RECORDS OF REVISION Date Rev. Description Page Design by 2006/04/19 0 MASS PRODUCTION --- PETER Total27 Page PE240128WRF-001-HQ VER.0 Page2 Contents 1. SPECIFICATIONS 1.1 1.2 1.3 1.4 1.5 1.6 Features Mechanical Specifications Absolute Maximum Ratings DC Electrical Characteristics Optical Characteristics Backlight Characteristics 2. MODULE STRUCTURE 2.1 Counter Drawing 2.2 Interface Pin Description 2.3 Timing Characteristics 2.4 Display Command 3. QUALITY ASSURANCE SYSTEM 3.1 3.2 Quality Assurance Flow Chart Inspection Specification 4. RELIABILITY TEST 4.1 Reliability Test Condition 5. PRECAUTION RELATING PRODUCT HANDLING 5.1 Safety 5.2 Handling 5.3 Storage 5.4 Terms of Warranty Appendix ALCM Drawing Appendix BPackage Note : For detailed information please refer to IC data sheet : Sitronix --- ST7529-G PE240128WRF-001-HQ VER.0 Page3 1. SPECIFICATIONS 1.1 Features Item Standard Value Display Type 240 * 128 Dots LCD Type FSTN , Positive , Transflective Driver Condition LCD Module : 1/160 Duty , 1/10 Bias Viewing Direction 6 O'clock Backlight Type LED B/L Weight Interface 50 g Support 8 Bit Parallel interface with 8080 or 6800 series MPU & IIC serial interface Driver IC 1.2 SITRONIX - ST7529-G Mechanical Specifications Item Standard Value Unit Outline Dimension 99.2 (L) * 64.2 (w) * 18.04 (H)(Max) mm Viewing Area 93.0 (L) * 49.0 (w) mm Active Area 82.775 (L) * 44.135 (w) mm Dot Size 0.32 (L) * 0.32 (w) mm Dot Pitch 0.345 (L) * 0.345 (w) mm Note : For detailed information please refer to LCM drawing 1.3 Absolute Maximum Ratings Item Symbol Condition Min. Max. Unit Power Supply Voltage VDD - -0.5 5.0 V LCD Driver Supply Voltage VLCD -VSS - -0.5 +22 V Input Voltage VIN - -0.5 VDD + 0.5 V Operating Temperature TOP - -20 70 C Storage Temperature TST - -30 80 C Storage Humidity HD Ta < 40 C 20 90 %RH PE240128WRF-001-HQ VER.0 Page4 1.4 DC Electrical Characteristics VDD = 3.3 V 0.3 , VSS = 0 V , Ta = 25C Item Symbol Condition Min. Typ. Max. Unit Logic Supply Voltage VDD - 3.0 3.3 3.6 V High-level Input Voltage VIH - 0.7VDD - VDD V Low-level Input Voltage VIL - VSS - 0.3VDD V High-level Output Voltage VOH - - - - V Low-level Input Voltage VOL - - - - V Supply Current IDD VDD = 3.3 V - 1.2 6.2 mA VOP Vo - Vss (-20C) 14.0 14.1 14.2 V VOP Vo - Vss (25C) *1 12.8 12.95 13.1 V VOP Vo - Vss (70C) 11.7 11.8 11.9 V LCM Driver Voltage NOTE:*1 The VOP test point is Vo - Vss. NOTE:2 :Recommended Power Supply Combinations. 1.5 Optical Characteristics LCD Panel: 1/160 Duty , 1/13 Bias , VLCD = 15.06 V Ta = 25C Item Symbol Conditions Min. Typ. Max. Reference View Angle C>2.0 , = 270 -40 - +40 Note 1 Contrast Ratio CR = -5 , = 270 2 2.8 - Note 3 Response Time(rise) Tr = -5 , = 270 - 135 ms 205 ms Response Time(fall) Tf = -5 , = 270 - 300 ms 450 ms PE240128WRF-001-HQ VER.0 Page5 Note 2 Note 1. Optical characteristics-2 Viewing angle Rear (12H) =90 Top (=0) L R + - Left (9H) =180 Right (3H) =0 Front (6H) =270 Viewing angle PE240128WRF-001-HQ VER.0 Page6 Note 2. Optical characteristics-3 Fig.2 Definition of response time Positive Type No selected waveform No selected waveform Selected waveform Transmittance 10% 90% 100% Tf Tr Negative Type No selected waveform No selected Selected waveform Transmittance 100% 90% 10% Tr PE240128WRF-001-HQ VER.0 Tf Page7 Electrical characteristics-2 2 Drive waveform Vop: Drive voltage 1/B: Bias N: Duty fF: Frame frequency fD: Drive frequency (1) Selected waveform 1 2 3 N 1 3 2 V Vop/B Vop/B V 1/fD 1/fF (2) Non- Selected waveform 1 2 3 N 1 (1-2/B)Vop Vop/B