TL082 TL082 Wide Bandwidth Dual JFET Input Operational Amplifier Literature Number: SNOSBW5B TL082 Wide Bandwidth Dual JFET Input Operational Amplifier General Description Features These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage (BI-FET IITM technology). They require low supply current yet maintain a large gain bandwidth product and fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The TL082 is pin compatible with the standard LM1558 allowing designers to immediately upgrade the overall performance of existing LM1558 and most LM358 designs. n n n n n n n n n n n These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth. The devices also exhibit low noise and offset voltage drift. Typical Connection Internally trimmed offset voltage: Low input bias current: Low input noise voltage: Low input noise current: Wide gain bandwidth: High slew rate: Low supply current: High input impedance: Low total harmonic distortion: Low 1/f noise corner: Fast settling time to 0.01%: 15 mV 50 pA 16nV/Hz 0.01 pA/Hz 4 MHz 13 V/s 3.6 mA 1012 0.02% 50 Hz 2 s Connection Diagram DIP/SO Package (Top View) 00835703 00835701 Order Number TL082CM or TL082CP See NS Package Number M08A or N08E Simplified Schematic 00835702 BI-FET IITM is a trademark of National Semiconductor Corp. (c) 2004 National Semiconductor Corporation DS008357 www.national.com TL082 Wide Bandwidth Dual JFET Input Operational Amplifier August 2000 TL082 Absolute Maximum Ratings (Note 1) Input Voltage Range (Note 3) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Output Short Circuit Duration Continuous Storage Temperature Range -65C to +150C Power Dissipation Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. 0C to +70C Tj(MAX) 150C Differential Input Voltage 30V DC Electrical Characteristics (Note 5) Parameter Conditions TL082C Min VOS Input Offset Voltage RS = 10 k, TA = 25C Typ 5 Over Temperature VOS/T Average TC of Input Offset 260C ESD rating to be determined. (Note 2) Operating Temperature Range Symbol Lead Temp. (Soldering, 10 seconds) 18V Supply Voltage 15V RS = 10 k 10 Tj = 25C, (Notes 5, 6) 25 Units Max 15 mV 20 mV V/C Voltage IOS Input Offset Current Tj 70C IB Input Bias Current Tj = 25C, (Notes 5, 6) RIN Input Resistance Tj = 25C AVOL Large Signal Voltage Gain VS = 15V, TA = 25C 50 Tj 70C 25 200 pA 4 nA 400 pA 8 nA 1012 100 V/mV VO = 10V, RL = 2 k Over Temperature 15 V/mV VO Output Voltage Swing VS = 15V, RL = 10 k VCM Input Common-Mode Voltage VS = 15V 12 11 -12 V CMRR Common-Mode Rejection Ratio RS 10 k 70 100 dB PSRR Supply Voltage Rejection Ratio (Note 7) 70 100 IS Supply Current Range www.national.com 13.5 V +15 V 3.6 2 dB 5.6 mA Symbol TL082 AC Electrical Characteristics (Note 5) Parameter Conditions TL082C Min Amplifier to Amplifier Coupling TA = 25C, f = 1Hz- Typ Units Max -120 dB 20 kHz (Input Referred) SR Slew Rate VS = 15V, TA = 25C 13 V/s GBW Gain Bandwidth Product VS = 15V, TA = 25C 4 MHz en Equivalent Input Noise Voltage TA = 25C, RS = 100, 25 nV/Hz in Equivalent Input Noise Current Tj = 25C, f = 1000 Hz 0.01 pA/Hz THD Total Harmonic Distortion AV = +10, RL = 10k, VO = 20 Vp - p, BW = 20 Hz-20 kHz < 0.02 % 8 f = 1000 Hz Note 2: For operating at elevated temperature, the device must be derated based on a thermal resistance of 115C/W junction to ambient for the N package. Note 3: Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage. Note 4: The power dissipation limit, however, cannot be exceeded. Note 5: These specifications apply for VS = 15V and 0C TA +70C. VOS, IB and IOS are measured at VCM = 0. Note 6: The input bias currents are junction leakage currents which approximately double for every 10C increase in the junction temperature, Tj. Due to the limited production test time, the input bias currents measured are correlated to junction temperature. In normal operation the junction temperature rises above the ambient temperature as a result of internal power dissipation, PD. Tj = TA + jA PD where jA is the thermal resistance from junction to ambient. Use of a heat sink is recommended if input bias current is to be kept to a minimum. Note 7: Supply voltage rejection ratio is measured for both supply magnitudes increasing or decreasing simultaneously in accordance with common practice. VS = 6V to 15V. Typical Performance Characteristics Input Bias Current Input Bias Current 00835719 00835718 3 www.national.com TL082 Typical Performance Characteristics (Continued) Positive Common-Mode Input Voltage Limit Supply Current 00835721 00835720 Negative Common-Mode Input Voltage Limit Positive Current Limit 00835723 00835722 Negative Current Limit Voltage Swing 00835725 00835724 www.national.com 4 TL082 Typical Performance Characteristics (Continued) Output Voltage Swing Gain Bandwidth 00835726 00835727 Bode Plot Slew Rate 00835729 00835728 Undistorted Output Voltage Swing Distortion vs Frequency 00835730 00835731 5 www.national.com TL082 Typical Performance Characteristics (Continued) Open Loop Frequency Response Common-Mode Rejection Ratio 00835733 00835732 Power Supply Rejection Ratio Equivalent Input Noise Voltage 00835734 00835735 Open Loop Voltage Gain (V/V) Output Impedance 00835736 www.national.com 00835737 