E2EZ-X2D1-N 2M - Omron Automation and Safety

CSM_E2EZ_DS_E_6_1

Chip-immune Inductive Proximity Sensor

E2EZ

Chip-immune Inductive

Proximity Sensor

• Correct operation even with aluminum or iron chips sticking

to the Sensor.

Only the sensing object is detected.

• Pre-wired Smartclick Connector Models also available.

Be sure to read Safety Precautions on

page 7.

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

Ordering Information

Sensors [Refer to Dimensions on page 8.]

Pre-wired Models

Pre-wired Smartclick Connector Models (M12)

Appearance Sensing distance Output configuration

Model

Operation mode

NO NC

M12 DC 2-Wire Models E2EZ-X2D1-N 2M E2EZ-X2D2-N 2M

M18

DC 3-wire, NPN E2EZ-X4C1 2M —

DC 2-wire E2EZ-X4D1-N 2M E2EZ-X4D2-N 2M

AC 2-wire E2EZ-X4Y1 2M —

M30

DC 3-wire, NPN E2EZ-X8C1 2M —

DC 2-wire E2EZ-X8D1-N 2M E2EZ-X8D2-N 2M

AC 2-wire E2EZ-X8Y1 2M

Shielded

2 mm

4 mm

8 mm

Appearance Sensing distance Output configuration

Model

Operation mode

NO NC

M12

DC 2-wire, (3)-(4) pin arrangement E2EZ-X2D1-M1TJ 0.3M —

DC 2-wire, (1)-(4) pin arrangement E2EZ-X2D1-M1TGJ 0.3M —

M18

DC 2-wire, (3)-(4) pin arrangement E2EZ-X4D1-M1TJ 0.3M —

DC 2-wire, (1)-(4) pin arrangement E2EZ-X4D1-M1TGJ 0.3M —

M30

DC 2-wire, (3)-(4) pin arrangement E2EZ-X8D1-M1TJ 0.3M —

DC 2-wire, (1)-(4) pin arrangement E2EZ-X8D1-M1TGJ 0.3M —

Shielded

2 mm

4 mm

8 mm

E2EZ

Pre-wired Connector Models (M12)

Accessories (Order Separately)

Sensor I/O Connectors (M12, Sockets on One Cable End)

(Models for Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)

[Refer to Dimensions on XS2, XS5.]

Mounting Brackets

Protective Covers

Sputter Protective Covers

Refer to Y92

for details.

Appearance Sensing distance Output configuration

Model

Operation mode

NO NC

M12

DC 2-wire, (3)-(4) pin arrangement E2EZ-X2D1-M1J 0.3M —

DC 2-wire, (1)-(4) pin arrangement E2EZ-X2D1-M1GJ 0.3M —

M18

DC 2-wire, (3)-(4) pin arrangement E2EZ-X4D1-M1J 0.3M —

DC 2-wire, (1)-(4) pin arrangement E2EZ-X4D1-M1GJ 0.3M —

M30

DC 2-wire, (3)-(4) pin arrangement E2EZ-X8D1-M1J 0.3M —

DC 2-wire, (1)-(4) pin arrangement E2EZ-X8D1-M1GJ 0.3M —

Shielded

2 mm

4 mm

8 mm

Appearance Cable length Sensor I/O Connector model number Applicable Proximity Sensor model number

2 m XS2F-D421-DD0

E2EZ-X@D1-M1J

5 m XS2F-D421-GD0

2 m XS2F-D422-DD0

5 m XS2F-D422-GD0

2 m XS2F-D421-DA0-F

E2EZ-X@D1-M1GJ

5 m XS2F-D421-GA0-F

2 m XS2F-D422-DA0-F

5 m XS2F-D422-GA0-F

2 m XS5F-D421-D80-F E2EZ-X@D1-M1TJ

E2EZ-X@D1-M1TGJ

5 m XS5F-D421-G80-F

Straight

L-shape

Straight

L-shape

Smartclick

Connector

Straight

E2EZ

Ratings and Specifications

*1. Use the Sensor within the range in which the green indicator is ON.

*2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and

a set distance of half the sensing distance.

Model E2EZ-X2D@-N

E2EZ-X2D@-M1J

E2EZ-X2D@-M1GJ

E2EZ-X4D@-N

E2EZ-X4D@-M1J

E2EZ-X4D@-M1GJ

E2EZ-X8D@-N

E2EZ-X8D@-M1J

E2EZ-X8D@-M1GJ

E2EZ-X4C1

E2EZ-X4Y1

E2EZ-X8C1

E2EZ-X8Y1

Item

Sensing distance 2 mm ±10% 4 mm ±10% 8 mm ±10% 4 mm ±10% 8 mm ±10%

Set distance *10 to 1.6 mm 0 to 3.2 mm 0 to 6.4 mm 0 to 3.2 mm 0 to 6.4 mm

Differential travel 20% max. of sensing distance

Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.)

Standard sensing

object Iron, 12 × 12 × 1 mm Iron, 30 × 30 × 1 mm Iron, 54 × 54 × 1 mm Iron, 30 × 30 × 1 mm Iron, 54 × 54 × 1 mm

Response

frequency *2200 Hz 100 Hz 30 Hz C Models: 12 Hz

Y Models: 5 Hz

C Models: 8 Hz

Y Models: 5 Hz

Power supply volt-

age

(operating voltage

range)

12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.

C Models: 12 to 24 VDC (10 to 30 VDC), ripple (p-p):

10% max.

Y Models: 100 to 220 VAC (90 to 250 VAC), 50/60 Hz

Current

consumption --- C Models: 15 mA max.

Leakage current 0.8 mA max. Y Models: 2 mA max. at 100 VAC, 3 mA max. at 200 VAC

Con-

trol

output

Load cur-

rent 3 to 100 mA max.

C Models: NPN open-collector output

100 mA max. at 12 VDC (30 VDC max.)

200 mA max. at 24 VDC (30 VDC max.)

Y Models: 10 to 200 mA

Residual

voltage 3 V max. (Load current: 100 mA, Cable length: 2 m)

C Models: 2 V max. (Load current: 200 mA, Cable length:

2 m)

Y Models: Refer to residual voltage characteristic data

Refer to page 4.

Indicators D1 Models: Operation indicator (red), Setting indicator (green)

D2 Models: Operation indicator (red)

C Models: Detection indicator (red)

Y Models: Operation indicator (red)

Operation mode

(with sensing ob-

ject approaching)

D1 Models: NO

D2 Models: NC

For details, refer to the Timing chart on page 5.

For details, refer to the Timing chart on page 6.

Protection

circuits Load short-circuit protection, Surge suppressor

C Models: Load short-circuit protection, Reverse polarity

protection, Surge suppressor

Y Models: Surge suppressor

Ambient

temperature range Operating/Storage: 0 to 50°C (with no icing or condensation)

Ambient

humidity range Operating/Storage: 35% to 95% (with no condensation)

Temperature

influence ±20% max. of sensing distance at 23°C in the temperature range of 0 to 50°C

Voltage influence ±2.5% max. of sensing distance at rated voltage in the rated voltage ±10% range

Insulation

resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case

Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case

C Models: 1,000 VAC, 50/60 Hz for 1 min between cur-

rent-carrying parts and case

Y Models: 2,000 VAC, 50/60 Hz for 1 min between cur-

rent-carrying parts and case

Vibration

resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions

Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions

Degree of

protection IEC 60529 IP67, in-house standards: oil-resistant

Connection

method Pre-wired Models (Standard cable length: 2 m) and Pre-wired Connector Models

Weight

(packed state)

E2EZ-X2D@-N: Approx.

70 g

E2EZ-X2D@-M1J: Approx.

40 g

E2EZ-X2D@-M1GJ:

Approx. 40 g

E2EZ-X4D@-N: Approx.

160 g

E2EZ-X4D@-M1J:

Approx. 90 g

E2EZ-X4D@-M1GJ:

Approx. 90 g

E2EZ-X8D@-N: Approx.