Vop/B (1-2/B)Vop 1/fF 1/fD Note: Frame frequency is defined as follows: Common side supply voltage peak - to - peak /2 = 1 period PE240128WRF-001-HQ VER.0 Page8 2 3 Note 3. : Definition of Vth Selected waveform 100 73% Transmittanc No selected waveform 50% Vth2 Vth1 Drive Active voltage range View direction Drive waveform Transmittance Vth1 10 (Selected waveform) 50% Vth2 40 (No selected waveform) 73% 1 Contrast ratio = (Brightness in OFF state) / (Brightness in ON state) Outline of Electro-Optical Characteristics Measuring System Photo Detector Human Active Temperatur e Control Chamber LCD Panel Transmissive Measuring System: Autronic DMS-803 PE240128WRF-001-HQ VER.0 Page9 1.6 Backlight Characteristics LCD Module with LED Backlight Maximum Ratings Item Symbol Conditions Min. Max. Unit Forward Current IF Ta =25 - 180 mA Reverse Voltage VR Ta =25 - 5 V Power Dissipation PO Ta =25 - 0.61 W Electrical / Optical Characteristics Ta =25 Item Symbol Conditions Min. Typ. Max. Unit Forward Voltage VF IF= 80 mA - 3.3 3.4 V Reverse Current IR VR= 5V - - 60 uA 0.29 0.32 0.35 CIE Color Coordinate (With LCD) X IF= 80 mA Y 0.35 0.38 0.41 Average Brightness (with LCD) *1 IV IF= 80 mA 30 50 - cd/m2 Uniformity (With LCD)*2 B IF= 80 mA 70 - - % Color White *1 This value will be changed while mass production. *2B=B(min) / B(max) PE240128WRF-001-HQ VER.0 Page10 2. MODULE STRUCTURE 2.1 Counter Drawing 2.1.1 LCM Mechanical Diagram * See Appendix 2.1.2 Block Diagram A LED BACKLIGHT K COM0 ......... COM63 SEG0 SEG239 COM63 .............................. .............................. COM0 PIN34 COM127 SEG239 SEG0 COM80 ......... ......... IC-ST7529 COM64 ... 240 * 128 DOTS LCD PANEL COM143 .............................. PIN1 Please refer interface pin description for detail PE240128WRF-001-HQ VER.0 Page11 2.2 Interface Pin Description Pin No. 1 Symbol A0 Function Register select input pin - A0 = "H": DB0 to DB8 or SI are display data - A0 = "L": DB0 to DB8 or SI are control data Read / Write execution control pin 2 MPU Type RW_WR Description 6800 RW Read / Write control input pin RW = "H" : read RW = "L" : write 8080 /WR Write enable clock input pin The data on DB0 to DB8 are latched at the rising edge of the /WR signal. RW_WR 3 DB0 4 DB1 5 DB2 6 DB3 7 DB4 In IIC Interface 8 DB5 9 DB6 10 DB7 D7: SCL; D6: SI ; D0, D1: SA1, SA0 D3, D2: Acknowledgement D4, D5, D8 should be fixed to VDD or VSS. They connect to the standard 8-bit MPU bus via the 8 bit bi-directional bus.When the following interface is selected and the XCS pin is high, the following pins become highimpedance, which should be fixed to VDD or VSS. Read / Write execution control pin 11 MPU Type RW_WR Description 6800 E Read / Write control input pin -RW = "H": When E is "H", DB0 to DB8 are in an output status. E_RD -RW = "L": The data on DB0 to DB8 are latched at the falling edge of the E signal. 8080 12 RST PE240128WRF-001-HQ /RD Read enable clock input pin When /RD is "L", DB0 to DB8 are in an output status. Reset input pin. When RST is "L", initialization is executed. VER.0 Page12 Pin No. Symbol 13 IF1 14 Function IF3 IF1 IF3 H L 80 series 8-bit parallel L H 68 series 8-bit parallel L L IIC MPU interface type 15 XCS Chip select input pins Data/instruction I/O is enabled only when XCS is "L". When chip select is non-active, DB0 to DB8 may be high impedance. 16 VSS Power supply (VSS=0) 17 VDD Power supply (VDD=3.3V) 18 CAP7P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP7P terminal. 