3MTM Pak 100 L/E Pinless Header .100" x .100" Straight, 4-Wall 3000 Series * Optional ejector latches * Shrouded to minimize physical and chemical pin damage * Special holes secure pinless header to back panel * Mounting holes to further secure header to board * Stand-off height allows for one layer wire wrap * See the Regulatory Information Appendix (RIA) in the "RoHS compliance" section of www.3Mconnectors.com for compliance information Date Modified: May 22, 2012 TS-0161-B Sheet 1 of 5 Physical Insulator: Material: Glass Filled Polyester (PBT) Flammability: UL 94V-0 Color: Gray Marking: 3M Logo, Part Identification Number and Orientation Triangle *RoHS = Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment "RoHS compliant" means that the product or part does not contain any of the following substances in excess of the following proposed maximum concentration values in any homogeneous material (unless exempt under RoHS): (a) 0.1% (by weight) for each of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. UL File No.: E68080 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM Pak 100 L/E Pinless Header 3MTM Pak 100 L/E Pinless Header .100" x .100" Straight, 4-Wall 3000 Series .100 x .100 Straight, 4-Wall Table 1 Pin QuanPin Quantity tity Dimensions Table 1 Part Part Number Number A Dimensions A B B D D 2020 6420 6420 1.76 [44.8] 1.605 [40.77] 1.605 [40.77] 1.76 [44.8] 1.21 [30.7] 1.21 [30.7] 2626 6426 6426 2.06 [52.4] 1.51 [38.3] 2.06 [52.4] 1.905 [48.39] 1.905 [48.39] 1.51 [38.3] 3434 6434 6434 2.46 [62.6] 1.91 [48.5] 2.46 [62.6] 2.305 [58.55] 2.305 [58.55] 1.91 [48.5] 4040 6440 6440 2.76 [70.2] 2.21 [56.1] 2.76 [70.2] 2.605 [66.17] 2.605 [66.17] 2.21 [56.1] 50 6450 3.26 [82.9] 2.71 [68.8] 50 6450 3.26 [82.9] 3.105 [78.87] 3.105 [78.87] .08 [2.0] .08 [2.0] .424 .010 [10.77] -9000 Header with No Ejector/Latch .37 Ref [9.4] 2.71 [68.8] .573 .010 [14.55] .46 Ref [11.7] -9200 Header with Short Ejector/Latch for 3M Sockets without Strain Relief 8X .031 .002 [.79 ] (See Note 1 & 2 ) 1.11 [28.2] Ref 1.01 [25.7] Ref 1.11 [28.2] Ref .42 Ref [10.7] -9300 Header with Long Ejector/Latch for 3M Sockets with Strain Relief .100 Typ [2.54] See Note 1 -9400 Header with Ejector Only Note: This Ejector is a Nickel plated Zinc Alloy casting. .16 [4.06] .32 [8.1] Position 1 2X .100 [2.54] (See Note 3) D B A Position 1 Orientation Triangle .25 [6.4] See Note 4 .30 [7.6] .21 [5.3] .25 [6.4] A .22 [5.6] .38 [9.65] 64XX .16 [4.1] 2X .10 [2.5] A .17 [4.3] .72 [18.3] .58 [14.7] .100 [2.54] Section A-A TS-0161-B TS-0161-12 Sheet Sheet 2 of 23 of 5 3 3M Interconnect Solutions Electronic Solutions Division http://www.3M.com/interconnects/ Interconnect Solutions http://www.3Mconnectors.com 3M is aa trademark trademarkofof Company. 3M is 3M3M Company. For or ordering orderinginformation information Fortechnical, technical, sales sales or callcall 800-225-5373 800-225-5373 3MTM Pak 100 L/E Pinless Header .100" x .100" Straight, 4-Wall 3000 Series Table 1 3M Part Number Suffix Dimension H -9000 0.86 [21.8] -9200 1.60 [40.6] -9300 1.78 [45.2] -9400 1.70 [43.2] .050 [1.27] Backplane Pin Field Recommendations .353 Typ [8.95] .106 or .116 Typ [2.69] [2.95] (See Note 3) H .025 .001 Square [0.64] .580 .010 [14.73] (For Flush Mounting) .100 Typ [2.54] .300 [7.62] .100 Typ [2.54] Notes: 1.Accepts .025 .001 sq pins. 2.Four smaller holes at each end used for retention. 3.Accepts Rear and Front entry mounting hardware: Rear entry: #4-24 thread cutting screw 3M Part # 3341-5 ( .116 [2.95] mounting hole) Front entry (Prior to installation of Latch): #2-56 bolt and nut 3M Part # 3341-6. See illustrations on page 4. ( .106 [2.69] mounting hole) 4.These polarization notches will accomodate 3M Polarization Keys 3518. Inch (mm) Tolerance Unless Noted .0 Inch .1 .00 .000 .01 .005 [ ] Dimensions for Reference only Ordering Information 64XX-9X00 Pin Quantity: (See Table 1) Latch/Ejector System 0= No Latch/Ejectors 2= Short, Roll Pin Latch/Ejectors (3M Part #3505-2 ) 3= Long, Roll Pin Latch/Ejectors (3M Part #3505-3 ) 4= Roll Pin Ejectors (3M Part #3505-4) 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com TS-0161-B Sheet 3 of 5 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 TM TM Pak 100 L/E Pinless Header 3M 3M Three-Wall Header .100" x .100" Straight, 4-Wall 3000 Series 3000 Series .100" x .100" Latch/Ejector, Straight and Right Angle Polarizing Post .321 [8.15] 3 2 0 1 -3 3 2 0 1 -4 PBT LCP G ra y B la c k .100 Dia [2.54] Note: Insert Post into one mounting hardware hole on bottom of header. Set post to protrude .115" [2.92] Polarizing Keys Dim A N3518 LCP Blac k .02 3518 PBT Gray .02 Breakaway Tab .09 [2.3] .34 Ref [8.6] A .15 [3.8] Note: #2216 B/A Scotchweld can be used to adhere keys. Mounting Hardware 3341-5 (Installed from bottom of board) 3341-6 (Must be inserted prior to latch on vertical headers) .50 [12.7] .31 [7.9] Panhead Thread Cutting Screw: #4-24 X 5/16" Type: USA Std BT, Federal BG Hex Head Bolt, Nut and Washer Bolt - #2-56 X 1/2" 3341-5 & 6 Material - Stainless Steel Not for use with Condo headers. TS-0161-B TS-0771-E Sheet 4 of 5 Sheet 5 of 5 3 3 Electronic Solutions Division Electronic Solutions Division Interconnect Solutions Interconnect Solutions http://www.3Mconnectors.com http://www.3Mconnector.com 3M is a trademark of 3M Company. is aortrademark of 3M Company. For technical, 3M sales ordering information call For technical, sales or ordering information call 800-225-5373 800-225-5373 Important Notice All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 3M Electronics Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3Mconnectors.com Please recycle. Printed in USA. (c) 3M 2012. All rights reserved. RIA-2217B-E 3M is a trademark of 3M Company.