220 g

E2EZ-X8D@-M1J:

Approx. 160 g

E2EZ-X8D@-M1GJ:

Approx. 160 g

Approx. 170 g Approx. 270 g

Materi-

als

Case Nickel-plated brass

Sensing

surface PBT Heat-resistant ABS

Clamp-

ing nuts Zinc-plated iron

Toothed

washer Zinc-plated iron

Accessories Instruction manual

E2EZ

Engineering Data (Reference Value)

Sensing Area

E2EZ-X2@E2EZ-X4@E2EZ-X8@

Influence of Sensing Object Size and Material

E2EZ-X2@E2EZ-X4@E2EZ-X8@

Residual Output Voltage

E2EZ-X@D@-N E2EZ-X4Y1/-X8Y1 at 100 VAC E2EZ-X4Y1/-X8Y1 at 200 VAC

0.5

1.0

1.5

2.0

2.5

86420−2−4−6−8

0.0

Distance Y

(mm)

Sensing Head

Distance X (mm)

−2−4−6−8−10

1086420

Distance Y

(mm)

Sensing Head

Distance X (mm)

−8−12−16−20

201612840−4

Distance Y

(mm)

Sensing Head

Distance X (mm)

40302010

Side length of sensing object: d (mm)

Brass

Iron

Aluminum

Stainless steel

(SUS304)

Distance X (mm)

d ×

d t = 1 mm

605040302010

d ×

d t = 1 mm

Side length of sensing object: d (mm)

Brass Iron Aluminum

Stainless

steel

(SUS304)

Copper

Distance X (mm)

010

6050403020

d ×

d t = 1 mm

Side length of sensing object: d (mm)

Iron

Brass

Aluminum

Copper

Stainless

steel

(SUS304)

Distance X (mm)

10531

1,0005003001005030

Load current (mA)

Residual output voltage (V)

50 A

100 VAC

OFF

200150100501050

100

Residual output

voltage

Residual load

voltage

Load voltage (V)

Load current (mA)

200 VAC

100

150

200

105 20015010050

OFF

Residual output

voltage

Residual

load

voltage

Load voltage (V)

Load current (mA)

E2EZ

I/O Circuit Diagrams

DC 2-Wire Models

Leakage Current

E2EZ-X4Y1/-X8Y1 E2EZ-X@D@-N

Opera-

tion

mode

Model Timing chart Output circuit

E2EZ-X2D1-N

E2EZ-X4D1-N

E2EZ-X8D1-N

E2EZ-X2D1-M1J

E2EZ-X2D1-M1GJ

E2EZ-X4D1-M1J

E2EZ-X4D1-M1GJ

E2EZ-X8D1-M1J

E2EZ-X8D1-M1GJ

E2EZ-X2D2-N

E2EZ-X4D2-N

E2EZ-X8D2-N

25020015010090

AC power

Power supply voltage (V)

Leakage current (mA)

Protective

resistance

02010

0.5

1.0

1.5

4030

Power supply voltage (V)

Leakage current (mA)

80(TYP)

100

(%)

Sensing

object

Rated sensing

distance

Stable sensing area

Non-sensing

area

Unstable

sensing

area

Set position

OFF

Setting indicator

(green)

Operation

indicator (red)

Control output

0 V

Load

Brown

Blue

Prox-

imity

Sensor

main

circuit

Note: The load can be connected to either the

+V or 0 V side.

(M1J)

0 V

Load

Prox-

imity

Sensor

main

circuit

Note: The load can be connected to either the +V or 0 V side.

Load

Prox-

imity

Sensor

main

circuit

Note: The load can be connected to either the +V or 0 V side.

Connector Pin

Arrangement

Note: Pins 1 and 2

are not used.

Connector Pin

Arrangement

Note: Pins 2 and 3

are not used.

(M1GJ)

0100

(%)

Sensing

object

Rated sensing

distance

Sensing areaNon-sensing area

OFF

Operation

indicator (Red)

Control output

0 V

Load

Brown

Blue

Prox-

imity

Sensor

main

circuit

Note: The load can be connected to either the

+V or 0 V side.

E2EZ

DC 3-wire Models

AC 2-Wire Models

Connections for Sensor I/O Connectors

Operation

mode Model Timing chart Output circuit

NO E2EZ-X4C1

E2EZ-X8C1

Operation

mode Model Timing chart Output circuit

NO E2EZ-X4Y1

E2EZ-X8Y1

Present

Not present

Operate

Reset

OFF

Sensing object

Load

Detection indicator (red)

2.2 Ω

0 V

Proximity

Sensor

main

circuit

Load

Brown

Black

Output

Blue

* 100 mA max. at 12 V, 200 mA max. at 24 V

(load current).