19 CAP1N DC / DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal. 20 CAP5P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP5P terminal. 21 CAP3P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP3P terminal. 22 CAP1N DC / DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal. 23 CAP1P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP1P terminal. 24 CAP2P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP2P terminal. 25 CAP2N DC / DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal. 26 CAP4P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP4P terminal. 27 CAP2N DC / DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal. 28 CAP6P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP6P terminal. 29 VLCD PE240128WRF-001-HQ LCD supply voltage VER.0 Page13 Pin No. Symbol 30 V4 31 V3 32 V2 33 V1 Function LCD driver supply voltages V0In & V0out should be connected together in FPC area. Voltages should have the following relationship: V0 V1 V2 V3 V4 VSS When the internal power circuit is active, these voltages are generated as the following table according to the state of LCD bias. LCD Bias 1/N Bias V1 V2 (N-1) / N x V0 (N-2) / N x V0 (2/N) x V0 NOTE: N = 5 to 14 34 V0 PE240128WRF-001-HQ VER.0 V3 Page14 V4 (1/N) x V0 2.3 Timing Characteristics For the 8080 Series MPU Item Signal Address hold time Address setup time System cycle time Enable L pulse width (Write) Enable H pulse width (Write) Enable L pulse width (Read) Enable H pulse width (Read) WRITE Data setup time WRITE Address hold time READ access time READ Output disable time PE240128WRF-001-HQ VER.0 A0 RW_WR E_RD DB0 to DB7 VDD = 3.3V , Ta = 25C Rating Units Min Max Symbol Condition tAH8 tAW8 tCYC8 tCCLW tCCHW tCCLR - 20 20 200 100 100 100 - tCCHR tDS8 tDH8 tACC8 tOH8 CL=100pF CL=100pF 100 150 20 - 40 30 Page15 ns For the 6800 Series MPU Item Signal Address hold time Address setup time System cycle time Enable L pulse width (Write) Enable H pulse width (Write) Enable L pulse width (Read) Enable H pulse width (Read) WRITE Data setup time WRITE Address hold time READ access time READ Output disable time PE240128WRF-001-HQ VER.0 A0 RW_WR E_RD DB0 to DB7 VDD = 3.3V , Ta = 25C Rating Units Min Max Symbol Condition tAH6 tAW6 tCYC6 tEWLW tEWHW tEWLR - 20 20 200 100 100 100 - tEWHR tDS6 tDH6 tACC6 tOH6 CL=100pF CL=100pF 100 150 20 - 40 30 Page16 ns Reset Timing Item Reset time Reset "L" pulse width PE240128WRF-001-HQ VER.0 Signal Symbol - tR RES tRW Condition - Page17 VDD = 3.3V , Ta = 25C Rating Units Min Typ Max - - 1 s 1 - - s 2.4 Display Command PE240128WRF-001-HQ VER.0 Page18 PE240128WRF-001-HQ VER.0 Page19 3. QUALITY ASSURANCE SYSTEM 3.1 Quality Assurance Flow Chart Item Customer Sales Info Marketing & Design R&D Manufactu Product Inventory Purchase ring control control Q.A Survey Request Project Inquiry evaluation Project Validation NG OK Quote Contract Design check Sample test Sample Approval NG Verification NG OK Sample approval OK Pilot Pilot Run & Mass Product NG Verification OK Specification preparation Mass production OK Ship Out PE240128WRF-001-HQ run & Reliability test Inspection NG Shipment Ship out VER.0 Page20 Item Customer Sales Info Claim R&D Manufact Product Inventory Purchase uring control control Q.A Failure analysis Sales Service Analysis report Corrective action Tracking 1. ISO 9001 Maintenance Activities Q.A 3. Equipment calibration Activity 5. Standardization Management PE240128WRF-001-HQ VER.0 2. Process improvement proposal 4. Education And Training Activities Page21 3.2 Inspection