VRSM = 150 V, IF(AV) = 30 A
Schottky Diode
FMET-23015 Data Sheet
FMET-23015-DSE Rev.1.0 SANKEN ELCTRIC CO., LTD. 1
Apr. 04, 2017 http://www.sanken-ele.co.jp/en
© SANKEN ELECTRIC CO., LTD. 2016
Description
The FMET-23015 is a 150 V, 30 A Schottky diode
with a trench structure, allowing improvements in VF
and IR characteristics. These characteristic features
contribute to improving power supply efficiency and to
enabling high-frequency systems.
Features
● VRSM ---------------------------------------------------- 150 V
● IF(AV) ------------------------------------------------------- 30 A
● VF (IF = 15 A) ---------------------------------- 0.90 V typ.
● RoHS Compliant
Applications
High speed switching applica tions such as:
● DC-DC Conve rte r
● Adapter
Package
TO220F-3L
Not to scale
(1) (3)
(2)
(1)(2)(3)
(1) Anode
(2) Cathode
(3) Anode
Not Recommended for New Designs
FMET-23015
FMET-23015-DSE Rev.1.0 SANKEN ELCTRIC CO., LTD. 2
Apr. 04, 2017 http://www.sanken-ele.co.jp/en
© SANKEN ELECTRIC CO., LTD. 2016
Absolute Maximum Ratings
Unless otherwise specified, TA = 25 °C.
Parameter Symbol Rating Unit Conditions
Peak Repetitive Reverse Voltage(1) VRSM 150 V
Repetitive Re verse Voltage(1) VRM 150 V
Average Forward Current(2) IF(AV) 30 A See Figure 1 and Figure 2
Surge Forward Current(1) IFSM 150 A
Half cycle sine wave,
positive side, 10 ms, 1 shot
I2t Limiting Value(1) I2t 112.5 A2s
Junct ion Temperature TJ −40 to 150 °C
Storage Temperature TSTG −40 to 150 °C
Electrical Characteristics
Unless otherwise specified, TA = 25 °C.
Parameter Symbol Conditions Min. Typ. Max. Unit
Forward Voltage Drop
(1)
VF IF = 15 A — 0.90 0.98 V
Reverse Lea kage Current(1) IR VR = VRM — — 150 µA
Reverse Lea kage Current
under Hi gh Temperatur e
(1)
H∙IR VR = VRM, T J = 150 °C — — 75 mA
Thermal Resista nce(3) Rth(J-C) — — 4.0 °C/W
(1) Specifies a value per chip; t h e FMET-23015 consists of tw o chips.
(2) Specifies a value of the t wo chips configuring the product; a value per chip is 15 A.
(3) Rth (J-C) is thermal resistance between junction and the case. The case temperature is measured at the back side near t he
screw ho le.
Not Recommended for New Designs
FMET-23015
FMET-23015-DSE Rev.1.0 SANKEN ELCTRIC CO., LTD. 3
Apr. 04, 2017 http://www.sanken-ele.co.jp/en
© SANKEN ELECTRIC CO., LTD. 2016
Rating and Characteristic Curves
Figure 1. TC vs. IF(AV) Typical Character istics
(VR = 0 V)
Figure 2. TC vs. IF(AV) Typical Character istics
(VR = 150 V)
Figure 3. VF vs. IF Typical C har a c te r istics
Figure 4. VR vs. IR Typical Characteristics
0
5
10
15
20
25
30
0 25 50 75 100 125 150
Average
Forward Curr e nt, IF(AV) (A)
Case Temperature, TC (°C)
0
5
10
15
20
25
30
0 25 50 75 100 125 150
Average Forward Cur re nt, IF(AV) (A)
Case Temperature, TC (°C)
0.001
0.01
0.1
1
10
100
0.0 0.2 0.4 0.6 0.8 1.0 1.2
Forward Current, I F (A)
Forward Voltage, VF (V)
1.E-07
1.E-06
1.E-05
1.E-04
1.E-03
1.E-02
0 50 100 150
Reverse Current, IR (A)
Reverse Voltage, VR (V)
TJ = 150 °C
TJ = 25 °C
TJ = 100 °C
DC
t/T = 1/6
TJ = 25 °C
TJ = 100 °C
TJ = 125 °C
TJ = 150 °C
T
J
= 150 °C
tT
T
J
= 150 °C
tT
t/T = 1/3
t/T = 1/2
Sine wave
TJ = 125 °C
DC
t/T = 1/6
Sine wave, t/T = 1/3
t/T = 1/2
Not Recommended for New Designs
FMET-23015
FMET-23015-DSE Rev.1.0 SANKEN ELCTRIC CO., LTD. 4
Apr. 04, 2017 http://www.sanken-ele.co.jp/en
© SANKEN ELECTRIC CO., LTD. 2016
Physical Dimensions
● TO220F
2.8 ±0.2
4.2 ±0.2
4 ±0.2
8.4 ±0.2
16.9 ±0.3
3.9 ±0.2
(13.5)
1.35 ±0.15
1.35 ±0.15
0.85
+0.2
-0.1
0.8 ±0.2
C0.5 ±0.1
2.6 ±0.1
0.45
+0.2
-0.1
2.54 ±0.1 2.54 ±0.1
3.2 ±0.2
10.0 ±0.2
(Roots of pins)(Roots of pins)
2.2 ±0.2
123
0.7 0.7
0.7 0.7
Side ViewPlan View
(Root of pin)
Gate burr
NOTES:
- Dimensions in millimeters
- Maxi mu m gate burr he ig ht is 0.3 mm.
- Bare lead frame: Pb-free (RoHS compliant)
- When soldering the products, it is required to minimize the working time, within the following limits:
Flow: 260 ± 5 °C / 10 ± 1 s, 2 times
Soldering Iron: 380 ± 10 °C / 3.5 ± 0.5 s, 1 time (Soldering should be at a distance of at least 1.5 mm fro m the
body of the product.)
Recommended screw torque for TO220F: 0.490 N∙m to 0.686 N∙m (5 kgf∙cm to 7 kgf∙cm)
Not Recommended for New Designs
FMET-23015
FMET-23015-DSE Rev.1.0 SANKEN ELCTRIC CO., LTD. 5
Apr. 04, 2017 http://www.sanken-ele.co.jp/en
© SANKEN ELECTRIC CO., LTD. 2016
Marking Diagram
1
ET3015
Y M D D
32
S pecif ic Device Code
L ot Numbe r:
Y is the last d igit of the y ear o f manuf acture (0 to 9)
M is the month of the yea r (1 to 9, O, N , or D)
DD is the da y of the month (01 to 31)
Table 1. Specific Device Code
Specific Device Code Part Number
ET3015 FMET-23015
(see Table 1)
Not Recommended for New Designs
FMET-23015
FMET-23015-DSE Rev.1.0 SANKEN ELCTRIC CO., LTD. 6
Apr. 04, 2017 http://www.sanken-ele.co.jp/en
© SANKEN ELECTRIC CO., LTD. 2016
Important Notes
● All data, illustrations, graphs, tables and any other information included in this document as to Sanken’s products listed herein (the
“Sanken Products”) are current as of the date this document is issued. All contents in this document are subject to any change
without notice due to improvement of the Sanken Products, etc. Please make sure to confirm with a Sanken sales representative
that the contents set forth in this document reflect the latest revisions before use.
● The Sanken Products are intended for use as components of general purpose electronic equipment or apparatus (such as home
appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Prior to use of the Sanken Products,
please put your signature, or affix your name and seal, on the specification documents of the Sanken Products and return them to
Sanken. When considering use of the Sanken Products for any applications that require higher reliability (such as transportation
equipment and its control systems, traffic signal control systems or equipment, disaster/crime alarm systems, various safety
devices, et c.), you must contact a Sanken sales representative to discuss the suitability of such use and put your signature, or affix
your name and seal, on the specification documents of the Sanken Products and return them to Sanken, prior to the use of the
Sanken Products. The Sanken Products are not intended for use in any applications that require extremely high reliability such as:
aerospace equipment; nuclear power control systems; and medical equipment or systems, whose failure or malfunction may result
in death or serious injury to people, i.e., medical devices in Class III or a higher class as defined by relevant laws of Japan
(collectively, the “Specific Applications”). Sanken assumes no liability or responsibility whatsoever for any and all damages and
losses that may be suffered by you, users or any third party, resulting from the use of the Sanken Products in the Specific
Applications or in manner not in compliance with the instructions set forth herein.