Present

Not present

Operate

Reset

OFF

Sensing object

Load

Operation indicator (red)

Load

Brown

Blue

Prox-

imity

Sensor

main

circuit

Proximity Sensor Sensor I/O Connectors

Connections

Model Operation

mode Model Model

DC 2-Wire Models

(IEC pin wiring)

E2EZ-X@D1-M1GJ

DC 2-Wire Models

(previous pin wir-

ing)

E2EZ-X@D1-M1J

DC 2-Wire Models

(IEC pin wiring) E2EZ-X@D1-M1TGJ

DC 2-Wire Models

(previous pin wir-

ing)

E2EZ-X@D1-M1TJ

XS2F-D42@-@A0-F

1: Straight

2: L-shape

D: 2-m cable

G: 5-m cable

XS2F

E2EZ

main

circuit

Brown (+)

Blue (−)

XS2F-D42@-@D0

1: Straight

2: L-shape

D: 2-m cable

G: 5-m cable

XS2F

E2EZ

main

circuit

Blue (−)

Brown (+)

XS5F-D421-@80-F

D: 2-m cable

G: 5-m cable

XS5F

E2EZ

main

circuit

Brown (+)

White

Blue

Black (−)

XS5F

E2EZ

main

circuit

Blue (−)

Black (+)

Brown

White

Refer to Introduction to Sensor I/O Connectors/Sensor Controllers for details.

E2EZ

Safety Precautions

Refer to Warranty and Limitations of Liability.

This product is not designed or rated for ensuring

safety of persons either directly or indirectly.

Do not use it for such purposes.

Do not use this product under ambient conditions that exceed the

ratings.

● Design

Influence of Surrounding Metal

When mounting the Sensor within a metal panel, ensure that the

clearances given in the following table are maintained. Failure to

maintain these distances may cause deterioration in the performance

of the Sensor.

Influence of Surrounding Metal (Unit: mm)

Mutual Interference

When installing Sensors face-to-face or side-by-side, ensure that the

minimum distances given in the following table are maintained.

Aluminum and Iron Cuttings

Normally aluminum or iron cuttings will not be detected even if they

adhere to or accumulate on the sensing surface.

Detection signals may be output for the following:

If this occurs, remove the cuttings from the sensing surface.

1. Relationship between the Size of the Cutting (d) and the Size of

the Sensing Surface (D)

Cuttings of the size d ≥ D on the sensing surface *

● Mounting

Do not tighten the nut with excessive force.

A washer must be used with the nut.

Note: 1. The allowable tightening strength depends on the distance from the

edge of the head, as shown in the following table. (A is the distance

from the edge of the head. B includes the nut on the head side. If the

edge of the nut is in part A, the tightening torque for part A applies

instead.)

2. The following torque assume washers are being used.

WARNING

Precautions for Correct Use

Item

l d D m n

Model

Embedded

material

E2EZ-X2@Iron 0120 818

Aluminum 2252 36

E2EZ-X4@Iron 018016 27

Aluminum 5405 54

E2EZ-X8@Iron 030032 45

Aluminum 10 70 10 90

d dia.

Mutual Interference (Unit: mm)

Model Item A B

E2EZ-X2@30 20

E2EZ-X4@40 50

E2EZ-X8@60 100

Tightening

Torque Part A Part B

Model

Dimension

(mm) Torque Torque

E2EZ-X2D@-@30 N·m

E2EZ-X4D@-@70 N·m

E2EZ-X8D@-@180 N·m

E2EZ-X4C1

E2EZ-X4Y1 20 15 N·m 29 N·m

E2EZ-X8C1

E2EZ-X8Y1 22 29 N·m 39 N·m

Sensing

surface

Cutting

Pressed against

sensing surface.

Cuttings of the size d*(Unit: mm)

*E2EZ-X2@: d ≥ D on the sensing surface.

2. Cuttings Pressed against the Sensing

Surface

Model Size D

E2EZ-X2@10 *

E2EZ-X4@16

E2EZ-X8@28

Part B Part A

E2EZ

Dimensions

Mounting Hole Dimensions

(Unit: mm)

Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.

38 9

17 4

21 dia.