6 TL082 Typical Performance Characteristics (Continued) Inverter Setting Time 00835738 Pulse Response Large Signal Inverting Small Signal Inverting 00835708 00835706 Large Signal Non-Inverting Small Signal Non-Inverting 00835709 00835707 7 www.national.com TL082 Pulse Response (Continued) Current Limit (RL = 100) 00835710 The amplifiers will drive a 2 k load resistance to 10V over the full temperature range of 0C to +70C. If the amplifier is forced to drive heavier load currents, however, an increase in input offset voltage may occur on the negative voltage swing and finally reach an active current limit on both positive and negative swings. Precautions should be taken to ensure that the power supply for the integrated circuit never becomes reversed in polarity or that the unit is not inadvertently installed backwards in a socket as an unlimited current surge through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a destroyed unit. Because these amplifiers are JFET rather than MOSFET input op amps they do not require special handling. As with most amplifiers, care should be taken with lead dress, component placement and supply decoupling in order to ensure stability. For example, resistors from the output to an input should be placed with the body close to the input to minimize "pick-up" and maximize the frequency of the feedback pole by minimizing the capacitance from the input to ground. Application Hints These devices are op amps with an internally trimmed input offset voltage and JFET input devices (BI-FET II). These JFETs have large reverse breakdown voltages from gate to source and drain eliminating the need for clamps across the inputs. Therefore, large differential input voltages can easily be accommodated without a large increase in input current. The maximum differential input voltage is independent of the supply voltages. However, neither of the input voltages should be allowed to exceed the negative supply as this will cause large currents to flow which can result in a destroyed unit. Exceeding the negative common-mode limit on either input will cause a reversal of the phase to the output and force the amplifier output to the corresponding high or low state. Exceeding the negative common-mode limit on both inputs will force the amplifier output to a high state. In neither case does a latch occur since raising the input back within the common-mode range again puts the input stage and thus the amplifier in a normal operating mode. Exceeding the positive common-mode limit on a single input will not change the phase of the output; however, if both inputs exceed the limit, the output of the amplifier will be forced to a high state. The amplifiers will operate with a common-mode input voltage equal to the positive supply; however, the gain bandwidth and slew rate may be decreased in this condition. When the negative common-mode voltage swings to within 3V of the negative supply, an increase in input offset voltage may occur. Each amplifier is individually biased by a zener reference which allows normal circuit operation on 6V power supplies. Supply voltages less than these may result in lower gain bandwidth and slew rate. www.national.com A feedback pole is created when the feedback around any amplifier is resistive. The parallel resistance and capacitance from the input of the device (usually the inverting input) to AC ground set the frequency of the pole. In many instances the frequency of this pole is much greater than the expected 3 dB frequency of the closed loop gain and consequently there is negligible effect on stability margin. However, if the feedback pole is less than approximately 6 times the expected 3 dB frequency a lead capacitor should be placed from the output to the input of the op amp. The value of the added capacitor should be such that the RC time constant of this capacitor and the resistance it parallels is greater than or equal to the original feedback pole time constant. 8 TL082 Detailed Schematic 00835711 Typical Applications Three-Band Active Tone Control 00835712 9 www.national.com TL082 Typical Applications (Continued) 00835713 * All potentiometers are linear taper * Use the LF347 Quad for stereo applications Note 8: All controls flat. Note 9: Bass and treble boost, mid flat. Note 10: Bass and treble cut, mid flat. Note 11: Mid boost, bass and treble flat. Note 12: Mid cut, bass and treble flat. Improved CMRR Instrumentation Amplifier 00835714 C and are separate isolated grounds Matching of R2's, R4's and R5's control CMRR With AVT = 1400, resistor matching = 0.01%: CMRR = 136 dB * Very high input impedance * Super high CMRR www.national.com 10 TL082 Typical Applications (Continued) Fourth Order Low Pass Butterworth Filter 00835715 Fourth Order High Pass Butterworth Filter 00835716 11 www.national.com TL082 Typical Applications (Continued) Ohms to Volts Converter 00835717 www.national.com 12 TL082 Physical Dimensions inches (millimeters) unless otherwise noted Order Number TL082CM NS Package M08A Order Number TL082CP NS Package N08E 13 www.national.com TL082 Wide Bandwidth Dual JFET Input Operational Amplifier Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated