LM79M05,LM79M12,LM79M15 LM79MXX Series 3-Terminal Negative Regulators Literature Number: SNOS553C LM79MXX Series 3-Terminal Negative Regulators General Description The LM79MXX series of 3-terminal regulators is available with fixed output voltages of -5V, -12V, and -15V. These devices need only one external component -- a compensation capacitor at the output. The LM79MXX series is packaged in the TO-220 power package, and is capable of supplying 0.5A of output current. These regulators employ internal current limiting, safe area protection, and thermal shutdown for protection against virtually all overload conditions. Low ground pin current of the LM79MXX series allows output voltage to be easily boosted above the preset value with a resistor divider. The low quiescent current of these devices with a specified maximum change with line and load ensures good regulation in the voltage boosted mode. For output voltage other than -5V, -12V, and -15V the LM137 series provides an output voltage range from -1.2V to -57V. Features n n n n Thermal, short circuit and safe area protection High ripple rejection 0.5A output current 4% tolerance on preset output voltage Connection Diagram TO-220 Plastic Package (T) 01048307 Front View Order Number LM79M05CT, LM79M12CT or LM79M15CT See NS Package Number T03B (c) 2004 National Semiconductor Corporation DS010483 www.national.com LM79MXX Series 3-Terminal Negative Regulators September 2001 LM79MXX Series Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Power Dissipation (Note 2) Internally Limited Operating Junction Temperature Range Input Voltage 0C to +125C VO = -5V -25V Storage Temperature Range VO = -12V, -15V -35V Lead Temperature (Soldering, 10 sec.) Input/Output Differential VO = -5V VO = -12V, -15V 25V 30V -65C to +150C 230C ESD Susceptibility TBD Electrical Characteristics LM79M05C Conditions unless otherwise noted: IOUT = 350mA, CIN = 2.2F, COUT = 1F, 0C TJ +125C Part Number LM79M05C Output Voltage -5V Input Voltage (Unless Otherwise Specified) Symbol VO Parameter Output Voltage Units -10V Conditions Min Typ Max TJ = 25C -4.8 -5.0 -5.2 V 5mA IOUT 350mA -4.75 -5.25 V 50 mV 30 mV 100 mV (-25 VIN -7) VO Line Regulation TJ = 25C (Note 3) 8 (-25 VIN -7) 2 (-18 VIN - 8) VO Load Regulation TJ = 25C, (Note 3) IQ Quiescent Current TJ = 25C IQ Quiescent Current With Input Voltage 30 5mA IOUT 0.5A 1 2 mA 0.4 mA 0.4 mA (-25 VIN -8) Change With Load, 5mA IOUT 350mA Vn Output Noise Voltage TA = 25C, Ripple Rejection f = 120Hz 150 V 66 dB 10Hz f 100Hz 54 (-18 VIN -8) IOMAX Dropout Voltage TJ = 25C, IOUT = 0.5A 1.1 V Peak Output Current TJ = 25C 800 mA Average Temperature IOUT = 5mA, Coefficient of 0C TJ 100C -0.4 mV/C Output Voltage www.national.com 2 Conditions unless otherwise noted: IOUT = 350mA, CIN = 2.2F, COUT = 1 F, 0C TJ +125C Part Number Output Voltage Input Voltage (Unless Otherwise Specified) Symbol VO Parameter Output Voltage LM79M12C LM79M15C -12V -15V -19V Conditions -23V Min Typ Max Min Typ Max TJ = 25C -11.5 -12.0 -12.5 -14.4 -15.0 -15.6 V 5 mA IOUT 350mA -11.4 -12.6 -14.25 -15.75 V (-27 VIN -14.5) VO Line Regulation TJ = 25C (Note 3) 5 3 Load Regulation (-30 VIN -10.5) 80 (-30 VIN -14.5) VO Units 5 80 50 3 50 mV 240 mV 3 mA 0.4 mA (-25 VIN - 15) (-28 VIN -18) 30 240 30 3 1.5 TJ = 25C, (Note 3) mV (-30 VIN -17.5) 5mA IOUT 0.5A IQ Quiescent Current TJ = 25C IQ Quiescent Current With Input Voltage 1.5 0.4 (-30 VIN -14.5) Change (-30 VIN -27) With Load, 5mA IOUT 350mA Vn Output Noise Voltage Ripple Rejection IOMAX 0.4 TA = 25C, 0.4 400 mA 400 V 70 dB 10Hz f 100Hz f = 120Hz 54 70 54 (-25 VIN -15) (-30 VIN -17.5) Dropout Voltage TJ = 25C, IOUT = 0.5A 1.1 1.1 V Peak Output Current TJ = 25C 800 800 mA -0.8 -1.0 mV/C Average Temperature IOUT = 5mA, Coefficient of 0C TJ 100C Output Voltage Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: Refer to Typical Performance Characteristics and Design Considerations for details. Note 3: Regulation is measued at a constant junction temperature by pulse testing with a low duty cycle. Changes in output voltage due to heating effects must be taken into account. Typical Performance Characteristics Output Voltage vs. Temperature Ripple Rejection 01048311 01048312 3 www.national.com LM79MXX Series Electrical Characteristics LM79M12C, LM79M15C LM79MXX Series Typical Performance Characteristics (Continued) Minimum Input-Output Differential Output Impedance 01048314 01048313 Quiescent Current vs. Input Voltage Quiescent Current vs. Load Current 01048316 01048315 www.national.com 4 LM79MXX Series Typical Performance Characteristics (Continued) Maximum Average Power Dissipation (TO-220) Short-Circuit Current 01048318 01048317 Schematic Diagrams -5V 01048308 5 www.national.com LM79MXX Series Schematic Diagrams (Continued) -12V and -15V 01048309 www.national.com 6 The LM79MXX fixed voltage regulator series have thermaloverload protection from excessive power, internal shortcircuit protection which limits the circuit's maximum current, and output transistor safe-area compensation for reducing the output current as the voltage across the pass transistor is increased. Fixed Regulator Although the internal power dissipation is limited, the junction temperature must be kept below the maximum specified temperature in order to meet data sheet specifications. To calculate the maximum junction temperature or heat sink required, the following thermal resistance values should be used: Package TO-220 JC JA (C/W) (C/W) 3 40 01048302 *Required if regulator is separated from filter capacitor by more than 3". For value given, capacitor must be solid tantalum. 25F aluminum electrolytic may be substituted. Required for stability. For value given, capacitor must be solid tantalum. 25F aluminum electrolytic may be substituted. Values given may be increased without limit. For output capacitance in excess of 100F, a high current diode from input to output (1N4001, etc.) will protect the regulator from momentary input shorts. (1) Variable Output CA = CS+SA Solving for TJ: TJ = TA+ PD (JC+CA) or = TA=+ PDJA(Without a Heat Sink) Where TJ = Junction Temperature TA = Ambient Temperature PD = Power Dissipation JC = Junction-to-Case Thermal Resistance CA = Case-to-Ambient Thermal Resistance 01048303 *Improves transient response and ripple rejection. Do not increase beyond 50F. CS = Case-to-Heat Sink Thermal Resistance SA = Heat Sink-to-Ambient Thermal Resistance JA = Junction-to-Ambient Thermal Resistance Select R2 as follows: Typical Applications Bypass capacitors are necessary for stable operation of the LM79MXX series of regulators over the input voltage and output current ranges. Output bypass capacitors will improve the transient response of the regulator. 7 LM79M05C 300 LM79M12C 750 LM79M15C 1k www.national.com LM79MXX Series The bypass capacitors (2.2F on the input, 1.0F on the output), should be ceramic or solid tantalum which have good high frequency characteristics. If aluminum electrolytics are used, their values should be 10F or larger. The bypass capacitors should be mounted with the shortest leads, and if possible, directly across the regulator terminals. Design Considerations LM79MXX Series Typical Applications (Continued) 15V, 1 Amp Tracking Regulators 01048301 *Resistor tolerance of R4 and R5 determine matching of (+) and (-) outputs. **Necessary only if raw supply filter capacitors are more than 3" from regulators. Performance (Typical) (-15) (+15) 40mV 2 mV 100 Vrms 100 Vrms Load Regulation at 0.5A Output Ripple, CIN = 3000F, IL = 0.5A Temperature Stability Output Noise 10Hz f 10kHz 50mV 50mV 150 Vrms 150 Vrms Dual Trimmed Supply 01048304 www.national.com 8 LM79MXX Series 3-Terminal Negative Regulators Physical Dimensions inches (millimeters) unless otherwise noted TO-220 Plastic Package (T) Order Number LM79M05CT, LM79M12CT or LM79M15CT NS Package Number T03B National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated