0.3 0.3 0.4 ns tIOCO 0.2 0.2 0.3 ns tIOCOMB 0.5 0.6 0.7 ns tIOSU 1.3 tIOH 0.2 1.7 1.8 0.2 ns 0.3 ns tIOCLR 1.0 1.2 1.4 ns tOD1 2.2 2.6 3.0 ns tOD2 4.5 5.3 6.1 ns tOD3 6.8 7.9 9.3 ns tXZ 2.7 3.1 3.7 ns tZX1 2.7 3.1 3.7 ns tZX2 5.0 5.8 6.8 ns tZX3 7.3 8.4 10.0 ns tINREG 5.3 6.1 7.2 ns tIOFD 4.7 5.5 6.4 ns tINCOMB 4.7 5.5 6.4 ns 110 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 101. EPF10K100A Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.8 2.1 2.4 ns tEABDATA2 3.2 3.7 4.4 ns tEABWE1 0.8 0.9 1.1 ns tEABWE2 2.3 2.7 3.1 ns tEABCLK 0.8 0.9 1.1 ns tEABCO 1.0 1.1 1.4 ns tEABBYPASS 0.3 0.3 0.4 ns tEABSU 1.3 1.5 1.8 ns tEABH 0.4 0.5 0.5 ns 4.1 tAA 4.8 5.6 ns tWP 3.2 3.7 4.4 ns tWDSU 2.4 2.8 3.3 ns tWDH 0.2 0.2 0.3 ns tWASU 0.2 0.2 0.3 ns tWAH 0.0 0.0 0.0 ns tWO 3.4 3.9 4.6 ns tDD 3.4 3.9 4.6 ns 0.4 ns 0.3 tEABOUT 0.3 tEABCH 2.5 3.5 4.0 ns tEABCL 3.2 3.7 4.4 ns Altera Corporation 111 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 102. EPF10K100A Device EAB Internal Timing Macroparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 6.8 Max 7.8 Unit Max 9.2 ns tEABRCCOMB 6.8 7.8 9.2 ns tEABRCREG 5.4 6.2 7.4 ns tEABWP 3.2 3.7 4.4 ns tEABWCCOMB 3.4 3.9 4.7 ns tEABWCREG 9.4 tEABDD 10.8 6.1 2.1 tEABDATACO 12.8 6.9 ns 8.2 2.3 2.9 ns ns tEABDATASU 3.7 4.3 5.1 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 2.8 3.3 3.8 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 3.4 4.0 4.6 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 1.9 2.3 2.6 ns tEABWAH 0.0 0.0 0.0 tEABWO 112 5.1 5.7 ns 6.9 ns Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 103. EPF10K100A Device Interconnect Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tDIN2IOE 4.8 5.4 6.0 ns tDIN2LE 2.0 2.4 2.7 ns tDIN2DATA 2.4 2.7 2.9 ns tDCLK2IOE 2.6 3.0 3.5 ns tDCLK2LE 2.0 2.4 2.7 ns tSAMELAB 0.1 0.1 0.1 ns tSAMEROW 1.5 1.7 1.9 ns tSAMECOLUMN 5.5 6.5 7.4 ns tDIFFROW 7.0 8.2 9.3 ns tTWOROWS 8.5 9.9 11.2 ns tLEPERIPH 3.9 4.2 4.5 ns tLABCARRY 0.2 0.2 0.3 ns tLABCASC 0.4 0.5 0.6 ns Table 104. EPF10K100A Device External Timing Parameters Symbol -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max tDRR Max 12.5 tINSU (2), (3) Note (1) tINH (3) 0.0 tOUTCO (3) 2.0 17.0 4.5 0.0 5.3 ns 5.1 ns 0.0 2.0 6.1 ns 2.0 Table 105. EPF10K100A Device External Bidirectional Timing Parameters Symbol Max 14.5 3.7 Unit 7.2 ns Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tINSUBIDIR 4.9 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max Max 5.8 2.0 Max 6.8 0.0 5.3 ns 0.0 6.1 2.0 Unit ns 7.2 ns tXZBIDIR 7.4 8.6 10.1 ns tZXBIDIR 7.4 8.6 10.1 ns Altera Corporation 113 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) (3) All timing parameters are described in Tables 32 through 38 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. Tables 106 through 112 show EPF10K250A device internal and external timing parameters. Table 106. EPF10K250A Device LE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.9 1.0 1.4 ns tCLUT 1.2 1.3 1.6 ns tRLUT 2.0 2.3 2.7 ns tPACKED 0.4 0.4 0.5 ns tEN 1.4 1.6 1.9 ns tCICO 0.2 0.3 0.3 ns tCGEN 0.4 0.6 0.6 ns tCGENR 0.8 1.0 1.1 ns tCASC 0.7 0.8 1.0 ns tC 1.2 1.3 1.6 ns tCO 0.6 0.7 0.9 ns 0.7 ns 0.5 tCOMB tSU 1.2 tH 1.2 0.6 1.4 1.7 1.3 ns 1.6 ns tPRE 0.7 0.8 0.9 ns tCLR 0.7 0.8 0.9 ns tCH 2.5 3.0 3.5 ns tCL 2.5 3.0 3.5 ns 114 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 107. EPF10K250A Device IOE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 1.2 1.3 1.6 ns tIOC 0.4 0.4 0.5 ns tIOCO 0.8 0.9 1.1 ns tIOCOMB 0.7 0.7 0.8 ns tIOSU 2.7 tIOH 0.2 3.1 3.6 0.3 ns 0.3 ns tIOCLR 1.2 1.3 1.6 ns tOD1 3.2 3.6 4.2 ns tOD2 5.9 6.7 7.8 ns tOD3 8.7 9.8 11.5 ns tXZ 3.8 4.3 5.0 ns tZX1 3.8 4.3 5.0 ns tZX2 6.5 7.4 8.6 ns tZX3 9.3 10.5 12.3 ns tINREG 8.2 9.3 10.9 ns tIOFD 9.0 10.2 12.0 ns tINCOMB 9.0 10.2 12.0 ns Altera Corporation 115 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 108. EPF10K250A Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.3 1.5 1.7 ns tEABDATA2 1.3 1.5 1.7 ns tEABWE1 0.9 1.1 1.3 ns tEABWE2 5.0 5.7 6.7 ns tEABCLK 0.6 0.7 0.8 ns tEABCO 0.0 0.0 0.0 ns tEABBYPASS 0.1 0.1 0.2 ns tEABSU 3.8 4.3 5.0 ns tEABH 0.7 0.8 0.9 ns 4.5 tAA 5.0 5.9 ns tWP 5.6 6.4 7.5 ns tWDSU 1.3 1.4 1.7 ns tWDH 0.1 0.1 0.2 ns tWASU 0.1 0.1 0.2 ns tWAH 0.1 0.1 0.2 ns tWO 4.1 4.6 5.5 ns tDD 4.1 4.6 5.5 ns 0.2 ns 0.1 tEABOUT 0.1 tEABCH 2.5 3.0 3.5 ns tEABCL 5.6 6.4 7.5 ns 116 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 109. EPF10K250A Device EAB Internal Timing Macroparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 6.1 Max 6.8 Unit Max 8.2 ns tEABRCCOMB 6.1 6.8 8.2 ns tEABRCREG 4.6 5.1 6.1 