Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
Monolithic Linear IC
6W 2-Channel, Bridge 19W typ Power Amplifier
Ordering number:ENN750F
LA4440
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
21500TH (KT)/90196RM/33194HO/8064KI/3233KI/O070KI, TS No.750–1/13
Package Dimensions
unit:mm
3023A-SIP14H
[LA4440]
SANYO : SIP14H
Features
• Built-in 2 channels (dual) enabling use in stereo and bridge
amplifier applications.
Dual : 6W×2 (typ.)
Bridge : 19W (typ.)
• Minimun number of external parts required.
• Small pop noise at the time of power suppl y ON/OFF and
good starting balance.
• Good ripple rejection : 46dB (typ.)
• Good channel separation.
• Small residual noise (Rg=0).
• Lo w distortion ov er a wide range from lo w frequencies to
high frequencies.
• Easy to design radiator fin.
• Built-in audio muting function.
• Built-in protectors.
a. Thermal protector
b. Overvoltage, surge voltage protector
c. Pin-to-pin short protector
Specifications
Absolute Maximum Ratings at Ta = 25˚C
˚C
˚C
14
1
13.8
0.6
37.0
30.0
R1.7
11.0
8.0
0.8min
6.0 15.0max
1.99 2.54 1.4 0.4
4.5
2.25
retemaraPlobmySsnoitidnoCsgnitaRtinU
egatlovylppusmumixaM VCC 1xam)s03=t(tnecseiuQ 52V
VCC 2xamgnitarepO 81V
egatlovylppusegruS
VCC )egrus(
t≤s2.0 05V
noitapissidrewopelbawollAxamdP 51W
ecnatsiserlamreT θc-j esac-ot-noitcnuJ 3
erutarepmetgnitarepOrpoT 57+ot02–
erutarepmetegarotSgtsT 051+ot04–
˚C/W
Recommended Operating Conditions at Ta = 25˚C
Tc=75˚C, See Pd max – Ta characteristic
retemaraPlobmySsnoitidnoCsgnitaRtinU
egatlovylppuSV
CC 2.31V
ecnatsiserdaoLR
LoeretS 8ot2 Ω
egdirB 8ot4 Ω
LA4440
No.750–2/13
Operating Characteristics at Ta = 25˚C, VCC=13.2V, RL=4Ω, f=1kHz, Rg=600Ω, with 100×100×1.5mm3 Al f in,
See specified Test Circuit.
retemaraPlobmySsnoitidnoC sgnitaR tinU
nimpytxam
tnerructnecseiuQoccI 001002Am
niagegatloVGV5.945.155.35Bd
rewoptuptuOP
OoeretS,%01=DHT0.50.6W
egdirB,%01=DHT91W
noitrotsidcinomrahlatoTDHTP
OW1=1.00.1%
ecnatsisertupnIr
ik03 Ω
egatlovesiontuptuOV
ON 0=gR6.00.1Vm
k01=gR Ω0.10.2Vm
oitarnoitcejerelppiRR
rVRf,Vm002= R0=gR,zH001=64Bd
noitarapeslennahCpeshCV
Ok01=gR,mBd0= Ω5455Bd
noitaunettagnituMTTAV
OV,mBd0= MV9=04Bd
slennahcneewtebecnereffidniaG ∆GV 2Bd
Equivalent Circuit Block Diagram
LA4440
No.750–3/13
Sample Application Circuit 1. Stereo use
Sample Application Circuit 2. Bridge amplifier 1
LA4440
No.750–4/13
Sample Application Circuit 3. Bridge amplifier 2
Description of External Parts
C1 (C2) · Feedback capacitor : The low cutoff frequency depends on this capacitor.
If the capacitance value is increased, the starting time is delayed.
C3 (C4) · Bootstrap capacitor : If the capacitance value is decreased, the output at low frequencies goes lower.
C5 (C6) · Oscillation preventing capacitor : Polyester film capacitor, being good in temperature characteristic,
frequency characteristic, is used.
The capacitance value can be reduced to 0.047µF depending on the stability of the board.
C7 (C8) · Output capacitor : The low cutoff frequency depends on this capacitor.
At the bridge amplifier mode, the output capacitor is generally connected.
C9 · Decoupling capacitor :Used for the ripple filter. Since the rejection effect is saturated at a certain
capacitance value, it is meaningless to increase the capacitance value more than required. This capaci-
tor, being also used for the time constant of the muting circuit, affects the starting time.
R1 (R2) · Filter resistor for preventing oscillation.
R3 (R4) · Resistor for making input signal of inverting amplifier in Voltage Gain Adjust at Bridge Amplifier
Mode (No. 1).
R5 · Resistor for adjusting starting time in Voltage Gain Adjust at Bridge Amplifier Mode (No. 2)
C10 · Capacitor for preventing oscillation in Voltage Gain Adjust at Bridge Amplifier Mode (No. 2)
C11 · Power source capacitor.
R6 (R7) · Used at bridge amplifier mode in order to increase discharge speed and to secure transient stability.
Feaures of IC System and Functions of Remaining Pins
(a) Since the input circuit uses PNP transistors and the input potential is designed to be 0 bias, no input coupling
capacitor is required and direct coupling is available. However, when slider contact noise caused by the variable
resistor presents a problem, connect an capacitor in series with the input.
(b) The open-loop voltage gain is lowered and the negative feedback amount is reduced for stabilization. An increase
in distortion resulted from the reduced negative feedback amount is avoided by use of the built-in unique distor-
tion reduction circuit, and thus distortion is kept at 0.1% (typ.).