Specification Inspection Standard : MIL-STD-105E Table Normal Inspection Single Sampling Level II Equipment : Gauge , MIL-STD , Powertip Tester , Sample IQC Defect Level : Major Defect AQL 0.4; Minor Defect AQL 1.5 FQC Defect Level : 100% Inspection OUT Going Defect Level : Sampling Specification : NO Item Specification Judge Level The part number is inconsistent with work order of 1 Part Number N.G. Major production The quantity is inconsistent with work order of 2 Quantity N.G. Major production The display lacks of some patterns. N.G. Major Electronic Missing line. N.G. Major characteristics of 3 The size of missing dot, A is > 1/2 Dot size N.G. Major LCM N.G. Major A=( L + W ) 2 There is no function. Output data is error N.G. Major Material is different with work order of production N.G. Major LCD is assembled in inverse direction N.G. Major Bezel is assembled in inverse direction N.G. Major Shadow is within LCD viewing area + 0.5 mm N.G. Major Appearance of The diameter of dirty particle, A is > 0.4 mm N.G. Minor LCD Dirty particle length is > 3.0mm, and 0.01mm < width A=( L + W ) 2 N.G. Minor 0.05mm 4 Display is without protective film N.G. Minor Dirty particle Conductive rubber is over bezel 1mm N.G. Minor (Including N.G. Minor scratchbubble ) Polarizer exceeds over viewing area of LCD Area of bubble in polarizer, A > 1.0mm, the number N.G. Minor of bubble is > 1 piece. 0.4mm < Area of bubble in polarizer, A < 1.0mm, the N.G. Minor number of bubble is > 4 pieces. Burned area or wrong part number is on PCB N.G. Major The symbol, character, and mark of PCB are N.G Minor unidentifiable. The stripped solder mask , A is > 1.0mm N.G. Minor 0.3mm < stripped solder mask or visible circuit, Appearance of N.G. Minor A < 1.0mm, and the number is 4 pieces PCB 5 There is particle between the circuits in solder mask N.G Minor A=( L + W ) 2 The circuit is peeled off or cracked N.G Minor There is any circuits risen or exposed. N.G Minor 0.2mm < Area of solder ball, A is 0.4mm N.G Minor The number of solder ball is 3 pieces The magnitude of solder ball, A is > 0.4mm. N.G Minor PE240128WRF-001-HQ VER.0 Page22 NO 6 7 8 10 Item Specification The shape of modeling is deformed by touching. Appearance of Insufficient epoxy: Circuit or pad of IC is visible molding Excessive epoxy: Diameter of modeling is > 20mm A=( L + W ) 2 or height is > 2.5mm The diameter of pinhole in modeling, A is > 0.2mm. The folding angle of frame must be > 45+ 10 Appearance of The area of stripped electroplate in top-view of frame, A is > 1.0mm. frame A=( L + W ) 2 Rust or crack is (Top view only) The scratched width of frame is > 0.06mm. (Top view only) The color of backlight is nonconforming Electrical Backlight can't work normally. characteristic of The LED lamp can't work normally backlight The unsoldering area of pin for backlight, A=( L + W ) 2 A is > 1/2 solder joint area. The height of solder pin for backlight is > 2.0mm The mark or polarity of component is unidentifiable. The height between bottom of component and surface of the PCB is floating > 0.7mm D > 1/4W W D Assembly parts A=( L + W ) 2 PE240128WRF-001-HQ VER.0 D' Pad End solder joint width, D' is > 50% width of component termination or width of pad Side overhang, D is > 25% width of component termination. Component is cracked, deformed, and burned, etc. The polarity of component is placed in inverse direction. Maximum fillet height of solder extends onto the component body or minimum fillet height is < 0.5mm. Page23 Judge Level