ns tEABWP 5.6 6.4 7.5 ns tEABWCCOMB 5.8 6.6 7.9 ns tEABWCREG 15.8 tEABDD 17.8 5.7 0.7 tEABDATACO 21.0 6.4 0.8 ns 7.8 ns 1.0 ns tEABDATASU 4.5 5.1 tEABDATAH 0.0 0.0 0.0 ns tEABWESU 8.2 9.3 10.9 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 1.7 1.8 2.1 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 0.9 0.9 1.0 ns tEABWAH 0.0 0.0 0.0 tEABWO Altera Corporation 5.3 5.9 6.0 ns ns 7.4 ns 117 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 110. EPF10K250A Device Interconnect Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tDIN2IOE 7.8 8.5 9.4 ns tDIN2LE 2.7 3.1 3.5 ns tDIN2DATA 1.6 1.6 1.7 ns tDCLK2IOE 3.6 4.0 4.6 ns tDCLK2LE 2.7 3.1 3.5 ns tSAMELAB 0.2 0.3 0.3 ns tSAMEROW 6.7 7.3 8.2 ns tSAMECOLUMN 2.5 2.7 3.0 ns tDIFFROW 9.2 10.0 11.2 ns tTWOROWS 15.9 17.3 19.4 ns tLEPERIPH 7.5 8.1 8.9 ns tLABCARRY 0.3 0.4 0.5 ns tLABCASC 0.4 0.4 0.5 ns Table 111. EPF10K250A Device External Reference Timing Parameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max tDRR Max 15.0 tINSU (2), (3) 6.9 tINH (3) 0.0 tOUTCO (3) 2.0 20.0 0.0 Min tINSUBIDIR 9.3 tINHBIDIR 0.0 tOUTCOBIDIR 2.0 Max 8.9 -2 Speed Grade Min Max 10.4 ns Note (1) -3 Speed Grade Min ns 0.0 8.9 2.0 Unit Max 12.7 0.0 2.0 ns 2.0 10.6 8.0 ns 0.0 2.0 -1 Speed Grade ns 9.4 Table 112. EPF10K250A Device External Bidirectional Timing Parameters Symbol Max 17.0 8.0 8.0 Unit ns 10.4 ns tXZBIDIR 10.8 12.2 14.2 ns tZXBIDIR 10.8 12.2 14.2 ns 118 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes to tables: (1) (2) (3) All timing parameters are described in Tables 32 through 37 in this data sheet. Using an LE to register the signal may provide a lower setup time. This parameter is specified by characterization. ClockLock & ClockBoost Timing Parameters For the ClockLock and ClockBoost circuitry to function properly, the incoming clock must meet certain requirements. If these specifications are not met, the circuitry may not lock onto the incoming clock, which generates an erroneous clock within the device. The clock generated by the ClockLock and ClockBoost circuitry must also meet certain specifications. If the incoming clock meets these requirements during configuration, the ClockLock and ClockBoost circuitry will lock onto the clock during configuration. The circuit will be ready for use immediately after configuration. Figure 31 illustrates the incoming and generated clock specifications. Figure 31. Specifications for the Incoming & Generated Clocks The tI parameter refers to the nominal input clock period; the tO parameter refers to the nominal output clock period. tCLK1 tINDUTY tI fCLKDEV Input Clock tR tF tI tI tINCLKSTB tO tO + tJITTER tOUTDUTY ClockLockGenerated Clock tO - tJITTER Table 113 summarizes the ClockLock and ClockBoost parameters. Table 113. ClockLock & ClockBoost Parameters Symbol tR (Part 1 of 2) Parameter Min Input rise time Typ Max Unit 2 ns 2 ns tF Input fall time t INDUTY Input duty cycle 45 55 % f CLK1 Input clock frequency (ClockBoost clock multiplication factor equals 1) 30 80 MHz t CLK1 Input clock period (ClockBoost clock multiplication factor equals 1) 12.5 33.3 ns fCLK2 Input clock frequency (ClockBoost clock multiplication factor equals 2) 16 50 MHz tCLK2 Input clock period (ClockBoost clock multiplication factor equals 2) 20 62.5 ns Altera Corporation 119 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Table 113. ClockLock & ClockBoost Parameters Symbol (Part 2 of 2) Parameter Max Unit f CLKDEV1 Input deviation from user specification in MAX+PLUS II (ClockBoost clock multiplication factor equals 1) (1) 1 MHz f CLKDEV2 Input deviation from user specification in MAX+PLUS II (ClockBoost clock multiplication factor equals 2) (1) 0.5 MHz t INCLKSTB Input clock stability (measured between adjacent clocks) 100 ps 10 s 1 ns 60 % t LOCK Time required for ClockLock or ClockBoost to acquire lock (2) t JITTER Jitter on ClockLock or ClockBoost-generated clock (3) Min tOUTDUTY Duty cycle for ClockLock or ClockBoost-generated clock 40 Typ 50 Notes: (1) (2) (3) To implement the ClockLock and ClockBoost circuitry with the MAX+PLUS II software, designers must specify the input frequency. The MAX+PLUS II software tunes the PLL in the ClockLock and ClockBoost circuitry to this frequency. The f CLKDEV parameter specifies how much the incoming clock can differ from the specified frequency during device operation. Simulation does not reflect this parameter. During device configuration, the ClockLock and ClockBoost circuitry is configured before the rest of the device. If the incoming clock is supplied during configuration, the