(c) A capacitor for oscillation compensation is contained as a means of reducing the number of external parts. The
capacitance value is 35pF which determines high cutoff frequency fH (–3dB point) of the amplifier (fH≈20kHz).
(d) For preventing the IC from being damaged by a surge applied on the power line, an overvoltage protector is
contained. Overvoltage setting is 25V. It is capable of withstanding up to 50V at giant pulse surge 200ms.
(e) No damege occurs even when power is applied at a state where pins 10, 11, and 12 are short-circuited with solder
bridge, etc.
(f) To minimize the variations in voltage gain, feedback resistor RNF is contained and voltage gain (51.5dB) is fixed.
LA4440
No.750–5/13
Voltage Gain Adjust at Stereo Mode
RNF=50Ω (typ), Rf=20kΩ (typ)
At RNF’=0 (recommended VG)
VG=20log (dB)
In case of using RNF’
VG=20log (dB)
VG
RNF
Rf
RNF+RNF’
Voltage Gain Adjust at Bridge Amplifier Mode (No. 1)
· The bridge amplifier configuration is as shown left, in
which ch1 and ch2 operate as noninverting amplifier
and inverting amplifier respectively.
The output of the noninverting amplifier divided by
resistors R3, R4 is applied, as input, to the inverting
amplifier.
Since attenuation (R4/R3) of the non-inverting amplifier
output and amplification factor (Rf/R4+RNF) of the
inverting amplifier are fixed to be the same, signals of
the same level and 180° out of phase with each other
can be obtained at output pins (12) and (10). The total
voltage gain is apparently higher than that of the
noninverting amplifier by 6dB and is approximately
calculated by the following formula.
VG=20log + 6dB
In case of reducing the voltage gain, RNF’ is connected
to the noninverting amplifier side only and the following
formula is used.
VG=20log + 6dB
VG=20log (dB)
where (RNF+RNF’) << R5
From this formula, it is seen that connecting RNF’
causes the voltage gain to be reduced at the modes of
both stereo amplifier and bridge amplifier.
Rf
RNF
Voltage Gain Adjust at Bridge Amplifier Mode (No. 2)
Rf
RNF+RNF’
Rf
RNF+RNF’
2
LA4440
No.750–6/13
(g) In case of applying audio muting in each application circuit, the following circuit is used.
6V≤VM≤VCC
Recommended VM=9V
ATT=40dB (Rg=600Ω)
Flow-in current IO is calculated by the following formula.
IO=
In case of increasing the muting attenuation, resistor 5.6kΩ is connected in series with the input, and then the
attenuation is made to be 55dB. Be careful that connecting an input capacitor causes pop noise to be increased at
the time of application of AC muting. Increased RO, CO make it possible to reduce the noise. In case of com-
pletely cutting off power IC, pin (5) is grounded, and then DC control is available and the attenuation is made to
be ∞.
VM – VBE
RO
Stereo : 20Ω≤R≤100Ω
Bridge No.1 : 20Ω≤R≤100Ω
Bridge No. 2 : 0Ω≤R≤50Ω
Pin Voltage (unit : V)
.oNniP 123456789 0111213141
nipnoitcnuF 1HC FN 1HC FN erP DNG
CA oiduA gnituM CD 2HCNI 2HC FN
2HC rewoP DNG
2HC SB 2HC TUO VCC 1HC TUO 1HC SB
1HC rewoP DNG
taegatloVniP edomtnecseiuq 4.130.0000.3130.04.10 9.118.62.318.69.110
Proper Cares in Using IC
· Maximum ratings
If the IC is used in the vicinity of the maximum ratings, even a slight variation in conditions may cause the maximum
ratings to be exceeded, thereby leading to breakdown. Allow an ample margin of va riation for supply voltage, etc. and
use the IC in the range where the maximum ratings are not exceeded.
· Printed circuit board
When making the board, refer to the sample printed circuit pattern and be careful that no feedback loop is formed
between input and output.
· Oscillation preventing capacitor
Normally, a polyester film capacitor is used for 0.1µF + 4.7Ω. The capacitance value can be reduced to 0.047µF depend-
ing on the stability of the board.
· Others
Connect the radiator fin of the package to GND.
LA4440
No.750–7/13
Characteristics at stereo amplifier mode
LA4440
No.750–8/13
LA4440
No.750–9/13
Characteristics at bridge amplifier mode No. 1
LA4440
No.750–10/13
LA4440
No.750–11/13
Characteristics at bridge amplifier mode No. 2
LA4440
No.750–12/13
Proper Cares in Mounging Radiator Fin
1. The mounting torque is in the range of 39 to 59N · cm.
2. The distance between screw holes of the radiator fin must coincide with the distance between screw holes of the IC.
With case outline dimensions L and R referred to, the screws must be tightened with the distance between them as
close to each other as possible.
3. The scre w to be used must ha v e a head equivalent to the one of truss machine scre w or binder mac hine screw defined
by JIS. Washers must be also used to protect the IC case.
4. No foreign matter such as cutting particles shall exist between heat sink and radia tor fin. When applying grease on the
junction surface, it must be applied uniformly on the whole surface.
5. IC lead pins are soldered to the printed circuit board after the radiator fin is mounted on the IC.
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer's
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer's products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be exported without obtaining the export license from the authorities
concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co. , Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of February, 2000. Specifications and information herein are subject
to change without notice.
LA4440
PS No.750–13/13