● In the event of using the Sanken Products by either (i) combining other products or materials therewith or (ii) physically,
chemically or otherwise processing or treating the same, you must duly consider all possible risks that may result from all such
uses in advance an d proceed therewith at your own responsibility.
● Although Sanken is making efforts to enhance the quality and reliability of its products, it is impossible to completely avoid the
occurrence of any failure or defect in semiconductor products at a certain rate. You must take, at your own responsibility,
preventative measures including using a sufficient safety design and confirming safety of any equipment or systems in/for which
the Sanken Products are used, upon due consideration of a failure occurrence rate or derating, etc., in o rder not to cause any human
injury or death, fire accident or social harm which may result from any failure or malfunction of the Sanken Products. Please refer
to the rel evant specification documents and Sanken’s official website in relation to derating.
● No anti-radioactive ray design has been adopted for the Sanken Products.
● No contents in this document can be transcribed or copied without Sanken’s prior written consent.
● The c ircuit constant, operation examples, circui t examples, pat tern layou t examples, d esign examples, recommen ded examples, all
information and evalu ation results based thereo n, etc. , described in this document are presented for the sole purpose of reference of
use of the Sanken Products and Sanken assumes no responsibility whatsoever for any and all damages and losses that may be
suffered by you, users or any third party, or any possible infringement of any and all property rights including intellectual property
rights and any other rights of you, users or an y third party, resulting from the foregoing.
● All technical information described in this document (the “Technical Information”) is presented for the sole purpose of reference
of use of the Sanken Products and no license, express, implied or otherwise, is granted hereby under any intellectual property
rights or any other rights of Sanken.
● Unless otherwise agreed in writing between Sanken and you, Sanken makes no warranty of any kind, whether express or implied,
including, without limitation, any warranty (i) as to the quality or performance of the Sanken Products (such as implied warranty
of merchantability, or implied warranty of fitness for a particular purpose or special environment), (ii) that any Sanken Product is
delivered free of claims of third parties b y way of infrin gement o r the like, (iii) that may arise fro m cour se of performance, course
of dealing or usage of trade, and (iv) as to any information contained in this document (including its accuracy, usefulness, or
reliability).
● In the event of using the Sanken Products, you must use th e sa me after care fully exa mining all applicab le environmental law s and
regulations that regulate the inclusion or use of any particular controlled substances, including, but not limited to, the EU RoHS
Directive, so as to be in strict compliance with such applicable laws and regulations.
● You must not use the Sanken Products or the Technical Information for the purpose of any military applications or use, including
but not limited to the development of weapons of mass destruction. In the event of exporting the Sanken Products or the Technical
Information, or providing them for non-residents, you must comply with all applicable export control laws and regulations in each
country including the U. S. Export Administration Regulations (EAR) and the F oreign Exchange and F oreign Trade Act of Japan,
and follow the procedures required by such applicable l aws and regulations.
● Sanken assumes no responsibility for any troubles, which may occur during the transportation of the Sanken Products including
the falling thereof, out of Sanken’s distribution network.
● Although Sanken has prepared this document with its due care to pursue the accuracy thereof, Sanken does not warrant that it is
error free and Sanken assumes no liab ility whats oever for any and all damages and losses which may be suffered by you resulting
from any possible errors or omissions in connection with the contents included herein.
● Please refer to th e relev ant specification documents in relation to particular precautions when using the Sanken Products, and refer
to our official website in relation to general instructions and directions for using the Sanken Products.
● All rights and title in and to any specific trademark or tradename belong to Sanken or such original right holder(s).
DSGN-CEZ-16002
Not Recommended for New Designs