ClockLock and ClockBoost circuitry locks during configuration, because the tLOCK value is less than the time required for configuration. The tJITTER specification is measured under long-term observation. Power Consumption The supply power (P) for FLEX 10K devices can be calculated with the following equation: P = PINT + PIO = (I CCSTANDBY + ICCACTIVE) x VCC + PIO Typical I CCSTANDBY values are shown as I CC0 in the FLEX 10K device DC operating conditions tables on pages 46, 49, and 52 of this data sheet. The ICCACTIVE value depends on the switching frequency and the application logic. This value is calculated based on the amount of current that each LE typically consumes. The PIO value, which depends on the device output load characteristics and switching frequency, can be calculated using the guidelines given in Application Note 74 (Evaluating Power for Altera Devices). 1 Compared to the rest of the device, the embedded array consumes a negligible amount of power. Therefore, the embedded array can be ignored when calculating supply current. The ICCACTIVE value is calculated with the following equation: A ICCACTIVE = K x fMAX x N x togLC x --------------------------MHz x LE The parameters in this equation are shown below: 120 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet fMAX N togLC = = = K = Maximum operating frequency in MHz Total number of logic cells used in the device Average percent of logic cells toggling at each clock (typically 12.5%) Constant, shown in Tables 114 and 115 Table 114. FLEX 10K K Constant Values Device K Value EPF10K10 82 EPF10K20 89 EPF10K30 88 EPF10K40 92 EPF10K50 95 EPF10K70 85 EPF10K100 88 Table 115. FLEX 10KA K Constant Values Device K Value EPF10K10A 17 EPF10K30A 17 EPF10K50V 19 EPF10K100A 19 EPF10K130V 22 EPF10K250A 23 This calculation provides an ICC estimate based on typical conditions with no output load. The actual ICC should be verified during operation because this measurement is sensitive to the actual pattern in the device and the environmental operating conditions. To better reflect actual designs, the power model (and the constant K in the power calculation equations) for continuous interconnect FLEX devices assumes that logic cells drive FastTrack Interconnect channels. In contrast, the power model of segmented FPGAs assumes that all logic cells drive only one short interconnect segment. This assumption may lead to inaccurate results, compared to measured power consumption for an actual design in a segmented interconnect FPGA. Figure 32 shows the relationship between the current and operating frequency of FLEX 10K devices. Altera Corporation 121 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 32. ICCACTIVE vs. Operating Frequency (Part 1 of 3) EPF10K10 ICC Supply Current (mA) EPF10K20 500 1,000 450 900 400 800 350 700 300 ICC Supply Current (mA) 250 600 500 200 400 150 300 100 200 50 100 0 30 15 45 0 60 15 30 45 60 45 60 45 60 Frequency (MHz) Frequency (MHz) EPF10K40 EPF10K30 1,600 2,500 1,400 2,000 1,200 ICC Supply Current (mA) 1,000 ICC Supply Current (mA) 800 600 1,500 1,000 400 200 500 0 15 30 45 0 60 15 Frequency (MHz) 30 Frequency (MHz) EPF10K70 EPF10K50 3,000 3,500 3,000 2,500 2,500 2,000 ICC Supply Current (mA) ICC Supply Current (mA) 1,500 2,000 1,500 1,000 1,000 500 500 0 15 30 Frequency (MHz) 122 45 60 0 15 30 Frequency (MHz) Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 32. ICCACTIVE vs. Operating Frequency (Part 2 of 3) EPF10K50V EPF10K100 700 4,500 600 4,000 3,500 500 3,000 ICC Supply Current (mA) ICC Supply Current (mA) 2,500 400 2,000 300 1,500 200 1,000 100 500 0 0 45 30 15 60 20 EPF10K130V 40 60 80 100 Frequency (MHz) Frequency (MHz) EPF10K10A 150 2,000 1,500 ICC Supply Current (mA) 100 ICC Supply Current (mA) 1,000 50 500 0 20 40 60 80 100 0 Frequency (MHz) 75 50 25 100 Frequency (MHz) EPF10K30A EPF10K100A 1,200 400 900 300 ICC Supply Current (mA) ICC Supply Current (mA) 200 600 300 100 0 0 25 50 75 Frequency (MHz) Altera Corporation 100 20 40 60 80 100 Frequency (MHz) 123 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Figure 32. ICCACTIVE vs. Operating Frequency (Part 3 of 3) EPF10K250A 3,500 3,000 2,500 ICC Supply Current (mA) 2,000 1,500 1,000 500 0 20 40 60 80 100 Frequency (MHz) Configuration & Operation The FLEX 10K architecture supports several configuration schemes. This section summarizes the device operating modes and available device configuration schemes. f See Application Note 116 (Configuring APEX 20K, FLEX 10K & FLEX 6000 Devices) for detailed descriptions of device configuration options, device