N.G. N.G. Major Minor N.G. Minor N.G. N.G. Minor Minor N.G. Minor N.G. Minor N.G. Minor N.G. N.G. N.G. Major Major Major N.G. Minor N.G. N.G. Minor Minor N.G. Minor N.G. Minor N.G. Minor N.G. Minor N.G. Minor N.G. Minor N.G. Minor 4. RELIABILITY TEST 4.1 Reliability Test Condition NO Item 1 High Temperature Storage Storage at 80 2C 96~100 hrs Surrounding temperature, then storage at normal condition 4hrs 2 Low Temperature Storage Storage at -30 2C 96~100 hrs Surrounding temperature, then storage at normal condition 4hrs High Temperature /Humidity Storage 1.Storage 96~100 hrs 60 2C, 90~95%RH surrounding temperature, then storage at normal condition 4hrs. (Excluding the polarizer).or 2.Storage 96~100 hrs 40 2C, 90~95%RH surrounding temperature, then storage at normal condition 4 hrs. 3 4 Temperature Cycling 5 Vibration 6 ESD Test Test Condition -20C 25C 70C 25C (30mins) (5mins) (30mins) (5mins) 10 Cycle 10~55Hz ( 1 minute ) 1.5mm X,Y and Z direction * (each 2hrs) Air Discharge: Contact Discharge: Apply 6 KV with 5 times Apply 250V with 5 times discharge for each polarity +/- discharge for each polarity +/Testing location: Around the face of LCD 7 Drop Test PE240128WRF-001-HQ VER.0 Testing location: 1.Apply to bezel. 2.Apply to Vdd, Vss. Packing Weight (Kg) Drop Height (cm) 0 ~ 45.4 122 45.4 ~ 90.8 76 90.8 ~ 454 61 Over 454 46 Page24 5. PRECAUTION RELATING PRODUCT HANDLING 5.1 SAFETY 5.1.1 5.1.2 If the LCD panel breaks , be careful not to get the liquid crystal to touch your skin. If the liquid crystal touches your skin or clothes , please wash it off immediately by using soap and water. 5.2 HANDLING 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.2.8 5.2.9 Avoid any strong mechanical shock which can break the glass. Avoid static electricity which can damage the CMOS LSI--When working with the module , be sure to ground your body and any electrical equipment you may be using. Do not remove the panel or frame from the module. The polarizing plate of the display is very fragile. So , please handle it very carefully, do not touch , push or rub the exposed polarizing with anything harder than an HB pencil lead (glass , tweezers , etc.) Do not wipe the polarizing plate with a dry cloth , as it may easily scratch the surface of plate. Do not touch the display area with bare hands , this will stain the display area. Do not use ketonics solvent & aromatic solvent. Use with a soft cloth soaked with a cleaning naphtha solvent. To control temperature and time of soldering is 280 10C and 3-5 sec. To avoid liquid (include organic solvent) stained on LCM 5.3 STORAGE 5.3.1 5.3.2 5.3.3 Store the panel or module in a dark place where the temperature is 25C 5C and the humidity is below 65% RH. Do not place the module near organics solvents or corrosive gases. Do not crush , shake , or jolt the module. 5.4 TERMS OF WARRANTY 5.4.1 5.4.2 Applicable warrant period The period is within thirteen months since the date of shipping out under normal using and storage conditions. Unaccepted responsibility This product has been manufactured to your company's specification as a part for use in your company's general electronic products. It is guaranteed to perform according to delivery specifications. For any other use apart from general electronic equipment, we cannot take responsibility if the product is used in nuclear power control equipment, aerospace equipment , fire and security systems or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required. PE240128WRF-001-HQ VER.0 Page25