M12

15 dia.

M12 × 1

Indicator*2

Two clamping nuts

Toothed washer

*1. 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2,

Insulator diameter: 1.3 mm), Standard length: 2 m

*2. D1 Models: Operation indicator (red), Setting indicator (green), D2 Models: Operation

indicator (red)

Pre-wired Connector Models (-M1J/M1GJ)

4-dia. vinyl-insulated round cable with

2 conductors (Conductor cross

section: 0.3 mm2, Insulator diameter:

1.3 mm), Standard length: 300 mm

E2EZ-X2D@-N

15 dia.

M12 × 1

Pre-wired Connector Models (-M1J/M1GJ)

6-dia. vinyl-insulated round cable with

2 conductors (Conductor cross section:

0.5 mm2, Insulator diameter: 1.9 mm),

Standard length: 300 mm

E2EZ-X4D@-N

43 12

29 dia.

M18 × 1

Indicator*2

Two clamping nuts

Toothed washer

*1. 6-dia. vinyl-insulated round cable with 2 conduc

tors (Conductor cross section: 0.5 mm2, Insula-

tor diameter: 1.9 mm), Standard length: 2 m

The cable can be extended up to 200 m (sepa-

rate metal conduit).

*2. D1 Models: Operation indicator (red), Setting in-

dicator (green)

D2 Models: Operation indicator (red)

48 12

42 dia.

M30 × 1.5

Indicator*2

Two clamping nuts

Toothed washer

*1. 6-dia. vinyl-insulated round cable with 2 con-

ductors (Conductor cross section: 0.5 mm2, In-

sulator diameter: 1.9 mm), Standard length: 2 m

The cable can be extended up to 200 m (sepa-

rate metal conduit).

*2. D1 Models: Operation indicator (red), Setting

indicator (green)

D2 Models: Operation indicator (red)

15 dia.

M12 × 1

Pre-wired Connector Models (-M1J/M1GJ)

6-dia. vinyl-insulated round cable with

2 conductors (Conductor cross section:

0.5 mm2, Insulator diameter: 1.9 mm),

Standard length: 300 mm

E2EZ-X8D@-N

E2EZ-X4C1

E2EZ-X4Y1

29 dia.

M18

Two toothed washers Two clamping nuts

Indicator

*2. C Models: Detection indicator (red),

Y Models: Operation indicator (red)

*1. C Models: 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross

section: 0.5 mm

, Insulator diameter: 1.9 mm), Standard length: 2 m

Y Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross

section: 0.5 mm

, Insulator diameter: 1.9 mm), Standard length: 2 m

E2EZ-X8C1

E2EZ-X8Y1 80

42 dia.

M30 × 1.5 55

Two toothed washers Two clamping nuts

Indicator*2

*2. C Models: Detection indicator (red),

Y Models: Operation indicator (red)

*1. C Models: 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross

section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m

Y Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross

section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m

Model F (mm)

E2EZ-X2@12.5 dia.

E2EZ-X4@18.5 dia.

E2EZ-X8@30.5 dia.

+0.5

−0

+0.5

−0

+0.5

−0

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you

have any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron

disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER

ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the

Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount

equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,

repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products

were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate

modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall

not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or

electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above

warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself

is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,

system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product

with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate

it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our

practice to change part numbers when published ratings or features are changed, or when significant construction changes are

made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers

may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at

any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

2014.1

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Omron:

E2EZ-X2D1-N 2M E2EZ-X2D2-N 2M E2EZ-X4B1 E2EZ-X4B1-M1J 0.3M E2EZ-X4C1-5M E2EZ-X4D1-M1GJ 0.3M

E2EZ-X4D1-M1GJ 1M(NEW) E2EZ-X4D1-M1GJ 2M E2EZ-X4D1-N 2M E2EZ-X4D1-N 5M E2EZ-X4D1-R E2EZ-

X4D2-N E2EZ-X4D2-N 5M E2EZ-X4Y1 E2EZ-X4Y1-5M E2EZ-X8C1-5M E2EZ-X8D1-M1GJ 0.3M E2EZ-X8D1-N 5M

E2EZ-X8D2-N 5M E2EZ-X8Y1 E2EZ-X8Y1-5M