configuration pins, and for information on configuring FLEX 10K devices, including sample schematics, timing diagrams, and configuration parameters. Operating Modes The FLEX 10K architecture uses SRAM configuration elements that require configuration data to be loaded every time the circuit powers up. The process of physically loading the SRAM data into the device is called configuration. Before configuration, as VCC rises, the device initiates a Power-On Reset (POR). This POR event clears the device and prepares it for configuration. The FLEX 10K POR time does not exceed 50 s. During initialization, which occurs immediately after configuration, the device resets registers, enables I/O pins, and begins to operate as a logic device. The I/O pins are tri-stated during power-up, and before and during configuration. Together, the configuration and initialization processes are called command mode; normal device operation is called user mode. 124 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet SRAM configuration elements allow FLEX 10K devices to be reconfigured in-circuit by loading new configuration data into the device. Real-time reconfiguration is performed by forcing the device into command mode with a device pin, loading different configuration data, reinitializing the device, and resuming user-mode operation. The entire reconfiguration process may be completed in less than 320 ms using an EPF10K250A device with a DCLK frequency of 10 MHz. This process can be used to reconfigure an entire system dynamically. In-field upgrades can be performed by distributing new configuration files. 1 Refer to the configuration device data sheet to obtain the POR delay when using a configuration device method. Programming Files Despite being function- and pin-compatible, FLEX 10KA and FLEX 10KE devices are not programming- or configuration-file compatible with FLEX 10K devices. A design should be recompiled before it is transferred from a FLEX 10K device to an equivalent FLEX 10KA or FLEX 10KE device. This recompilation should be performed to create a new programming or configuration file and to check design timing on the faster FLEX 10KA or FLEX 10KE device. The programming or configuration files for EPF10K50 devices can program or configure an EPF10K50V device. However, Altera recommends recompiling a design for the EPF10K50V device when transferring it from the EPF10K50 device. Configuration Schemes The configuration data for a FLEX 10K device can be loaded with one of five configuration schemes (see Table 116), chosen on the basis of the target application. An EPC1, EPC2, EPC16, or EPC1441 configuration device, intelligent controller, or the JTAG port can be used to control the configuration of a FLEX 10K device, allowing automatic configuration on system power-up. Altera Corporation 125 FLEX 10K Embedded Programmable Logic Device Family Data Sheet Multiple FLEX 10K devices can be configured in any of the five configuration schemes by connecting the configuration enable (nCE) and configuration enable output (nCEO) pins on each device. Table 116. Data Sources for Configuration Configuration Scheme Data Source Configuration device EPC1, EPC2, EPC16, or EPC1441 configuration device Passive serial (PS) BitBlaster, MasterBlaster, or ByteBlasterMV download cable, or serial data source Passive parallel asynchronous (PPA) Parallel data source Passive parallel synchronous (PPS) Parallel data source JTAG BitBlaster, MasterBlaster, or ByteBlasterMV download cable, or microprocessor with Jam STAPL file or Jam Byte-Code file Device PinOuts See the Altera web site (http://www.altera.com) or the Altera Digital Library for pin-out information. Revision History The information contained in the FLEX 10K Embedded Programmable Logic Device Family Data Sheet version 4.1 supersedes information published in previous versions. Version 4.1 Changes 126 Updated General Description section Updated I/O Element section Updated SameFrame Pin-Outs section Updated Figure 16 Updated Tables 13 and 116 Added Note 9 to Table 19 Added Note 10 to Table 24 Added Note 10 to Table 28 Altera Corporation FLEX 10K Embedded Programmable Logic Device Family Data Sheet Notes: Altera Corporation 127 FLEX 10K Embedded Programmable Logic Device Family Data Sheet (R) 101 Innovation Drive San Jose, CA 95134 (408) 544-7000 http://www.altera.com Applications Hotline: (800) 800-EPLD Customer Marketing: (408) 544-7104 Literature Services: (lit_req@altera.com Altera, BitBlaster, ByteBlaster, ByteBlasterMV, ClockLock, ClockBoost, EPF10K10, EPF10K10A, EPF10K20, EPF10K30, EPF10K30A, EPF10K40, EPF10K50, EPF10K50V, EPF10K70, EPF10K100, EPF10K100A, EPF10K130V, EPF10K250A, FastTrack, FineLine BGA, FLEX, FLEX 10K, FLEX 10KA, FLEX 10KE, MAX, MAX+PLUS, MAX+PLUS II, MultiVolt, Quartus, and Quartus II are trademarks and/or service marks of Altera Corporation in the United States and other countries. Altera products are protected under numerous U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera Corporation. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services Copyright 2001 Altera Corporation. All rights reserved. 128 Altera Corporation Printed on Recycled Paper. Altera Part Number Search Results GO Advanced Results for: EPF10K* Help 296 part numbers found and 33 obsolete part numbers found FLEX 10K Device Family (5.0V) FLEX 10K/A Datasheet Part Number Format FLEX 10K Literature Buying Altera Devices Part Number Device EPF10K10LC84-3 EPF10K10LC84-4 EPF10K10 84 pin PLCC Pinout Commercial ( 0 to 85C) EPF10K10LI84-4 EPF10K10 84 pin PLCC Pinout Industrial -4 ( -40 to 100C) None EPF10K10QC208-3 EPF10K10QC208-4 EPF10K10 208 pin PQFP Pinout Commercial ( 0 to 85C) None EPF10K10QI208-4 EPF10K10 208 pin PQFP Pinout Industrial -4 ( -40 to 100C) None EPF10K10TC144-3 EPF10K10TC144-4 EPF10K10 144 pin TQFP Pinout Commercial ( 0 to 85C) None EPF10K10TI144-4 EPF10K10 144 pin TQFP Pinout Industrial -4 ( -40 to 100C) None EPF10K20RC208-3 EPF10K20RC208-4 EPF10K20 208 pin RQFP Pinout Commercial ( 0 to 85C) None file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (1 of 15) [2/11/03 5:07:36 PM] Pins & Package Temperature Speeds Options -3, -4 -3, -4 -3, -4 -3, -4 None Altera Part Number Search Results EPF10K20RC240-3 EPF10K20RC240-4 EPF10K20 240 pin RQFP Pinout Commercial ( 0 to 85C) EPF10K20RI208-4 EPF10K20 208 pin RQFP Pinout Industrial -4 ( -40 to 100C) None EPF10K20RI240-4 EPF10K20 240 pin RQFP Pinout Industrial -4 ( -40 to 100C) None EPF10K20TC144-3 EPF10K20TC144-4 EPF10K20 144 pin TQFP Pinout Commercial ( 0 to 85C) None EPF10K20TI144-4 EPF10K20 144 pin TQFP Pinout Industrial -4 ( -40 to 100C) None EPF10K30BC356-3 EPF10K30BC356-4 EPF10K30 356 pin BGA Pinout Commercial ( 0 to 85C) -3, -4 None EPF10K30RC208-3 EPF10K30RC208-4 EPF10K30 208 pin RQFP Pinout Commercial ( 0 to 85C) -3, -4 None EPF10K30RC240-3 EPF10K30RC240-4 EPF10K30 240 pin RQFP Pinout Commercial ( 0 to 85C) -3, -4 None EPF10K30RI208-4 EPF10K30 208 pin RQFP Pinout Industrial -4 ( -40 to 100C) None EPF10K30RI240-4 EPF10K30 240 pin RQFP Pinout Industrial -4 ( -40 to 100C) None EPF10K40RC208-3 EPF10K40RC208-4 EPF10K40 208 pin RQFP Pinout Commercial ( 0 to 85C) -3, -4 None EPF10K40RC240-3 EPF10K40RC240-4 EPF10K40 240 pin RQFP Pinout Commercial ( 0 to 85C) -3, -4 None EPF10K50BC356-3 EPF10K50BC356-4 EPF10K50 356 pin BGA Pinout Commercial ( 0 to 85C) -3, -4 None EPF10K50GC403-3 EPF10K50GC403-4 EPF10K50 403 pin PGA Pinout Commercial ( 0 to 85C) -3, -4 None file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (2 of 15) [2/11/03 5:07:36 PM] -3, -4 -3, -4 None Altera Part Number Search Results EPF10K50RC240-3 EPF10K50RC240-4 EPF10K50 240 pin RQFP Pinout Commercial ( 0 to 85C) EPF10K50RI240-4 EPF10K50 240 pin RQFP Pinout Industrial -4 ( -40 to 100C) None EPF10K70GC503-3 EPF10K70GC503-4 EPF10K70 503 pin PGA Pinout Commercial ( 0 to 85C) -3, -4 None EPF10K70RC240-2 EPF10K70RC240-3 EPF10K70RC240-4 EPF10K70 240 pin RQFP Pinout Commercial ( 0 to 85C) -2, -3, -4 None Commercial ( 0 to 85C) -3, -4 EPF10K100GC503-3 EPF10K100 503 pin PGA Pinout EPF10K100GC503-3DX EPF10K100GC503-4 -3, -4 None DX: Has PLLs FLEX 10KA Device Family (3.3V) FLEX 10K/A Datasheet Part Number Format FLEX 10K Literature Buying Altera Devices Part Number Device Speeds Options EPF10K10AFC256-1 EPF10K10AFC256-2 EPF10K10AFC256-3 EPF10K10A 256 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K10AQC208-1 EPF10K10AQC208-2 EPF10K10AQC208-3 EPF10K10A 208 pin PQFP Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K10AQI208-3 EPF10K10A 208 pin PQFP Pinout Industrial -3 ( -40 to 100C) None EPF10K10ATC100-1 EPF10K10ATC100-2 EPF10K10ATC100-3 EPF10K10A 100 pin TQFP Pinout Commercial ( 0 to 85C) None file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (3 of 15) [2/11/03 5:07:36 PM] Pins & Package Temperature -1, -2, -3 Altera Part Number Search Results EPF10K10ATC144-1 EPF10K10ATC144-2 EPF10K10ATC144-3 EPF10K10A 144 pin TQFP Pinout Commercial ( 0 to 85C) EPF10K10ATI144-3 EPF10K10A 144 pin TQFP Pinout Industrial -3 ( -40 to 100C) None EPF10K30ABC356-1 EPF10K30ABC356-2 EPF10K30ABC356-3 EPF10K30A 356 pin BGA Pinout Commercial ( 0 to 85C) None EPF10K30ABI356-3 EPF10K30A 356 pin BGA Pinout Industrial -3 ( -40 to 100C) None EPF10K30AFC256-1 EPF10K30AFC256-2 EPF10K30AFC256-3 EPF10K30A 256 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K30AFC484-1 EPF10K30AFC484-2 EPF10K30AFC484-3 EPF10K30A 484 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K30AFI256-2 EPF10K30A 256 pin FBGA Pinout Industrial -2 ( -40 to 100C) None EPF10K30AQC208-1 EPF10K30AQC208-2 EPF10K30AQC208-3 EPF10K30A 208 pin PQFP Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K30AQC240-1 EPF10K30AQC240-2 EPF10K30AQC240-3 EPF10K30A 240 pin PQFP Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K30AQI208-3 EPF10K30A 208 pin PQFP Pinout Industrial -3 ( -40 to 100C) None EPF10K30AQI240-3 EPF10K30A 240 pin PQFP Pinout Industrial -3 ( -40 to 100C) None EPF10K30ATC144-1 EPF10K30ATC144-2 EPF10K30ATC144-3 EPF10K30A 144 pin TQFP Pinout Commercial ( 0 to 85C) None file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (4 of 15) [2/11/03 5:07:36 PM] -1, -2, -3 -1, -2, -3 -1, -2, -3 None Altera Part Number Search Results EPF10K30ATI144-3 EPF10K30A 144 pin TQFP Pinout Industrial -3 ( -40 to 100C) EPF10K50VBC356-1 EPF10K50VBC356-2 EPF10K50VBC356-3 EPF10K50VBC356-4 EPF10K50V 356 pin BGA Pinout Commercial ( 0 to 85C) EPF10K50VBI356-3 EPF10K50VBI356-4 EPF10K50V 356 pin BGA Pinout Industrial -3, -4 ( -40 to 100C) None EPF10K50VFC484-1 EPF10K50VFC484-2 EPF10K50VFC484-3 EPF10K50V 484 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K50VQC240-1 EPF10K50VQC240-2 EPF10K50VQC240-3 EPF10K50V 240 pin PQFP Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K50VQI240-2 EPF10K50V 240 pin PQFP Pinout Industrial -2 ( -40 to 100C) EPF10K50VRC240-1 EPF10K50VRC240-2 EPF10K50VRC240-3 EPF10K50VRC240-4 EPF10K50V 240 pin RQFP Pinout Commercial ( 0 to 85C) EPF10K50VRI240-3 EPF10K50VRI240-4 EPF10K50V 240 pin RQFP Pinout Industrial -3, -4 ( -40 to 100C) None EPF10K100ABC356-1 EPF10K100A 356 pin BGA EPF10K100ABC356-2 Pinout EPF10K100ABC356-3 Commercial ( 0 to 85C) -1, -2, -3 None EPF10K100ABC600-1 EPF10K100A 600 pin BGA Pinout EPF10K100ABC600-2 EPF10K100ABC600-3 Commercial ( 0 to 85C) -1, -2, -3 None EPF10K100ABI356-2 EPF10K100ABI356-3 EPF10K100A 356 pin BGA Pinout file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (5 of 15) [2/11/03 5:07:36 PM] None -1, -2, -3, -4 None None -1, -2, -3, -4 None Industrial -2, -3 ( -40 to 100C) None Altera Part Number Search Results EPF10K100ABI600-2 EPF10K100A 600 pin BGA Pinout Industrial -2 ( -40 to 100C) None EPF10K100AFC484-1 EPF10K100A 484 pin FBGA EPF10K100AFC484-2 Pinout EPF10K100AFC484-3 Commercial ( 0 to 85C) -1, -2, -3 None EPF10K100ARC240-1 EPF10K100A 240 pin RQFP Pinout EPF10K100ARC240-2 EPF10K100ARC240-3 Commercial ( 0 to 85C) -1, -2, -3 None Industrial -3 ( -40 to 100C) None EPF10K130VBC600-2 EPF10K130V 600 pin BGA EPF10K130VBC600-3 Pinout EPF10K130VBC600-4 Commercial ( 0 to 85C) -2, -3, -4 None EPF10K130VGC599-2 EPF10K130V 599 pin PGA Pinout EPF10K130VGC599-3 EPF10K130VGC599-4 Commercial ( 0 to 85C) -2, -3, -4 None EPF10K250ABC600-1 EPF10K250A 600 pin BGA Pinout EPF10K250ABC600-2 EPF10K250ABC600-3 Commercial ( 0 to 85C) -1, -2, -3 None EPF10K250AGC599-1 EPF10K250A 599 pin PGA Pinout EPF10K250AGC599-2 EPF10K250AGC599-3 Commercial ( 0 to 85C) -1, -2, -3 None EPF10K100ARI240-3 EPF10K100A 240 pin RQFP Pinout FLEX 10KE Device Family (2.5V) FLEX 10KE Datasheet Part Number Format Part Number FLEX 10K Literature Buying Altera Devices Device file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (6 of 15) [2/11/03 5:07:36 PM] Pins & Package Temperature Speeds Options Altera Part Number Search Results EPF10K30EFC256-1 EPF10K30EFC256-1X EPF10K30EFC256-2 EPF10K30EFC256-2X EPF10K30EFC256-3 EPF10K30E 256 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K30EFC484-1 EPF10K30EFC484-1X EPF10K30EFC484-2 EPF10K30EFC484-2X EPF10K30EFC484-3 EPF10K30E 484 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K30EFI256-2 EPF10K30E 256 pin FBGA Pinout Industrial -2 ( -40 to 100C) EPF10K30EQC208-1 EPF10K30EQC208-1X EPF10K30EQC208-2 EPF10K30EQC208-2X EPF10K30EQC208-3 EPF10K30E 208 pin PQFP Pinout Commercial ( 0 to 85C) EPF10K30EQI208-2 EPF10K30E 208 pin PQFP Pinout Industrial -2 ( -40 to 100C) EPF10K30ETC144-1 EPF10K30ETC144-1X EPF10K30ETC144-2 EPF10K30ETC144-2X EPF10K30ETC144-3 EPF10K30E 144 pin TQFP Pinout Commercial ( 0 to 85C) EPF10K30ETI144-2 EPF10K30E 144 pin TQFP Pinout Industrial -2 ( -40 to 100C) EPF10K50EFC256-1 EPF10K50EFC256-2 EPF10K50EFC256-3 EPF10K50E 256 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K50EFC484-1 EPF10K50EFC484-2 EPF10K50EFC484-3 EPF10K50E 484 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (7 of 15) [2/11/03 5:07:36 PM] None -1, -2, -3 X: Has PLLs None -1, -2, -3 X: Has PLLs None Altera Part Number Search Results EPF10K50EFI256-2 EPF10K50E 256 pin FBGA Pinout Industrial -2 ( -40 to 100C) EPF10K50EQC208-1 EPF10K50EQC208-2 EPF10K50EQC208-3 EPF10K50E 208 pin PQFP Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K50EQC240-1 EPF10K50EQC240-2 EPF10K50EQC240-3 EPF10K50E 240 pin PQFP Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K50EQI240-2 EPF10K50E 240 pin PQFP Pinout Industrial -2 ( -40 to 100C) EPF10K50ETC144-1 EPF10K50ETC144-2 EPF10K50ETC144-3 EPF10K50E 144 pin TQFP Pinout Commercial ( 0 to 85C) EPF10K50ETI144-2 EPF10K50E 144 pin TQFP Pinout Industrial -2 ( -40 to 100C) EPF10K50SBC356-1 EPF10K50SBC356-1X EPF10K50SBC356-2 EPF10K50SBC356-2X EPF10K50SBC356-3 EPF10K50S 356 pin BGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K50SFC256-1 EPF10K50SFC256-1X EPF10K50SFC256-2 EPF10K50SFC256-2X EPF10K50SFC256-3 EPF10K50S 256 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K50SFC484-1 EPF10K50SFC484-1X EPF10K50SFC484-2 EPF10K50SFC484-2X EPF10K50SFC484-3 EPF10K50S 484 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K50SFI484-2 EPF10K50S 484 pin FBGA Pinout Industrial -2 ( -40 to 100C) file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (8 of 15) [2/11/03 5:07:36 PM] None None -1, -2, -3 None None None Altera Part Number Search Results EPF10K50SQC208-1 EPF10K50SQC208-1X EPF10K50SQC208-2 EPF10K50SQC208-2X EPF10K50SQC208-3 EPF10K50S 208 pin PQFP Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K50SQC240-1 EPF10K50SQC240-1X EPF10K50SQC240-2 EPF10K50SQC240-2X EPF10K50SQC240-3 EPF10K50S 240 pin PQFP Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K50SQI208-2 EPF10K50S 208 pin PQFP Pinout Industrial -2 ( -40 to 100C) EPF10K50STC144-1 EPF10K50STC144-1X EPF10K50STC144-2 EPF10K50STC144-2X EPF10K50STC144-3 EPF10K50S 144 pin TQFP Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100EBC356-1 EPF10K100E 356 pin BGA EPF10K100EBC356-1X Pinout EPF10K100EBC356-2 EPF10K100EBC356-2X EPF10K100EBC356-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100EFC256-1 EPF10K100E 256 pin FBGA Pinout EPF10K100EFC256-1X EPF10K100EFC256-2 EPF10K100EFC256-2X EPF10K100EFC256-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100E 484 pin FBGA EPF10K100EFC484-1 Pinout EPF10K100EFC484-1X EPF10K100EFC484-2 EPF10K100EFC484-2X EPF10K100EFC484-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (9 of 15) [2/11/03 5:07:36 PM] None Altera Part Number Search Results EPF10K100EFI256-2 EPF10K100E 256 pin FBGA Pinout Industrial -2 ( -40 to 100C) None EPF10K100EFI484-2 EPF10K100E 484 pin FBGA Pinout Industrial -2 ( -40 to 100C) None EPF10K100EQC208-1 EPF10K100E 208 pin PQFP EPF10K100EQC208-1X Pinout EPF10K100EQC208-2 EPF10K100EQC208-2X EPF10K100EQC208-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100EQC240-1 EPF10K100E 240 pin PQFP EPF10K100EQC240-1X Pinout EPF10K100EQC240-2 EPF10K100EQC240-2X EPF10K100EQC240-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100EQI208-2 EPF10K100E 208 pin PQFP Pinout Industrial -2 ( -40 to 100C) None EPF10K100EQI240-2 EPF10K100E 240 pin PQFP Pinout Industrial -2 ( -40 to 100C) None EPF10K130EBC356-1 EPF10K130E 356 pin BGA EPF10K130EBC356-1X Pinout EPF10K130EBC356-2 EPF10K130EBC356-2X EPF10K130EBC356-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K130EBC600-1 EPF10K130E 600 pin BGA EPF10K130EBC600-1X Pinout EPF10K130EBC600-2 EPF10K130EBC600-2X EPF10K130EBC600-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K130EBI356-2 EPF10K130E 356 pin BGA Pinout file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (10 of 15) [2/11/03 5:07:36 PM] Industrial -2 ( -40 to 100C) None Altera Part Number Search Results EPF10K130EFC484-1 EPF10K130E 484 pin FBGA EPF10K130EFC484-1X Pinout EPF10K130EFC484-2 EPF10K130EFC484-2X EPF10K130EFC484-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K130EFC672-1 EPF10K130E 672 pin FBGA EPF10K130EFC672-1X Pinout EPF10K130EFC672-2 EPF10K130EFC672-2X EPF10K130EFC672-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K130EFI484-2 EPF10K130E 484 pin FBGA Pinout EPF10K130EQC240-1 EPF10K130E 240 pin PQFP EPF10K130EQC240-1X Pinout EPF10K130EQC240-2 EPF10K130EQC240-2X EPF10K130EQC240-3 EPF10K130EQI240-2 EPF10K130E 240 pin PQFP Pinout Industrial -2 ( -40 to 100C) Commercial ( 0 to 85C) None -1, -2, -3 X: Has PLLs Industrial -2 ( -40 to 100C) None EPF10K200SBC356-1 EPF10K200S 356 pin BGA EPF10K200SBC356-1X Pinout EPF10K200SBC356-2 EPF10K200SBC356-2X EPF10K200SBC356-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K200SBC600-1 EPF10K200S 600 pin BGA Pinout EPF10K200SBC600-1X EPF10K200SBC600-2 EPF10K200SBC600-2X EPF10K200SBC600-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K200SBI356-2 EPF10K200S 356 pin BGA Pinout file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (11 of 15) [2/11/03 5:07:36 PM] Industrial -2 ( -40 to 100C) None Altera Part Number Search Results EPF10K200SFC484-1 EPF10K200S 484 pin FBGA EPF10K200SFC484-1X Pinout EPF10K200SFC484-2 EPF10K200SFC484-2X EPF10K200SFC484-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K200SFC672-1 EPF10K200S 672 pin FBGA EPF10K200SFC672-1X Pinout EPF10K200SFC672-2 EPF10K200SFC672-2X EPF10K200SFC672-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K200SFI672-2 EPF10K200S 672 pin FBGA Pinout EPF10K200SRC240-1 EPF10K200S 240 pin RQFP EPF10K200SRC240-1X Pinout EPF10K200SRC240-2 EPF10K200SRC240-2X EPF10K200SRC240-3 Industrial -2 ( -40 to 100C) None Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs -1, -2, -3 None EPF10K200EBC600-1 EPF10K200EBC600-2 EPF10K200EBC600-3 EPF10K200E 600 pin BGA Pinout Commercial ( 0 to 85C) EPF10K200EBI600-2 EPF10K200E 600 pin BGA Pinout Industrial -2 ( -40 to 100C) EPF10K200EFC672-1 EPF10K200EFC672-2 EPF10K200EFC672-3 EPF10K200E 672 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K200EGC599-1 EPF10K200EGC599-2 EPF10K200EGC599-3 EPF10K200E 599 pin PGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None Your search for EPF10K* found 33 obsolete part numbers. file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (12 of 15) [2/11/03 5:07:36 PM] None Altera Part Number Search Results Obsolete Part Numbers Part Number Format Buying Altera Devices Part Number Last Order Date Last Ship Date Replacement EPF10K100BFC256-1 6/29/01 12/28/01 EPF10K100EFC256-1 PDN 0007 EPF10K100BFC256-2 6/29/01 12/28/01 EPF10K100EFC256-2 PDN 0007 EPF10K100BFC256-3 6/29/01 12/28/01 EPF10K100EFC256-3 PDN 0007 EPF10K100BQC208-1 6/29/01 12/28/01 EPF10K100EQC208-1 PDN 0007 EPF10K100BQC208-2 6/29/01 12/28/01 EPF10K100EQC208-2 PDN 0007 EPF10K100BQC208-3 6/29/01 12/28/01 EPF10K100EQC208-3 PDN 0007 EPF10K100BQC240-1 6/29/01 12/28/01 EPF10K100EQC240-1 PDN 0007 EPF10K100BQC240-2 6/29/01 12/28/01 EPF10K100EQC240-2 PDN 0007 EPF10K100BQC240-3 6/29/01 12/28/01 EPF10K100EQC240-3 PDN 0007 EPF10K100GC503-3 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K100GC503-3DX 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K100GC503-4 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K100GC503-5 Order Order EPF10K100GC503-4 EPF10K100GC503- EPF10K100GC5034 4 ADV 9615 EPF10K10QC208-5 EPF10K10QC208-4 Order Order EPF10K10QC208-4 EPF10K10QC208-4 ADV 9615 EPF10K130VBC600-2 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K130VBC600-3 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K130VBC600-4 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K130VGC599-2 2/28/03 8/31/03 Contact Altera PDN 0107 file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (13 of 15) [2/11/03 5:07:36 PM] Notes Altera Part Number Search Results Contact Us Please Give Us Feedback Sign Up for E-mail Updates EPF10K130VGC599-3 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K130VGC599-4 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K200EGC599-1 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K200EGC599-2 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K200EGC599-3 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K250AGC599-1 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K250AGC599-2 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K250AGC599-3 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K30RC208-5 Order Order EPF10K30RC208-4 EPF10K30RC208-4 EPF10K30RC208-4 ADV 9615 EPF10K50GC403-3 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K50GC403-4 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K50GC403-5 3/31/97 6/30/97 EPF10K50GC403-4 ADV 9623 EPF10K50RC240-5 3/31/97 6/30/97 EPF10K50RC240-4 ADV 9623 EPF10K70GC503-3 2/28/02 8/31/02 Contact Altera PDN 0107 EPF10K70GC503-4 2/28/02 8/31/02 Contact Altera PDN 0107 search EPF10K* Advanced file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (14 of 15) [2/11/03 5:07:36 PM] Help Altera Part Number Search Results Home | Products | Support | System Solutions | Education & Events | Buy On-Line | Corporate Devices | Design Software | Intellectual Property | Design Services | Dev. Kits/Cables | Literature Copyright (c) 1995 - 2002 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA. file:///C|/USER-SHARED/SUD/ALTES00292-1.htm (15 of 15) [2/11/03 5:07:36 PM]